| Age | Commit message (Collapse) | Author |
|---|
|
XFRM stack doesn't prevent from users to configure replay window
in TX side and strongswan sets replay_window to be 1. It causes
to failures in validation logic when trying to offload the SA.
Replay window is not relevant in TX side and should be ignored.
Fixes: cded6d80129b ("net/mlx5e: Store replay window in XFRM attributes")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
All ConnectX devices have software parsing capability enabled, but it is
more correct to set allow_swp only if capability exists, which for IPsec
means that crypto offload is supported.
Fixes: 2451da081a34 ("net/mlx5: Unify device IPsec capabilities check")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 devices have specific constants for choosing the CQ period mode. These
constants do not have to match the constants used by the kernel software
API for DIM period mode selection.
Fixes: cdd04f4d4d71 ("net/mlx5: Add support to create SQ and CQ for ASO")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Go-To-Vport action on RX is not allowed when the vport is uplink.
In such case, the packet should be dropped.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When FW provides ICM addresses for drop RX/TX, the provided capability
is 64 bits that contain its GVMI as well as the ICM address itself.
In case of TX DROP this GVMI is different from the GVMI that the
domain is operating on.
This patch fixes the action to use these GVMI IDs, as provided by FW.
Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
To enable multicast packets which are offloaded in bridge multicast
offload mode to be sent also to uplink, FTE bit uplink_hairpin_en should
be set. Add this bit to FTE for the bridge multicast offload rules.
Fixes: 18c2916cee12 ("net/mlx5: Bridge, snoop igmp/mld packets")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The below WARN [1] is reported once a callback command failed.
As a callback runs under an interrupt context, needs to use the IRQ
save/restore variant.
[1]
DEBUG_LOCKS_WARN_ON(lockdep_hardirq_context())
WARNING: CPU: 15 PID: 0 at kernel/locking/lockdep.c:4353
lockdep_hardirqs_on_prepare+0x11b/0x180
Modules linked in: vhost_net vhost tap mlx5_vfio_pci
vfio_pci vfio_pci_core vfio_iommu_type1 vfio mlx5_vdpa vringh
vhost_iotlb vdpa nfnetlink_cttimeout openvswitch nsh ip6table_mangle
ip6table_nat ip6table_filter ip6_tables iptable_mangle
xt_conntrackxt_MASQUERADE nf_conntrack_netlink nfnetlink
xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5
auth_rpcgss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi
scsi_transport_iscsi rdma_cm iw_cm ib_umad ib_ipoib ib_cm
mlx5_ib ib_uverbs ib_core fuse mlx5_core
CPU: 15 PID: 0 Comm: swapper/15 Tainted: G W 6.7.0-rc4+ #1587
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:lockdep_hardirqs_on_prepare+0x11b/0x180
Code: 00 5b c3 c3 e8 e6 0d 58 00 85 c0 74 d6 8b 15 f0 c3
76 01 85 d2 75 cc 48 c7 c6 04 a5 3b 82 48 c7 c7 f1
e9 39 82 e8 95 12 f9 ff <0f> 0b 5b c3 e8 bc 0d 58 00
85 c0 74 ac 8b 3d c6 c3 76 01 85 ff 75
RSP: 0018:ffffc900003ecd18 EFLAGS: 00010086
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000027
RDX: 0000000000000000 RSI: ffff88885fbdb880 RDI: ffff88885fbdb888
RBP: 00000000ffffff87 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 284e4f5f4e524157 R12: 00000000002c9aa1
R13: ffff88810aace980 R14: ffff88810aace9b8 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff88885fbc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f731436f4c8 CR3: 000000010aae6001 CR4: 0000000000372eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? __warn+0x81/0x170
? lockdep_hardirqs_on_prepare+0x11b/0x180
? report_bug+0xf8/0x1c0
? handle_bug+0x3f/0x70
? exc_invalid_op+0x13/0x60
? asm_exc_invalid_op+0x16/0x20
? lockdep_hardirqs_on_prepare+0x11b/0x180
? lockdep_hardirqs_on_prepare+0x11b/0x180
trace_hardirqs_on+0x4a/0xa0
raw_spin_unlock_irq+0x24/0x30
cmd_status_err+0xc0/0x1a0 [mlx5_core]
cmd_status_err+0x1a0/0x1a0 [mlx5_core]
mlx5_cmd_exec_cb_handler+0x24/0x40 [mlx5_core]
mlx5_cmd_comp_handler+0x129/0x4b0 [mlx5_core]
cmd_comp_notifier+0x1a/0x20 [mlx5_core]
notifier_call_chain+0x3e/0xe0
atomic_notifier_call_chain+0x5f/0x130
mlx5_eq_async_int+0xe7/0x200 [mlx5_core]
notifier_call_chain+0x3e/0xe0
atomic_notifier_call_chain+0x5f/0x130
irq_int_handler+0x11/0x20 [mlx5_core]
__handle_irq_event_percpu+0x99/0x220
? tick_irq_enter+0x5d/0x80
handle_irq_event_percpu+0xf/0x40
handle_irq_event+0x3a/0x60
handle_edge_irq+0xa2/0x1c0
__common_interrupt+0x55/0x140
common_interrupt+0x7d/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0x13/0x20
Code: c0 08 00 00 00 4d 29 c8 4c 01 c7 4c 29 c2 e9 72 ff
ff ff cc cc cc cc 8b 05 ea 08 25 01 85 c0 7e 07 0f 00 2d 7f b0 26 00 fb
f4 <fa> c3 90 66 2e 0f 1f 84 00 00 00 00 00 65 48 8b 04 25 80 d0 02 00
RSP: 0018:ffffc9000010fec8 EFLAGS: 00000242
RAX: 0000000000000001 RBX: 000000000000000f RCX: 4000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffff811c410c
RBP: ffffffff829478c0 R08: 0000000000000001 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
? do_idle+0x1ec/0x210
default_idle_call+0x6c/0x90
do_idle+0x1ec/0x210
cpu_startup_entry+0x26/0x30
start_secondary+0x11b/0x150
secondary_startup_64_no_verify+0x165/0x16b
</TASK>
irq event stamp: 833284
hardirqs last enabled at (833283): [<ffffffff811c410c>]
do_idle+0x1ec/0x210
hardirqs last disabled at (833284): [<ffffffff81daf9ef>]
common_interrupt+0xf/0xa0
softirqs last enabled at (833224): [<ffffffff81dc199f>]
__do_softirq+0x2bf/0x40e
softirqs last disabled at (833177): [<ffffffff81178ddf>]
irq_exit_rcu+0x7f/0xa0
Fixes: 34f46ae0d4b3 ("net/mlx5: Add command failures data to debugfs")
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited change refactored mlx5e_tc_del_fdb_peer_flow() to only clear DUP
flag when list of peer flows has become empty. However, if any concurrent
user holds a reference to a peer flow (for example, the neighbor update
workqueue task is updating peer flow's parent encap entry concurrently),
then the flow will not be removed from the peer list and, consecutively,
DUP flag will remain set. Since mlx5e_tc_del_fdb_peers_flow() calls
mlx5e_tc_del_fdb_peer_flow() for every possible peer index the algorithm
will try to remove the flow from eswitch instances that it has never peered
with causing either NULL pointer dereference when trying to remove the flow
peer list head of peer_index that was never initialized or a warning if the
list debug config is enabled[0].
Fix the issue by always removing the peer flow from the list even when not
releasing the last reference to it.
[0]:
[ 3102.985806] ------------[ cut here ]------------
[ 3102.986223] list_del corruption, ffff888139110698->next is NULL
[ 3102.986757] WARNING: CPU: 2 PID: 22109 at lib/list_debug.c:53 __list_del_entry_valid_or_report+0x4f/0xc0
[ 3102.987561] Modules linked in: act_ct nf_flow_table bonding act_tunnel_key act_mirred act_skbedit vxlan cls_matchall nfnetlink_cttimeout act_gact cls_flower sch_ingress mlx5_vdpa vringh vhost_iotlb vdpa openvswitch nsh xt_MASQUERADE nf_conntrack_netlink nfnetlink iptable_nat xt_addrtype xt_conntrack nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcg
ss oid_registry overlay rpcrdma rdma_ucm ib_iser libiscsi scsi_transport_iscsi ib_umad rdma_cm ib_ipoib iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core [last unloaded: bonding]
[ 3102.991113] CPU: 2 PID: 22109 Comm: revalidator28 Not tainted 6.6.0-rc6+ #3
[ 3102.991695] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
[ 3102.992605] RIP: 0010:__list_del_entry_valid_or_report+0x4f/0xc0
[ 3102.993122] Code: 39 c2 74 56 48 8b 32 48 39 fe 75 62 48 8b 51 08 48 39 f2 75 73 b8 01 00 00 00 c3 48 89 fe 48 c7 c7 48 fd 0a 82 e8 41 0b ad ff <0f> 0b 31 c0 c3 48 89 fe 48 c7 c7 70 fd 0a 82 e8 2d 0b ad ff 0f 0b
[ 3102.994615] RSP: 0018:ffff8881383e7710 EFLAGS: 00010286
[ 3102.995078] RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
[ 3102.995670] RDX: 0000000000000001 RSI: ffff88885f89b640 RDI: ffff88885f89b640
[ 3102.997188] DEL flow 00000000be367878 on port 0
[ 3102.998594] RBP: dead000000000122 R08: 0000000000000000 R09: c0000000ffffdfff
[ 3102.999604] R10: 0000000000000008 R11: ffff8881383e7598 R12: dead000000000100
[ 3103.000198] R13: 0000000000000002 R14: ffff888139110000 R15: ffff888101901240
[ 3103.000790] FS: 00007f424cde4700(0000) GS:ffff88885f880000(0000) knlGS:0000000000000000
[ 3103.001486] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 3103.001986] CR2: 00007fd42e8dcb70 CR3: 000000011e68a003 CR4: 0000000000370ea0
[ 3103.002596] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 3103.003190] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 3103.003787] Call Trace:
[ 3103.004055] <TASK>
[ 3103.004297] ? __warn+0x7d/0x130
[ 3103.004623] ? __list_del_entry_valid_or_report+0x4f/0xc0
[ 3103.005094] ? report_bug+0xf1/0x1c0
[ 3103.005439] ? console_unlock+0x4a/0xd0
[ 3103.005806] ? handle_bug+0x3f/0x70
[ 3103.006149] ? exc_invalid_op+0x13/0x60
[ 3103.006531] ? asm_exc_invalid_op+0x16/0x20
[ 3103.007430] ? __list_del_entry_valid_or_report+0x4f/0xc0
[ 3103.007910] mlx5e_tc_del_fdb_peers_flow+0xcf/0x240 [mlx5_core]
[ 3103.008463] mlx5e_tc_del_flow+0x46/0x270 [mlx5_core]
[ 3103.008944] mlx5e_flow_put+0x26/0x50 [mlx5_core]
[ 3103.009401] mlx5e_delete_flower+0x25f/0x380 [mlx5_core]
[ 3103.009901] tc_setup_cb_destroy+0xab/0x180
[ 3103.010292] fl_hw_destroy_filter+0x99/0xc0 [cls_flower]
[ 3103.010779] __fl_delete+0x2d4/0x2f0 [cls_flower]
[ 3103.011207] fl_delete+0x36/0x80 [cls_flower]
[ 3103.011614] tc_del_tfilter+0x56f/0x750
[ 3103.011982] rtnetlink_rcv_msg+0xff/0x3a0
[ 3103.012362] ? netlink_ack+0x1c7/0x4e0
[ 3103.012719] ? rtnl_calcit.isra.44+0x130/0x130
[ 3103.013134] netlink_rcv_skb+0x54/0x100
[ 3103.013533] netlink_unicast+0x1ca/0x2b0
[ 3103.013902] netlink_sendmsg+0x361/0x4d0
[ 3103.014269] __sock_sendmsg+0x38/0x60
[ 3103.014643] ____sys_sendmsg+0x1f2/0x200
[ 3103.015018] ? copy_msghdr_from_user+0x72/0xa0
[ 3103.015265] ___sys_sendmsg+0x87/0xd0
[ 3103.016608] ? copy_msghdr_from_user+0x72/0xa0
[ 3103.017014] ? ___sys_recvmsg+0x9b/0xd0
[ 3103.017381] ? ttwu_do_activate.isra.137+0x58/0x180
[ 3103.017821] ? wake_up_q+0x49/0x90
[ 3103.018157] ? futex_wake+0x137/0x160
[ 3103.018521] ? __sys_sendmsg+0x51/0x90
[ 3103.018882] __sys_sendmsg+0x51/0x90
[ 3103.019230] ? exit_to_user_mode_prepare+0x56/0x130
[ 3103.019670] do_syscall_64+0x3c/0x80
[ 3103.020017] entry_SYSCALL_64_after_hwframe+0x46/0xb0
[ 3103.020469] RIP: 0033:0x7f4254811ef4
[ 3103.020816] Code: 89 f3 48 83 ec 10 48 89 7c 24 08 48 89 14 24 e8 42 eb ff ff 48 8b 14 24 41 89 c0 48 89 de 48 8b 7c 24 08 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 30 44 89 c7 48 89 04 24 e8 78 eb ff ff 48 8b
[ 3103.022290] RSP: 002b:00007f424cdd9480 EFLAGS: 00000293 ORIG_RAX: 000000000000002e
[ 3103.022970] RAX: ffffffffffffffda RBX: 00007f424cdd9510 RCX: 00007f4254811ef4
[ 3103.023564] RDX: 0000000000000000 RSI: 00007f424cdd9510 RDI: 0000000000000012
[ 3103.024158] RBP: 00007f424cdda238 R08: 0000000000000000 R09: 00007f41d801a4b0
[ 3103.024748] R10: 0000000000000000 R11: 0000000000000293 R12: 0000000000000001
[ 3103.025341] R13: 00007f424cdd9510 R14: 00007f424cdda240 R15: 00007f424cdd99a0
[ 3103.025931] </TASK>
[ 3103.026182] ---[ end trace 0000000000000000 ]---
[ 3103.027033] ------------[ cut here ]------------
Fixes: 9be6c21fdcf8 ("net/mlx5e: Handle offloads flows per peer")
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The processing of traffic in hairpin queues occurs in HW/FW and does not
involve the cpus, hence the upper bound on max num channels does not
apply to them. Using this bound for the hairpin RQT max_table_size is
wrong. It could be too small, and cause the error below [1]. As the
RQT size provided on init does not get modified later, use the same
value for both actual and max table sizes.
[1]
mlx5_core 0000:08:00.1: mlx5_cmd_out_err:805:(pid 1200): CREATE_RQT(0x916) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x538faf), err(-22)
Fixes: 74a8dadac17e ("net/mlx5e: Preparations for supporting larger number of channels")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Indirection (*) is of lower precedence than postfix increment (++). Logic
in napi_poll context would cause an out-of-bound read by first increment
the pointer address by byte address space and then dereference the value.
Rather, the intended logic was to dereference first and then increment the
underlying value.
Fixes: 92214be5979c ("net/mlx5e: Update doorbell for port timestamping CQ before the software counter")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The sd_group field moved in the HW spec from the MPIR register
to the vport context.
Align the query accordingly.
Fixes: f5e956329960 ("net/mlx5: Expose Management PCIe Index Register (MPIR)")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit moved the code of mlx5e_create_tises() and changed the
loop to create TISes over MLX5_MAX_PORTS constant value, instead of
getting the correct lag ports supported by the device, which can cause
FW errors on devices with less than MLX5_MAX_PORTS ports.
Change that back to mlx5e_get_num_lag_ports(mdev).
Also IPoIB interfaces create there own TISes, they don't use the eth
TISes, pass a flag to indicate that.
This fixes the following errors that might appear in kernel log:
mlx5_cmd_out_err:808:(pid 650): CREATE_TIS(0x912) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x595b5d), err(-22)
mlx5e_create_mdev_resources:174:(pid 650): alloc tises failed, -22
Fixes: b25bd37c859f ("net/mlx5: Move TISes from priv to mdev HW resources")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The ASM1166 SATA host controller always reports wrongly,
that it has 32 ports. But in reality, it only has six ports.
This seems to be a hardware issue, as all tested ASM1166
SATA host controllers reports such high count of ports.
Example output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0xffffff3f impl SATA mode.
By adjusting the port_map, the count is limited to six ports.
New output: ahci 0000:09:00.0: AHCI 0001.0301
32 slots 32 ports 6 Gbps 0x3f impl SATA mode.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=211873
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218346
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Current code in netvsc_drv_init() incorrectly assumes that PAGE_SIZE
is 4 Kbytes, which is wrong on ARM64 with 16K or 64K page size. As a
result, the default VMBus ring buffer size on ARM64 with 64K page size
is 8 Mbytes instead of the expected 512 Kbytes. While this doesn't break
anything, a typical VM with 8 vCPUs and 8 netvsc channels wastes 120
Mbytes (8 channels * 2 ring buffers/channel * 7.5 Mbytes/ring buffer).
Unfortunately, the module parameter specifying the ring buffer size
is in units of 4 Kbyte pages. Ideally, it should be in units that
are independent of PAGE_SIZE, but backwards compatibility prevents
changing that now.
Fix this by having netvsc_drv_init() hardcode 4096 instead of using
PAGE_SIZE when calculating the ring buffer size in bytes. Also
use the VMBUS_RING_SIZE macro to ensure proper alignment when running
with page size larger than 4K.
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 7aff79e297ee ("Drivers: hv: Enable Hyper-V code to be built on ARM64")
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20240122162028.348885-1-mhklinux@outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This reverts commit b34ab3527b9622ca4910df24ff5beed5aa66c6b5.
Using skb_ensure_writable_head_tail without a call to skb_unshare causes
the MACsec stack to operate on the original skb rather than a copy in the
macsec_encrypt path. This causes the buffer to be exceeded in space, and
leads to warnings generated by skb_put operations. Opting to revert this
change since skb_copy_expand is more efficient than
skb_ensure_writable_head_tail followed by a call to skb_unshare.
Log:
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:2464!
invalid opcode: 0000 [#1] SMP KASAN
CPU: 21 PID: 61997 Comm: iperf3 Not tainted 6.7.0-rc8_for_upstream_debug_2024_01_07_17_05 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:skb_put+0x113/0x190
Code: 03 0f b6 14 02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 04 84 d2 75 70 3b 9d bc 00 00 00 77 0e 48 83 c4 08 4c 89 e8 5b 5d 41 5d c3 <0f> 0b 4c 8b 6c 24 20 89 74 24 04 e8 6d b7 f0 fe 8b 74 24 04 48 c7
RSP: 0018:ffff8882694e7278 EFLAGS: 00010202
RAX: 0000000000000025 RBX: 0000000000000100 RCX: 0000000000000001
RDX: 0000000000000000 RSI: 0000000000000010 RDI: ffff88816ae0bad4
RBP: ffff88816ae0ba60 R08: 0000000000000004 R09: 0000000000000004
R10: 0000000000000001 R11: 0000000000000001 R12: ffff88811ba5abfa
R13: ffff8882bdecc100 R14: ffff88816ae0ba60 R15: ffff8882bdecc0ae
FS: 00007fe54df02740(0000) GS:ffff88881f080000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fe54d92e320 CR3: 000000010a345003 CR4: 0000000000370eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
? die+0x33/0x90
? skb_put+0x113/0x190
? do_trap+0x1b4/0x3b0
? skb_put+0x113/0x190
? do_error_trap+0xb6/0x180
? skb_put+0x113/0x190
? handle_invalid_op+0x2c/0x30
? skb_put+0x113/0x190
? exc_invalid_op+0x2b/0x40
? asm_exc_invalid_op+0x16/0x20
? skb_put+0x113/0x190
? macsec_start_xmit+0x4e9/0x21d0
macsec_start_xmit+0x830/0x21d0
? get_txsa_from_nl+0x400/0x400
? lock_downgrade+0x690/0x690
? dev_queue_xmit_nit+0x78b/0xae0
dev_hard_start_xmit+0x151/0x560
__dev_queue_xmit+0x1580/0x28f0
? check_chain_key+0x1c5/0x490
? netdev_core_pick_tx+0x2d0/0x2d0
? __ip_queue_xmit+0x798/0x1e00
? lock_downgrade+0x690/0x690
? mark_held_locks+0x9f/0xe0
ip_finish_output2+0x11e4/0x2050
? ip_mc_finish_output+0x520/0x520
? ip_fragment.constprop.0+0x230/0x230
? __ip_queue_xmit+0x798/0x1e00
__ip_queue_xmit+0x798/0x1e00
? __skb_clone+0x57a/0x760
__tcp_transmit_skb+0x169d/0x3490
? lock_downgrade+0x690/0x690
? __tcp_select_window+0x1320/0x1320
? mark_held_locks+0x9f/0xe0
? lockdep_hardirqs_on_prepare+0x286/0x400
? tcp_small_queue_check.isra.0+0x120/0x3d0
tcp_write_xmit+0x12b6/0x7100
? skb_page_frag_refill+0x1e8/0x460
__tcp_push_pending_frames+0x92/0x320
tcp_sendmsg_locked+0x1ed4/0x3190
? tcp_sendmsg_fastopen+0x650/0x650
? tcp_sendmsg+0x1a/0x40
? mark_held_locks+0x9f/0xe0
? lockdep_hardirqs_on_prepare+0x286/0x400
tcp_sendmsg+0x28/0x40
? inet_send_prepare+0x1b0/0x1b0
__sock_sendmsg+0xc5/0x190
sock_write_iter+0x222/0x380
? __sock_sendmsg+0x190/0x190
? kfree+0x96/0x130
vfs_write+0x842/0xbd0
? kernel_write+0x530/0x530
? __fget_light+0x51/0x220
? __fget_light+0x51/0x220
ksys_write+0x172/0x1d0
? update_socket_protocol+0x10/0x10
? __x64_sys_read+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x286/0x400
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x46/0x4e
RIP: 0033:0x7fe54d9018b7
Code: 0f 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
RSP: 002b:00007ffdbd4191d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000025 RCX: 00007fe54d9018b7
RDX: 0000000000000025 RSI: 0000000000d9859c RDI: 0000000000000004
RBP: 0000000000d9859c R08: 0000000000000004 R09: 0000000000000000
R10: 00007fe54d80afe0 R11: 0000000000000246 R12: 0000000000000004
R13: 0000000000000025 R14: 00007fe54e00ec00 R15: 0000000000d982a0
</TASK>
Modules linked in: 8021q garp mrp iptable_raw bonding vfio_pci rdma_ucm ib_umad mlx5_vfio_pci mlx5_ib vfio_pci_core vfio_iommu_type1 ib_uverbs vfio mlx5_core ip_gre nf_tables ipip tunnel4 ib_ipoib ip6_gre gre ip6_tunnel tunnel6 geneve openvswitch nsh xt_conntrack xt_MASQUERADE nf_conntrack_netlink nfnetlink xt_addrtype iptable_nat nf_nat br_netfilter rpcsec_gss_krb5 auth_rpcgss oid_registry overlay rpcrdma ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_cm ib_core zram zsmalloc fuse [last unloaded: ib_uverbs]
---[ end trace 0000000000000000 ]---
Cc: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Link: https://lore.kernel.org/r/20240118191811.50271-1-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Kalle Valo says:
====================
wireless fixes for v6.8-rc2
The most visible fix here is the ath11k crash fix which was introduced
in v6.7. We also have a fix for iwlwifi memory corruption and few
smaller fixes in the stack.
* tag 'wireless-2024-01-22' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: fix race condition on enabling fast-xmit
wifi: iwlwifi: fix a memory corruption
wifi: mac80211: fix potential sta-link leak
wifi: cfg80211/mac80211: remove dependency on non-existing option
wifi: cfg80211: fix missing interfaces when dumping
wifi: ath11k: rely on mac80211 debugfs handling for vif
wifi: p54: fix GCC format truncation warning with wiphy->fw_version
====================
Link: https://lore.kernel.org/r/20240122153434.E0254C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Return IRQ_NONE from the interrupt handler when no interrupt was
detected. Because an empty interrupt will cause a null pointer error:
Unable to handle kernel NULL pointer dereference at virtual
address 0000000000000008
Call trace:
complete+0x54/0x100
hisi_sfc_v3xx_isr+0x2c/0x40 [spi_hisi_sfc_v3xx]
__handle_irq_event_percpu+0x64/0x1e0
handle_irq_event+0x7c/0x1cc
Signed-off-by: Devyn Liu <liudingyuan@huawei.com>
Link: https://msgid.link/r/20240123071149.917678-1-liudingyuan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the existing implementation, when executing interleaved write and read
operations in the ISR for a transfer length greater than the FIFO size,
the TXFIFO write precedes the RXFIFO read. Consequently, the initially
received data in the RXFIFO is pushed out and lost, leading to a failure
in data integrity. To address this issue, reverse the order of interleaved
operations and conduct the RXFIFO read followed by the TXFIFO write.
Fixes: 6afe2ae8dc48 ("spi: spi-cadence: Interleave write of TX and read of RX FIFO")
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://msgid.link/r/20231218090652.18403-1-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If dma_request_chan() fails, no error is shown nor any information is
shown in /sys/kernel/debug/devices_deferred if -EPROBE_DEFER is returned.
Use dev_err_probe to fix both problems.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://msgid.link/r/20240110085403.457089-1-alexander.stein@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SFDP read shall use the mspi reads when using the bcm_qspi_exec_mem_op()
call. This fixes SFDP parameter page read failures seen with parts that
now use SFDP protocol to read the basic flash parameter table.
Fixes: 5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kamal.dasu@broadcom.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://msgid.link/r/20240109210033.43249-1-kamal.dasu@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid a kernel crash in stifb by providing the correct pointer to the fb_info
struct. Prior to commit e2e0b838a184 ("video/sticore: Remove info field from
STI struct") the fb_info struct was at the beginning of the fb struct.
Fixes: e2e0b838a184 ("video/sticore: Remove info field from STI struct")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
|
|
The QXL driver doesn't use any device for DMA mappings or allocations so
dev_to_node() will panic inside ttm_device_init() on NUMA systems:
general protection fault, probably for non-canonical address 0xdffffc000000007a: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x00000000000003d0-0x00000000000003d7]
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.7.0+ #9
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:ttm_device_init+0x10e/0x340
Call Trace:
qxl_ttm_init+0xaa/0x310
qxl_device_init+0x1071/0x2000
qxl_pci_probe+0x167/0x3f0
local_pci_probe+0xe1/0x1b0
pci_device_probe+0x29d/0x790
really_probe+0x251/0x910
__driver_probe_device+0x1ea/0x390
driver_probe_device+0x4e/0x2e0
__driver_attach+0x1e3/0x600
bus_for_each_dev+0x12d/0x1c0
bus_add_driver+0x25a/0x590
driver_register+0x15c/0x4b0
qxl_pci_driver_init+0x67/0x80
do_one_initcall+0xf5/0x5d0
kernel_init_freeable+0x637/0xb10
kernel_init+0x1c/0x2e0
ret_from_fork+0x48/0x80
ret_from_fork_asm+0x1b/0x30
RIP: 0010:ttm_device_init+0x10e/0x340
Fall back to NUMA_NO_NODE if there is no device for DMA.
Found by Linux Verification Center (linuxtesting.org).
Fixes: b0a7ce53d494 ("drm/ttm: Schedule delayed_delete worker closer")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If the boot logo does not fit, a message is printed, including a wrong
function name prefix. Instead of correcting the function name (or using
__func__), just use "fbcon", like is done in several other messages.
While at it, modernize the call by switching to pr_info().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Currently, both ATA_LPM_UNKNOWN (0) and ATA_LPM_MAX_POWER (1) displays
as "max_performance" in sysfs.
This is quite misleading as they are not the same.
For ATA_LPM_UNKNOWN, ata_eh_set_lpm() will not be called at all,
leaving the configuration in unknown state.
For ATA_LPM_MAX_POWER, ata_eh_set_lpm() is called, and setting the
policy to ATA_LPM_MAX_POWER.
This also matches the description of the SATA_MOBILE_LPM_POLICY Kconfig:
0 => Keep firmware settings
1 => Maximum performance
Thus, update the sysfs description for ATA_LPM_UNKNOWN to match reality.
While at it, update libata.h to mention that the ascii descriptions
are in libata-sata.c and not in libata-scsi.c.
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Scaling min/max freq values were being cached and lagging a setting
each time. Fix the ordering of the clamp call to ensure they work.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217931
Fixes: febab20caeba ("cpufreq/amd-pstate: Fix scaling_min_freq and scaling_max_freq update")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Wyes Karny <wkarny@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CXL 3.1 Section 3.1.1 states:
"A Function on a CXL device must not generate INTx messages if
that Function participates in CXL.cache protocol or CXL.mem
protocols."
The generic CXL memory driver only supports devices which use the
CXL.mem protocol. The current driver attempts to allocate MSI/MSI-X
vectors in anticipation of their need for mailbox interrupts or event
processing. However, the above requirement does not require a device to
support interrupts, only that they use MSI/MSI-X. For example, a device
may disable mailbox interrupts and either be configured for firmware
first or skip event processing and function.
Dave Larsen reported that the following Intel / Agilex card does not
support interrupts on function 0.
CXL: Intel Corporation Device 0ddb (rev 01) (prog-if 10 [CXL Memory Device (CXL 2.x)])
Rather than fail device probe if interrupts are not supported; flag that
irqs are not enabled and avoid features which require interrupts.
Emit messages appropriate for the situation to aid in debugging should
device behavior be unexpected due to a failure to allocate vectors.
Note that it is possible for a device to have host based event
processing through polling. However, the driver does not support
polling and it is not anticipated to be generally required. Leave that
functionality to a future patch if such a device comes along.
Reported-by: Dave Larsen <davelarsen58@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Fan Ni <fan.ni@samsung.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-and-tested-by: Davidlohr Bueso <dave@stgolabs.net>
Link: https://lore.kernel.org/r/20240117-dont-fail-irq-v2-1-f33f26b0e365@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen netback fix from Juergen Gross:
"Transmit requests in Xen's virtual network protocol can consist of
multiple parts. While not really useful, except for the initial part
any of them may be of zero length, i.e. carry no data at all.
Besides a certain initial portion of the to be transferred data, these
parts are directly translated into what Linux calls SKB fragments.
Such converted request parts can, when for a particular SKB they are
all of length zero, lead to a de-reference of NULL in core networking
code"
* tag 'xsa448-6.8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-netback: don't produce zero-size SKB frags
|
|
Stephen Rothwell reported htmldocs warnings when merging drm-intel
tree:
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5484: ERROR: Unexpected indentation.
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5488: WARNING: Block quote ends without a blank line; unexpected unindent.
Separate @failing_port return value list by surrounding it with a
blank line to fix above warnings.
Fixes: 1cd0a5ea427931 ("drm/dp_mst: Factor out a helper to check the atomic state of a topology manager")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20231114141715.6f435118@canb.auug.org.au/
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114081033.27343-1-bagasdotme@gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Similar to commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"). Add a mutex to ensure that aux transfer
won't race with atomic_disable by holding the PM reference and prevent
the bridge from suspend.
Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge
instead of idle with pm_runtime_put_sync().
Fixes: 3203e497eb76 ("drm/bridge: anx7625: Synchronously run runtime suspend.")
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org
|
|
This adds the PCI ID of the Arrow Lake and Meteor Lake-S PCH SPI serial
flash controller. This one supports all the necessary commands Linux
SPI-NOR stack requires.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240122120034.2664812-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Turns out this "SoC" side controller does not support certain commands,
such as reading chip JEDEC ID, so the controller is pretty much unusable
in Linux. We should be using the "PCH" side controller instead. For this
reason remove this PCI ID from the list.
Fixes: c2912d42e86e ("spi: intel-pci: Add support for Meteor Lake-S SPI serial flash")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://msgid.link/r/20240122120034.2664812-2-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On systems using HWP, if a given frequency is equal to the maximum turbo
frequency or the maximum non-turbo frequency, the HWP performance level
corresponding to it is already known and can be used directly without
any computation.
Accordingly, adjust the code to use the known HWP performance levels in
the cases mentioned above.
This also helps to avoid limiting CPU capacity artificially in some
cases when the BIOS produces the HWP_CAP numbers using a different
E-core-to-P-core performance scaling factor than expected by the kernel.
Fixes: f5c8cf2a4992 ("cpufreq: intel_pstate: hybrid: Use known scaling factor for P-cores")
Cc: 6.1+ <stable@vger.kernel.org> # 6.1+
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
IP reset has to followed by ivpu_pll_disable() to properly enter
reset state.
Fixes: 828d63042aec ("accel/ivpu: Don't enter d0i3 during FLR")
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024165353.761507-1-stanislaw.gruszka@linux.intel.com
|
|
The event selector fields for 2 counters are contained in one
32-bit register and the current logic does not account for this.
Fixes: 423c3361855c ("platform/mellanox: mlxbf-pmc: Add support for BlueField-3")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/8834cfa496c97c7c2fcebcfca5a2aa007e20ae96.1705485095.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Starting from Linux 5.16 kernel, Tx timeout mechanism was added
in the virtio_net driver which prints the "Tx timeout" warning
message when a packet stays in Tx queue for too long. Below is an
example of the reported message:
"[494105.316739] virtio_net virtio1 tmfifo_net0: TX timeout on
queue: 0, sq: output.0, vq: 0×1, name: output.0, usecs since
last trans: 3079892256".
This issue could happen when external host driver which drains the
FIFO is restared, stopped or upgraded. To avoid such confusing
"Tx timeout" messages, this commit adds logic to drop the outstanding
Tx packet if it's not able to transmit in two seconds due to Tx FIFO
full, which can be considered as congestion or out-of-resource drop.
This commit also handles the special case that the packet is half-
transmitted into the Tx FIFO. In such case, the packet is discarded
with remaining length stored in vring->rem_padding. So paddings with
zeros can be sent out when Tx space is available to maintain the
integrity of the packet format. The padded packet will be dropped on
the receiving side.
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240111173106.96958-1-limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP. This is exactly the same issue as on lan8841.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: ece19502834d ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of multiple kernel module instances using the same dpll device:
if only one registers dpll device, then only that one can register
directly connected pins with a dpll device. When unregistered parent is
responsible for determining if the muxed pin can be registered with it
or not, the drivers need to be loaded in serialized order to work
correctly - first the driver instance which registers the direct pins
needs to be loaded, then the other instances could register muxed type
pins.
Allow registration of a pin with a parent even if the parent was not
yet registered, thus allow ability for unserialized driver instance
load order.
Do not WARN_ON notification for unregistered pin, which can be invoked
for described case, instead just return error.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions")
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If parent pin was unregistered but child pin was not, the userspace
would see the "zombie" pins - the ones that were registered with
a parent pin (dpll_pin_on_pin_register(..)).
Technically those are not available - as there is no dpll device in the
system. Do not dump those pins and prevent userspace from any
interaction with them. Provide a unified function to determine if the
pin is available and use it before acting/responding for user requests.
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a kernel module is unbound but the pin resources were not entirely
freed (other kernel module instance of the same PCI device have had kept
the reference to that pin), and kernel module is again bound, the pin
properties would not be updated (the properties are only assigned when
memory for the pin is allocated), prop pointer still points to the
kernel module memory of the kernel module which was deallocated on the
unbind.
If the pin dump is invoked in this state, the result is a kernel crash.
Prevent the crash by storing persistent pin properties in dpll subsystem,
copy the content from the kernel module when pin is allocated, instead of
using memory of the kernel module.
Fixes: 9431063ad323 ("dpll: core: Add DPLL framework base functions")
Fixes: 9d71b54b65b1 ("dpll: netlink: Add DPLL framework base functions")
Reviewed-by: Jan Glaza <jan.glaza@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If pin type is not expected, or pin properities failed to allocate
memory, the unwind error path shall not destroy pin's xarrays, which
were not yet initialized.
Add new goto label and use it to fix broken error path.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After conversion of this driver to use powercap idle_inject core, this
driver doesn't use target_mwait value. So remove dead code.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The TUN can be used as vhost-net backend, and it is necessary to
count the packets transmitted from TUN to vhost-net/virtio-net.
However, there are some places in the receive path that were not
taken into account when using XDP. It would be beneficial to also
include new accounting for successfully received bytes using
dev_sw_netstats_rx_add.
Fixes: 761876c857cb ("tap: XDP support")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 8ae1aff0b331 ("tuntap: split out XDP logic") includes
dropped counter for XDP_DROP, XDP_ABORTED, and invalid XDP actions.
Unfortunately, that commit missed the dropped counter when error
occurs during XDP_TX and XDP_REDIRECT actions. This patch fixes
this issue.
Fixes: 8ae1aff0b331 ("tuntap: split out XDP logic")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The raw interrupt status of eic maybe set before the interrupt is enabled,
since the eic interrupt has a latch function, which would trigger the
interrupt event once enabled it from user side. To solve this problem,
interrupts generated before setting the interrupt trigger type are ignored.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Wenhua Lin <Wenhua.Lin@unisoc.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Since when the driver was converted to use the bus-based WMI
interface, the old GUID-based WMI functions are not used anymore.
Update the error message to avoid confusing users.
Compile-tested only.
Fixes: 75c487fcb69c ("platform/x86: intel-wmi-sbl-fw-update: Use bus-based WMI interface")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20240106224126.13803-1-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Accesses to resource[] member of struct pci_dev shall be wrapped with
pci_resource_n() for future compatibility. Call the helper function in
p2sb_read_bar0().
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240108062059.3583028-3-shinichiro.kawasaki@wdc.com
Tested-by Klara Modin <klarasmodin@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
p2sb_bar() unhides P2SB device to get resources from the device. It
guards the operation by locking pci_rescan_remove_lock so that parallel
rescans do not find the P2SB device. However, this lock causes deadlock
when PCI bus rescan is triggered by /sys/bus/pci/rescan. The rescan
locks pci_rescan_remove_lock and probes PCI devices. When PCI devices
call p2sb_bar() during probe, it locks pci_rescan_remove_lock again.
Hence the deadlock.
To avoid the deadlock, do not lock pci_rescan_remove_lock in p2sb_bar().
Instead, do the lock at fs_initcall. Introduce p2sb_cache_resources()
for fs_initcall which gets and caches the P2SB resources. At p2sb_bar(),
refer the cache and return to the caller.
Before operating the device at P2SB DEVFN for resource cache, check
that its device class is PCI_CLASS_MEMORY_OTHER 0x0580 that PCH
specifications define. This avoids unexpected operation to other devices
at the same DEVFN.
Link: https://lore.kernel.org/linux-pci/6xb24fjmptxxn5js2fjrrddjae6twex5bjaftwqsuawuqqqydx@7cl3uik5ef6j/
Fixes: 9745fb07474f ("platform/x86/intel: Add Primary to Sideband (P2SB) bridge support")
Cc: stable@vger.kernel.org
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20240108062059.3583028-2-shinichiro.kawasaki@wdc.com
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Tested-by Klara Modin <klarasmodin@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When booting a kernel with CONFIG_CFI_CLANG, there is a CFI failure when
accessing any of the values under
/sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00:
$ cat /sys/devices/system/cpu/intel_uncore_frequency/package_00_die_00/max_freq_khz
fish: Job 1, 'cat /sys/devices/system/cpu/int…' terminated by signal SIGSEGV (Address boundary error)
$ sudo dmesg &| grep 'CFI failure'
[ 170.953925] CFI failure at kobj_attr_show+0x19/0x30 (target: show_max_freq_khz+0x0/0xc0 [intel_uncore_frequency_common]; expected type: 0xd34078c5
The sysfs callback functions such as show_domain_id() are written as if
they are going to be called by dev_attr_show() but as the above message
shows, they are instead called by kobj_attr_show(). kCFI checks that the
destination of an indirect jump has the exact same type as the prototype
of the function pointer it is called through and fails when they do not.
These callbacks are called through kobj_attr_show() because
uncore_root_kobj was initialized with kobject_create_and_add(), which
means uncore_root_kobj has a ->sysfs_ops of kobj_sysfs_ops from
kobject_create(), which uses kobj_attr_show() as its ->show() value.
The only reason there has not been a more noticeable problem until this
point is that 'struct kobj_attribute' and 'struct device_attribute' have
the same layout, so getting the callback from container_of() works the
same with either value.
Change all the callbacks and their uses to be compatible with
kobj_attr_show() and kobj_attr_store(), which resolves the kCFI failure
and allows the sysfs files to work properly.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1974
Fixes: ae7b2ce57851 ("platform/x86/intel/uncore-freq: Use sysfs API to create attributes")
Cc: stable@vger.kernel.org
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20240104-intel-uncore-freq-kcfi-fix-v1-1-bf1e8939af40@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This has a reversed if statement so it accidentally disables the wmi
method before returning.
Fixes: 704af3a40747 ("platform/x86: wmi: Remove chardev interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/9c81251b-bc87-4ca3-bb86-843dc85e5145@moroto.mountain
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When an legacy WMI event handler is removed, an WMI event could
have called the handler just before it was removed, meaning the
handler could still be running after wmi_remove_notify_handler()
returns.
Something similar could also happens when using the WMI bus, as
the WMI core might still call the notify() callback from an WMI
driver even if its remove() callback was just called.
Fix this by introducing a rw semaphore which ensures that the
event state of a WMI device does not change while the WMI core
is handling an event for it.
Tested on a Dell Inspiron 3505 and a Acer Aspire E1-731.
Fixes: 1686f5444546 ("platform/x86: wmi: Incorporate acpi_install_notify_handler")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240103192707.115512-5-W_Armin@gmx.de
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
