| Age | Commit message (Collapse) | Author |
|---|
|
When bridged ports and standalone ports share a VLAN, e.g. via VLAN
uppers, or untagged traffic with a vlan unaware bridge, the ASIC will
still try to forward traffic to known FDB entries on standalone ports.
But since the port VLAN masks prevent forwarding to bridged ports, this
traffic will be dropped.
This e.g. can be observed in the bridge_vlan_unaware ping tests, where
this breaks pinging with learning on.
Work around this by enabling the simplified EAP mode on switches
supporting it for standalone ports, which causes the ASIC to redirect
traffic of unknown source MAC addresses to the CPU port.
Since standalone ports do not learn, there are no known source MAC
addresses, so effectively this redirects all incoming traffic to the CPU
port.
Fixes: ff39c2d68679 ("net: dsa: b53: Add bridge support")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250508091424.26870-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for new pci device id 0x1641 to register
Renoir device with PCIe.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509155325.720499-6-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A new version of XPCS access routines have been introduced, add the
support to xgbe_pci_probe() to use these routines.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509155325.720499-5-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add the necessary support to enable Renoir ethernet device. Since the
BAR1 address cannot be used to access the XPCS registers on Renoir, use
the smn functions.
Some of the ethernet add-in-cards have dual PHY but share a single MDIO
line (between the ports). In such cases, link inconsistencies are
noticed during the heavy traffic and during reboot stress tests. Using
smn calls helps avoid such race conditions.
Suggested-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509155325.720499-4-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Reorganize the xgbe_pci_probe() code path to convert if/else statements
to switch case to help add future code. This helps code look cleaner.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509155325.720499-3-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The xgbe_{read/write}_mmd_regs_v* functions have common code which can
be moved to helper functions. Add new helper functions to calculate the
mmd_address for v1/v2 of xpcs access.
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509155325.720499-2-Raju.Rangoju@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If the caller wrote more characters, count is truncated to the max
available space in "simple_write_to_buffer". Check that the input
size does not exceed the buffer size. Write a zero termination
afterwards.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505091754.285hHbr2-lkp@intel.com/
Signed-off-by: Markus Burri <markus.burri@mt.com>
Link: https://lore.kernel.org/r/20250509150459.115489-1-markus.burri@mt.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
If an input changes state during wake-up and is used as an interrupt
source, the IRQ handler reads the volatile input register to clear the
interrupt mask and deassert the IRQ line. However, the IRQ handler is
triggered before access to the register is granted, causing the read
operation to fail.
As a result, the IRQ handler enters a loop, repeatedly printing the
"failed reading register" message, until `pca953x_resume()` is eventually
called, which restores the driver context and enables access to
registers.
Fix by disabling the IRQ line before entering suspend mode, and
re-enabling it after the driver context is restored in `pca953x_resume()`.
An IRQ can be disabled with disable_irq() and still wake the system as
long as the IRQ has wake enabled, so the wake-up functionality is
preserved.
Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Cc: stable@vger.kernel.org
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250512095441.31645-1-francesco@dolcini.it
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
We don't need the CORES() match nor jacket (which really doesn't
even make sense to match to the RF anyway), and since the subdevice
masks we care about are contiguous, we can encode them as highest
and lowest bit set (automatically.) By encoding whether to match or
not as separate flags and taking advantage of the limited range of
the RF type, step and ID we can reduce the amount of memory needed
for the table, while also making the logic (apart perhaps from the
subdevice mask) easier to understand.
This reduces the size of the module by about 1.5KiB on x86-64.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.38a805a7c96f.Ieece00476cea6054b0827cd075eb8ba5943373df@changeid
|
|
Use netmem_dma_*() helpers in gve_tx_dqo.c DQO-RDA paths to
enable netmem TX support in that mode.
Declare support for netmem TX in GVE DQO-RDA mode.
Signed-off-by: Mina Almasry <almasrymina@google.com>
Acked-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250508004830.4100853-8-almasrymina@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The KSZ9477 PHY driver contained workarounds for broken EEE capability
advertisements by manually masking supported EEE modes and forcibly
disabling EEE if MICREL_NO_EEE was set.
With proper MAC-side EEE handling implemented via phylink, these quirks
are no longer necessary. Remove MICREL_NO_EEE handling and the use of
ksz9477_get_features().
This simplifies the PHY driver and avoids duplicated EEE management logic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # v6.14+
Link: https://patch.msgid.link/20250504081434.424489-3-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Phylink expects MAC drivers to provide LPI callbacks to properly manage
Energy Efficient Ethernet (EEE) configuration. On KSZ switches with
integrated PHYs, LPI is internally handled by hardware, while ports
without integrated PHYs have no documented MAC-level LPI support.
Provide dummy mac_disable_tx_lpi() and mac_enable_tx_lpi() callbacks to
satisfy phylink requirements. Also, set default EEE capabilities during
phylink initialization where applicable.
Since phylink can now gracefully handle optional EEE configuration,
remove the need for the MICREL_NO_EEE PHY flag.
This change addresses issues caused by incomplete EEE refactoring
introduced in commit fe0d4fd9285e ("net: phy: Keep track of EEE
configuration"). It is not easily possible to fix all older kernels, but
this patch ensures proper behavior on latest kernels and can be
considered for backporting to stable kernels starting from v6.14.
Fixes: fe0d4fd9285e ("net: phy: Keep track of EEE configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # v6.14+
Link: https://patch.msgid.link/20250504081434.424489-2-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The flag NVMET_PCI_EPF_Q_IS_SQ is set but never used. Remove it.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Improve the debug message of nvmet_pci_epf_create_cq() to indicate if a
completion queue IRQ is disabled.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
There is no point in taking the controller irq_lock and calling
nvmet_pci_epf_should_raise_irq() for a completion queue which does not
have IRQ enabled (NVMET_PCI_EPF_Q_IRQ_ENABLED flag is not set).
Move the test for the NVMET_PCI_EPF_Q_IRQ_ENABLED flag out of
nvmet_pci_epf_should_raise_irq() to the top of nvmet_pci_epf_raise_irq()
to return early when no IRQ should be raised.
Also, use dev_err_ratelimited() to avoid a message storm under load when
raising IRQs is failing.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some endpoint PCIe controllers do not support raising legacy INTX
interrupts. This support is indicated by the intx_capable field of
struct pci_epc_features. Modify nvmet_pci_epf_raise_irq() to not
automatically fallback to trying raising an INTX interrupt after an MSI
or MSI-X error if the controller does not support INTX.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The function nvmet_pci_epf_delete_cq() unconditionally calls
nvmet_pci_epf_remove_irq_vector() even for completion queues that do not
have interrupts enabled. Furthermore, for completion queues that do
have IRQ enabled, deleting and re-creating the completion queue leaves
the flag NVMET_PCI_EPF_Q_IRQ_ENABLED set, even if the completion queue
is being re-created with IRQ disabled.
Fix these issues by calling nvmet_pci_epf_remove_irq_vector() only if
NVMET_PCI_EPF_Q_IRQ_ENABLED is set and make sure to always clear that
flag.
Fixes: 0faa0fe6f90e ("nvmet: New NVMe PCI endpoint function target driver")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
We need to lock this queue for that condition because the timeout work
executes per-namespace and can poll the poll CQ.
Reported-by: Hannes Reinecke <hare@kernel.org>
Closes: https://lore.kernel.org/all/20240902130728.1999-1-hare@kernel.org/
Fixes: a0fa9647a54e ("NVMe: add blk polling support")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The only reason nvme_pci_npages_prp() could be used as a compile-time
known result in BUILD_BUG_ON() is because the compiler was always choosing
to inline the function. Under special circumstances (sanitizer coverage
functions disabled for __init functions on ARCH=um), the compiler decided
to stop inlining it:
drivers/nvme/host/pci.c: In function 'nvme_init':
include/linux/compiler_types.h:557:45: error: call to '__compiletime_assert_678' declared with attribute error: BUILD_BUG_ON failed: nvme_pci_npages_prp() > NVME_MAX_NR_ALLOCATIONS
557 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^
include/linux/compiler_types.h:538:25: note: in definition of macro '__compiletime_assert'
538 | prefix ## suffix(); \
| ^~~~~~
include/linux/compiler_types.h:557:9: note: in expansion of macro '_compiletime_assert'
557 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
| ^~~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
39 | #define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
| ^~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:50:9: note: in expansion of macro 'BUILD_BUG_ON_MSG'
50 | BUILD_BUG_ON_MSG(condition, "BUILD_BUG_ON failed: " #condition)
| ^~~~~~~~~~~~~~~~
drivers/nvme/host/pci.c:3804:9: note: in expansion of macro 'BUILD_BUG_ON'
3804 | BUILD_BUG_ON(nvme_pci_npages_prp() > NVME_MAX_NR_ALLOCATIONS);
| ^~~~~~~~~~~~
Force it to be __always_inline to make sure it is always available for
use with BUILD_BUG_ON().
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505061846.12FMyRjj-lkp@intel.com/
Fixes: c372cdd1efdf ("nvme-pci: iod npages fits in s8")
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The REPORT ZONES buffer size is currently limited by the HBA's maximum
segment count to ensure the buffer can be mapped. However, the block
layer further limits the number of iovec entries to 1024 when allocating
a bio.
To avoid allocation of buffers too large to be mapped, further restrict
the maximum buffer size to BIO_MAX_INLINE_VECS.
Replace the UIO_MAXIOV symbolic name with the more contextually
appropriate BIO_MAX_INLINE_VECS.
Fixes: b091ac616846 ("sd_zbc: Fix report zones buffer allocation")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Siwinski <ssiwinski@atto.com>
Link: https://lore.kernel.org/r/20250508200122.243129-1-ssiwinski@atto.com
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
b53 supported switches support configuring ageing time between 1 and
1,048,575 seconds, so add an appropriate setter.
This allows b53 to pass the FDB learning test for both vlan aware and
vlan unaware bridges.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250510092211.276541-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As mlx4 has implemented skb_tx_timestamp() in mlx4_en_xmit(), the
SOFTWARE flag is surely needed when users are trying to get timestamp
information.
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250510093442.79711-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/linux
Tony Nguyen says:
====================
Prepare for Intel IPU E2000 (GEN3)
This is the first part in introducing RDMA support for idpf.
----------------------------------------------------------------
Tatyana Nikolova says:
To align with review comments, the patch series introducing RDMA
RoCEv2 support for the Intel Infrastructure Processing Unit (IPU)
E2000 line of products is going to be submitted in three parts:
1. Modify ice to use specific and common IIDC definitions and
pass a core device info to irdma.
2. Add RDMA support to idpf and modify idpf to use specific and
common IIDC definitions and pass a core device info to irdma.
3. Add RDMA RoCEv2 support for the E2000 products, referred to as
GEN3 to irdma.
This first part is a 5 patch series based on the original
"iidc/ice/irdma: Update IDC to support multiple consumers" patch
to allow for multiple CORE PCI drivers, using the auxbus.
Patches:
1) Move header file to new name for clarity and replace ice
specific DSCP define with a kernel equivalent one in irdma
2) Unify naming convention
3) Separate header file into common and driver specific info
4) Replace ice specific DSCP define with a kernel equivalent
one in ice
5) Implement core device info struct and update drivers to use it
----------------------------------------------------------------
v1: https://lore.kernel.org/20250505212037.2092288-1-anthony.l.nguyen@intel.com
IWL reviews:
[v5] https://lore.kernel.org/20250416021549.606-1-tatyana.e.nikolova@intel.com
[v4] https://lore.kernel.org/20250225050428.2166-1-tatyana.e.nikolova@intel.com
[v3] https://lore.kernel.org/20250207194931.1569-1-tatyana.e.nikolova@intel.com
[v2] https://lore.kernel.org/20240824031924.421-1-tatyana.e.nikolova@intel.com
[v1] https://lore.kernel.org/20240724233917.704-1-tatyana.e.nikolova@intel.com
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/linux:
iidc/ice/irdma: Update IDC to support multiple consumers
ice: Replace ice specific DSCP mapping num with a kernel define
iidc/ice/irdma: Break iidc.h into two headers
iidc/ice/irdma: Rename to iidc_* convention
iidc/ice/irdma: Rename IDC header file
====================
Link: https://patch.msgid.link/20250509200712.2911060-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function mse102x_rx_pkt_spi is used in two cases:
* initial polling to re-arm RX interrupt
* level based RX interrupt handler
Both of them doesn't need an open-coded retry mechanism.
In the first case the function can be called again, if the return code
is IRQ_NONE. This keeps the error behavior during netdev open.
In the second case the proper retry would be handled implicit by
the SPI interrupt. So drop the retry code and simplify the receive path.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-7-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MSE102x doesn't provide any interrupt register, so the only way
to handle the level interrupt is to fetch the whole packet from
the MSE102x internal buffer via SPI. So in cases the interrupt
handler fails to do this, it should return IRQ_NONE. This allows
the core to disable the interrupt in case the issue persists
and prevent an interrupt storm.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20250509120435.43646-6-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After removal of the invalid command counter only a relevant debug
message is left, which can be cumbersome. So add a new flag to debugfs,
which indicates whether the driver has ever received a valid CMD.
This helps to differentiate between general and temporary receive
issues.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250509120435.43646-5-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There are several reasons for an invalid command response
by the MSE102x:
* SPI line interferences
* MSE102x is in reset or has no firmware
* MSE102x is busy
* no packet in MSE102x receive buffer
So the counter for invalid command isn't very helpful without
further context. So drop the confusing statistics counter,
but keep the debug messages about "unexpected response" in order
to debug possible hardware issues.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250509120435.43646-4-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The example of the initial DT binding of the Vertexcom MSE 102x suggested
a IRQ_TYPE_EDGE_RISING, which is wrong. So warn everyone to fix their
device tree to level based IRQ.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250509120435.43646-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It has been reported that when under a bridge with stp_state=1, the logs
get spammed with this message:
[ 251.734607] fsl_dpaa2_eth dpni.5 eth0: Couldn't decode source port
Further debugging shows the following info associated with packets:
source_port=-1, switch_id=-1, vid=-1, vbid=1
In other words, they are data plane packets which are supposed to be
decoded by dsa_tag_8021q_find_port_by_vbid(), but the latter (correctly)
refuses to do so, because no switch port is currently in
BR_STATE_LEARNING or BR_STATE_FORWARDING - so the packet is effectively
unexpected.
The error goes away after the port progresses to BR_STATE_LEARNING in 15
seconds (the default forward_time of the bridge), because then,
dsa_tag_8021q_find_port_by_vbid() can correctly associate the data plane
packets with a plausible bridge port in a plausible STP state.
Re-reading IEEE 802.1D-1990, I see the following:
"4.4.2 Learning: (...) The Forwarding Process shall discard received
frames."
IEEE 802.1D-2004 further clarifies:
"DISABLED, BLOCKING, LISTENING, and BROKEN all correspond to the
DISCARDING port state. While those dot1dStpPortStates serve to
distinguish reasons for discarding frames, the operation of the
Forwarding and Learning processes is the same for all of them. (...)
LISTENING represents a port that the spanning tree algorithm has
selected to be part of the active topology (computing a Root Port or
Designated Port role) but is temporarily discarding frames to guard
against loops or incorrect learning."
Well, this is not what the driver does - instead it sets
mac[port].ingress = true.
To get rid of the log spam, prevent unexpected data plane packets to
be received by software by discarding them on ingress in the LISTENING
state.
In terms of blame attribution: the prints only date back to commit
d7f9787a763f ("net: dsa: tag_8021q: add support for imprecise RX based
on the VBID"). However, the settings would permit a LISTENING port to
forward to a FORWARDING port, and the standard suggests that's not OK.
Fixes: 640f763f98c2 ("net: dsa: sja1105: Add support for Spanning Tree Protocol")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250509113816.2221992-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Most PHY drivers default to a 2ns delay if internal delay is requested
and no value is specified. Having a default value makes sense, as it
allows a Device Tree to only care about board design (whether there are
delays on the PCB or not), and not whether the delay is added on the MAC
or the PHY side when needed.
Whether the delays are actually applied is controlled by the
DP83867_RGMII_*_CLK_DELAY_EN flags, so the behavior is only changed in
configurations that would previously be rejected with -EINVAL.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://patch.msgid.link/e2509b248a11ee29ea408a50c231da4c1fa0863b.1746612711.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The check that intended to handle "rgmii" PHY mode differently to the
RGMII modes with internal delay never worked as intended:
- added in commit 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy"):
logic error caused the condition to always evaluate to true
- changed in commit a46fa260f6f5 ("net: phy: dp83867: Fix warning check
for setting the internal delay"): now the condition incorrectly
evaluates to false for rgmii-txid
- removed in commit 2b892649254f ("net: phy: dp83867: Set up RGMII TX
delay")
Around the time of the removal, commit c11669a2757e ("net: phy: dp83867:
Rework delay rgmii delay handling") started clearing the delay enable
flags in RGMIICTL. The change attempted to preserve the historical
behavior of not disabling internal delays with "rgmii" PHY mode and also
documented this in a comment, but due to a conflict between "Set up
RGMII TX delay" and "Rework delay rgmii delay handling", the behavior
dp83867_verify_rgmii_cfg() warned about (and that was also described in
a comment in dp83867_config_init()) disappeared in the following merge
of net into net-next in commit b4b12b0d2f02
("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net").
While is doesn't appear that this breaking change was intentional, it
has been like this since 2019, and the new behavior to disable the delays
with "rgmii" PHY mode is generally desirable - in particular with MAC
drivers that have to fix up the delay mode, resulting in the PHY driver
not even seeing the same mode that was specified in the Device Tree.
Remove the obsolete check and comment.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://patch.msgid.link/8a286207cd11b460bb0dbd27931de3626b9d7575.1746612711.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a situation where after THALT is set high, TGO stays high as
well. Because jiffies are never updated, as we are in a context with
interrupts disabled, we never exit that loop and have a deadlock.
That deadlock was noticed on a sama5d4 device that stayed locked for days.
Use retries instead of jiffies so that the timeout really works and we do
not have a deadlock anymore.
Fixes: e86cd53afc590 ("net/macb: better manage tx errors")
Signed-off-by: Mathieu Othacehe <othacehe@gnu.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250509121935.16282-1-othacehe@gnu.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
New timestamping API was introduced in commit 66f7223039c0 ("net: add
NDOs for configuring hardware timestamping") from kernel v6.6. It is
time to convert the intel ixp4xx ethernet driver to the new API, so that
the ndo_eth_ioctl() path can be removed completely.
hwtstamp_get() and hwtstamp_set() are only called if netif_running()
when the code path is engaged through the legacy ioctl. As I don't
want to make an unnecessary functional change which I can't test,
preserve that restriction when going through the new operations.
When cpu_is_ixp46x() is false, the execution of SIOCGHWTSTAMP and
SIOCSHWTSTAMP falls through to phy_mii_ioctl(), which may process it in
case of a timestamping PHY, or may return -EOPNOTSUPP. In the new API,
the core handles timestamping PHYs directly and does not call the netdev
driver, so just return -EOPNOTSUPP directly for equivalent logic.
A gratuitous change I chose to do anyway is prefixing hwtstamp_get() and
hwtstamp_set() with the driver name, ipx4xx. This reflects modern coding
sensibilities, and we are touching the involved lines anyway.
The remainder of eth_ioctl() is exactly equivalent to
phy_do_ioctl_running(), so use that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250508211043.3388702-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Having a software timestamp (along with existing hardware one) is
useful to trace how the packets flow through the stack.
mlx5e_tx_skb_update_hwts_flags is called from tx paths
to setup HW timestamp; extend it to add software one as well.
Reviewed-by: Jason Xing <kerneljasonxing@gmail.com>
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250508235109.585096-1-stfomichev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform drivers fixes from Ilpo Järvinen:
- amd/pmc: Use spurious 8042 quirk with MECHREVO Wujie 14XA
- amd/pmf:
- Ensure Smart PC policies are valid
- Fix memory leak when the engine fails to start
- amd/hsmp: Make amd_hsmp and hsmp_acpi as mutually exclusive drivers
- asus-wmi: Fix wlan_ctrl_by_user detection
- thinkpad_acpi: Add support for NEC Lavie X1475JAS
* tag 'platform-drivers-x86-v6.15-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: asus-wmi: Fix wlan_ctrl_by_user detection
platform/x86/amd/pmc: Declare quirk_spurious_8042 for MECHREVO Wujie 14XA (GX4HRXL)
platform/x86: thinkpad_acpi: Support also NEC Lavie X1475JAS
platform/x86/amd/hsmp: Make amd_hsmp and hsmp_acpi as mutually exclusive drivers
drivers/platform/x86/amd: pmf: Check for invalid Smart PC Policies
drivers/platform/x86/amd: pmf: Check for invalid sideloaded Smart PC Policies
|
|
We don't need the configs that won't end up being used, such as
the "br" config for discrete devices, remove them. Also remove
the module firmware for test chips, that's never needed.
For now keep the iwl_dr_mac_cfg even if it's unused, we'll add
platforms with it once we have their PCI IDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.15e2056ec40f.I75a6ce4ad0b14d2b4413615f05523a8f62f08954@changeid
|
|
Add iwl_trans_get_device_id() to extract the device ID
from the hw_id member in the iwl_trans structure.
hw_id member contains both sub-device ID and device ID,
with the device ID occupying bits 16 to 31.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.4411402701f2.I81cde20de05e3bb993977f8d4bbf90707819347f@changeid
|
|
Looks like these were never marked discrete, since they always
used the iwl_so_mac_cfg (earlier iwl_so_trans_cfg). Mark them
as discrete since they are.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
PerCI-Ready: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Tested-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250511195137.f3a75ae80f28.I79964f4426389f04798b70841a9e847be48bf9c3@changeid
|
|
Now that it's all split into MAC and RF configs, remove
the matching on MAC type and step. If we ever need to do
something based on the MAC step, we'll have to find some
new mechanism (since the MAC type is known already from
the PCI IDs table, but not the step), or just handle the
(likely small) differences in code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.fca99a5ab315.Iae27b781221fd29845493adf2c29d9e4f7a9c33b@changeid
|
|
There are some devices that are misidentified, such as 7265-N
and Killer 1435 variants. Add their names, and for some of them
also add the PCI IDs to match at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.ca03a90c294e.I04d64964c664d49ab16760d754968f09c607f36a@changeid
|
|
There are a couple of variants of this, match them correctly
to their names and clean up a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.d03eaad5be56.I276a09f0cad364e51ed4730ca81fbe504e61f2c7@changeid
|
|
We only need a few entries, and there don't seem to be any
such devices actually limited to 160 MHz.
Also add PCI IDs for the new Killer device on LNL platforms.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.ba2964bee671.If7aaaf10b236115e39b17d37296341de6c821069@changeid
|
|
Again some names don't actually exist, and we only need a
few entries to cover Ty (discrete) and AX211/AX411.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.8888f6798581.If332ebfc3b3f4a335a79ccee13e90f93b1ee4df7@changeid
|
|
This really only needs to be distinguished based on the
RF type, bandwidth limit and possibly diversity (JF1).
Some of the names that are defined don't even exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.bca83604aa92.I35301d2d8b57c072284fff7bf6682b4a9424e56c@changeid
|
|
It's OK to match with subdevice_mask as long as that doesn't
overlap the RF ID/BW limit/cores fields in that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.87cc0ad360a8.I9be361caedd7258e8e817d4100c549681396f307@changeid
|
|
We only need a few entries on top of the Killer ones.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.fa0cde465de0.I6a3f9ed9a7341e2c58c69af50a9f126992a745f2@changeid
|
|
Unify a number of Killer devices now that we no longer
need to distinguish the MAC type, and add a few more
that wouldn't have gotten the right name before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.a16b1c2740f8.I147b97ef2c8e99451806ea0e34a9eb5bff37c326@changeid
|
|
All of these should be 160 MHz, and they can be recognised
by just the subdevice ID. Unify all the Killer/JF entries.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.a93788f159ec.I114f09a0f61849ac3b75d12d7def35be842e5b7c@changeid
|
|
These should be according to their RF type, not just use
GF unconditionally. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.4dd365eb76cd.I91f368df691a3ce6c545d9cdc44676e7883efa16@changeid
|
|
Officially, the device names have dashes ("Wireless-N"),
so add them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250510214621.4f7bbd57680f.Ida19b5e696723db5839c13341d6ca7085e8c2568@changeid
|
