| Age | Commit message (Collapse) | Author |
|---|
|
Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.
Cc: stable@vger.kernel.org #3.3+
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.
Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.
Note that we don't use queues 20 and higher today and
doing so needs more work than this.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pull HSI fixes and ABI documentation from Carlos Chinea
* tag 'hsi_fixes_for_3.4' of git://gitorious.org/kernel-hsi/kernel-hsi:
HSI: Add HSI ABI documentation
HSI: hsi_char: Remove max_data_size from sysfs
HSI: hsi: Rework hsi_event interface
HSI: hsi: Remove controllers and ports from the bus
HSI: hsi: Fix error path cleanup on client registration
HSI: hsi: Rework hsi_controller release
|
|
This change adds 0x0489:0xe033 to the btusb module.
This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.
Output from /sys/kernel/debug/usb/devices:
T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e033 Rev= 2.29
S: Manufacturer=Broadcom Corp
S: Product=Acer Module
S: SerialNumber=60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 32 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 32 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 64 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 32 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: Steven Harms <sjharms@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo@padovan.org>
|
|
The asix.c USB Ethernet driver avoids ending a tx transfer with a zero-
length packet by appending a four-byte padding to transfers whose length
is a multiple of maxpacket. However, the hard-coded 512 byte maxpacket
length is valid for high-speed USB only; full-speed USB uses 64 byte
packets.
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY connect attempts fail if no PHY id is specified in the emac platform
data and another mdio bus has been registered before 'davinci_mdio' bus. In
this case when configuring the interface, there will be an attempt to
connect to already attached PHY on the previously registered mdio bus:
net eth1: PHY already attached
net eth1: could not connect to phy smsc911x-0:01
IP-Config: Failed to open eth1
IP-Config: Device `eth1' not found
Fix this by modifying match_first_device() to match first PHY device
on 'davinci_mdio' bus.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we receive an interrupt too early before we set up ports in the probe
function, there won't be any port ready to handle it.
Only registering the irq after the ports are setup fixes the problem,
and works fine without losing any interrupts.
This causes crashes in some situations:
[c000000f7ff7fd60] d000000008e223f0 .ehea_neq_tasklet+0x78/0x148 [ehea]
[c000000f7ff7fe00] c0000000000b6cac .tasklet_hi_action+0xdc/0x210
[c000000f7ff7fea0] c0000000000b7cc8 .__do_softirq+0x178/0x300
[c000000f7ff7ff90] c000000000022694 .call_do_softirq+0x14/0x24
[c000000f68ee7900] c000000000010e04 .do_softirq+0xec/0x110
[c000000f68ee79a0] c0000000000b789c .irq_exit+0xac/0xe0
[c000000f68ee7a20] c0000000000110bc .do_IRQ+0x114/0x2a8
[c000000f68ee7ae0] c00000000000553c hardware_interrupt_entry+0x18/0x1c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The previous blkt defaults for OSA Express 4 cards produced inadequate
performance for streaming workloads. The present patch will apply a
set of more appropriate defaults.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There exist qeth sysfs blkt attributes to change the default blkt
values. But blkt changes are reset during online setting due to a 2nd
invocation of qeth_determine_capabilites(). This patch makes sure
blkt default values are configured during 1st run of
qeth_determine_capabilities() only. Thus blkt changes are kept
during online setting.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Reported-by: Horst Hartmann <horst.hartmann@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make smsc95xx recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1488 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Inspired by same fix on cdc_eem 78fb72f7936c01d5b426c03a691eca082b03f2b9.
Tested on ARM/Beagle.
Signed-off-by: Stephane Fillod <fillods@users.sf.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull a few more md bug fixes from NeilBrown:
"2 are tagged for -stable, one being for a fairly serious bug that can
corrupt metadata and make it hard to recovery an array. The other is
for a more recent regression since 3.3"
* tag 'md-3.4-fixes' of git://neil.brown.name/md:
md: fix possible corruption of array metadata on shutdown.
md: don't call ->add_disk unless there is good reason.
DM RAID: Use safe version of rdev_for_each
|
|
commit c744a65c1e2d59acc54333ce8
md: don't set md arrays to readonly on shutdown.
removed the possibility of a 'BUG' when data is written to an array
that has just been switched to read-only, but also introduced the
possibility that the array metadata could be corrupted.
If, when md_notify_reboot gets the mddev lock, the array is
in a state where it is assembled but hasn't been started (as can
happen if the personality module is not available, or in other unusual
situations), then incorrect metadata will be written out making it
impossible to re-assemble the array.
So only call __md_stop_writes() if the array has actually been
activated.
This patch is needed for any stable kernel which has had the above
commit applied.
Cc: stable@vger.kernel.org
Reported-by: Christoph Nelles <evilazrael@evilazrael.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Commit 7bfec5f35c68121e7b18
md/raid5: If there is a spare and a want_replacement device, start replacement.
cause md_check_recovery to call ->add_disk much more often.
Instead of only when the array is degraded, it is now called whenever
md_check_recovery finds anything useful to do, which includes
updating the metadata for clean<->dirty transition.
This causes unnecessary work, and causes info messages from ->add_disk
to be reported much too often.
So refine md_check_recovery to only do any actual recovery checking
(including ->add_disk) if MD_RECOVERY_NEEDED is set.
This fix is suitable for 3.3.y:
Cc: stable@vger.kernel.org
Reported-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Fix segfault caused by using rdev_for_each instead of rdev_for_each_safe
Commit dafb20fa34320a472deb7442f25a0c086e0feb33 mistakenly replaced a safe
iterator with an unsafe one when making some macro changes.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
On 32-bit systems, a large args->num_cliprects from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 432e58ed ("drm/i915: Avoid
allocation for execbuffer object list").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
On 32-bit systems, a large args->buffer_count from userspace via ioctl
may overflow the allocation size, leading to out-of-bounds access.
This vulnerability was introduced in commit 8408c282 ("drm/i915:
First try a normal large kmalloc for the temporary exec buffers").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
With commit a2ef5c4fd44ce3922435139393b89f2cce47f576
"ACPI: Move module parameter gts and bfs to sleep.c" the wake_sleep_flags
is required when calling acpi_enter_sleep_state, which means
that if there are functions outside the sleep.c code they
can't get the wake_sleep_flags values.
This converts the function in to a exported value and converts
the module config operands to a function.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Lin Ming <ming.m.lin@intel.com>
[v2: Parameters can be turned on/off dynamically]
[v3: unsigned char -> u8]
[v4: val -> kp->arg]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1335150198-21899-2-git-send-email-konrad.wilk@oracle.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Under some circumstances, a PCI-based driver reports the following OOPs:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>] [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] 0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---
This oops is due to interrupts not being disabled in this particular path.
Reported-by: Dave Airlie <airlied@gmail.com>
Tested-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution. Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:
Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.
After that you need to reload the driver to get it working again.
This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106
This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.
This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852e4345d0a31af593c46738ca8614bff
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to unifying regulatory limit handling
commit ca2c68cc7bc80fc4504fb420df04cce99c9ee6ec
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
A small fallout from Vinod's conversions to dma_transfer_direction,
this small comparison was done with a dma_data_direction instead.
Fix it by comparing against the correct enum.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The patch "ARM: amba: Remove AMBA level regulator support" breaks
the DMA40 driver since the <linux/amba/bus.h> header implicitly
included the regulator consumer header. So include it explicitly
and fix the build error.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
can be directly stopped by issuing a SUSPEND_REQ on the EE
bits. There is no need to suspend the physical channel and
restart it.
Also, the support for pre-V2 hw is discontinued.
EE bits for writing:
00: disable only if AS=11 or AS=00
01: enable
10: suspend_req only if AS=01 & EE=01 or EE=11
11: round / no change for writing
Signed-off-by: Narayanan G <narayanan.gopalakrishnan@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
with this patch, if the memory region is physically non-continuous
then VM_MIXEDMAP is set to vm->vm_flags otherwise VM_PFNMAP.
we had missed this flag setting.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
this patch fixes the problem that the physical memory region to be mapped
to user space could be exceeded. if page fault address was placed at between
buffer start and end then memory region to be mapped would be exceeded.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
the gem was already allocated at gem allocation time but is allocated
at page fault handler so this patch fixes the problem that gem was
allocated one more time.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Remove max_data_size sysfs entry. Otherwise is possible
to have a buffer overrun if its value is increased after
the device is open.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove custom hack and make use of the notifier chain interfaces for
delivering events from the ports to their associated clients.
Clients that want to receive port events need to register their callbacks
using hsi_register_port_event(). The callbacks can be called in interrupt
context. Use hsi_unregestier_port_event() to undo the registration.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
HSI controllers and ports do not belong to the HSI bus.
Those devices are not supposed to have a driver attached to them.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
HSI client structure should be freed on error path after
calling device_registration by dropping a reference to it.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use the proper release mechanism for hsi_controller and
hsi_ports structures. Free the structures through their
associated device release callbacks.
Signed-off-by: Carlos Chinea <carlos.chinea@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This reverts commit a692b0eec5efae382dfa800e8b4b083f172921a7.
Tom reports:
[ 8.741033] ------------[ cut here ]------------
[ 8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[ 8.741040] Hardware name: To Be Filled By O.E.M.
[ 8.741041] sysfs: cannot create duplicate filename
...and missing 2 out of 4 drives connected to mvsas. Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique. However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas. So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7. The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.
Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: Tom Rini <trini@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:
sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This changes the ordering of initialization and probing events from:
1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
3/ schedule port probe in DISCE_PROBE
This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:
BUG: unable to handle kernel paging request at 0000000000003b10
IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
...
[<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
[<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
[<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
[<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
[<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]
...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: Michal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover(). The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change. When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled. So change
the code to skip the sas_address and change count updates when ata_eh is
active.
Cc: Jack Wang <jack_wang@usish.com>
Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since the domain_device can out live the scsi_target we need the rphy to
follow suit otherwise we run into issues like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas]
PGD 0
Oops: 0000 [#1] SMP
CPU 1
Modules linked in: ses enclosure isci libsas scsi_transport_sas fuse sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf microcode pcspkr igb joydev iTCO_wdt ioatdma iTCO_vendor_support i2c_i801 i2c_core dca wmi hed ipv6 pata_acpi ata_generic [last unloaded: scsi_wait_scan]
Pid: 129, comm: kworker/u:3 Not tainted 3.3.0-rc5-isci+ #1 Intel Corporation SandyBridge Platform/To be filled by O.E.M.
RIP: 0010:[<ffffffffa011561b>] [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas]
RSP: 0018:ffff88042232dd70 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff8804283165b8 RCX: ffff88042232dda0
RDX: ffff88042232dd78 RSI: ffff8804283165b8 RDI: ffffffffa01188d7
RBP: ffff88042232ddd0 R08: ffff880388454000 R09: ffff8803edfde1f8
R10: ffff8803edfde1f8 R11: ffff8803edfde1f8 R12: ffff880428316750
R13: ffff880388454000 R14: ffff8803f88b31d0 R15: ffff8803f8b21d50
FS: 0000000000000000(0000) GS:ffff88042ee20000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000050 CR3: 0000000001a05000 CR4: 00000000000406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process kworker/u:3 (pid: 129, threadinfo ffff88042232c000, task ffff88042230c920)
Stack:
0000000000000000 ffff880400000018 ffff88042232dde0 ffff88042232dda0
ffffffffa01188c4 ffff88042ee93af0 ffff88042232ddb0 ffffffff8100e047
ffff88042232de10 ffff880420e5a2c8 ffff8803f8b21d50 ffff8803edfde1f8
Call Trace:
[<ffffffff8100e047>] ? load_TLS+0xb/0xf
[<ffffffffa01156ad>] async_sas_ata_eh+0x66/0x95 [libsas]
[<ffffffff810655e1>] async_run_entry_fn+0x9e/0x131
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Commit 899fcf4 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:
BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]
...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: Tom Jackson <thomas.p.jackson@intel.com>
Tested-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery. Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry. Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.
Fixes reports like:
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Pull networking fixes from David Miller:
1) Fix namespace init and cleanup in phonet to fix some oopses, from
Eric W. Biederman.
2) Missing kfree_skb() in AF_KEY, from Julia Lawall.
3) Refcount leak and source address handling fix in l2tp from James
Chapman.
4) Memory leak fix in CAIF from Tomasz Gregorek.
5) When routes are cloned from ipv6 addrconf routes, we don't process
expirations properly. Fix from Gao Feng.
6) Fix panic on DMA errors in atl1 driver, from Tony Zelenoff.
7) Only enable interrupts in 8139cp driver after we've registered the
IRQ handler. From Jason Wang.
8) Fix too many reads of KS_CIDER register in ks8851 during probe,
fixing crashes on spurious interrupts. From Matt Renzelmann.
9) Missing include in ath5k driver and missing iounmap on probe
failure, from Jonathan Bither.
10) Fix RX packet handling in smsc911x driver, from Will Deacon.
11) Fix ixgbe WoL on fiber by leaving the laser on during shutdown.
12) ks8851 needs MAX_RECV_FRAMES increased otherwise the internal MAC
buffers are easily overflown. Fix from Davide Cimingahi.
13) Fix memory leaks in peak_usb CAN driver, from Jesper Juhl.
14) gred packet scheduler can dump in WRED more when doing a netlink
dump. Fix from David Ward.
15) Fix MTU in USB smsc75xx driver, from Stephane Fillod.
16) Dummy device needs ->ndo_uninit handler to properly handle
->ndo_init failures. From Hiroaki SHIMODA.
17) Fix TX fragmentation in ath9k driver, from Sujith Manoharan.
18) Missing RTNL lock in ixgbe PM resume, from Benjamin Poirier.
19) Missing iounmap in farsync WAN driver, from Julia Lawall.
20) With LRO/GRO, tcp_grow_window() is easily tricked into not growing
the receive window properly, and this hurts performance. Fix from
Eric Dumazet.
21) Network namespace init failure can leak net_generic data, fix from
Julian Anastasov.
22) Fix skb_over_panic due to mis-accounting in TCP for partially ACK'd
SKBs. From Eric Dumazet.
23) New IDs for qmi_wwan driver, from Bjørn Mork.
24) Fix races in ax25_exit(), from Eric W. Biederman.
25) IPV6 TCP doesn't handle TCP_MAXSEG socket option properly, copy over
logic from the IPV4 side. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: fix TCP_MAXSEG for established IPv6 passive sockets
drivers/net: Do not free an IRQ if its request failed
drop_monitor: allow more events per second
ks8851: Fix request_irq/free_irq mismatch
net/hyperv: Adding cancellation to ensure rndis filter is closed
ks8851: Fix mutex deadlock in ks8851_net_stop()
net ax25: Reorder ax25_exit to remove races.
icplus: fix interrupt for IC+ 101A/G and 1001LF
net: qmi_wwan: support Sierra Wireless MC77xx devices in QMI mode
bnx2x: off by one in bnx2x_ets_e3b0_sp_pri_to_cos_set()
ksz884x: don't copy too much in netdev_set_mac_address()
tcp: fix retransmit of partially acked frames
netns: do not leak net_generic data on failed init
net/sock.h: fix sk_peek_off kernel-doc warning
tcp: fix tcp_grow_window() for large incoming frames
drivers/net/wan/farsync.c: add missing iounmap
davinci_mdio: Fix MDIO timeout check
ipv6: clean up rt6_clean_expires
ipv6: fix rt6_update_expires
arcnet: rimi: Fix device name in debug output
...
|
|
The following build warning is seen in some configurations.
drivers/hwmon/ad7314.c: In function 'ad7314_show_temperature':
drivers/hwmon/ad7314.c:70: warning: 'data' may be used uninitialized in this function
Fix by overloading the return value from ad7314_spi_read with both data and
error code (the returned data is really u16 and needs to be converted into a
signed value anyway).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Currently, during i2c works alone, wait-event timeout is not occurred.
However, as CPU load increases, timeout occurs frequently.
So, I modified like this patch.
Modifying like this patch, I've never seen the timeout event with high
load test.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
NACK interrupt is generated before I2C controller generates the STOP
condition on bus. Because of this reset of controller is happening
before I2C controller could complete STOP condition. So wait for some
time before resetting the controller so that STOP condition has
delivered properly on bus.
Added delay of 2 clock period before resetting the controller in case of
NACK error.
Signed-off-by: Alok Chauhan <alokc@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[wsa: Reworded the commit msg and code comment a bit]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
In the driver's suspend function, clk_enable() was used instead of
clk_disable(). This is corrected with this patch.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
CC: stable@vger.kernel.org
[wsa: reworded commit header slightly]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Use scsi_add_host_with_dma in ata_scsi_add_hosts to pass in the
correct DMA device(ATA host).
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.
Since commit d139b9b([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.
Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.
Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2
Reported-and-tested-by: Jörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
