| Age | Commit message (Collapse) | Author |
|---|
|
vc4_dsi was registering both dsi0 and dsi1 as VC4_ENCODER_TYPE_DSI1
which seemed to work OK for a single DSI display, but fails
if there are two DSI displays connected.
Update to register the correct type.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-15-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
For slightly unknown reasons, dsi0 takes a different pixel format
to dsi1, and that has to be set in the pixel valve.
Amend the setup accordingly.
Fixes: a86773d120d7 ("drm/vc4: Add support for feeding DSI encoders from the pixel valve.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-14-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3f2 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
On Pi0-3 the driver allocates a buffer and requests a DMA channel
because the ARM can't write to DSI1's registers directly.
However, we never release that buffer or channel. Let's add a
device-managed action to release each.
Fixes: 4078f5757144 ("drm/vc4: Add DSI driver")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-12-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
In a couple of error/incomplete configuration cases, the
DPI_FORMAT bits wouldn't get set.
Enforce our RGB888 default in all these cases.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-11-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
DRM provides flags for inverting pixel clock and output enable
signals, but these were not mapped to the relevant registers.
Add those mappings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-10-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The hardware can combine H&V syncs onto the output enable line
as composite syncs, so add the relevant configuration to do that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-9-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This allows easy analysis of display lists when debugging.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-8-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Move from only supporting the default of pre-multiplied
alpha to supporting user specified blend mode using the
standardised property.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-7-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The current plane margin calculation code clips the right and bottom
edges of the range based using the left and top margins.
This is obviously wrong, so let's fix it.
Fixes: 666e73587f90 ("drm/vc4: Take margin setup into account when updating planes")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-6-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 21af94cf1a4c ("drm/vc4: Add support for scaling of display planes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The core clock computation takes into account both the load due to the
input (ie, planes) and its output (ie, encoders).
However, while the input load needs to consider all the planes, and thus
sum all of their associated loads, the output happens mostly in
parallel.
Therefore, we need to consider only the maximum of all the output loads,
and not the sum like we were doing. This resulted in a clock rate way
too high which could be discarded for being too high by the clock
framework.
Since recent changes, the clock framework will even downright reject it,
leading to a core clock being too low for its current needs.
Fixes: 16e101051f32 ("drm/vc4: Increase the core clock based on HVS load")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-4-maxime@cerno.tech
|
|
We currently ignore the clk_set_min_rate return code assuming it would
succeed. However, it can fail if we ask for a rate higher than the
current maximum for example.
Since we can't fail in atomic_commit, at least warn on failure.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-3-maxime@cerno.tech
|
|
vc4_drv isn't necessarily under the /soc node in DT as it is a
virtual device, but it is the one that does the allocations.
The DMA addresses are consumed by primarily the HVS or V3D, and
those require VideoCore cache alias address mapping, and so will be
under /soc.
During probe find the a suitable device node for HVS or V3D,
and adopt the DMA configuration of that node.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-2-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This function is supposed to return zero or negative error codes but it
accidentally returns true on failure.
Fixes: 92a020747d6c ("drm/i915: Split shared dpll .get_dplls() into compute and get phases")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YrVcHArNMTGCSy+9@kili
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
|
|
Fix SoC detection for SAM9X60 SiPs:
SAM9X60D5M
SAM9X60D1G
SAM9X60D6K
Fixes: af3a10513cd6 ("drivers: soc: atmel: add per soc id and version match masks")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220616081344.1978664-1-claudiu.beznea@microchip.com
|
|
The mask_ack operation clears the interrupt by writing to the PICSR
register. This we don't want for level triggered interrupt because
it does not actually clear the interrupt on the source hardware.
This was causing issues in qemu with multi core setups where
interrupts would continue to fire even though they had been cleared in
PICSR.
Just remove the mask_ack operation.
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
|
|
This SoC shall use the mediatek-cpufreq driver, or the system will
crash upon any clock scaling request: add it to the cpufreq-dt-platdev
blocklist.
Fixes: 39b360102f3a ("cpufreq: mediatek: Add support for MT8186")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In pmac_cpufreq_init_MacRISC3(), we need to add corresponding
of_node_put() for the three node pointers whose refcount have
been incremented by of_find_node_by_name().
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Offlining cpu6 and cpu7 and then onlining cpu6 hangs on
sc7180-trogdor-lazor because the throttle interrupt doesn't exist.
Similarly, things go sideways when suspend/resume runs. That's because
the qcom_cpufreq_hw_cpu_online() and qcom_cpufreq_hw_lmh_exit()
functions are calling genirq APIs with an interrupt value of '-6', i.e.
-ENXIO, and that isn't good.
Check the value of the throttle interrupt like we already do in other
functions in this file and bail out early from lmh code to fix the hang.
Reported-by: Rob Clark <robdclark@chromium.org>
Cc: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: a1eb080a0447 ("cpufreq: qcom-hw: provide online/offline operations")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes: 157f527639da ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ]
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Replace apprpriately with appropriately.
Fixes: 1e4d84c6589e9 ("drm/doc: Polish plane composition property docs")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Simon Ser <contact@emersion.fr>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20220628003407.77765-1-marex@denx.de
|
|
We should respect link partner capabilities and not force flow control
support on every link. Even more, in current state the MAC driver do not
advertises pause support so we should not keep flow control enabled at
all.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.
On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".
With this patch we will notify usbnet about link status change provided by the
PHYlib.
Fixes: e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This should be bitwise operator not logical.
Fixes: 862cd659a6fb ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Shreenidhi Shedi <sshedi@vmware.com>
Link: https://lore.kernel.org/r/20220626132947.3992423-1-sshedi@vmware.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
epic_close() calls epic_rx() and uses dma buffer, but in epic_remove_one()
we already freed the dma buffer. To fix this issue, reorder function calls
like in the .probe function.
BUG: KASAN: use-after-free in epic_rx+0xa6/0x7e0 [epic100]
Call Trace:
epic_rx+0xa6/0x7e0 [epic100]
epic_close+0xec/0x2f0 [epic100]
unregister_netdev+0x18/0x20
epic_remove_one+0xaa/0xf0 [epic100]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Yilun Wu <yiluwu@cs.stonybrook.edu>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Link: https://lore.kernel.org/r/20220627043351.25615-1-ztong0001@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While looking at a syzbot report I noticed the NAPI only gets
disabled before it's deleted. I think that user can detach
the queue before destroying the device and the NAPI will never
be stopped.
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver")
Acked-by: Petar Penkov <ppenkov@aviatrix.com>
Link: https://lore.kernel.org/r/20220623042105.2274812-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the controller is behind an IOMMU then the IOMMU IOVA caching range can
affect performance, as discussed in [0].
Limit the max HW sectors to not exceed this limit. We need to hardcode the
value until a proper DMA mapping API is available.
[0] https://lore.kernel.org/linux-iommu/20210129092120.1482-1-thunder.leizhen@huawei.com/
Link: https://lore.kernel.org/r/1655988119-223714-1-git-send-email-john.garry@huawei.com
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
On dm-raid table load (using raid_ctr), dm-raid allocates an array
rs->devs[rs->raid_disks] for the raid device members. rs->raid_disks
is defined by the number of raid metadata and image tupples passed
into the target's constructor.
In the case of RAID layout changes being requested, that number can be
different from the current number of members for existing raid sets as
defined in their superblocks. Example RAID layout changes include:
- raid1 legs being added/removed
- raid4/5/6/10 number of stripes changed (stripe reshaping)
- takeover to higher raid level (e.g. raid5 -> raid6)
When accessing array members, rs->raid_disks must be used in control
loops instead of the potentially larger value in rs->md.raid_disks.
Otherwise it will cause memory access beyond the end of the rs->devs
array.
Fix this by changing code that is prone to out-of-bounds access.
Also fix validate_raid_redundancy() to validate all devices that are
added. Also, use braces to help clean up raid_iterate_devices().
The out-of-bounds memory accesses was discovered using KASAN.
This commit was verified to pass all LVM2 RAID tests (with KASAN
enabled).
Cc: stable@vger.kernel.org
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
SLPC min/max frequency updates require H2G calls. We are seeing
timeouts when GuC channel is backed up and it is unable to respond
in a timely fashion causing warnings and affecting CI.
This is seen when waitboosting happens during a stress test.
this patch updates the waitboost path to use a non-blocking
H2G call instead, which returns as soon as the message is
successfully transmitted.
v2: Use drm_notice to report any errors that might occur while
sending the waitboost H2G request (Tvrtko)
v3: Add drm_notice inside force_min_freq (Ashutosh)
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623003225.23301-1-vinay.belgaumkar@intel.com
|
|
This was a typo, we didn't actually want to return zero.
Fixes: a61acbbe9cf8 ("drm/msm: Track "seqno" fences by idr")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491145/
Link: https://lore.kernel.org/r/20220624184528.4036837-1-robdclark@gmail.com
|
|
For execlists backend, current implementation of Wa_22011802037 is to
stop the CS before doing a reset of the engine. This WA was further
extended to wait for any pending MI FORCE WAKEUPs before issuing a
reset. Add the extended steps in the execlist path of reset.
In addition, extend the WA to gen11.
v2: (Tvrtko)
- Clarify comments, commit message, fix typos
- Use IS_GRAPHICS_VER for gen 11/12 checks
v3: (Daneile)
- Drop changes to intel_ring_submission since WA does not apply to it
- Log an error if MSG IDLE is not defined for an engine
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Fixes: f6aa0d713c88 ("drm/i915: Add Wa_22011802037 force cs halt")
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621192105.2100585-1-umesh.nerlige.ramappa@intel.com
|
|
Using two different types of workoads, it was observed that
guc_update_engine_gt_clks was being called too frequently and/or
causing a CPU-to-lmem bandwidth hit over PCIE. Details on
the workloads and numbers are in the notes below.
Background: At the moment, guc_update_engine_gt_clks can be invoked
via one of 3 ways. #1 and #2 are infrequent under normal operating
conditions:
1.When a predefined "ping_delay" timer expires so that GuC-
busyness can sample the GTPM clock counter to ensure it
doesn't miss a wrap-around of the 32-bits of the HW counter.
(The ping_delay is calculated based on 1/8th the time taken
for the counter go from 0x0 to 0xffffffff based on the
GT frequency. This comes to about once every 28 seconds at a
GT frequency of 19.2Mhz).
2.In preparation for a gt reset.
3.In response to __gt_park events (as the gt power management
puts the gt into a lower power state when there is no work
being done).
Root-cause: For both the workloads described farther below, it was
observed that when user space calls IOCTLs that unparks the
gt momentarily and repeats such calls many times in quick succession,
it triggers calling guc_update_engine_gt_clks as many times. However,
the primary purpose of guc_update_engine_gt_clks is to ensure we don't
miss the wraparound while the counter is ticking. Thus, the solution
is to ensure we skip that check if gt_park is calling this function
earlier than necessary.
Solution: Snapshot jiffies when we do actually update the busyness
stats. Then get the new jiffies every time intel_guc_busyness_park
is called and bail if we are being called too soon. Use half of the
ping_delay as a safe threshold.
NOTE1: Workload1: IGTs' gem_create was modified to create a file handle,
allocate memory with sizes that range from a min of 4K to the max supported
(in power of two step-sizes). Its maps, modifies and reads back the
memory. Allocations and modification is repeated until total memory
allocation reaches the max. Then the file handle is closed. With this
workload, guc_update_engine_gt_clks was called over 188 thousand times
in the span of 15 seconds while this test ran three times. With this patch,
the number of calls reduced to 14.
NOTE2: Workload2: 30 transcode sessions are created in quick succession.
While these sessions are created, pcm-iio tool was used to measure I/O
read operation bandwidth consumption sampled at 100 milisecond intervals
over the course of 20 seconds. The total bandwidth consumed over 20 seconds
without this patch was measured at average at 311KBps per sample. With this
patch, the number went down to about 175Kbps which is about a 43% savings.
Signed-off-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623023157.211650-2-alan.previn.teres.alexis@intel.com
|
|
This reverts commit 1e98d8c52ed5dfbaf273c4423c636525c2ce59e7.
The problem with this patch is that it makes i915_request to hold a
reference to intel_context, which in turn holds a reference on the VM.
This strong back referencing can lead to reference loops which leads
to resource leak.
An example is the upcoming VM_BIND work which requires VM to hold
a reference to some shared VM specific BO. But this BO's dma-resv
fences holds reference to the i915_request thus leading to reference
loop.
v2:
Do not use reserved requests for virtual engines
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Mathew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614184348.23746-3-ramalingam.c@intel.com
|
|
In i915_fence_get_driver_name(), user may not hold a
reference to rq->engine. Hence do not access it. Instead,
store required device private pointer in 'rq->i915' and use it.
Signed-off-by: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Suggested-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220614184348.23746-2-ramalingam.c@intel.com
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes all over the place, most notably we are disabling
IRQ hardening (again!)"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_ring: make vring_create_virtqueue_split prettier
vhost-vdpa: call vhost_vdpa_cleanup during the release
virtio_mmio: Restore guest page size on resume
virtio_mmio: Add missing PM calls to freeze/restore
caif_virtio: fix race between virtio_device_ready() and ndo_open()
virtio-net: fix race between ndo_open() and virtio_device_ready()
virtio: disable notification hardening by default
virtio: Remove unnecessary variable assignments
virtio_ring : keep used_wrap_counter in vq->last_used_idx
vduse: Tie vduse mgmtdev and its device
vdpa/mlx5: Initialize CVQ vringh only once
vdpa/mlx5: Update Control VQ callback information
|
|
The LUTs are a display feature so move the details into
the display portion of the device info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
XE_LPD_CURSOR_OFFSETS is a duplicate of TGL_CURSOR_OFFSETS.
Just use the latter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Stop hand rolling _MMIO_TRANS2() and just use the real thing.
Note that this register isn't even used atm, hence why this
builds despite the _PIPE2() macro not actually existing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Stop hand rolling _MMIO_TRANS2() and just use the real thing.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The other similar macros have the _MMIO prefix, so give
it also to _CURSOR2.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Using a signed type for the register offsets doesn't really
make sense. Switch to u32.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The display register offsets are display stuff so stick
into the display portion of the device info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
The display register offsets are display stuff so stick
into the display portion of the device info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Replace the deprecated ida_simple_{get,remove} with ida_{alloc,free}.
Link: https://lore.kernel.org/r/20220616055052.4559-1-liubo03@inspur.com
Signed-off-by: Bo Liu <liubo03@inspur.com>
[sudeep.holla: Replace ida_alloc_min with ida_alloc as suggested by Cristian]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
DBUF is a display thing, so move it into the display
portion of the device info.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220623130900.26078-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Eliminate the PIPECONF RMWs from .comit_commit() so
that we can finally declare the whole vblank evade part
(and the noarm() part) of the pipe commit free of register
reads. Or at least I hope that's the last read...
Only the i9xx/ilk codepaths need this for now, but let's
add the same thing for hsw+ just in case we want to start
calling that during fastsets at some point (eg. to change
dithering settings/etc.).
Should open up the way to start experimenting with
different DSB usage approaches for pipe commits.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220413192607.27533-1-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
For imported dma-buf objects we leave the object as cache_coherent = 0
across all platforms, which is reasonable given that have no clue what
the memory underneath is, and its not like the driver can ever manually
clflush the pages anyway (like with i915_gem_clflush_object) for such
objects. However on discrete we choose to treat cache_dirty = true as a
programmer error, leading to a warning. The simplest fix looks to be to
just change the ordering in cpu_write_needs_clflush to prevent ever
setting cache_dirty for dma-buf objects on discrete.
Fixes: d028a7690d87 ("drm/i915/dmabuf: Fix prime_mmap to work when using LMEM")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5266
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622155919.355081-1-matthew.auld@intel.com
(cherry picked from commit 563aaf4a928def2d36d1b3de0a4b515e2477b4da)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Currently i915 disables d3cold for i915 pci dev.
This blocks D3 for i915 gfx pci upstream bridge (VSP).
Let's disable d3cold at gfx root port to make sure that
i915 gfx VSP can transition to D3 to save some power.
We don't need to disable/enable d3cold in rpm, s2idle
suspend/resume handlers. Disabling/Enabling d3cold at
gfx root port in probe/remove phase is sufficient.
Fixes: 1a085e23411d ("drm/i915: Disable D3Cold in s2idle and runtime pm")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220616122249.5007-1-anshuman.gupta@intel.com
(cherry picked from commit 138c2fca6f408f397ea8fbbbf33203f244d96e01)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Add missing else in set_proto_ctx_param() to fix coverity issue.
Addresses-Coverity: ("Unused value")
Fixes: d4433c7600f7 ("drm/i915/gem: Use the proto-context to handle create parameters (v5)")
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: katrinzhou <katrinzhou@tencent.com>
[tursulin: fixup alignment]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621124926.615884-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 7482a65664c16cc88eb84d2b545a1fed887378a1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
