| Age | Commit message (Collapse) | Author |
|---|
|
This patch disables tunnel offloads via ndo_features_check()
if given UDP port is not offloaded to hardware. This in turn
allows to run multiple tunnel interfaces using different UDP ports.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the tunnel APIs to use per tunnel
info instead of using bitmasks for all tunnels and also
uses single struct to hold the data to prepare multiple
variant of tunnel configuration ramrods to be sent to the hardware.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add driver for the regulator block in the ROHM BD9571MWV-W MFD PMIC.
This block supports three voltage monitors, VD18, VD25, VD33 for the
1V8, 2V5, 3V3 voltage rails and a single voltage regulator for the
DVFS rail.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch implements consideration of the SPI_READY mode flag as
defined in spi.h. It extends the device tree bindings to support
the values defined by the reference manual for the DRCTL field.
Thus supporting edge-triggered and level-triggered bursts.
Signed-off-by: Leif Middelschulte <Leif.Middelschulte@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for sharing this driver with Madera codecs, factor out
the parts of initialization that aren't dependent on struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for supporting Madera codecs, remove the dependency on
struct arizona in the regulator callbacks and struct arizona_ldo1.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for sharing this driver with Madera, move the pdata
for the LDO1 regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_ldo1_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for sharing this driver with Madera codecs, factor out
the parts of initialization that aren't dependent on struct arizona.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for supporting Madera codecs, remove the dependency on
struct arizona in the regulator callbacks and struct arizona_micsupp.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In preparation for sharing this driver with Madera, move the pdata
for the micsupp regulator out of struct arizona_pdata into a dedicated
pdata struct for this driver. As a result the code in
arizona_micsupp_of_get_pdata() can be made independent of struct arizona.
This patch also updates the definition of struct arizona_pdata and
the use of this pdata in mach-crag6410-module.c
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The CS47L24 Arizona codec and most Madera codecs do not have a LDO1
regulator. Split the LDO1 and MICSUPP regulators into separate KConfig
options so the LDO1 is only built into the kernel if needed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 4.11-rc1
|
|
In functions team_nl_send_port_list_get() and
team_nl_send_options_get(), pointer skb keeps the return value of
nlmsg_new(). When the call to genlmsg_put() fails, the memory is not
freed(). This will result in memory leak bugs.
Fixes: 9b00cf2d1024 ("team: implement multipart netlink messages for options transfers")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-04-25
this is a pull request of three patches for net/master.
There are two patches by Stephane Grosjean for that add a new variant to the
PCAN-Chip USB driver. The other patch is by Maksim Salau, which swtiches the
memory for USB transfers from heap to stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: dd248f1bc65b ("sfc: Add PCI ID for Solarflare 8000 series 10/40G NIC")
Reported-by: Patrick Talbert <ptalbert@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-04-25
this is a pull request of 21 patches for net-next/master.
There are 4 patches by Stephane Grosjean for the PEAK PCAN-PCIe FD
CAN-FD boards. The next 7 patches are by Mario Huettel, which add
support for M_CAN IP version >= v3.1.x to the m_can driver. A patch by
Remigiusz Kołłątaj adds support for the Microchip CAN BUS Analyzer. 8
patches by Oliver Hartkopp complete the initial CAN network namespace
support. Wei Yongjun's patch for the ti_hecc driver fixes the return
value check in the probe function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 4fbae7d83c98c30efc ("ipvlan: Introduce l3s mode") added
registration of netfilter hooks via nf_register_hooks().
This API provides the illusion of 'global' netfilter hooks by placing the
hooks in all current and future network namespaces.
In case of ipvlan the hook appears to be only needed in the namespace
that contains the ipvlan master device (i.e., usually init_net), so
placing them in all namespaces is not needed.
This switches ipvlan driver to pernet operations, and then only registers
hooks in namespaces where a ipvlan master device is set to l3s mode.
Extra care has to be taken when the master device is moved to another
namespace, as we might have to 'move' the netfilter hooks too.
This is done by storing the namespace the ipvlan port was created in.
On REGISTER event, do (un)register operations in the old/new namespaces.
This will also allow removal of the nf_register_hooks() in a future patch.
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb48c ("macvlan: Fix potential use-after free for...")
Reported-by: Joe Ghalam <Joe.Ghalam@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for the PL-27A1 by adding the appropriate
USB ID's. This chip is used in the goobay Active USB 3.0 Data Link
and Unitek Y-3501 cables.
Signed-off-by: Roman Spychała <roed@onet.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In iwl_mvm_sar_get_ewrd_table() In case of a BIOS bug, n_profiles
might be 0 thus we need to return an error value. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Delete the scanned channel results.
No need in it we get it any way when logging.
The print only clogs up the ftrace print buffer.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
From code "SMR mask 0x%x out of range for SMMU", so, we need to use mask, not
sid.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Add a comment clarifying that NAND subpage write on keystone works,
but is not being enabled in the interest of backward compatibility.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
commit c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
of_device_id tables should be NULL terminated.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We accidentally return 1 on error instead of proper error codes.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some NAND controllers are using DMA engine requiring a specific
buffer alignment. The core provides no guarantee on the nand_buffers
pointers, which forces some drivers to allocate their own buffers
and pass the NAND_OWN_BUFFERS flag.
Rework the nand_buffers allocation logic to allocate each buffer
independently. This should make most NAND controllers/DMA engine
happy, and allow us to get rid of these custom buf allocation in
NAND controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 271707b1d817 ("mtd: nand: denali: max_banks calculation
changed in revision 5.1") added a revision check to support the
new max_banks encoding. Its git-log states "The encoding of
max_banks changed in Denali revision 5.1".
There are exceptional cases, for example, the revision register on
some UniPhier SoCs says the IP is 5.0 but the max_banks is encoded
in the new format.
This IP updates the resister specification from time to time (often
breaking the backward compatibility), but the revision number is not
incremented correctly.
The max_banks is not only the case that needs revision checking.
Let's allow to override an incorrect revision number.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
"pdev" is much more often used to point a platform_device, so this
will help the driver code look consistent across the kernel.
While we are here, fix "line over 80 characters" coding style
violations.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The current driver only supports the DMA engine up to 32 bit
physical address, but there also exists 64 bit capable DMA engine
for this IP.
The data DMA setup sequence is completely different, so I added the
64 bit DMA code as a new function denali_setup_dma64(). The 32 bit
one has been renamed to denali_setup_dma32().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some old versions of the Denali IP (perhaps used only for Intel?)
detects ECC errors and provides correct data via a register, but
does not touch the transferred data. So, the software must fixup
the data in the buffer according to the provided ECC correction
information.
Newer versions perform ECC correction before transferring the data.
No more software intervention is needed. The ECC_ERROR_ADDRESS and
ECC_CORRECTION_INFO registers were deprecated. Instead, the number
of corrected bit-flips are reported via the ECC_COR_INFO register.
When an uncorrectable ECC error happens, a status flag is set to the
INTR_STATUS and ECC_COR_INFO registers.
As is often the case with this IP, the register view of INTR_STATUS
had broken compatibility.
For older versions (SW ECC fixup):
bit 0: ECC_TRANSACTION_DONE
bit 1: ECC_ERR
For newer versions (HW ECC fixup):
bit 0: ECC_UNCOR_ERR
bit 1: Reserved
Due to this difference, the irq_mask must be fixed too.
The existing handle_ecc() has been renamed to denali_sw_ecc_fixup()
for clarification.
What is unfortunate with this feature is we can not know the total
number of corrected/uncorrected errors in a page. The register
ECC_COR_INFO reports the maximum of per-sector bitflips. This is
useful for ->read_page return value, but ecc_stats.{corrected,failed}
increments may not be precise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This part is wrong in multiple ways:
[1] is_erased() is called against "buf" twice, so the OOB area is
not checked at all. The second call should check chip->oob_poi.
[2] This code block is nested by double "if (check_erase_page)".
The inner one is redundant.
[3] The ECC_ERROR_ADDRESS register reports which sector(s) had
uncorrectable ECC errors. It is pointless to check the whole page
if only one sector contains errors.
[4] Unfortunately, the Denali ECC correction engine has already
manipulated the data buffer before it decides the bitflips are
uncorrectable. That is, not all of the data are 0xFF after an
erased page is processed by the ECC engine. The current is_erased()
helper could report false-positive ECC errors. Actually, a certain
mount of bitflips are allowed in an erased page. The core framework
provides nand_check_erased_ecc_chunk() that takes the threshold into
account. Let's use this.
This commit reworks the code to solve those problems.
Please note the erased page checking is implemented as a separate
helper function instead of embedding it in the loop in handle_ecc().
The reason is that OOB data are needed for the erased page checking,
but the controller can not start a new transaction until all ECC
error information is read out from the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This function is wrong in multiple ways:
[1] Counting corrected bytes instead of corrected bits.
The following code is counting the number of corrected _bytes_.
/* correct the ECC error */
buf[offset] ^= err_cor_value;
mtd->ecc_stats.corrected++;
bitflips++;
What the core framework expects is the number of corrected _bits_.
They can be different if multiple bitflips occur within one byte.
[2] total number of errors instead of max of per-sector errors
The core framework expects that corrected errors are counted per
sector, then the max value should be taken. The current code simply
iterates over the whole page, i.e. counts the total number of
correction in the page. This means "too many bitflips" is triggered
earlier than it should be, i.e. the NAND device is worn out sooner.
Besides those bugs, this function is unreadable due to the deep
nesting. Notice the whole code in this function is wrapped in
if (irq_status & INTR__ECC_ERR), so this conditional can be moved
out of the function. Also, use shorter names for local variables.
Re-work the function to fix all the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The pipeline read-ahead function of the Denali IP enables continuous
reading from the device; while data is being read out by a CPU, the
controller maintains additional commands for streaming data from the
device. This will reduce the latency of the second page or later.
This feature is obviously no help for per-page accessors of Linux
NAND driver interface.
In the current implementation, the pipeline command is issued to
load a single page, then data are read out immediately. The use of
the pipeline operation is not adding any advantage, but just adding
complexity to the code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 28309572aac4 ("mtd: name the mtd device with an optional
label property") allow us to identify a chip in a user-friendly way.
If nand_set_flash_node() picks up the "label" from DT, let's respect
it. Otherwise, let it fallback to the current name "denali-nand".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
|
|
While freeing inactive queue, check mvmsta to be valid before
dereferencing it. Found by Klocwork.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Tested on HP Elite X2 1012 G1.
Matches event report of Lenovo Helix 2
(https://www.spinics.net/lists/ibm-acpi-devel/msg03982.html).
Signed-off-by: Maarten Maathuis <madman2003@shikahr.net>
[andy: fixed indentation of comments and massaged title of the change]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
There's no need to have iwl_run_unified_mvm_ucode() be exposed
to other parts of the code since the logic to pick it over the
normal code in iwl_run_init_mvm_ucode() can just be done in
that function itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Rates were changed to adapt to HE. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Allocate buffers on HEAP instead of STACK for local structures
that are to be sent using usb_control_msg().
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.8
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
devm_gpiod_get_optional() can return -ENOSYS if GPIOLIB is
disabled, causing probe to fail. Warn the user if this
happens.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This patch adds a text line in the help section of the CAN_PEAK_USB
config item describing the support of the PCAN-USB X6 adapter, which is
already included in the Kernel since 4.9.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
