| Age | Commit message (Collapse) | Author |
|---|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty_port struct is part of the rpmsg_tty_port structure.
The issue is that the rpmsg_tty_port structure is freed on
rpmsg_tty_remove while it is still referenced in the tty_struct.
Its release is not predictable due to workqueues.
For instance following ftrace shows that rpmsg_tty_close is called after
rpmsg_tty_release_cport:
nr_test.sh-389 [000] ..... 212.093752: rpmsg_tty_remove <-rpmsg_dev_
remove
cat-1191 [001] ..... 212.095697: tty_release <-__fput
nr_test.sh-389 [000] ..... 212.099166: rpmsg_tty_release_cport <-rpm
sg_tty_remove
cat-1191 [001] ..... 212.115352: rpmsg_tty_close <-tty_release
cat-1191 [001] ..... 212.115371: release_tty <-tty_release_str
As consequence, the port must be free only when user has released the TTY
interface.
This path :
- Introduce the .destruct port tty ops function to release the allocated
rpmsg_tty_port structure.
- Introduce the .hangup tty ops function to call tty_port_hangup.
- Manages the tty port refcounting to trig the .destruct port ops,
- Introduces the rpmsg_tty_cleanup function to ensure that the TTY is
removed before decreasing the port refcount.
Fixes: 7c0408d80579 ("tty: add rpmsg driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220104163545.34710-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5021d709b31b8a14317998a33cbc78be0de9ab30.
The patch is still a bit buggy, and this breaks some other hardware
types. It needs to be resubmitted in a non-buggy way, and make sure the
other hardware types also continue to work properly.
Fixes: 5021d709b31b ("tty: serial: Use fifo in 8250 console driver")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/Ye/1+Z8mEzbKbrqG@linutronix.de
Link: https://lore.kernel.org/r/a1ac6254-f79e-d131-fa2a-c7ad714c6d4a@nvidia.com
Cc: Wander Lairson Costa <wander@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
CDNSP driver read not initialized cdns->otg_v0_regs
which lead to segmentation fault. Patch fixes this issue.
Fixes: 2cf2581cd229 ("usb: cdns3: add power lost support for system resume")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In uniphier_spi_remove(), there is a wrong code to get private data from
the platform device, so the driver can't be removed properly.
The driver should get spi_master from the platform device and retrieve
the private data from it.
Cc: <stable@vger.kernel.org>
Fixes: 5ba155a4d4cc ("spi: add SPI controller driver for UniPhier SoC")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1640148492-32178-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a build error observed with ARCH=arm DEFCONFIG=allmodconfig build.
drivers/usb/gadget/udc/at91_udc.h:174:42: error: format '%d' expects argument of type 'int', but argument 3 has type 'struct gpio_desc *' [-Werror=format=]
Fixes: 4a555f2b8d31 ("usb: gadget: at91_udc: Convert to GPIO descriptors")
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220119020849.25732-1-miles.chen@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Crashed at i.mx8qm platform when suspend if enable remote wakeup
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 244 Comm: kworker/u12:6 Not tainted 5.15.5-dirty #12
Hardware name: Freescale i.MX8QM MEK (DT)
Workqueue: events_unbound async_run_entry_fn
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xhci_disable_hub_port_wake.isra.62+0x60/0xf8
lr : xhci_disable_hub_port_wake.isra.62+0x34/0xf8
sp : ffff80001394bbf0
x29: ffff80001394bbf0 x28: 0000000000000000 x27: ffff00081193b578
x26: ffff00081193b570 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00081193a29c x22: 0000000000020001 x21: 0000000000000001
x20: 0000000000000000 x19: ffff800014e90490 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000002 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000960 x9 : ffff80001394baa0
x8 : ffff0008145d1780 x7 : ffff0008f95b8e80 x6 : 000000001853b453
x5 : 0000000000000496 x4 : 0000000000000000 x3 : ffff00081193a29c
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff000814591620
Call trace:
xhci_disable_hub_port_wake.isra.62+0x60/0xf8
xhci_suspend+0x58/0x510
xhci_plat_suspend+0x50/0x78
platform_pm_suspend+0x2c/0x78
dpm_run_callback.isra.25+0x50/0xe8
__device_suspend+0x108/0x3c0
The basic flow:
1. run time suspend call xhci_suspend, xhci parent devices gate the clock.
2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend
3. xhci_suspend call xhci_disable_hub_port_wake, which access register,
but clock already gated by run time suspend.
This problem was hidden by power domain driver, which call run time resume before it.
But the below commit remove it and make this issue happen.
commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()")
This patch call run time resume before suspend to make sure clock is on
before access register.
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Testeb-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A recent bug report outlined that the way GICv4.1 is handled across
kexec is pretty bad. We can end-up in a situation where ITSs share
memory (this is the case when SVPET==1) and reprogram the base
registers, creating a situation where ITSs that are part of a given
affinity group see different pointers. Which is illegal. Boo.
In order to restore some sanity, reset the BASERn registers to 0
*before* probing any ITS. Although this isn't optimised at all,
this is only a once-per-boot cost, which shouldn't show up on
anyone's radar.
Cc: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211216190315.GA14220@lpieralisi
Link: https://lore.kernel.org/r/20220124133809.1291195-1-maz@kernel.org
|
|
This reverts commit 9bb7b689274b67ecb3641e399e76f84adc627df1.
This caused a regression reported to Red Hat.
Fixes: 9bb7b689274b ("drm/ast: Support 1600x900 with 108MHz PCLK")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120040527.552068-1-airlied@gmail.com
|
|
If gpmi_nfc_apply_timings() fails, the PM runtime usage counter must be
dropped.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: f53d4c109a66 ("mtd: rawnand: gpmi: Add ERR007117 protection for nfc_apply_timings")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220125081619.6286-1-ceggers@arri.de
|
|
Backmerging drm/drm-fixes into drm-misc-fixes for v5.17-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
Function pcie_rmw() is not being used at all and can be deleted. Hence get
rid of it, which fixes this warning:
drivers/pci/controller/pcie-mt7621.c:112:20: warning: unused function 'pcie_rmw' [-Wunused-function]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-3-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/all/202201241754.igtHzgHv-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We have stubs for most OF interfaces even when CONFIG_OF is not set, so we
allow building of pcie-mt7621.c in that case for compile testing.
When CONFIG_OF is not set, "of_match_ptr(mt7621_pcie_ids)" compiles to
NULL, which leaves mt7621_pcie_ids unused:
$ make W=1
drivers/pci/controller/pcie-mt7621.c:549:34: warning: unused variable 'mt7621_pcie_ids' [-Wunused-const-variable]
Drop of_match_ptr() to avoid the unused variable warning.
[bhelgaas: commit log]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-2-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/r/202201241754.igtHzgHv-lkp@intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Unused. Convert the divisions into asserts on the divisor, to
debug why it is zero. The divide by zero is suspected of causing
kernel panics.
While I have no idea where the zero is coming from I think this
patch is a positive either way.
Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Mirrors the logic for dcn30. Cue lots of WARNs and some
kernel panics without this fix.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It calls populate_dml_pipes which uses doubles to initialize the
scale_ratio_depth params. Mirrors the dcn20 logic.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In calculate_bandwidth(), the tag free_sclk and free_yclk are reversed,
which could lead to a memory leak of yclk.
Fix this bug by changing the location of free_sclk and free_yclk.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 2be8989d0fc2 ("drm/amd/display/dc/calcs/dce_calcs: Move some large variables from the stack to the heap")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) throw an compilation error if the
udelay is too long. In general udelays of longer than 2000us are
not recommended on any architecture. Switch to msleep in these
cases.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) have relatively low udelay limits.
On most architectures, anything longer than 2000us is not recommended.
Change the check to align with other similar checks in DC.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Older radeon boards (r2xx-r5xx) had secondary PCI functions
which we solely there for supporting multi-head on OSs with
special requirements. Add them to the unsupported list
as well so we don't attempt to bind to them. The driver
would fail to bind to them anyway, but this does so
in a cleaner way that should not confuse the user.
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
FIFO reset is only necessary for fast boot sequence, where otg is disabled
and dig fe is enabled when changing dispclk. Fast boot is only enabled
on embedded displays.
[How]
Change FIFO reset condition to "embedded display only".
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN301 has seamless boot enabled. With MPC split enabled
at the same time, system will hang.
[How]
Revert MPC split policy back to "MPC_SPLIT_AVOID". Since we have
ODM combine enabled on DCN301, pipe split is not necessary here.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
v2:
Don't drop is_blanked logic
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: torvalds@linux-foundation.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need to flush TLBs before releasing backing store otherwise userspace
is able to encounter stale entries if a) it is not declaring access to
certain buffers and b) it races with the backing store release from a
such undeclared execution already executing on the GPU in parallel.
The approach taken is to mark any buffer objects which were ever bound
to the GPU and to trigger a serialized TLB flush when their backing
store is released.
Alternatively the flushing could be done on VMA unbind, at which point
we would be able to ascertain whether there is potential a parallel GPU
execution (which could race), but essentially it boils down to paying
the cost of TLB flushes potentially needlessly at VMA unbind time (when
the backing store is not known to be going away so not needed for
safety), versus potentially needlessly at backing store relase time
(since we at that point cannot tell whether there is anything executing
on the GPU which uses that object).
Thereforce simplicity of implementation has been chosen for now with
scope to benchmark and refine later as required.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Sushma Venkatesh Reddy <sushma.venkatesh.reddy@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.
Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V causing VSAFE0V to be triggered. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: 28b43d3d746b8 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes NULL pointer dereference that happens if
component master is registered with empty component match
list.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that creates the links to the USB ports attached to
a connector inside the system assumed that the ACPI nodes
(fwnodes) always exist for the connectors, but it can not do
that.
There is no guarantee that every USB Type-C connector has
ACPI device node representing it in the ACPI tables, and
even if there are the nodes in the ACPI tables, the _STA
method in those nodes may still return 0 (which means the
device does not exist from ACPI PoW).
This fixes NULL pointer dereference that happens if the
nodes are missing.
Fixes: 730b49aac426 ("usb: typec: port-mapper: Convert to the component framework")
Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Tested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220124090228.41396-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.
Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.
Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Copy scattered mac address octets into an array then eth_hw_addr_set().
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: https://lore.kernel.org/r/20220125144007.64407-1-tsbogend@alpha.franken.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
With system suspend using pm_runtime_force_suspend() we can't rely on
the pm_runtime_get_if_in_use() trick to deal with devfreq callbacks
after (or racing with) suspend. So flush any pending idle or boost
work in the suspend path.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220108180913.814448-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
System suspend uses pm_runtime_force_suspend(), which cheekily bypasses
the runpm reference counts. This doesn't actually work so well when the
GPU is active. So add a reasonable delay waiting for the GPU to become
idle.
Alternatively we could just return -EBUSY in this case, but that has the
disadvantage of causing system suspend to fail.
v2: s/ret/remaining [sboyd], and switch to using active_submits count
to ensure we aren't racing with submit cleanup (and devfreq idle
work getting scheduled, etc)
v3: fix inverted logic
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220108180913.814448-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
If registering the platform driver fails, the function must not return
without undoing the spi driver registration first.
Fixes: c296d5f9957c ("staging: fbtft: core support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220118181338.207943-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In service_callback path RCU dereferenced pointer struct vchiq_service
need to be accessed inside rcu read-critical section.
Also userdata/user_service part of vchiq_service is accessed around
different synchronization mechanism, getting an extra reference to a
pointer keeps sematics simpler and avoids prolonged graceperiod.
Accessing vchiq_service with rcu_read_[lock/unlock] fixes below issue.
[ 32.201659] =============================
[ 32.201664] WARNING: suspicious RCU usage
[ 32.201670] 5.15.11-rt24-v8+ #3 Not tainted
[ 32.201680] -----------------------------
[ 32.201685] drivers/staging/vc04_services/interface/vchiq_arm/vchiq_core.h:529 suspicious rcu_dereference_check() usage!
[ 32.201695]
[ 32.201695] other info that might help us debug this:
[ 32.201695]
[ 32.201700]
[ 32.201700] rcu_scheduler_active = 2, debug_locks = 1
[ 32.201708] no locks held by vchiq-slot/0/98.
[ 32.201715]
[ 32.201715] stack backtrace:
[ 32.201723] CPU: 1 PID: 98 Comm: vchiq-slot/0 Not tainted 5.15.11-rt24-v8+ #3
[ 32.201733] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT)
[ 32.201739] Call trace:
[ 32.201742] dump_backtrace+0x0/0x1b8
[ 32.201772] show_stack+0x20/0x30
[ 32.201784] dump_stack_lvl+0x8c/0xb8
[ 32.201799] dump_stack+0x18/0x34
[ 32.201808] lockdep_rcu_suspicious+0xe4/0xf8
[ 32.201817] service_callback+0x124/0x400
[ 32.201830] slot_handler_func+0xf60/0x1e20
[ 32.201839] kthread+0x19c/0x1a8
[ 32.201849] ret_from_fork+0x10/0x20
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Padmanabha Srinivasaiah <treasure4paddy@gmail.com>
Link: https://lore.kernel.org/r/20211231195406.5479-1-treasure4paddy@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since some interrupt states may be cleared by hardware, the driver
may receive an empty interrupt. Currently, the VF driver directly
disables the vector0 interrupt in this case. As a result, the VF
is unavailable. Therefore, the vector0 interrupt should be enabled
in this case.
Fixes: b90fcc5bd904 ("net: hns3: add reset handling for VF when doing Core/Global/IMP reset")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes made netdev->dev_addr const, and it's passed
directly to mpc52xx_fec_set_paddr().
Similar problem exists on the probe patch, the driver needs
to call eth_hw_addr_set().
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cpsw driver didn't properly initialise the struct page_pool_params
before calling page_pool_create(), which leads to crashes after the struct
has been expanded with new parameters.
The second Fixes tag below is where the buggy code was introduced, but
because the code was moved around this patch will only apply on top of the
commit in the first Fixes tag.
Fixes: c5013ac1dd0e ("net: ethernet: ti: cpsw: move set of common functions in cpsw_priv")
Fixes: 9ed4050c0d75 ("net: ethernet: ti: cpsw: add XDP support")
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Tested-by: Colin Foster <colin.foster@in-advantage.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
