| Age | Commit message (Collapse) | Author |
|---|
|
This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM core fix for incorrect double bio splitting. Keep "fixing" this
because past attempts didn't fully appreciate the liability relative
to recursive bio splitting. This fix limits DM's bio splitting to a
single method and does _not_ use blk_queue_split() for normal IO.
- DM crypt Documentation updates for features added during 5.9 merge.
* tag 'for-5.9/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: document encrypted keyring key option
dm crypt: document new no_workqueue flags
dm: fix comment in dm_process_bio()
dm: fix bio splitting and its bio completion order for regular IO
|
|
In the function nvme_get_effects_log() it uses NVME_NSID_ALL which has
namespace scope. The command effect log page is controller specific.
Replace NVME_NSID_ALL with 0x00 which specifies the controller scope
instead of namespace scope.
Fixes: 84fef62d135b ("nvme: check admin passthru command effects")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209287
Reported-by: Huai-Cheng Kuo <hh81478072@gmail.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
spi_unregister_controller() not only unregisters the controller, but
also frees the controller. This will free the driver data with it, so
we must not access it later dspi_remove().
Solve this by allocating the driver data separately from the SPI
controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200923131026.20707-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently we wrongly set the mask of value of LDO2/4 both to the mask of
LDO2, and the LDO4 voltage configuration is left untouched. This leads
to conflict when LDO2/4 are both in use.
Fix this issue by setting different vsel_mask to both regulators.
Fixes: db4a555f7c4c ("regulator: axp20x: use defines for masks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20200923005142.147135-1-icenowy@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the lapic_timer_needs_broadcast() stub for
ARCH_APICTIMER_STOPS_ON_C3 unset to actually return
a value.
Fixes: aa6b43d57f99 ("ACPI: processor: Use CPUIDLE_FLAG_TIMER_STOP")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since we store a pointer to the fake iommu device that is allocated on
the stack, as soon as we leave the function it goes out of scope and any
future dereference is undefined behaviour. Just in case we may need to
look at the fake iommu device after initialiation, move the allocation
from the stack into the data.
Fixes: 01b9d4e21148 ("iommu/vt-d: Use dev_iommu_priv_get/set()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916105022.28316-2-chris@chris-wilson.co.uk
(cherry picked from commit 9f9f4101fc98db56714e71676d5a1e2d27e01f7e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This error path needs to call clk_disable_unprepare().
Fixes: 7296443b900e ("PM / devfreq: tegra30: Handle possible round-rate error")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The commit 4dc3bab8687f ("PM / devfreq: Add support delayed timer for
polling mode") supports the delayed timer but this commit missed
the adding the timer type to devfreq_summary debugfs node.
Add the timer type to devfreq_summary debugfs.
Fixes: 4dc3bab8687f ("PM / devfreq: Add support delayed timer for polling mode")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.9-rc6:
- Fill asoc card owner in vc4.
- Program secondary CSC correctly in sun4i, and extend
register mapping to cover secondary CSC registers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e3ab56cf-3b8e-9b21-f1b6-9a4989a52996@linux.intel.com
|
|
transport_lookup_tmr_lun() uses "orig_fe_lun" member of struct se_cmd for
the lookup. Hence, update this field directly for the
TARGET_SCF_LOOKUP_LUN_FROM_TAG case.
Link: https://lore.kernel.org/r/1600300471-26135-1-git-send-email-sudhakar.panneerselvam@oracle.com
Fixes: a36840d80027 ("target: Initialize LUN in transport_init_se_cmd()")
Reported-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
|
|
The fixed divider the emac_ptp_free_clk should be 2, not 4.
Fixes: 07afb8db7340 ("clk: socfpga: stratix10: add clock driver for
Stratix10 platform")
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200831202657.8224-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-fixes
Pull Tegra clk driver fixes from Thierry Reding:
This is a set of small fixes for the Tegra clock driver.
* tag 'for-5.10-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Fix missing prototype for tegra210_clk_register_emc()
clk: tegra: Always program PLL_E when enabled
clk: tegra: Capitalization fixes
|
|
The commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path"), moved the calls rcu_idle_enter|exit() into the cpuidle core.
However, it forgot to remove a couple of comments in enter_s2idle_proper()
about why RCU_NONIDLE earlier was needed. So, let's drop them as they have
become a bit misleading.
Fixes: 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the idle path")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2020-09-17
- Fix kernel oops for VFIO edid on BDW (Zhenyu)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917064208.GF11592@zhen-hp.sh.intel.com
|
|
commit 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Initializing the nvme hwmon retrieves a log from the controller. If the
controller is broken, we need to return the appropriate error so that
subsequent initialization doesn't attempt to continue.
Reported-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Andy reported that commit 6b41030fdc79 ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Remove superfluous '.c' from qcom-spmi-adc5 device driver name.
Fixes: e13d757279bb ("iio: adc: Add QCOM SPMI PMIC5 ADC driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200910140000.324091-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Returning errno is a bug, fix that.
Also fixes smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/en/port.c:453
mlx5e_fec_in_caps() warn: signedness bug returning '(-95)'
Fixes: 2132b71f78d2 ("net/mlx5e: Advertise globaly supported FEC modes")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
|
|
The spinlock only needed when accessing the channel's icosq, grab the lock
after the buf allocation in resync_post_get_progress_params() to avoid
kzalloc(GFP_KERNEL) in atomic context.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Resync progress params buffer and dma weren't released on error,
Add missing error unwinding for resync_post_get_progress_params().
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Progress params dma address is never unmapped, unmap it when completion
handling is over.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
|
|
Using synchronize_rcu() is sufficient to wait until running NAPI quits.
See similar upstream fix with detailed explanation:
("net/mlx5e: Use synchronize_rcu to sync with NAPI")
This change also fixes a possible use-after-free as the NAPI
might be already released at this stage.
Fixes: 0419d8c9d8f8 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The set of TLS TX global SW counters in mlx5e_tls_sw_stats_desc
is updated from all rings by using atomic ops.
This set of stats is used only in the FPGA TLS use case, not in
the Connect-X TLS one, where regular per-ring counters are used.
Do not expose them in the Connect-X use case, as this would cause
counter duplication. For example, tx_tls_drop_no_sync_data would
appear twice in the ethtool stats.
Fixes: d2ead1f360e8 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".
Fix it to work with the correct group by extracting it from the caller's
profile.
Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.
Fixes: 8a236b15144b ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.
Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".
Fixes: f62b8bb8f2d3 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.
Fixes: 88f30bbcbaaa ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.
Fix by adding FW capability check before creating peer groups/rule.
Fixes: ac004b832128 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add missing mapping remove call when removing ct rule,
as the mapping was allocated when ct rule was adding with ct_label.
Also there is a missing mapping remove call in error flow.
Fixes: 54b154ecfb8c ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When deleting vxlan flow rule under multipath, tun_info in parse_attr is
not freed when the rule is not ready.
Fixes: ef06c9ee8933 ("net/mlx5e: Allow one failure when offloading tc encap rules under multipath")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
As described in the previous commit, napi_synchronize doesn't quite fit
the purpose when we just need to wait until the currently running NAPI
quits. Its implementation waits until NAPI is not running by polling and
waiting for 1ms in between. In cases where we need to deactivate one
queue (e.g., recovery flows) or where we deactivate them one-by-one
(deactivate channel flow), we may get stuck in napi_synchronize forever
if other queues keep NAPI active, causing a soft lockup. Depending on
kernel configuration (CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC), it may result
in a kernel panic.
To fix the issue, use synchronize_rcu to wait for NAPI to quit, and wrap
the whole NAPI in rcu_read_lock.
Fixes: acc6c5953af1 ("net/mlx5e: Split open/close channels to stages")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, the RQs are temporarily deactivated while hot-replacing the
XDP program, and napi_synchronize is used to make sure rq->xdp_prog is
not in use. However, napi_synchronize is not ideal: instead of waiting
till the end of a NAPI cycle, it polls and waits until NAPI is not
running, sleeping for 1ms between the periodic checks. Under heavy
workloads, this loop will never end, which may even lead to a kernel
panic if the kernel detects the hangup. Such workloads include XSK TX
and possibly also heavy RX (XSK or normal).
The fix is inspired by commit 326fe02d1ed6 ("net/mlx4_en: protect
ring->xdp_prog with rcu_read_lock"). As mlx5e_xdp_handle is already
protected by rcu_read_lock, and bpf_prog_put uses call_rcu to free the
program, there is no need for additional synchronization if proper RCU
functions are used to access the pointer. This patch converts all
accesses to rq->xdp_prog to use RCU functions.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Fixes: db05815b36cb ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, when an FTE is allocated, its refcount is decreased to 0
with the purpose it will not be a stand alone steering object and every
rule (destination) of the FTE would increase the refcount.
When mlx5_cleanup_fs is called while not all rules were deleted by the
steering users, it hit refcount underflow on the FTE once clean_tree
calls to tree_remove_node after the deleted rules already decreased
the refcount to 0.
FTE is no longer destroyed implicitly when the last rule (destination)
is deleted. mlx5_del_flow_rules avoids it by increasing the refcount on
the FTE and destroy it explicitly after all rules were deleted. So we
can avoid the refcount underflow by making FTE as stand alone object.
In addition need to set del_hw_func to FTE so the HW object will be
destroyed when the FTE is deleted from the cleanup_tree flow.
refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 15715 at lib/refcount.c:28 refcount_warn_saturate+0xd9/0xe0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
tree_put_node+0xf2/0x140 [mlx5_core]
clean_tree+0x4e/0xf0 [mlx5_core]
clean_tree+0x4e/0xf0 [mlx5_core]
clean_tree+0x4e/0xf0 [mlx5_core]
clean_tree+0x5f/0xf0 [mlx5_core]
clean_tree+0x4e/0xf0 [mlx5_core]
clean_tree+0x5f/0xf0 [mlx5_core]
mlx5_cleanup_fs+0x26/0x270 [mlx5_core]
mlx5_unload+0x2e/0xa0 [mlx5_core]
mlx5_unload_one+0x51/0x120 [mlx5_core]
mlx5_devlink_reload_down+0x51/0x90 [mlx5_core]
devlink_reload+0x39/0x120
? devlink_nl_cmd_reload+0x43/0x220
genl_rcv_msg+0x1e4/0x420
? genl_family_rcv_msg_attrs_parse+0x100/0x100
netlink_rcv_skb+0x47/0x110
genl_rcv+0x24/0x40
netlink_unicast+0x217/0x2f0
netlink_sendmsg+0x30f/0x430
sock_sendmsg+0x30/0x40
__sys_sendto+0x10e/0x140
? handle_mm_fault+0xc4/0x1f0
? do_page_fault+0x33f/0x630
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x48/0x130
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 718ce4d601db ("net/mlx5: Consolidate update FTE for all removal changes")
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Refer to the correct function (->submit_bio instead of ->queue_bio).
Also, add details about why using blk_queue_split() isn't needed for
dm_wq_work()'s call to dm_process_bio().
Fixes: c62b37d96b6eb ("block: move ->make_request_fn to struct block_device_operations")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
dm_queue_split() is removed because __split_and_process_bio() _must_
handle splitting bios to ensure proper bio submission and completion
ordering as a bio is split.
Otherwise, multiple recursive calls to ->submit_bio will cause multiple
split bios to be allocated from the same ->bio_split mempool at the same
time. This would result in deadlock in low memory conditions because no
progress could be made (only one bio is available in ->bio_split
mempool).
This fix has been verified to still fix the loss of performance, due
to excess splitting, that commit 120c9257f5f1 provided.
Fixes: 120c9257f5f1 ("Revert "dm: always call blk_queue_split() in dm_process_bio()"")
Cc: stable@vger.kernel.org # 5.0+, requires custom backport due to 5.9 changes
Reported-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.9-rc6
- fix the interrupt configuration in gpio-tc35894
- explicitly support only threaded irqs in gpio-siox
- fix a resource leak in error path in gpio-mockup
- fix line event handling in syscall compatible mode in GPIO chardev
|
|
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This failure path should return a negative error code but it currently
returns success.
Fixes: 51b35a454efd ("sfc: skeleton EF100 PF driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPIE register contains counts for the TX FIFO so any time the irq
handler was invoked we would attempt to process the RX/TX fifos. Use the
SPIM value to mask the events so that we only process interrupts that
were expected.
This was a latent issue exposed by commit 3282a3da25bd ("powerpc/64:
Implement soft interrupt replay in C").
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20200904002812.7300-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Non-incrementing writes can fail if register + length crosses page
border. However for non-incrementing writes we should not check for page
border crossing. Fix this by passing additional flag to _regmap_raw_write
and passing length to _regmap_select_page basing on the flag.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: cdf6b11daa77 ("regmap: Add regmap_noinc_write API")
Link: https://lore.kernel.org/r/20200917153405.3139200-2-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
