summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-03-28nfp: validate the return code from dev_queue_xmit()Jakub Kicinski
dev_queue_xmit() may return error codes as well as netdev_tx_t, and it always consumes the skb. Make sure we always return a correct netdev_tx_t value. Fixes: eadfa4c3be99 ("nfp: add stats and xmit helpers for representors") Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: John Hurley <john.hurley@netronome.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28qmi_wwan: add Olicard 600Bjørn Mork
This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28Merge tag 'pci-v5.1-fixes-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci Pull PCI fixes from Bjorn Helgaas: "PCI fixes: - Clear level-triggered interrupts for the bandwidth notification supported added for v5.1 (Alexandru Gagniuc) - Clear bandwidth notification interrupts before enabling them (Lukas Wunner) - Report post-enumeration bandwidth changes only once for multi-function devices (Lukas Wunner)" * tag 'pci-v5.1-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: PCI/LINK: Deduplicate bandwidth reports for multi-function devices PCI/LINK: Clear bandwidth notification interrupt before enabling it PCI/LINK: Supply IRQ handler so level-triggered IRQs are acked
2019-03-28Merge branch '40GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue Jeff Kirsher says: ==================== Intel Wired LAN Driver Fixes 2019-03-26 This series contains updates to igb, ixgbe, i40e and fm10k. Jake fixes an issue with PTP in i40e where a previous commit resulted in a regression where the driver would interpret small negative adjustments as large positive additions, resulting in incorrect behavior. Arvind Sankar fixes an issue in igb where a previous commit would cause a warning in the PCI pm core and resulted in pci_pm_runtime_suspend would not call pci_save_state or pci_finish_runtime_suspend. Ivan Vecera fixes MDIO bus registration with ixgbe, where the driver was ignoring errors returned when registering and would leave the pointer in a NULL state which triggered a BUG when un-registering. Stefan Assmann fixes the check for Wake-On-LAN for i40e, which only supports magic packet. Yue Haibing fixes a potential NULL pointer de-reference in fm10k by adding a simple check if the value is NULL. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28nvmet: fix error flow during ns enableMax Gurtovoy
In case we fail to enable p2pmem on the current namespace, disable the backing store device before exiting. Cc: Stephen Bates <sbates@raithlin.com> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-03-28nvmet: fix building bvec from sg listMing Lei
There are two mistakes for building bvec from sg list for file backed ns: - use request data length to compute number of io vector, this way doesn't consider sg->offset, and the result may be smaller than required io vectors - bvec->bv_len isn't capped by sg->length This patch fixes this issue by building bvec from sg directly, given the whole IO stack is ready for multi-page bvec. Reported-by: Yi Zhang <yi.zhang@redhat.com> Fixes: 3a85a5de29ea ("nvme-loop: add a NVMe loopback host driver") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-03-28nvme-multipath: relax ANA state checkMartin George
When undergoing state transitions I/O might be requeued, hence we should always call nvme_mpath_set_live() to schedule requeue_work whenever the nvme device is live, independent on whether the old state was live or not. Signed-off-by: Martin George <marting@netapp.com> Signed-off-by: Gargi Srinivas <sring@netapp.com> Signed-off-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Christoph Hellwig <hch@lst.de>
2019-03-28nvme-tcp: fix an endianess miss-annotationChristoph Hellwig
nvme_tcp_end_request just takes the status value and the converts it to little endian as well as shifting for the phase bit. Fixes: 43ce38a6d823 ("nvme-tcp: support C2HData with SUCCESS flag") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
2019-03-28gpio: mockup: use simple_read_from_buffer() in debugfs read callbackBartosz Golaszewski
Calling read() for a single byte read will return 2 currently. Use simple_read_from_buffer() which correctly handles all sizes. Fixes: 2a9e27408e12 ("gpio: mockup: rework debugfs interface") Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2019-03-28gpio: of: Fix of_gpiochip_add() error pathGeert Uytterhoeven
If the call to of_gpiochip_scan_gpios() in of_gpiochip_add() fails, no error handling is performed. This lead to the need of callers to call of_gpiochip_remove() on failure, which causes "BAD of_node_put() on ..." if the failure happened before the call to of_node_get(). Fix this by adding proper error handling. Note that calling gpiochip_remove_pin_ranges() multiple times causes no harm: subsequent calls are a no-op. Fixes: dfbd379ba9b7431e ("gpio: of: Return error if gpio hog configuration failed") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Mukesh Ojha <mojha@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-03-28gpio: of: Check for "spi-cs-high" in child instead of parent nodeAndrey Smirnov
"spi-cs-high" is going to be specified in child node of an SPI controller's representing attached SPI device, so change the code to look for it there, instead of checking parent node. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-03-28gpio: of: Check propname before applying "cs-gpios" quirksAndrey Smirnov
SPI GPIO device has more than just "cs-gpio" property in its node and would request those GPIOs as a part of its initialization. To avoid applying CS-specific quirk to all of them add a check to make sure that propname is "cs-gpios". Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-gpio@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-03-28Merge tag 's390-5.1-2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 fixes from Martin Schwidefsky: "Improvements and bug fixes for 5.1-rc2: - Fix early free of the channel program in vfio - On AP device removal make sure that all messages are flushed with the driver still attached that queued the message - Limit brk randomization to 32MB to reduce the chance that the heap of ld.so is placed after the main stack - Add a rolling average for the steal time of a CPU, this will be needed for KVM to decide when to do busy waiting - Fix a warning in the CPU-MF code - Add a notification handler for AP configuration change to react faster to new AP devices" * tag 's390-5.1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390/cpumf: Fix warning from check_processor_id zcrypt: handle AP Info notification from CHSC SEI command vfio: ccw: only free cp on final interrupt s390/vtime: steal time exponential moving average s390/zcrypt: revisit ap device remove procedure s390: limit brk randomization to 32MB
2019-03-28Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Arnd Bergmann: "A couple of minor fixes only for now - fix for incorrect DMA channels on Renesas R-Car - Broadcom bcm2835 error handling fixes - Kconfig dependency fixes for bcm2835 and davinci - CPU idle wakeup fix for i.MX6 - MMC regression on Tegra186 - fix incorrect phy settings on one imx board" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: arm64: tegra: Disable CQE Support for SDMMC4 on Tegra186 ARM: dts: nomadik: Fix polarity of SPI CS ARM: davinci: fix build failure with allnoconfig ARM: imx_v4_v5_defconfig: enable PWM driver ARM: imx_v6_v7_defconfig: continue compiling the pwm driver ARM: dts: imx6dl-yapp4: Use correct pseudo PHY address for the switch ARM: dts: imx6qdl: Fix typo in imx6qdl-icore-rqs.dtsi ARM: dts: imx6ull: Use the correct style for SPDX License Identifier ARM: dts: pfla02: increase phy reset duration ARM: imx6q: cpuidle: fix bug that CPU might not wake up at expected time ARM: imx51: fix a leaked reference by adding missing of_node_put ARM: dts: imx6dl-yapp4: Use rgmii-id phy mode on the cpu port arm64: bcm2835: Add missing dependency on MFD_CORE. ARM: dts: bcm283x: Fix hdmi hpd gpio pull soc: bcm: bcm2835-pm: Fix error paths of initialization. soc: bcm: bcm2835-pm: Fix PM_IMAGE_PERI power domain support. arm64: dts: renesas: r8a774c0: Fix SCIF5 DMA channels arm64: dts: renesas: r8a77990: Fix SCIF5 DMA channels
2019-03-28libata: fix using DMA buffers on stackraymond pang
When CONFIG_VMAP_STACK=y, __pa() returns incorrect physical address for a stack virtual address. Stack DMA buffers must be avoided. Signed-off-by: raymond pang <raymondpangxd@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2019-03-28drm/i915/icl: Fix VEBOX mismatch BUG_ON()José Roberto de Souza
GT VEBOX DISABLE is only 4 bits wide but it was using a 8 bits wide mask, the remaning reserved bits is set to 0 causing 4 more nonexistent VEBOX engines being detected as enabled, triggering the BUG_ON() because of mismatch between vebox_mask and newly added VEBOX_MASK(). [ 64.081621] [drm:intel_device_info_init_mmio [i915]] vdbox enable: 0005, instances: 0005 [ 64.081763] [drm:intel_device_info_init_mmio [i915]] vebox enable: 00f1, instances: 0001 [ 64.081825] intel_device_info_init_mmio:925 GEM_BUG_ON(vebox_mask != ({ unsigned int first__ = (VECS0); unsigned int count__ = (2); ((&(dev_priv)->__info)->engine_mask & (((~0UL) - (1UL << (first__)) + 1) & (~0UL >> (64 - 1 - (first__ + count__ - 1))))) >> first__; })) [ 64.082047] ------------[ cut here ]------------ [ 64.082054] kernel BUG at drivers/gpu/drm/i915/intel_device_info.c:925! BSpec: 20680 Fixes: 26376a7e74d2 ("drm/i915/icl: Check for fused-off VDBOX and VEBOX instances") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Cc: Oscar Mateo <oscar.mateo@intel.com> Signed-off-by: José Roberto de Souza <jose.souza@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190326230223.26336-1-jose.souza@intel.com (cherry picked from commit 547fcf9b1c608cf5c43c156a8773a94c6a38dc44) Signed-off-by: Jani Nikula <jani.nikula@intel.com>
2019-03-28mmc: alcor: don't write data before command has completedDaniel Drake
The alcor driver is setting up data transfer and submitting the associated MMC command at the same time. While this works most of the time, it occasionally causes problems upon write. In the working case, after setting up the data transfer and submitting the MMC command, an interrupt comes in a moment later with CMD_END and WRITE_BUF_RDY bits set. The data transfer then happens without problem. However, on occasion, the interrupt that arrives at that point only has WRITE_BUF_RDY set. The hardware notifies that it's ready to write data, but the associated MMC command is still running. Regardless, the driver was proceeding to write data immediately, and that would then cause another interrupt indicating data CRC error, and the write would fail. Additionally, the transfer setup function alcor_trigger_data_transfer() was being called 3 times for each write operation, which was confusing and may be contributing to this issue. Solve this by tweaking the driver behaviour to follow the sequence observed in the original ampe_stor vendor driver: 1. When starting request handling, write 0 to DATA_XFER_CTRL 2. Submit the command 3. Wait for CMD_END interrupt and then trigger data transfer 4. For the PIO case, trigger the next step of the data transfer only upon the following DATA_END interrupt, which occurs after the block has been written. I confirmed that the read path still works (DMA & PIO) and also now presents more consistency with the operations performed by ampe_stor. Signed-off-by: Daniel Drake <drake@endlessm.com> Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2019-03-28cpufreq: scpi: Fix use after freeVincent Stehlé
Free the priv structure only after we are done using it. Fixes: 1690d8bb91e370ab ("cpufreq: scpi/scmi: Fix freeing of dynamic OPPs") Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Cc: 4.20+ <stable@vger.kernel.org> # 4.20+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-28ACPICA: Clear status of GPEs before enabling themFurquan Shaikh
Commit 18996f2db918 ("ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume") was added to stop clearing event status bits unconditionally in the system-wide suspend and resume paths. This was done because of an issue with a laptop lid appaering to be closed even when it was used to wake up the system from suspend (see https://bugzilla.kernel.org/show_bug.cgi?id=196249), which happened because event status bits were cleared unconditionally on system resume. Though this change fixed the issue in the resume path, it introduced regressions in a few suspend paths. First regression was reported and fixed in the S5 entry path by commit fa85015c0d95 ("ACPICA: Clear status of all events when entering S5"). Next regression was reported and fixed for all legacy sleep paths by commit f317c7dc12b7 ("ACPICA: Clear status of all events when entering sleep states"). However, there still is a suspend-to-idle regression, since suspend-to-idle does not follow the legacy sleep paths. In the suspend-to-idle case, wakeup is enabled as part of device suspend. If the status bits of wakeup GPEs are set when they are enabled, it causes a premature system wakeup to occur. To address that problem, partially revert commit 18996f2db918 to restore GPE status bits clearing before the GPE is enabled in acpi_ev_enable_gpe(). Fixes: 18996f2db918 ("ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume") Signed-off-by: Furquan Shaikh <furquan@google.com> Cc: 4.17+ <stable@vger.kernel.org> # 4.17+ [ rjw: Subject & changelog ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2019-03-28USB: serial: option: add Olicard 600Bjørn Mork
This is a Qualcomm based device with a QMI function on interface 4. It is mode switched from 2020:2030 using a standard eject message. T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2020 ProdID=2031 Rev= 2.32 S: Manufacturer=Mobile Connect S: Product=Mobile Connect S: SerialNumber=0123456789ABCDEF C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none) E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us Cc: stable@vger.kernel.org Signed-off-by: Bjørn Mork <bjorn@mork.no> [ johan: use tabs to align comments in adjacent lines ] Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-28USB: serial: cp210x: add new device idGreg Kroah-Hartman
Lorenz Messtechnik has a device that is controlled by the cp210x driver, so add the device id to the driver. The device id was provided by Silicon-Labs for the devices from this vendor. Reported-by: Uli <t9cpu@web.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2019-03-27vrf: prevent adding upper devicesSabrina Dubroca
VRF devices don't work with upper devices. Currently, it's possible to add a VRF device to a bridge or team, and to create macvlan, macsec, or ipvlan devices on top of a VRF (bond and vlan are prevented respectively by the lack of an ndo_set_mac_address op and the NETIF_F_VLAN_CHALLENGED feature flag). Fix this by setting the IFF_NO_RX_HANDLER flag (introduced in commit f5426250a6ec ("net: introduce IFF_NO_RX_HANDLER")). Cc: David Ahern <dsahern@gmail.com> Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-28crypto: caam - fix copy of next buffer for xcbc and cmacIuliana Prodan
Fix a side effect of adding xcbc support, when the next_buffer is not copied. The issue occurs, when there is stored from previous state a blocksize buffer and received, a less than blocksize, from user. In this case, the nents for req->src is 0, and the next_buffer is not copied. An example is: { .tap = { 17, 15, 8 }, .psize = 40, .np = 3, .ksize = 16, } Fixes: 12b8567f6fa4 ("crypto: caam - add support for xcbc(aes)") Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2019-03-27thunderx: eliminate extra calls to put_page() for pages held for recyclingDean Nelson
For the non-XDP case, commit 773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP") added code to nicvf_free_rbdr() that, when releasing the additional receive buffer page reference held for recycling, repeatedly calls put_page() until the page's _refcount goes to zero. Which results in the page being freed. This is not okay if the page's _refcount was greater than 1 (in the non-XDP case), because nicvf_free_rbdr() should not be subtracting more than what nicvf_alloc_page() had previously added to the page's _refcount, which was only 1 (in the non-XDP case). This can arise if a received packet is still being processed and the receive buffer (i.e., skb->head) has not yet been freed via skb_free_head() when nicvf_free_rbdr() is spinning through the aforementioned put_page() loop. If this should occur, when the received packet finishes processing and skb_free_head() is called, various problems can ensue. Exactly what, depends on whether the page has already been reallocated or not, anything from "BUG: Bad page state ... ", to "Unable to handle kernel NULL pointer dereference ..." or "Unable to handle kernel paging request...". So this patch changes nicvf_free_rbdr() to only call put_page() once for pages held for recycling (in the non-XDP case). Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP") Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27thunderx: enable page recycling for non-XDP caseDean Nelson
Commit 773225388dae15e72790 ("net: thunderx: Optimize page recycling for XDP") added code to nicvf_alloc_page() that inadvertently disables receive buffer page recycling for the non-XDP case by always NULL'ng the page pointer. This patch corrects two if-conditionals to allow for the recycling of non-XDP mode pages by only setting the page pointer to NULL when the page is not ready for recycling. Fixes: 773225388dae ("net: thunderx: Optimize page recycling for XDP") Signed-off-by: Dean Nelson <dnelson@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27net: hns3: fix compile errorXi Wang
Currently, the rules for configuring search paths in Kbuild have changed, this will lead some erros when compiling hns3 with the following command: make O=DIR M=drivers/net/ethernet/hisilicon/hns3 drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.c:11:10: fatal error: hnae3.h: No such file or directory This patch fix it by adding $(srctree)/ prefix to the serach paths. Signed-off-by: Xi Wang <wangxi11@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27net: dsa: mv88e6xxx: fix few issues in mv88e6390x_port_set_cmodeHeiner Kallweit
This patches fixes few issues in mv88e6390x_port_set_cmode(). 1. When entering the function the old cmode may be 0, in this case mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail out and have no chance to set a new mode. Therefore deal properly with -ENODEV. 2. Once we have disabled power and irq, let's set the cached cmode to 0. This reflects the actual status and is cleaner if we bail out with an error in the following function calls. 3. The cached cmode is used by mv88e6390x_serdes_get_lane(), mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable(). Currently we set the cached mode to the new one at the very end of the function only, means until then we use the old one what may be wrong. 4. When calling mv88e6390_serdes_irq_enable() we use the lane value belonging to the old cmode. Get the lane belonging to the new cmode before calling this function. It's hard to provide a good "Fixes" tag because quite a few smaller changes have been done to the code in question recently. Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-03-27drm/amd/display: VBIOS can't be light up HDMI when restart systemPaul Hsieh
[Why] VBIOS will not post pixel rate > 340MHz. If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't post HDMI monitor due to monitor is stay in HDMI2.0 state. [How] Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream. Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Acked-by: Harry Wentland <Harry.Wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-03-27drm/amd/powerplay: fix possible hang with 3+ 4K monitorsEvan Quan
If DAL requires to force MCLK high, the FCLK will be forced to high also. Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-03-27drm/amd/powerplay: correct data type to avoid overflowEvan Quan
Avoid left shift overflow. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-03-27drm/amd/powerplay: add ECC feature bitEvan Quan
It's OK to have this feature bit with old SMU firmwares. But the feature should be disabled on them. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-03-27drm/amd/amdgpu: fix PCIe dpm feature issue (v3)Chengming Gui
use pcie_bandwidth_available to get real link state to update pcie table. v2: fix incorrect initialized return value v3: expand the fetching method about the link width to all asics. Signed-off-by: Chengming Gui <Jack.Gui@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2019-03-27scsi: ibmvfc: Clean up transport eventsTyrel Datwyler
No change to functionality. Simply make transport event messages a little clearer, and rework CRQ format enums such that we have separate enums for INIT messages and XPORT events. [mkp: typo] Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: ibmvfc: Byte swap status and error codes when loggingTyrel Datwyler
Status and error codes are returned in big endian from the VIOS. The values are translated into a human readable format when logged, but the values are also logged. This patch byte swaps those values so that they are consistent between BE and LE platforms. Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: ibmvfc: Add failed PRLI to cmd_status lookup arrayTyrel Datwyler
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status and 0x8000 error code. Add these codes to cmd_status[] with appropriate human readable error message. Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: ibmvfc: Remove "failed" from logged errorsTyrel Datwyler
The text of messages logged with ibmvfc_log_error() always contain the term "failed". In the case of cancelled commands during EH they are reported back by the VIOS using error codes. This can be confusing to somebody looking at these log messages as to whether a command was successfully cancelled. The following real log message for example it is unclear if the transaction was actaully cancelled. <6>sd 0:0:1:1: Cancelling outstanding commands. <3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0 Remove prefixing of "failed" to all error logged messages. The ibmvfc_log_error() function translates the returned error/status codes to a human readable message already. Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: zfcp: reduce flood of fcrscn1 trace records on multi-element RSCNSteffen Maier
If an incoming ELS of type RSCN contains more than one element, zfcp suboptimally causes repeated erp trigger NOP trace records for each previously failed port. These could be ports that went away. It loops over each RSCN element, and for each of those in an inner loop over all zfcp_ports. The trigger to recover failed ports should be just the reception of some RSCN, no matter how many elements it has. So we can loop over failed ports separately, and only then loop over each RSCN element to handle the non-failed ports. The call chain was: zfcp_fc_incoming_rscn for (i = 1; i < no_entries; i++) _zfcp_fc_incoming_rscn list_for_each_entry(port, &adapter->port_list, list) if (masked port->d_id match) zfcp_fc_test_link if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <=== In order the reduce the "flooding" of the REC trace area in such cases, we factor out handling the failed ports to be outside of the entries loop: zfcp_fc_incoming_rscn if (no_entries > 1) <=== list_for_each_entry(port, &adapter->port_list, list) <=== if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <=== for (i = 1; i < no_entries; i++) _zfcp_fc_incoming_rscn list_for_each_entry(port, &adapter->port_list, list) if (masked port->d_id match) zfcp_fc_test_link Abbreviated example trace records before this code change: Tag : fcrscn1 WWPN : 0x500507630310d327 ERP want : 0x02 ERP need : 0x02 Tag : fcrscn1 WWPN : 0x500507630310d327 ERP want : 0x02 ERP need : 0x00 NOP => superfluous trace record The last trace entry repeats if there are more than 2 RSCN elements. Signed-off-by: Steffen Maier <maier@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Jens Remus <jremus@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: zfcp: fix scsi_eh host reset with port_forced ERP for non-NPIV FCP devicesSteffen Maier
Suppose more than one non-NPIV FCP device is active on the same channel. Send I/O to storage and have some of the pending I/O run into a SCSI command timeout, e.g. due to bit errors on the fibre. Now the error situation stops. However, we saw FCP requests continue to timeout in the channel. The abort will be successful, but the subsequent TUR fails. Scsi_eh starts. The LUN reset fails. The target reset fails. The host reset only did an FCP device recovery. However, for non-NPIV FCP devices, this does not close and reopen ports on the SAN-side if other non-NPIV FCP device(s) share the same open ports. In order to resolve the continuing FCP request timeouts, we need to explicitly close and reopen ports on the SAN-side. This was missing since the beginning of zfcp in v2.6.0 history commit ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter."). Note: The FSF requests for forced port reopen could run into FSF request timeouts due to other reasons. This would trigger an internal FCP device recovery. Pending forced port reopen recoveries would get dismissed. So some ports might not get fully reopened during this host reset handler. However, subsequent I/O would trigger the above described escalation and eventually all ports would be forced reopen to resolve any continuing FCP request timeouts due to earlier bit errors. Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: <stable@vger.kernel.org> #3.0+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: zfcp: fix rport unblock if deleted SCSI devices on Scsi_HostSteffen Maier
An already deleted SCSI device can exist on the Scsi_Host and remain there because something still holds a reference. A new SCSI device with the same H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When we try to unblock an rport, we still find the deleted SCSI device and return early because the zfcp_scsi_dev of that SCSI device is not ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if the new proper SCSI device would be in good state. Therefore, skip deleted SCSI devices when iterating the sdevs of the shost. [cf. __scsi_device_lookup{_by_target}() or scsi_device_get()] The following abbreviated trace sequence can indicate such problem: Area : REC Tag : ersfs_3 LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED Ready count : n not incremented yet Running count : 0x00000000 ERP want : 0x01 ERP need : 0xc1 ZFCP_ERP_ACTION_NONE Area : REC Tag : ersfs_3 LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x41000000 Ready count : n+1 Running count : 0x00000000 ERP want : 0x01 ERP need : 0x01 ... Area : REC Level : 4 only with increased trace level Tag : ertru_l LUN : 0x4045400300000000 WWPN : 0x50050763031bd327 LUN status : 0x40000000 Request ID : 0x0000000000000000 ERP status : 0x01800000 ERP step : 0x1000 ERP action : 0x01 ERP count : 0x00 NOT followed by a trace record with tag "scpaddy" for WWPN 0x50050763031bd327. Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery") Cc: <stable@vger.kernel.org> #2.6.32+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: sd: Quiesce warning if device does not report optimal I/O sizeMartin K. Petersen
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size") split one conditional into several separate statements in an effort to provide more accurate warning messages when a device reports a nonsensical value. However, this reorganization accidentally dropped the precondition of the reported value being larger than zero. This lead to a warning getting emitted on devices that do not report an optimal I/O size at all. Remain silent if a device does not report an optimal I/O size. Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size") Cc: Randy Dunlap <rdunlap@infradead.org> Cc: <stable@vger.kernel.org> Reported-by: Hussam Al-Tayeb <ht990332@gmx.com> Tested-by: Hussam Al-Tayeb <ht990332@gmx.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: sd: Fix a race between closing an sd device and sd I/OBart Van Assche
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and hence needs the disk->private_data pointer. Avoid that that pointer is cleared before all affected I/O requests have finished. This patch avoids that the following crash occurs: Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: scsi_mq_uninit_cmd+0x1c/0x30 scsi_end_request+0x7c/0x1b8 scsi_io_completion+0x464/0x668 scsi_finish_command+0xbc/0x160 scsi_eh_flush_done_q+0x10c/0x170 sas_scsi_recover_host+0x84c/0xa98 [libsas] scsi_error_handler+0x140/0x5b0 kthread+0x100/0x12c ret_from_fork+0x10/0x18 Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Jason Yan <yanaijie@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reported-by: Jason Yan <yanaijie@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27scsi: core: Run queue when state is set to running after being blockedzhengbin
Use dd to test a SCSI device: 1. echo "blocked" >/sys/block/sda/device/state 2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10 3. echo "running" >/sys/block/sda/device/state dd should finish this work after step 3, but it hangs. After step2, the call chain is this: blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will transition it to BLK_STS_DEV_RESOURCE which means that driver can guarantee that IO dispatch will be triggered in future when the resource is available. Need to follow the rule if we set the device state to running. [mkp: tweaked commit description and code comment as suggested by Bart] Signed-off-by: zhengbin <zhengbin13@huawei.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-03-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: "Fixes here and there, a couple new device IDs, as usual: 1) Fix BQL race in dpaa2-eth driver, from Ioana Ciornei. 2) Fix 64-bit division in iwlwifi, from Arnd Bergmann. 3) Fix documentation for some eBPF helpers, from Quentin Monnet. 4) Some UAPI bpf header sync with tools, also from Quentin Monnet. 5) Set descriptor ownership bit at the right time for jumbo frames in stmmac driver, from Aaro Koskinen. 6) Set IFF_UP properly in tun driver, from Eric Dumazet. 7) Fix load/store doubleword instruction generation in powerpc eBPF JIT, from Naveen N. Rao. 8) nla_nest_start() return value checks all over, from Kangjie Lu. 9) Fix asoc_id handling in SCTP after the SCTP_*_ASSOC changes this merge window. From Marcelo Ricardo Leitner and Xin Long. 10) Fix memory corruption with large MTUs in stmmac, from Aaro Koskinen. 11) Do not use ipv4 header for ipv6 flows in TCP and DCCP, from Eric Dumazet. 12) Fix topology subscription cancellation in tipc, from Erik Hugne. 13) Memory leak in genetlink error path, from Yue Haibing. 14) Valid control actions properly in packet scheduler, from Davide Caratti. 15) Even if we get EEXIST, we still need to rehash if a shrink was delayed. From Herbert Xu. 16) Fix interrupt mask handling in interrupt handler of r8169, from Heiner Kallweit. 17) Fix leak in ehea driver, from Wen Yang" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (168 commits) dpaa2-eth: fix race condition with bql frame accounting chelsio: use BUG() instead of BUG_ON(1) net: devlink: skip info_get op call if it is not defined in dumpit net: phy: bcm54xx: Encode link speed and activity into LEDs tipc: change to check tipc_own_id to return in tipc_net_stop net: usb: aqc111: Extend HWID table by QNAP device net: sched: Kconfig: update reference link for PIE net: dsa: qca8k: extend slave-bus implementations net: dsa: qca8k: remove leftover phy accessors dt-bindings: net: dsa: qca8k: support internal mdio-bus dt-bindings: net: dsa: qca8k: fix example net: phy: don't clear BMCR in genphy_soft_reset bpf, libbpf: clarify bump in libbpf version info bpf, libbpf: fix version info and add it to shared object rxrpc: avoid clang -Wuninitialized warning tipc: tipc clang warning net: sched: fix cleanup NULL pointer exception in act_mirr r8169: fix cable re-plugging issue net: ethernet: ti: fix possible object reference leak net: ibm: fix possible object reference leak ...
2019-03-27IB/mlx5: Reset access mask when looping inside page fault handlerMoni Shoua
If page-fault handler spans multiple MRs then the access mask needs to be reset before each MR handling or otherwise write access will be granted to mapped pages instead of read-only. Cc: <stable@vger.kernel.org> # 3.19 Fixes: 7bdf65d411c1 ("IB/mlx5: Handle page faults") Reported-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2019-03-27IB/hfi1: Fix the allocation of RSM tableKaike Wan
The receive side mapping (RSM) on hfi1 hardware is a special matching mechanism to direct an incoming packet to a given hardware receive context. It has 4 instances of matching capabilities (RSM0 - RSM3) that share the same RSM table (RMT). The RMT has a total of 256 entries, each of which points to a receive context. Currently, three instances of RSM have been used: 1. RSM0 by QOS; 2. RSM1 by PSM FECN; 3. RSM2 by VNIC. Each RSM instance should reserve enough entries in RMT to function properly. Since both PSM and VNIC could allocate any receive context between dd->first_dyn_alloc_ctxt and dd->num_rcv_contexts, PSM FECN must reserve enough RMT entries to cover the entire receive context index range (dd->num_rcv_contexts - dd->first_dyn_alloc_ctxt) instead of only the user receive contexts allocated for PSM (dd->num_user_contexts). Consequently, the sizing of dd->num_user_contexts in set_up_context_variables is incorrect. Fixes: 2280740f01ae ("IB/hfi1: Virtual Network Interface Controller (VNIC) HW support") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2019-03-27IB/hfi1: Eliminate opcode tests on mr derefKaike Wan
When an old ack_queue entry is used to store an incoming request, it may need to clean up the old entry if it is still referencing the MR. Originally only RDMA READ request needed to reference MR on the responder side and therefore the opcode was tested when cleaning up the old entry. The introduction of tid rdma specific operations in the ack_queue makes the specific opcode tests wrong. Multiple opcodes (RDMA READ, TID RDMA READ, and TID RDMA WRITE) may need MR ref cleanup. Remove the opcode specific tests associated with the ack_queue. Fixes: f48ad614c100 ("IB/hfi1: Move driver out of staging") Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2019-03-27IB/hfi1: Clear the IOWAIT pending bits when QP is put into error stateKaike Wan
When a QP is put into error state, it may be waiting for send engine resources. In this case, the QP will be removed from the send engine's waiting list, but its IOWAIT pending bits are not cleared. This will normally not have any major impact as the QP is being destroyed. However, the QP still needs to wind down its operations, such as draining the send queue by scheduling the send engine. Clearing the pending bits will avoid any potential complications. In addition, if the QP will eventually hang, clearing the pending bits can help debugging by presenting a consistent picture if the user dumps the qp_stats. This patch clears a QP's IOWAIT_PENDING_IB and IO_PENDING_TID bits in priv->s_iowait.flags in this case. Fixes: 5da0fc9dbf89 ("IB/hfi1: Prepare resource waits for dual leg") Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Alex Estrin <alex.estrin@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2019-03-27IB/hfi1: Failed to drain send queue when QP is put into error stateKaike Wan
When a QP is put into error state, all pending requests in the send work queue should be drained. The following sequence of events could lead to a failure, causing a request to hang: (1) The QP builds a packet and tries to send through SDMA engine. However, PIO engine is still busy. Consequently, this packet is put on the QP's tx list and the QP is put on the PIO waiting list. The field qp->s_flags is set with HFI1_S_WAIT_PIO_DRAIN; (2) The QP is put into error state by the user application and notify_error_qp() is called, which removes the QP from the PIO waiting list and the packet from the QP's tx list. In addition, qp->s_flags is cleared of RVT_S_ANY_WAIT_IO bits, which does not include HFI1_S_WAIT_PIO_DRAIN bit; (3) The hfi1_schdule_send() function is called to drain the QP's send queue. Subsequently, hfi1_do_send() is called. Since the flag bit HFI1_S_WAIT_PIO_DRAIN is set in qp->s_flags, hfi1_send_ok() fails. As a result, hfi1_do_send() bails out without draining any request from the send queue; (4) The PIO engine completes the sending and tries to wake up any QP on its waiting list. But the QP has been removed from the PIO waiting list and therefore is kept in sleep forever. The fix is to clear qp->s_flags of HFI1_S_ANY_WAIT_IO bits in step (2). HFI1_S_ANY_WAIT_IO includes RVT_S_ANY_WAIT_IO and HFI1_S_WAIT_PIO_DRAIN. Fixes: 2e2ba09e48b7 ("IB/rdmavt, IB/hfi1: Create device dependent s_flags") Cc: <stable@vger.kernel.org> # 4.19.x+ Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Alex Estrin <alex.estrin@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2019-03-27libnvdimm/btt: Fix a kmemdup failure checkAditya Pakki
In case kmemdup fails, the fix releases resources and returns to avoid the NULL pointer dereference. Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2019-03-28virt: vbox: Implement passing requestor info to the host for VirtualBox 6.0.xHans de Goede
VirtualBox 6.0.x has a new feature where the guest kernel driver passes info about the origin of the request (e.g. userspace or kernelspace) to the hypervisor. If we do not pass this information then when running the 6.0.x userspace guest-additions tools on a 6.0.x host, some requests will get denied with a VERR_VERSION_MISMATCH error, breaking vboxservice.service and the mounting of shared folders marked to be auto-mounted. This commit implements passing the requestor info to the host, fixing this. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-09-12 02:37:02 +0000