summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-10-02bus: mhi: Remove unused nr_irqs_req variableLoic Poulain
nr_irqs_req is unused in MHI stack. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-18-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Allow shared IRQ for event ringsLoic Poulain
There is no requirement for using a dedicated IRQ per event ring. Some systems does not support multiple MSI vectors (e.g. intel without CONFIG_IRQ_REMAP), In that case the MHI controller can configure all the event rings to use the same interrupt (as fallback). Allow this by removing the nr_irqs = ev_ring test and add extra check in the irq_setup function. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-17-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Introduce sysfs entries for MHIBhaumik Bhatt
Introduce sysfs entries to enable userspace clients the ability to read the serial number and the OEM PK Hash values obtained from BHI. OEMs need to read these device-specific hardware information values through userspace for factory testing purposes and cannot be exposed via degbufs as it may remain disabled for performance reasons. Also, update the documentation for ABI to include these entries. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> [mani: used dev_groups to manage sysfs attributes] Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-16-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Introduce debugfs entries for MHIBhaumik Bhatt
Introduce debugfs entries to show state, register, channel, device, and event rings information. Allow the host to dump registers, issue device wake, and change the MHI timeout to help in debug. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-15-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: Fix entries based on Kconfig coding styleBhaumik Bhatt
Kconfig coding style mandates use of tabs for the configuration definition and an additional two spaces for the help text. Make the required changes to the MHI Kconfig adhering to those guidelines. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-14-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Add const qualifier to MHI config informationHemant Kumar
MHI channel, event and controller config data needs to be treated read only information. Add const qualifier to make sure config information passed by MHI controller is not modified by MHI core driver. Suggested-by: Kalle Valo <kvalo@codeaurora.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Hemant Kumar <hemantk@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-12-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Introduce APIs to allocate and free the MHI controllerBhaumik Bhatt
Client devices should use the APIs provided to allocate and free the MHI controller structure. This will help ensure that the structure is zero-initialized and there are no false positives with respect to reading any values such as the serial number or the OEM PK hash. Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-11-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Read and save device hardware information from BHIBhaumik Bhatt
Device hardware specific information such as serial number and the OEM PK hash can be read using BHI and saved on host to identify the endpoint. Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-10-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Introduce counters to track MHI device state transitionsBhaumik Bhatt
Use counters to track MHI device state transitions such as those to M0, M2, or M3 states. This can help in better debug, allowing the user to see the number of transitions to a certain MHI state when queried using debugfs entries or via other mechanisms. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-9-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Introduce helper function to check device stateBhaumik Bhatt
Introduce a helper function to determine whether the device is in a powered ON state and resides in one of the active MHI states. This will allow for some use cases where access can be pre-determined. Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-8-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Use generic name field for an MHI deviceBhaumik Bhatt
An MHI device is not necessarily associated with only channels as we can have one associated with the controller itself. Hence, the chan_name field within the mhi_device structure should instead be replaced with a generic name to accurately reflect any type of MHI device. Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-7-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Trigger host resume if suspended during mhi_device_get()Bhaumik Bhatt
It is possible that the host may be suspending or suspended and may not allow an outgoing device wake assert immediately if a client has requested for it. Ensure that the host wakes up and allows for it so the client does not have to wait for an external trigger or an outgoing packet to be queued for the host resume to occur. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-6-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Use helper API to trigger a non-blocking host resumeBhaumik Bhatt
Autonomous low power mode support requires the MHI host to resume from multiple places and post a wakeup source to exit system suspend. This needs to be done in a non-blocking manner. Introduce a helper API to trigger the host resume for data transfers and other non-blocking use cases while supporting implementation of autonomous low power modes. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-5-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Abort suspends due to outgoing pending packetsBhaumik Bhatt
Add the missing check to abort suspends if a client driver has pending outgoing packets to send to the device. This allows better utilization of the MHI bus wherein clients on the host are not left waiting for longer suspend or resume cycles to finish for data transfers. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-4-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02bus: mhi: core: Remove double occurrence for mhi_ctrl_ev_task() declarationBhaumik Bhatt
mhi_ctrl_ev_task() in the internal header file occurred twice. Remove one of the occurrences for clean-up. Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20200929175218.8178-3-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02USB: cdc-wdm: Make wdm_flush() interruptible and add wdm_fsync().Oliver Neukum
syzbot is reporting hung task at wdm_flush() [1], for there is a circular dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget cannot be called unless close() for /dev/cdc-wdm0 completes. Tetsuo Handa considered that such circular dependency is an usage error [2] which corresponds to an unresponding broken hardware [3]. But Alan Stern responded that we should be prepared for such hardware [4]. Therefore, this patch changes wdm_flush() to use wait_event_interruptible_timeout() which gives up after 30 seconds, for hardware that remains silent must be ignored. The 30 seconds are coming out of thin air. Changing wait_event() to wait_event_interruptible_timeout() makes error reporting from close() syscall less reliable. To compensate it, this patch also implements wdm_fsync() which does not use timeout. Those who want to be very sure that data has gone out to the device are now advised to call fsync(), with a caveat that fsync() can return -EINVAL when running on older kernels which do not implement wdm_fsync(). This patch also fixes three more problems (listed below) found during exhaustive discussion and testing. Since multiple threads can concurrently call wdm_write()/wdm_flush(), we need to use wake_up_all() whenever clearing WDM_IN_USE in order to make sure that all waiters are woken up. Also, error reporting needs to use fetch-and-clear approach in order not to report same error for multiple times. Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well check WDM_DISCONNECTING. In wdm_flush(), since locks are not held, it is not safe to dereference desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus, remove dev_err() from wdm_flush(). [1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186 [2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp [3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp [4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu [5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com> Cc: stable <stable@vger.kernel.org> Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02net: pegasus: Use the new usb control message API.Petko Manolov
The old usb_control_msg() let the caller handle the error and also did not account for partial reads. Since these are now considered harmful, move the driver over to usb_control_msg_recv/send() calls. Added small note about why set_registers() can't be used to substitute set_register(). Signed-off-by: Petko Manolov <petko.manolov@konsulko.com> Acked-by: David S. Miller <davem@davemloft.net> Link: https://lore.kernel.org/r/20200927124909.16380-2-petko.manolov@konsulko.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02net: rtl8150: Use the new usb control message API.Petko Manolov
The old usb_control_msg() let the caller handle the error and also did not account for partial reads. Since these are now considered harmful, move the driver over to usb_control_msg_recv/send() calls. Signed-off-by: Petko Manolov <petko.manolov@konsulko.com> Acked-by: David S. Miller <davem@davemloft.net> Link: https://lore.kernel.org/r/20200927124909.16380-3-petko.manolov@konsulko.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02usb: typec: displayport: Reduce noise from the driverHeikki Krogerus
It's not an error if the mode can't be entered because another mode is already active, so no longer printing an error message if that happens. Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02USB: hub: Add Kconfig option to reduce number of port initialization retriesAlan Stern
Description based on one by Yasushi Asano: According to 6.7.22 A-UUT “Device No Response” for connection timeout of USB OTG and EH automated compliance plan v1.2, enumeration failure has to be detected within 30 seconds. However, the old and new enumeration schemes each make a total of 12 attempts, and each attempt can take 5 seconds to time out, so the PET test fails. This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES); when the option is set all the initialization retry loops except the outermost are reduced to a single iteration. This reduces the total number of attempts to four, allowing Linux hosts to pass the PET test. The new option is disabled by default to preserve the existing behavior. The reduced number of retries may fail to initialize a few devices that currently do work, but for the most part there should be no change. And in cases where the initialization does fail, it will fail much more quickly. Reported-and-tested-by: yasushi asano <yazzep@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02USB: hub: Clean up use of port initialization schemes and retriesAlan Stern
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the number of port-initialization retry attempts rather than the number of Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and use_new_scheme() function are written in a very confusing manner, making it almost impossible to figure out exactly what they do or check that they are correct. This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more transparent, with added comments explaining how it works. The patch also pulls the single call site of use_new_scheme() out from the Get-Descriptor retry loop (where it returns the same value each time) and renames the local variable used to store the result. The overall effect is a minor cleanup. However, there is one functional change: If the "use_both_schemes" module parameter isn't set (by default it is set), the existing code does only two retry iterations. After this patch it will always perform four, regardless of the parameter's value. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-02efi: mokvar: add missing include of asm/early_ioremap.hArd Biesheuvel
Nathan reports that building the new mokvar table code for 32-bit ARM fails with errors such as error: implicit declaration of function 'early_memunmap' error: implicit declaration of function 'early_memremap' This is caused by the lack of an explicit #include of the appropriate header, and ARM apparently does not inherit that inclusion via another header file. So add the #include. Tested-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
2020-10-02crypto: atmel-tdes - use semicolons rather than commas to separate statementsJulia Lawall
Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: drivers - use semicolons rather than commas to separate statementsJulia Lawall
Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02hwrng: mxc-rnga - use semicolons rather than commas to separate statementsJulia Lawall
Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02hwrng: iproc-rng200 - use semicolons rather than commas to separate statementsJulia Lawall
Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02hwrng: stm32 - use semicolons rather than commas to separate statementsJulia Lawall
Replace commas with semicolons. What is done is essentially described by the following Coccinelle semantic patch (http://coccinelle.lip6.fr/): // <smpl> @@ expression e1,e2; @@ e1 -, +; e2 ... when any // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: hisilicon/zip - fix the uninitalized 'curr_qm_qp_num'Sihang Chen
The 'qm->curr_qm_qp_num' is not initialized, which will result in failure to write the current_q file. Signed-off-by: Sihang Chen <chensihang1@hisilicon.com> Signed-off-by: Yang Shen <shenyang39@huawei.com> Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: hisilicon/zip - fix the return value when device is busyYang Shen
As before, when the ZIP device is too busy to creat a request, it will return '-EBUSY'. But the crypto process think the '-EBUSY' means a successful request and wait for its completion. So replace '-EBUSY' with '-EAGAIN' to show crypto this request is failed. Fixes: 62c455ca853e("crypto: hisilicon - add HiSilicon ZIP...") Signed-off-by: Yang Shen <shenyang39@huawei.com> Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: hisilicon/zip - fix zero length input in GZIP decompressZhou Wang
The zero length input will cause a call trace when use GZIP decompress like this: Unable to handle kernel paging request at virtual address ... lr : get_gzip_head_size+0x7c/0xd0 [hisi_zip] Judge the input length and return '-EINVAL' when input is invalid. Fixes: 62c455ca853e("crypto: hisilicon - add HiSilicon ZIP...") Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Yang Shen <shenyang39@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: hisilicon/zip - fix the uncleared debug registersHao Fang
ZIP debug registers aren't cleared even if its driver is removed, so add a clearing operation when remove driver. Signed-off-by: Hao Fang <fanghao11@huawei.com> Signed-off-by: Yang Shen <shenyang39@huawei.com> Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02hwrng: npcm - modify readl to readbTomer Maimon
Modify the read size to the correct HW random registers size, 8bit. The incorrect read size caused and faulty HW random value. Signed-off-by: Tomer Maimon <tmaimon77@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: sa2ul - Fix DMA mapping API usagePeter Ujfalusi
Make sure that we call the dma_unmap_sg on the correct scatterlist on completion with the correct sg_nents. Use sg_table to managed the DMA mapping and at the same time add the needed dma_sync calls for the sg_table. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi2 - add support for XTS with 16B IVAndrei Botila
Newer CAAM versions (Era 9+) support 16B IVs. Since for these devices the HW limitation is no longer present newer version should process the requests containing 16B IVs directly in hardware without using a fallback. Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi - add support for XTS with 16B IVAndrei Botila
Newer CAAM versions (Era 9+) support 16B IVs. Since for these devices the HW limitation is no longer present newer version should process the requests containing 16B IVs directly in hardware without using a fallback. Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/jr - add support for XTS with 16B IVAndrei Botila
Newer CAAM versions (Era 9+) support 16B IVs. Since for these devices the HW limitation is no longer present newer version should process the requests containing 16B IVs directly in hardware without using a fallback. Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam - add xts check for block length equal to zeroAndrei Botila
XTS should not return succes when dealing with block length equal to zero. This is different than the rest of the skcipher algorithms. Fixes: 31bb2f0da1b50 ("crypto: caam - check zero-length input") Cc: <stable@vger.kernel.org> # v5.4+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi2 - add support for more XTS key lengthsAndrei Botila
CAAM accelerator only supports XTS-AES-128 and XTS-AES-256 since it adheres strictly to the standard. All the other key lengths are accepted and processed through a fallback as long as they pass the xts_verify_key() checks. Fixes: 226853ac3ebe ("crypto: caam/qi2 - add skcipher algorithms") Cc: <stable@vger.kernel.org> # v4.20+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi - add support for more XTS key lengthsAndrei Botila
CAAM accelerator only supports XTS-AES-128 and XTS-AES-256 since it adheres strictly to the standard. All the other key lengths are accepted and processed through a fallback as long as they pass the xts_verify_key() checks. Fixes: b189817cf789 ("crypto: caam/qi - add ablkcipher and authenc algorithms") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/jr - add support for more XTS key lengthsAndrei Botila
CAAM accelerator only supports XTS-AES-128 and XTS-AES-256 since it adheres strictly to the standard. All the other key lengths are accepted and processed through a fallback as long as they pass the xts_verify_key() checks. Fixes: c6415a6016bf ("crypto: caam - add support for acipher xts(aes)") Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi2 - add fallback for XTS with more than 8B IVAndrei Botila
A hardware limitation exists for CAAM until Era 9 which restricts the accelerator to IVs with only 8 bytes. When CAAM has a lower era a fallback is necessary to process 16 bytes IV. Fixes: 226853ac3ebe ("crypto: caam/qi2 - add skcipher algorithms") Cc: <stable@vger.kernel.org> # v4.20+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/qi - add fallback for XTS with more than 8B IVAndrei Botila
A hardware limitation exists for CAAM until Era 9 which restricts the accelerator to IVs with only 8 bytes. When CAAM has a lower era a fallback is necessary to process 16 bytes IV. Fixes: b189817cf789 ("crypto: caam/qi - add ablkcipher and authenc algorithms") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: caam/jr - add fallback for XTS with more than 8B IVAndrei Botila
A hardware limitation exists for CAAM until Era 9 which restricts the accelerator to IVs with only 8 bytes. When CAAM has a lower era a fallback is necessary to process 16 bytes IV. Fixes: c6415a6016bf ("crypto: caam - add support for acipher xts(aes)") Cc: <stable@vger.kernel.org> # v4.4+ Signed-off-by: Andrei Botila <andrei.botila@nxp.com> Reviewed-by: Horia Geantă <horia.geanta@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: mediatek - simplify the return expression of mtk_dfe_dse_reset()Qinglang Miao
Simplify the return expression. Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: marvell/octeontx - simplify the return expression of ↵Qinglang Miao
create_sysfs_eng_grps_info() Simplify the return expression. Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: ccp - fix error handlingPavel Machek
Fix resource leak in error handling. Signed-off-by: Pavel Machek (CIP) <pavel@denx.de> Acked-by: John Allen <john.allen@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02crypto: cpt - simplify the return expression of cav_register_algsLiu Shixin
Simplify the return expression. Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2020-10-02mtd: parsers: bcm63xx: Do not make it modularFlorian Fainelli
With commit 91e81150d388 ("mtd: parsers: bcm63xx: simplify CFE detection"), we generate a reference to fw_arg3 which is the fourth firmware/command line argument on MIPS platforms. That symbol is not exported and would cause a linking failure. The parser is typically necessary to boot a BCM63xx-based system anyway so having it be part of the kernel image makes sense, therefore make it 'bool' instead of 'tristate'. Fixes: 91e81150d388 ("mtd: parsers: bcm63xx: simplify CFE detection") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200929172726.30469-1-f.fainelli@gmail.com
2020-10-02mtd: spear_smi: Enable compile testingMiquel Raynal
This driver does not contain any architecture specific code, enable compile testing it. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200928155715.14370-1-miquel.raynal@bootlin.com
2020-10-02mtd: maps: vmu-flash: fix typos for struct memcardBernard Zhao
Change struct memcard`s element "removeable" -> "removable". Signed-off-by: Bernard Zhao <bernard@vivo.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20200922112814.26761-1-bernard@vivo.com
generated by cgit (git 2.34.1) at 2025-09-19 14:15:50 +0000