| Age | Commit message (Collapse) | Author |
|---|
|
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.
There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.
For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
|
|
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@kernel.org
|
|
Originally OMAP MPUIO GPIO irqchip was implemented using Generic irq
chip, but after set of reworks Generic irq chip code was replaced by
common OMAP GPIO implementation and finally removed by
commit d2d05c65c40e ("gpio: omap: Fix regression for MPUIO interrupts").
Unfortunately, above commit left .irq_mask/unmask callbacks assigned
as below for MPUIO GPIO case:
irqc->irq_mask = irq_gc_mask_set_bit;
irqc->irq_unmask = irq_gc_mask_clr_bit;
This now causes boot failure on OMAP1 platforms, after
commit 450fa54cfd66 ("gpio: omap: convert to use generic irq handler")
which forces these callbacks to be called during GPIO IRQs mapping
from gpiochip_irq_map:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 75 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-rc1-e3-los_afe0c+-00002-g25379c0-dirty #1
Hardware name: Amstrad E3 (Delta)
task: c1836000 ti: c1838000 task.ti: c1838000
PC is at irq_gc_mask_set_bit+0x1c/0x60
LR is at __irq_do_set_handler+0x118/0x15c
pc : [<c004848c>] lr : [<c0047d4c>] psr: 600000d3
sp : c1839c90 ip : c1862c64 fp : c1839c9c
r10: 00000000 r9 : c0411950 r8 : c0411bbc
r7 : 00000000 r6 : c185c310 r5 : c00444e8 r4 : c185c300
r3 : c1854b50 r2 : 00000000 r1 : 00000000 r0 : c185c310
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000057
Process swapper (pid: 1, stack limit = 0xc1838190)
Stack: (0xc1839c90 to 0xc183a000)
[...]
Backtrace:
[<c0048470>] (irq_gc_mask_set_bit) from [<c0047d4c>] (__irq_do_set_handler+0x118/0x15c)
[<c0047c34>] (__irq_do_set_handler) from [<c0047dd4>] (__irq_set_handler+0x44/0x5c)
r6:00000000 r5:c00444e8 r4:c185c300
[<c0047d90>] (__irq_set_handler) from [<c0047e1c>] (irq_set_chip_and_handler_name+0x30/0x34)
r7:00000050 r6:00000000 r5:c00444e8 r4:00000050
[<c0047dec>] (irq_set_chip_and_handler_name) from [<c01b345c>] (gpiochip_irq_map+0x3c/0x8c)
r7:00000050 r6:00000000 r5:00000050 r4:c1862c64
[<c01b3420>] (gpiochip_irq_map) from [<c0049670>] (irq_domain_associate+0x7c/0x1c4)
r5:c185c310 r4:c185cb00
[<c00495f4>] (irq_domain_associate) from [<c0049894>] (irq_domain_add_simple+0x98/0xc0)
r8:c0411bbc r7:c185cb00 r6:00000050 r5:00000010 r4:00000001
[<c00497fc>] (irq_domain_add_simple) from [<c01b3328>] (_gpiochip_irqchip_add+0x64/0x10c)
r7:c1862c64 r6:c0419280 r5:c1862c64 r4:c1854b50
[<c01b32c4>] (_gpiochip_irqchip_add) from [<c01b79f4>] (omap_gpio_probe+0x2fc/0x63c)
r5:c1854b50 r4:c1862c10
[<c01b76f8>] (omap_gpio_probe) from [<c01fcf58>] (platform_drv_probe+0x2c/0x64)
r10:00000000 r9:c03e45e8 r8:00000000 r7:c0419294 r6:c0411984 r5:c0419294
r4:c0411950
[<c01fcf2c>] (platform_drv_probe) from [<c01fb668>] (really_probe+0x160/0x29c)
Hence, fix it by remove obsolete callbacks assignment. After this
change omap_gpio_mask_irq()/omap_gpio_unmask_irq() will be used
for MPUIO IRQs masking, but this now happens anyway from
omap_gpio_irq_startup/shutdown().
Cc: Tony Lindgren <tony@atomide.com>
Fixes: commit d2d05c65c40e ("gpio: omap: Fix regression for MPUIO interrupts")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'spi/fix/mediatek' and 'spi/fix/pl022' into spi-linus
|
|
|
|
Once TX has been enabled on a NIC, it is illegal to access skb,
as this skb might have been freed by another cpu, from TX completion
handler.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull nouveau and radeon fixes from Dave Airlie:
"Just some nouveau and radeon/amdgpu fixes.
The nouveau fixes look large as the firmware context files are
regenerated, but the actual change is quite small"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: make some dpm errors debug only
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC fixes from Alexandre Belloni:
"Two fixes for the ds1307 alarm and wakeup"
* tag 'rtc-4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: ds1307: fix alarm reading at probe time
rtc: ds1307: fix kernel splat due to wakeup irq handling
|
|
To avoid race conditions, traverse dev, media manager,
and target lists and also register, unregister entries
to/from them, should be always under the nvm_lock control.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The get_bb_tbl function takes ppa as a generic address, which is
converted to the ppa device address within the device driver. When
the update_bbtbl callback is called from get_bb_tbl, the device
specific ppa is used, instead of the generic ppa.
Make sure to pass the generic ppa.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The QEMU NVMe implementation uses Intel vendor, Intel device id, and the
first vendor specific byte to identify a LightNVM compatible nvme
instance.
Instead of using the Intel specific, use a preallocated from CNEX Labs
instead. This lets us uniquely identify a QEMU lightnvm device without
breaking other vendor specific work in the qemu device driver.
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
do device max_phys_sect boundary check first, otherwise
we will allocate dma_pools for devices whose max sectors
are beyond lightnvm support and register them.
Signed-off-by: Wenwei Tao <ww.tao0320@gmail.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If copy_to_user() fails we returned error but we missed releasing
devices.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
free allocated nvm block and gennvm lun structures when
gennvm register fails, otherwise it will cause memory leak.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We shouldn't compile an object file to get empty implementations;
conforms to linux coding style on conditional compilation.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Commit c0017ed71966 ("gpio: Introduce gpio descriptor 'name'") causes
OOPS on boot on LPC32xx boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0+ #707
Hardware name: LPC32XX SoC (Flattened Device Tree)
task: c381baa0 ti: c381e000 task.ti: c381e000
PC is at strcmp+0x10/0x40
LR is at gpiochip_add+0x3d0/0x4d4
pc : [<>] lr : [<>] psr: a0000093
sp : c381fd60 ip : c381fd70 fp : c381fd6c
[snip]
Backtrace:
[<>] (strcmp) from [<>] (gpiochip_add+0x3d0/0x4d4)
[<>] (gpiochip_add) from [<>] (lpc32xx_gpio_probe+0x44/0x60)
[<>] (lpc32xx_gpio_probe) from [<>] (platform_drv_probe+0x40/0x8c)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x110/0x294)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0xd4/0x1f0)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x38/0x4c)
[<>] (__platform_driver_register) from [<>] (lpc32xx_gpio_driver_init+0x18/0x20)
[<>] (lpc32xx_gpio_driver_init) from [<>] (do_one_initcall+0x108/0x1c8)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
This is caused by the fact that at the moment some GPIO names are set
to NULL, there is a hole in linear representation of one GPI bank, see
drivers/gpio/gpio-lpc32xx.c / gpi_p3_names[] for details.
The same problem most probably affects also gpio-cs5535.c, see
cs5535_gpio_names[].
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
- fix tcm-user backend driver expired cmd time processing (agrover)
- eliminate kref_put_spinlock_irqsave() for I/O completion (bart)
- fix iscsi login kthread failure case hung task regression (nab)
- fix COMPARE_AND_WRITE completion use-after-free race (nab)
- fix COMPARE_AND_WRITE with SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC non zero
SGL offset data corruption. (Jan + Doug)
- fix >= v4.4-rc1 regression for tcm_qla2xxx enable configfs attribute
(Himanshu + HCH)
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target/stat: print full t10_wwn.model buffer
target: fix COMPARE_AND_WRITE non zero SGL offset data corruption
qla2xxx: Fix regression introduced by target configFS changes
kref: Remove kref_put_spinlock_irqsave()
target: Invoke release_cmd() callback without holding a spinlock
target: Fix race for SCF_COMPARE_AND_WRITE_POST checking
iscsi-target: Fix rx_login_comp hang after login failure
iscsi-target: return -ENOMEM instead of -1 in case of failed kmalloc()
target/user: Do not set unused fields in tcmu_ops
target/user: Fix time calc in expired cmd processing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
"Specifics:
- several fixes and cleanups on Rockchip thermal drivers.
- add the missing support of RK3368 SoCs in Rockchip driver.
- small fixes on of-thermal, power_allocator, rcar driver, IMX, and
QCOM drivers, and also compilation fixes, on thermal.h, when thermal
is not selected"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
imx: thermal: use CPU temperature grade info for thresholds
thermal: fix thermal_zone_bind_cooling_device prototype
Revert "thermal: qcom_spmi: allow compile test"
thermal: rcar_thermal: remove redundant operation
thermal: of-thermal: Reduce log level for message when can't fine thermal zone
thermal: power_allocator: Use temperature reading from tz
thermal: rockchip: Support the RK3368 SoCs in thermal driver
thermal: rockchip: consistently use int for temperatures
thermal: rockchip: Add the sort mode for adc value increment or decrement
thermal: rockchip: improve the conversion function
thermal: rockchip: trivial: fix typo in commit
thermal: rockchip: better to compatible the driver for different SoCs
dt-bindings: rockchip-thermal: Support the RK3368 SoCs compatible
|
|
Cut 'n paste error saw it only process sizeof(t10_wwn.vendor) characters.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Given the following sample LIO subtopology,
% targetcli ls /loopback/
o- loopback ................................. [1 Target]
o- naa.6001405ebb8df14a ....... [naa.60014059143ed2b3]
o- luns ................................... [2 LUNs]
o- lun0 ................ [iblock/ram0 (/dev/ram0)]
o- lun1 ................ [iblock/ram1 (/dev/ram1)]
% lsscsi -g
[3:0:1:0] disk LIO-ORG IBLOCK 4.0 /dev/sdc /dev/sg3
[3:0:1:1] disk LIO-ORG IBLOCK 4.0 /dev/sdd /dev/sg4
the following bug can be observed in Linux 4.3 and 4.4~rc1:
% perl -e 'print chr$_ for 0..255,reverse 0..255' >rand
% perl -e 'print "\0" x 512' >zero
% cat rand >/dev/sdd
% sg_compare_and_write -i rand -D zero --lba 0 /dev/sdd
% sg_compare_and_write -i zero -D rand --lba 0 /dev/sdd
Miscompare reported
% hexdump -Cn 512 /dev/sdd
00000000 0f 0e 0d 0c 0b 0a 09 08 07 06 05 04 03 02 01 00
00000010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
00000200
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
this patch fixes following regression
# targetcli
[Errno 13] Permission denied: '/sys/kernel/config/target/qla2xxx/21:00:00:0e:1e:08:c7:20/tpgt_1/enable'
Fixes: 2eafd72939fd ("target: use per-attribute show and store methods")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch fixes the following kernel warning because it avoids that
IRQs are disabled while ft_release_cmd() is invoked (fc_seq_set_resp()
invokes spin_unlock_bh()):
WARNING: CPU: 3 PID: 117 at kernel/softirq.c:150 __local_bh_enable_ip+0xaa/0x110()
Call Trace:
[<ffffffff814f71eb>] dump_stack+0x4f/0x7b
[<ffffffff8105e56a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8105e65a>] warn_slowpath_null+0x1a/0x20
[<ffffffff81062b2a>] __local_bh_enable_ip+0xaa/0x110
[<ffffffff814ff229>] _raw_spin_unlock_bh+0x39/0x40
[<ffffffffa03a7f94>] fc_seq_set_resp+0xe4/0x100 [libfc]
[<ffffffffa02e604a>] ft_free_cmd+0x4a/0x90 [tcm_fc]
[<ffffffffa02e6972>] ft_release_cmd+0x12/0x20 [tcm_fc]
[<ffffffffa042bd66>] target_release_cmd_kref+0x56/0x90 [target_core_mod]
[<ffffffffa042caf0>] target_put_sess_cmd+0xc0/0x110 [target_core_mod]
[<ffffffffa042cb81>] transport_release_cmd+0x41/0x70 [target_core_mod]
[<ffffffffa042d975>] transport_generic_free_cmd+0x35/0x420 [target_core_mod]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joern Engel <joern@logfs.org>
Reviewed-by: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch addresses a case where iscsi_target_do_tx_login_io()
fails sending the last login response PDU, after the RX/TX
threads have already been started.
The case centers around iscsi_target_rx_thread() not invoking
allow_signal(SIGINT) before the send_sig(SIGINT, ...) occurs
from the failure path, resulting in RX thread hanging
indefinately on iscsi_conn->rx_login_comp.
Note this bug is a regression introduced by:
commit e54198657b65625085834847ab6271087323ffea
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Wed Jul 22 23:14:19 2015 -0700
iscsi-target: Fix iscsit_start_kthreads failure OOPs
To address this bug, complete ->rx_login_complete for good
measure in the failure path, and immediately return from
RX thread context if connection state did not actually reach
full feature phase (TARG_CONN_STATE_LOGGED_IN).
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Smatch complains about returning hard coded error codes, silence this
warning.
drivers/target/iscsi/iscsi_target_parameters.c:211
iscsi_create_default_params() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
TCMU sets TRANSPORT_FLAG_PASSTHROUGH, so INQUIRY commands will not be
emulated by LIO but passed up to userspace. Therefore TCMU should not
set these, just like pscsi doesn't.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Reversed arguments meant that we were doing nothing for cmds whose deadline
had passed.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Here are a few fixes I'd like to have in v4.4: a generic one for sysfs
and three for HiSilicon and DesignWare host controllers.
Summary:
NUMA:
- Prevent out of bounds access in numa_node override (Mathias Krause)
HiSilicon host bridge driver:
- Fix deferred probing (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect io_base assignment (Stanimir Varbanov)
- Move align_resource function pointer to pci_host_bridge structure
(Gabriele Paoloni)"
* tag 'pci-v4.4-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ARM/PCI: Move align_resource function pointer to pci_host_bridge structure
PCI: hisi: Fix deferred probing
PCI: designware: Remove incorrect io_base assignment
PCI: Prevent out of bounds access in numa_node override
|
|
Pull watchdog fixes from Wim Van Sebroeck:
- a null pointer dereference fix for omap_wdt
- some clock related fixes for pnx4008
- an underflow fix in wdt_set_timeout() for w83977f_wdt
- restart fix for tegra wdt
- Kconfig change to support Freescale Layerscape platforms
- fix for stopping the mtk_wdt watchdog
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: mtk_wdt: Use MODE_KEY when stopping the watchdog
watchdog: Add support for Freescale Layerscape platforms
watchdog: tegra: Stop watchdog first if restarting
watchdog: w83977f_wdt: underflow in wdt_set_timeout()
watchdog: pnx4008: make global wdt_clk static
watchdog: pnx4008: fix warnings caused by enabling unprepared clock
watchdog: omap_wdt: fix null pointer dereference
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a small backlog of at91 patches here, the most significant is
the addition of some sama5d2 Xplained nodes that were waiting on an
MFD include file to get merged through another tree.
We normally try to sort those out before the merge window opens, but
the maintainer wasn't aware of that here and I decided to merge the
changes this time as an exception.
On OMAP a series of audio changes for dra7 missed the merge window but
turned out to be necessary to fix a boot time imprecise external abort
error and to get audio working.
The other changes are the usual simple changes, here is a list sorted
by platform:
at91:
removal of a useless defconfig option
removal of some legacy DT pieces
use of the proper watchdog compatible string
update of the MAINTAINERS entries for some Atmel drivers
drivers/scpi:
hide get_scpi_ops in module from built-in code
imx:
add missing .irq_set_type for i.MX GPC irq_chip.
fix the wrong spi-num-chipselects settings for Vybrid DSPI devices.
fix a merge error in Vybrid dts regarding to ADC device property
keystone:
fix the optional PDSP firmware loading
fix linking RAM setup for QMs
fix crash with clk_ignore_unused
mediatek:
Enable SCPSYS power domain driver by default
mvebu:
fix QNAP TS219 power-off in dts
fix legacy get_irqnr_and_base for dove and orion5x
omap:
fix l4 related boot time errors for dm81xx
use lockless cldm/pwrdm api in omap4_boot_secondary
remove t410 abort handler to avoid hiding other critical errors
mark cpuidle tracepoints as _rcuidle
fix module alias for omap-ocp2scp
pxa:
palm: Fix typos in PWM lookup table code
renesas:
missing __initconst annotation for r8a7793_boards_compat_dt
rockchip:
disable mmc-tuning on the veyron-minnie board
adding the init state for the over-temperature-protection
zx:
only build power domain code when CONFIG_PM=y"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
ARM: OMAP4+: SMP: use lockless clkdm/pwrdm api in omap4_boot_secondary
arm: omap2+: add missing HWMOD_NO_IDLEST in 81xx hwmod data
ARM: orion5x: Fix legacy get_irqnr_and_base
ARM: dove: Fix legacy get_irqnr_and_base
soc: Mediatek: Enable SCPSYS power domain driver by default
ARM: dts: vfxxx: Fix dspi[01] spi-num-chipselects.
ARM: dts: keystone: k2l: fix kernel crash when clk_ignore_unused is not in bootargs
soc: ti: knav_qmss_queue: Fix linking RAM setup for queue managers
soc: ti: use request_firmware_direct() as acc firmware is optional
ARM: imx: add platform irq type setting in gpc
ARM: dts: vfxxx: Fix erroneous property in esdhc0 node
ARM: shmobile: r8a7793: proper constness with __initconst
scpi: hide get_scpi_ops in module from built-in code
ARM: zx: only build power domain code when CONFIG_PM=y
ARM: pxa: palm: Fix typos in PWM lookup table code
ARM: dts: Kirkwood: Fix QNAP TS219 power-off
ARM: dts: rockchip: Add OTP gpio pinctrl to rk3288 tsadc node
ARM: dts: rockchip: temporarily remove emmc hs200 speed from rk3288 minnie
MAINTAINERS: Atmel drivers: change NAND and ISI entries
ARM: at91/dt: sama5d2 Xplained: add several devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI fixes from Rafael Wysocki:
"These fix one recent regression (cpufreq core), fix up two features
added recently (ACPI CPPC support, SCPI support in the arm_big_little
cpufreq driver) and fix three older bugs in the intel_pstate driver.
Specifics:
- Fix a recent regression in the cpufreq core causing it to fail to
clean up sysfs directories properly on cpufreq driver removal
(Viresh Kumar).
- Fix a build problem in the SCPI support code recently added to the
arm_big_little cpufreq driver (Punit Agrawal).
- Fix up the recently added CPPC cpufreq frontend to process the CPU
coordination information provided by the platform firmware
correctly (Ashwin Chaugule).
- Fix the intel_pstate driver to behave as intended when switched
over to the "performance" mode via sysfs if hardware-driven P-state
selection (HWP) is enabled (Alexandra Yates).
- Fix two rounding errors in the intel_pstate driver that sometimes
cause it to use lower P-states than requested (Prarit Bhargava)"
* tag 'pm+acpi-4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
|
|
git://anongit.freedesktop.org/git/nouveau/linux-2.6 into drm-fixes
Ben Skeggs wrote:
A couple of regression fixes, some more boards whitelisted for a hw bug
workaround, gr/ucode fixes for hangs a user is seeing.
The changes look larger than they actually are due to the ucode binaries
(*.fucN.h) being regenerated.
* 'linux-4.4' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/volt/pwm/gk104: fix an off-by-one resulting in the voltage not being set
drm/nouveau/nvif: allow userspace access to its own client object
drm/nouveau/gr/gf100-: fix oops when calling zbc methods
drm/nouveau/gr/gf117-: assume no PPC if NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK is zero
drm/nouveau/gr/gf117-: read NV_PGRAPH_GPC_GPM_PD_PES_TPC_ID_MASK from correct GPC
drm/nouveau/gr/gf100-: split out per-gpc address calculation macro
drm/nouveau/bios: return actual size of the buffer retrieved via _ROM
drm/nouveau/instmem: protect instobj list with a spinlock
drm/nouveau/pci: enable c800 magic for some unknown Samsung laptop
drm/nouveau/pci: enable c800 magic for Clevo P157SM
|
|
* pm-cpufreq:
intel_pstate: Fix "performance" mode behavior with HWP enabled
cpufreq: SCPI: Depend on SCPI clk driver
cpufreq: intel_pstate: Fix limits->max_perf rounding error
cpufreq: intel_pstate: Fix limits->max_policy_pct rounding error
cpufreq: Always remove sysfs cpuX/cpufreq link on ->remove_dev()
* acpi-cppc:
cpufreq: CPPC: Initialize and check CPUFreq CPU co-ord type correctly
|
|
When submitting an identical spi_message multiple times via spi_sync
the spi_message.frame_length does not get reset to 0 in __spi_validate
before adding up all spi_transfer.len resulting in
frame_length > actual_length on all but the first spi_sync call.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When the AP queue depth of requests was reached additional requests
have been ignored. These request are stuck in the request queue.
The AP queue handling now push the next waiting request into the
queue after fetching a previous serviced and finished reply.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
s3c2410_plls_add is a device notifier that may be called at runtime and
is correctly not marked __init. However it calls s3c_plltab_register()
which is marked __init, and that triggers a build error when we are
checking for section mismatches:
WARNING: vmlinux.o(.text+0x195e0): Section mismatch in reference from the function s3c2410_plls_add() to the function .init.text:s3c_plltab_register()
The function s3c2410_plls_add() references
the function __init s3c_plltab_register().
This is often because s3c2410_plls_add lacks a __init
annotation or the annotation of s3c_plltab_register is wrong.
This removes the __init annotation from s3c2410_plls_add as well as the
__initdata section annotations from s3c2440_plls_12 and s3c2440_plls_169344,
which in turn are referenced from s3c2410_plls_add.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen bug fixes from David Vrabel:
- Fix gntdev and numa balancing.
- Fix x86 boot crash due to unallocated legacy irq descs.
- Fix overflow in evtchn device when > 1024 event channels.
* tag 'for-linus-4.4-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/evtchn: dynamically grow pending event channel ring
xen/events: Always allocate legacy interrupts on PV guests
xen/gntdev: Grant maps should not be subject to NUMA balancing
|
|
If more than 1024 event channels are bound to a evtchn device then it
possible (even with well behaved applications) for the ring to
overflow and events to be lost (reported as an -EFBIG error).
Dynamically increase the size of the ring so there is always enough
space for all bound events. Well behaved applicables that only unmask
events after draining them from the ring can thus no longer lose
events.
However, an application could unmask an event before draining it,
allowing multiple entries per port to accumulate in the ring, and a
overflow could still occur. So the overflow detection and reporting
is retained.
The ring size is initially only 64 entries so the common use case of
an application only binding a few events will use less memory than
before. The ring size may grow to 512 KiB (enough for all 2^17
possible channels). This order 7 kmalloc() may fail due to memory
fragmentation, so we fall back to trying vmalloc().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
|
|
After commit 8c058b0b9c34 ("x86/irq: Probe for PIC presence before
allocating descs for legacy IRQs") early_irq_init() will no longer
preallocate descriptors for legacy interrupts if PIC does not
exist, which is the case for Xen PV guests.
Therefore we may need to allocate those descriptors ourselves.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
Doing so will cause the grant to be unmapped and then, during
fault handling, the fault to be mistakenly treated as NUMA hint
fault.
In addition, even if those maps could partcipate in NUMA
balancing, it wouldn't provide any benefit since we are unable
to determine physical page's node (even if/when VNUMA is
implemented).
Marking grant maps' VMAs as VM_IO will exclude them from being
part of NUMA balancing.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
|
|
With the actual code, read_alarm() always returns -EINVAL when called
during the RTC device registration. This prevents from retrieving an
already configured alarm in hardware.
This patch fixes the issue by moving the HAS_ALARM bit configuration
(if supported by the hardware) above the rtc_device_register() call.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The WARN_ON() macro only takes a condition argument, it doesn't take
a message. I have converted this to WARN() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
The remoteproc core uses a static ida named rproc_dev_index for
assigning an automatic index number to a registered remoteproc.
The ida core may allocate some internal idr cache layers and ida
bitmap upon any ida allocation, and all these layers are truely
freed only upon the ida destruction. The rproc_dev_index ida is
not destroyed at present, leading to a memory leak when using the
remoteproc core as a module and atleast one rproc device is
registered and unregistered.
Fix this by invoking ida_destroy() in the remoteproc core module
exit.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
In ttm_write_lock(), the uninterruptible path should call
__ttm_write_lock() not __ttm_read_lock(). This fixes a vmwgfx hang
on F23 start up.
syeh: Extracted this from one of Thomas' internal patches.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
Recent gcc versions warn about reading from a negative offset of
an on-stack array:
drivers/remoteproc/remoteproc_debugfs.c: In function 'rproc_recovery_write':
drivers/remoteproc/remoteproc_debugfs.c:167:9: warning: 'buf[4294967295u]' may be used uninitialized in this function [-Wmaybe-uninitialized]
I don't see anything in sys_write() that prevents us from
being called with a zero 'count' argument, so we should
add an extra check in rproc_recovery_write() to prevent the
access and avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 2e37abb89a2e ("remoteproc: create a 'recovery' debugfs entry")
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
|
|
into drm-fixes
Radeon and amdgpu fixes for 4.4:
- DPM fixes for r7xx devices
- VCE fixes for Stoney
- GPUVM fixes
- Scheduler fixes
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make some dpm errors debug only
drm/radeon: make rv770_set_sw_state failures non-fatal
drm/amdgpu: move dependency handling out of atomic section v2
drm/amdgpu: optimize scheduler fence handling
drm/amdgpu: remove vm->mutex
drm/amdgpu: add mutex for ba_va->valids/invalids
drm/amdgpu: adapt vce session create interface changes
drm/amdgpu: vce use multiple cache surface starting from stoney
drm/amdgpu: reset vce trap interrupt flag
|
|
Commit 4f258a46346c ("sd: Fix maximum I/O size for BLOCK_PC requests")
had the unfortunate side-effect of removing an implicit clamp to
BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer
code. This caused problems for some SMR drives.
Debugging this issue revealed a few problems with the existing
infrastructure since the block layer didn't know how to deal with
device-imposed limits, only limits set by the I/O controller.
- Introduce a new queue limit, max_dev_sectors, which is used by the
ULD to signal the maximum sectors for a REQ_TYPE_FS request.
- Ensure that max_dev_sectors is correctly stacked and taken into
account when overriding max_sectors through sysfs.
- Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer
values for later processing.
- In sd_revalidate() set the queue's max_dev_sectors based on the
MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value
is not reported, fall back to a cap based on the CDB TRANSFER LENGTH
field size.
- In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits
VPD--if reported and sane--to signal the preferred device transfer
size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS.
- blk_limits_max_hw_sectors() is no longer used and can be removed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: sweeneygj@gmx.com
Tested-by: Arzeets <anatol.pomozov@gmail.com>
Tested-by: David Eisner <david.eisner@oriel.oxon.org>
Tested-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
