| Age | Commit message (Collapse) | Author |
|---|
|
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e94
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This partially reverts commit 4aea7a5c5e940c1723add439f4088844cd26196d.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e94 ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc33 ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e94 ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
On Gen11 interrupt masks need to be clear to allow C6 entry.
We keep them all enabled knowing that we generate extra
interrupts.
v2: Rebase.
v3: Remove gen 11 extra check in logical_render_ring_init.
v4: Rebase fixes.
v5: Rebase/refactor.
v6: Rebase.
v7: Rebase.
v8: Update comment and commit message (Daniele)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302161501.28594-1-mika.kuoppala@linux.intel.com
|
|
The readl_poll_timeout() return value is 0 in case of success
so it is better to detect errors without taking care of the
return value sign.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180204213624.18288-1-philippe.cornu@st.com
|
|
drivers/media/Kconfig: typo: replace `with` with `which`
Signed-off-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
If a start bit is detected, then reset the receive buffer counter to 0.
This ensures that no stale data is in the buffer if a message is
broken off midstream due to e.g. a Low Drive condition and then
retransmitted.
The only Rx interrupts we need to listen to are RX_REGISTER_FULL (i.e.
a valid byte was received) and RX_START_BIT_DETECTED (i.e. a new
message starts and we need to reset the counter).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.15 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
If we fail to acquire a fence when we must, we must unwind before
reporting the error. Otherwise, we lose tracking of the vma pinning and
eventually hit a bug like
<3>[ 46.163202] i915_vma_unpin:333 GEM_BUG_ON(!i915_vma_is_pinned(vma))
<4>[ 46.163424] ------------[ cut here ]------------
<2>[ 46.163429] kernel BUG at drivers/gpu/drm/i915/i915_vma.h:333!
<4>[ 46.163444] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
<0>[ 46.163451] Dumping ftrace buffer:
<0>[ 46.163457] ---------------------------------
<0>[ 46.163630] <...>-84 1.... 46260767us : i915_gem_object_unpin_from_display_plane: i915_vma_unpin:333 GEM_BUG_ON(!i915_vma_is_pinned(vma))
<0>[ 46.163635] ---------------------------------
<4>[ 46.163638] Modules linked in: vgem i915 snd_hda_codec_analog snd_hda_codec_generic coretemp snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm lpc_ich mei_me e1000e mei prime_numbers
<4>[ 46.163667] CPU: 1 PID: 84 Comm: kworker/u16:1 Tainted: G U 4.16.0-rc3-gc07ef2c77d14-kasan_18+ #1
<4>[ 46.163671] Hardware name: Dell Inc. OptiPlex 755 /0PU052, BIOS A08 02/19/2008
<4>[ 46.163743] Workqueue: events_unbound intel_atomic_commit_work [i915]
<4>[ 46.163809] RIP: 0010:i915_gem_object_unpin_from_display_plane+0x253/0x2f0 [i915]
<4>[ 46.163813] RSP: 0018:ffff8800624cfb48 EFLAGS: 00010286
<4>[ 46.163818] RAX: 000000000000000c RBX: ffff880064446c40 RCX: ffff8800653135b8
<4>[ 46.163822] RDX: dffffc0000000000 RSI: 0000000000000054 RDI: ffff8800651e30d0
<4>[ 46.163825] RBP: 00000000000003d0 R08: 0000000000000001 R09: ffff8800651e3158
<4>[ 46.163829] R10: 0000000000000000 R11: ffff8800651e30f0 R12: 0000000000000001
<4>[ 46.163832] R13: ffff880054c58620 R14: 0000000000000000 R15: dffffc0000000000
<4>[ 46.163836] FS: 0000000000000000(0000) GS:ffff880066040000(0000) knlGS:0000000000000000
<4>[ 46.163840] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
<4>[ 46.163843] CR2: 00007f1fc6fb0000 CR3: 00000000526fe000 CR4: 00000000000006e0
<4>[ 46.163846] Call Trace:
<4>[ 46.163918] intel_unpin_fb_vma+0xbd/0x300 [i915]
<4>[ 46.163990] intel_cleanup_plane_fb+0x99/0xc0 [i915]
<4>[ 46.163998] drm_atomic_helper_cleanup_planes+0x166/0x280
<4>[ 46.164071] intel_atomic_commit_tail+0x1594/0x33a0 [i915]
<4>[ 46.164081] ? process_one_work+0x66e/0x1460
<4>[ 46.164151] ? skl_update_crtcs+0x9c0/0x9c0 [i915]
<4>[ 46.164157] ? lock_acquire+0x13d/0x390
<4>[ 46.164161] ? lock_acquire+0x13d/0x390
<4>[ 46.164169] process_one_work+0x71a/0x1460
<4>[ 46.164175] ? __schedule+0x838/0x1e50
<4>[ 46.164182] ? pwq_dec_nr_in_flight+0x2b0/0x2b0
<4>[ 46.164188] ? _raw_spin_lock_irq+0xa/0x40
<4>[ 46.164194] worker_thread+0xdf/0xf60
<4>[ 46.164204] ? process_one_work+0x1460/0x1460
<4>[ 46.164209] kthread+0x2cf/0x3c0
<4>[ 46.164213] ? _kthread_create_on_node+0xa0/0xa0
<4>[ 46.164218] ret_from_fork+0x3a/0x50
<4>[ 46.164227] Code: e8 78 d9 cd e8 48 8b 35 cc 9e 47 00 49 c7 c0 c0 31 84 c0 b9 4d 01 00 00 48 c7 c2 e0 80 84 c0 48 c7 c7 0e bb 57 c0 e8 5d 4b df e8 <0f> 0b 48 c7 c1 c0 30 84 c0 ba 4e 01 00 00 48 c7 c6 e0 80 84 c0
<1>[ 46.164368] RIP: i915_gem_object_unpin_from_display_plane+0x253/0x2f0 [i915] RSP: ffff8800624cfb48
Fixes: 85798ac9b35f ("drm/i915: Fail if we can't get a fence for gen2/3 tiled scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305103312.29492-1-chris@chris-wilson.co.uk
|
|
Platforms before Gen11 were sharing lanes between port-A & port-E.
This limitation is no more there.
Changes since V1:
- optimize the code (Shashank/Jani)
- create helper function to get max lanes (ville)
Changes since V2:
- Include BIOS fail fix-up in same helper function (ville)
Changes since V3:
- remove confusing if/else (jani)
- group intel_encoder initialization
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206060855.30026-1-mahesh1.kumar@intel.com
|
|
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
After we acquired all generic modeset locks in drm_modeset_lock_all, it's
unsafe acquire any other so just mark acquisition as done.
Atomic drivers shouldn't use drm_modeset_lock_all.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221152331.9212-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Harry Wentland <harry.wentland@amd.com>
|
|
This patch fixes compatible for STM32F7 USB OTG HS and consistently rename
dw2_set_params function.
The v2 former patch [1] had been acked by Paul Young, but v1 was merged.
[1] https://patchwork.kernel.org/patch/9925573/
Fixes: d8fae8b93682 ("usb: dwc2: add support for STM32F7xx USB OTG HS")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When I debug a kernel crash issue in funcitonfs, found ffs_data.ref
overflowed, While functionfs is unmounting, ffs_data is put twice.
Commit 43938613c6fd ("drivers, usb: convert ffs_data.ref from atomic_t to
refcount_t") can avoid refcount overflow, but that is risk some situations.
So no need put ffs data in ffs_fs_kill_sb, already put in ffs_data_closed.
The issue can be reproduced in Mediatek mt6763 SoC, ffs for ADB device.
KASAN enabled configuration reports use-after-free errro.
BUG: KASAN: use-after-free in refcount_dec_and_test+0x14/0xe0 at addr ffffffc0579386a0
Read of size 4 by task umount/4650
====================================================
BUG kmalloc-512 (Tainted: P W O ): kasan: bad access detected
-----------------------------------------------------------------------------
INFO: Allocated in ffs_fs_mount+0x194/0x844 age=22856 cpu=2 pid=566
alloc_debug_processing+0x1ac/0x1e8
___slab_alloc.constprop.63+0x640/0x648
__slab_alloc.isra.57.constprop.62+0x24/0x34
kmem_cache_alloc_trace+0x1a8/0x2bc
ffs_fs_mount+0x194/0x844
mount_fs+0x6c/0x1d0
vfs_kern_mount+0x50/0x1b4
do_mount+0x258/0x1034
INFO: Freed in ffs_data_put+0x25c/0x320 age=0 cpu=3 pid=4650
free_debug_processing+0x22c/0x434
__slab_free+0x2d8/0x3a0
kfree+0x254/0x264
ffs_data_put+0x25c/0x320
ffs_data_closed+0x124/0x15c
ffs_fs_kill_sb+0xb8/0x110
deactivate_locked_super+0x6c/0x98
deactivate_super+0xb0/0xbc
INFO: Object 0xffffffc057938600 @offset=1536 fp=0x (null)
......
Call trace:
[<ffffff900808cf5c>] dump_backtrace+0x0/0x250
[<ffffff900808d3a0>] show_stack+0x14/0x1c
[<ffffff90084a8c04>] dump_stack+0xa0/0xc8
[<ffffff900826c2b4>] print_trailer+0x158/0x260
[<ffffff900826d9d8>] object_err+0x3c/0x40
[<ffffff90082745f0>] kasan_report_error+0x2a8/0x754
[<ffffff9008274f84>] kasan_report+0x5c/0x60
[<ffffff9008273208>] __asan_load4+0x70/0x88
[<ffffff90084cd81c>] refcount_dec_and_test+0x14/0xe0
[<ffffff9008d98f9c>] ffs_data_put+0x80/0x320
[<ffffff9008d9d904>] ffs_fs_kill_sb+0xc8/0x110
[<ffffff90082852a0>] deactivate_locked_super+0x6c/0x98
[<ffffff900828537c>] deactivate_super+0xb0/0xbc
[<ffffff90082af0c0>] cleanup_mnt+0x64/0xec
[<ffffff90082af1b0>] __cleanup_mnt+0x10/0x18
[<ffffff90080d9e68>] task_work_run+0xcc/0x124
[<ffffff900808c8c0>] do_notify_resume+0x60/0x70
[<ffffff90080866e4>] work_pending+0x10/0x14
Cc: stable@vger.kernel.org
Signed-off-by: Xinyong <xinyong.fang@linux.alibaba.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The commit 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation")
and commit 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation")
made changes, which cause multiply overflow for 32-bit systems. The broken
timeout calculations leads to unexpected ETIMEDOUT errors and causes
stacktrace splat (such as below) during normal data exchange with SD-card.
| Running : 4M-check-reassembly-tcp-cmykw2-rotatew2.out -v0 -w1
| - Info: Finished target initialization.
| mmcblk0: error -110 transferring data, sector 320544, nr 2048, cmd
| response 0x900, card status 0x0
DIV_ROUND_UP_ULL helps to escape usage of __udivdi3() from libgcc and so
code gets compiled on all 32-bit platforms as opposed to usage of
DIV_ROUND_UP when we may only compile stuff on a very few arches.
Lets cast this multiply to u64 type to prevent the overflow.
Fixes: 9d9491a7da2a ("mmc: dw_mmc: Fix the DTO timeout calculation")
Fixes: 4c2357f57dd5 ("mmc: dw_mmc: Fix the CTO timeout calculation")
Tested-by: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Reported-by: Vineet Gupta <Vineet.Gupta1@synopsys.com> # ARC STAR 9001306872 HSDK, sdio: board crashes when copying big files
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: <stable@vger.kernel.org> # 4.14
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since commit ab82fa7da4dce5c7 ("gpio: rcar: Prevent module clock disable
when wake-up is enabled"), when a GPIO is used for wakeup, the GPIO
block's module clock (if exists) is manually kept running during system
suspend, to make sure the device stays active.
However, this explicit clock handling is merely a workaround for a
failure to properly communicate wakeup information to the device core.
Instead, set the device's power.wakeup_path field, to indicate this
device is part of the wakeup path. Depending on the PM Domain's
active_wakeup configuration, the genpd core code will keep the device
enabled (and the clock running) during system suspend when needed.
This allows for the removal of all explicit clock handling code from the
driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VF is used for accelerated networking it will likely have
more queues (and different policy) than the synthetic NIC.
This patch defers the queue policy to the VF so that all the
queues can be used. This impacts workloads like local generate UDP.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a race between napi_reschedule and re-enabling interrupts
which could lead to missed host interrrupts. This occurs when
interrupts are re-enabled (hv_end_read) and vmbus irq callback
(netvsc_channel_cb) has already scheduled NAPI.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Block setup of multiple channels earlier in the teardown
process. This avoids possible races between halt and subchannel
initialization.
Suggested-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to delete NAPI association if vmbus_open fails.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't wake transmit queues if link is not up yet.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the initialization order so that the device is ready to transmit
(ie connect vsp is completed) before setting the internal reference
to the device with RCU.
This avoids any races on initialization and prevents retry issues
on shutdown.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XDP_REDIRECT support for mergeable buffer was removed since commit
7324f5399b06 ("virtio_net: disable XDP_REDIRECT in receive_mergeable()
case"). This is because we don't reserve enough tailroom for struct
skb_shared_info which breaks XDP assumption. So this patch fixes this
by reserving enough tailroom and using fixed size of rx buffer.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPP units don't hold any reference on the channels connected to it.
It is the channel's responsibility to ensure that it disconnects from
its unit before being destroyed.
In practice, this is ensured by ppp_unregister_channel() disconnecting
the channel from the unit before dropping a reference on the channel.
However, it is possible for an unregistered channel to connect to a PPP
unit: register a channel with ppp_register_net_channel(), attach a
/dev/ppp file to it with ioctl(PPPIOCATTCHAN), unregister the channel
with ppp_unregister_channel() and finally connect the /dev/ppp file to
a PPP unit with ioctl(PPPIOCCONNECT).
Once in this situation, the channel is only held by the /dev/ppp file,
which can be released at anytime and free the channel without letting
the parent PPP unit know. Then the ppp structure ends up with dangling
pointers in its ->channels list.
Prevent this scenario by forbidding unregistered channels from
connecting to PPP units. This maintains the code logic by keeping
ppp_unregister_channel() responsible from disconnecting the channel if
necessary and avoids modification on the reference counting mechanism.
This issue seems to predate git history (successfully reproduced on
Linux 2.6.26 and earlier PPP commits are unrelated).
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we assumed that in case of error when adding FDB entries, the
write operation will fail, but this is not the case. Instead, we need to
check that the number of entries reported in the response is equal to
the number of entries specified in the request.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Highpoint RocketRAID 644L uses a Marvel 88SE9235 controller, as with
other Marvel controllers this needs a function 1 DMA alias quirk.
Note the RocketRAID 642L uses the same Marvel 88SE9235 controller and
already is listed with a function 1 DMA alias quirk.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Like the Highpoint Rocketraid 642L and cards using a Marvel 88SE9235
controller in general, this RAID card also supports AHCI mode and short
of a custom driver, this is the only way to make it work under Linux.
Note that even though the card is called to 644L, it has a product-id
of 0x0645.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1534106
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes from the timer departement:
- Add a missing timer wheel clock forward when migrating timers off a
unplugged CPU to prevent operating on a stale clock base and
missing timer deadlines.
- Use the proper shift count to extract data from a register value to
prevent evaluating unrelated bits
- Make the error return check in the FSL timer driver work correctly.
Checking an unsigned variable for less than zero does not really
work well.
- Clarify the confusing comments in the ARC timer code"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Forward timer base before migrating timers
clocksource/drivers/arc_timer: Update some comments
clocksource/drivers/mips-gic-timer: Use correct shift count to extract data
clocksource/drivers/fsl_ftm_timer: Fix error return checking
|
|
Errors while developing the patch to create of_overlay_fdt_apply()
exposed inadequate error messages to debug problems when overlay
devicetree fragment nodes contain an invalid target path. Improve
the messages in find_target_node() to remedy this.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
|
|
The unittest-data overlays have been pulled into proper overlay
devicetree source files without changing their format. The
next step is to convert them to use sugar syntax instead of
hand coding overlay fragments structure.
A few of the overlays can not be converted because they test
absolute target paths in the overlay fragment. dtc does not
generate this type of target:
overlay_0.dts
overlay_1.dts
overlay_12.dts
overlay_13.dts
Two pre-existing unittest overlay devicetree source files are
also converted:
overlay_bad_phandle.dts
overlay_bad_symbol.dts
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
|
|
Move duplicating and unflattening of an overlay flattened devicetree
(FDT) into the overlay application code. To accomplish this,
of_overlay_apply() is replaced by of_overlay_fdt_apply().
The copy of the FDT (aka "duplicate FDT") now belongs to devicetree
code, which is thus responsible for freeing the duplicate FDT. The
caller of of_overlay_fdt_apply() remains responsible for freeing the
original FDT.
The unflattened devicetree now belongs to devicetree code, which is
thus responsible for freeing the unflattened devicetree.
These ownership changes prevent early freeing of the duplicated FDT
or the unflattened devicetree, which could result in use after free
errors.
of_overlay_fdt_apply() is a private function for the anticipated
overlay loader.
Update unittest.c to use of_overlay_fdt_apply() instead of
of_overlay_apply().
Move overlay fragments from artificial locations in
drivers/of/unittest-data/tests-overlay.dtsi into one devicetree
source file per overlay. This led to changes in
drivers/of/unitest-data/Makefile and drivers/of/unitest.c.
- Add overlay directives to the overlay devicetree source files so
that dtc will compile them as true overlays into one FDT data
chunk per overlay.
- Set CFLAGS for drivers/of/unittest-data/testcases.dts so that
symbols will be generated for overlay resolution of overlays
that are no longer artificially contained in testcases.dts
- Unflatten and apply each unittest overlay FDT using
of_overlay_fdt_apply().
- Enable the of_resolve_phandles() check for whether the unflattened
overlay is detached. This check was previously disabled because the
overlays from tests-overlay.dtsi were not unflattened into detached
trees.
- Other changes to unittest.c infrastructure to manage multiple test
FDTs built into the kernel image (access by name instead of
arbitrary number).
- of_unittest_overlay_high_level(): previously unused code to add
properties from the overlay_base devicetree to the live tree
was triggered by the restructuring of tests-overlay.dtsi and thus
testcases.dts. This exposed two bugs: (1) the need to dup a
property before adding it, and (2) property 'name' is
auto-generated in the unflatten code and thus will be a duplicate
in the __symbols__ node - do not treat this duplicate as an error.
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A driver fix and a documentation fix (which makes dependency handling
for the next cycle easier)"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: octeon: Prevent error message on bus error
dt-bindings: at24: sort manufacturers alphabetically
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A 4.16 regression fix, three fixes for -stable, and a cleanup fix:
- During the merge window support for the new ACPI NVDIMM Platform
Capabilities structure disabled support for "deep flush", a
force-unit- access like mechanism for persistent memory. Restore
that mechanism.
- VFIO like RDMA is yet one more memory registration / pinning
interface that is incompatible with Filesystem-DAX. Disable long
term pins of Filesystem-DAX mappings via VFIO.
- The Filesystem-DAX detection to prevent long terms pins mistakenly
also disabled Device-DAX pins which are not subject to the same
block- map collision concerns.
- Similar to the setup path, softlockup warnings can trigger in the
shutdown path for large persistent memory namespaces. Teach
for_each_device_pfn() to perform cond_resched() in all cases.
- Boaz noticed that the might_sleep() in dax_direct_access() is stale
as of the v4.15 kernel.
These have received a build success notification from the 0day robot,
and the longterm pin fixes have appeared in -next. However, I recently
rebased the tree to remove some other fixes that need to be reworked
after review feedback.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
vfio: disable filesystem-dax page pinning
dax: fix vma_is_fsdax() helper
dax: ->direct_access does not sleep anymore
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- some build fixes with randconfigs
- an m88ds3103 fix to prevent an OOPS if the chip doesn't provide the
right version during probe (with can happen if the hardware hangs)
- a potential out of array bounds reference in tvp5150
- some fixes and improvements in the DVB memory mapped API (added for
kernel 4.16)
* tag 'media/v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vb2: Makefile: place vb2-trace together with vb2-core
media: Don't let tvp5150_get_vbi() go out of vbi_ram_default array
media: dvb: update buffer mmaped flags and frame counter
media: dvb: add continuity error indicators for memory mapped buffers
media: dmxdev: Fix the logic that enables DMA mmap support
media: dmxdev: fix error code for invalid ioctls
media: m88ds3103: don't call a non-initalized function
media: au0828: add VIDEO_V4L2 dependency
media: dvb: fix DVB_MMAP dependency
media: dvb: fix DVB_MMAP symbol name
media: videobuf2: fix build issues with vb2-trace
media: videobuf2: Add VIDEOBUF2_V4L2 Kconfig option for VB2 V4L2 part
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- rave-sp: add NVMEM dependency
- build fixes for i6300esb_wdt, xen_wdt and sp5100_tco
* tag 'linux-watchdog-4.16-fixes-1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco.c: fix potential build failure
watchdog: xen_wdt: fix potential build failure
watchdog: i6300esb: fix build failure
watchdog: rave-sp: add NVMEM dependency
|
|
Gen8 and prior Proliant systems supported the "CRU" interface
to firmware. This interfaces allows linux to "call back" into firmware
to source the cause of an NMI. This feature isn't fully utilized
as the actual source of the NMI isn't printed, the driver only
indicates that the source couldn't be determined when the call
fails.
With the advent of Gen9, iCRU replaces the CRU. The call back
feature is no longer available in firmware. To be compatible and
not attempt to call back into firmware on system not supporting CRU,
the SMBIOS table is consulted to determine if it is safe to
make the call back or not.
This results in about half of the driver code being devoted
to either making CRU calls or determing if it is safe to make
CRU calls. As noted, the driver isn't really using the results of
the CRU calls.
Furthermore, as a consequence of the Spectre security issue, the
BIOS/EFI calls are being wrapped into Spectre-disabling section.
Removing the call back in hpwdt_pretimeout assists in this effort.
As the CRU sourcing of the NMI isn't required for handling the
NMI and there are security concerns with making the call back, remove
the legacy (pre Gen9) NMI sourcing and the DMI code to determine if
the system had the CRU interface.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
According to SBSA spec v3.1 section 5.3:
All registers are 32 bits in size and should be accessed using
32-bit reads and writes. If an access size other than 32 bits
is used then the results are IMPLEMENTATION DEFINED.
[...]
The Generic Watchdog is little-endian
The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.
Fix this by using lo_hi_readq() that does two 32-bit reads.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.
$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!
Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Re-enable deep flush so that users always have a way to be sure that a
write makes it all the way out to media. Writes from the PMEM driver
always arrive at the NVDIMM since movnt is used to bypass the cache, and
the driver relies on the ADR (Asynchronous DRAM Refresh) mechanism to
flush write buffers on power failure. The Deep Flush mechanism is there
to explicitly write buffers to protect against (rare) ADR failure. This
change prevents a regression in deep flush behavior so that applications
can continue to depend on fsync() as a mechanism to trigger deep flush
in the filesystem-DAX case.
Fixes: 06e8ccdab15f4 ("acpi: nfit: Add support for detect platform CPU cache...")
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Filesystem-DAX is incompatible with 'longterm' page pinning. Without
page cache indirection a DAX mapping maps filesystem blocks directly.
This means that the filesystem must not modify a file's block map while
any page in a mapping is pinned. In order to prevent the situation of
userspace holding of filesystem operations indefinitely, disallow
'longterm' Filesystem-DAX mappings.
RDMA has the same conflict and the plan there is to add a 'with lease'
mechanism to allow the kernel to notify userspace that the mapping is
being torn down for block-map maintenance. Perhaps something similar can
be put in place for vfio.
Note that xfs and ext4 still report:
"DAX enabled. Warning: EXPERIMENTAL, use at your own risk"
...at mount time, and resolving the dax-dma-vs-truncate problem is one
of the last hurdles to remove that designation.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org>
Reported-by: Haozhong Zhang <haozhong.zhang@intel.com>
Tested-by: Haozhong Zhang <haozhong.zhang@intel.com>
Fixes: d475c6346a38 ("dax,ext2: replace XIP read and write with DAX I/O")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Update pci.ids location (documentation only) (Randy Dunlap)
- Fix a crash when BIOS didn't assign a BAR and we try to enlarge it
(Christian König)
* tag 'pci-v4.16-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Allow release of resources that were never assigned
PCI: Update location of pci.ids file
|
|
If we fail to authenticate HuC firmware, we should change
its load status to FAIL. While around, print HUC_STATUS
on firmware verification failure.
v2: keep the variables sorted by length (Chris)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302133718.1260-1-michal.wajdeczko@intel.com
|
|
We want to use higher level 'uc' functions as the main entry points to
the GuC/HuC code to hide some details and keep code layered.
While here, move call to disable_guc_interrupts after sending suspend
action to the GuC to allow it work also with CTB as comm mechanism.
v2: update commit msg (Sagar)
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302111550.21328-1-michal.wajdeczko@intel.com
|
|
During reset/wedging, we have to clean up the requests on the timeline
and flush the pending interrupt state. Currently, we are abusing the irq
disabling of the timeline spinlock to protect the irq state in
conjunction to the engine's timeline requests, but this is accidental
and conflates the spinlock with the irq state. A baffling state of
affairs for the reader.
Instead, explicitly disable irqs over the critical section, and separate
modifying the irq state from the timeline's requests.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302143246.2579-4-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
|
|
Although this state (execlists->active and engine->irq_posted) itself is
not protected by the engine->timeline spinlock, it does conveniently
ensure that irqs are disabled. We can use this to protect our
manipulation of the state and so ensure that the next IRQ to arrive sees
consistent state and (hopefully) ignores the reset engine.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302131246.22036-1-chris@chris-wilson.co.uk
|
|
After staring hard at sequences like
[ 28.199013] systemd-1 2..s. 26062228us : execlists_submission_tasklet: rcs0 cs-irq head=0 [0?], tail=1 [1?]
[ 28.199095] systemd-1 2..s. 26062229us : execlists_submission_tasklet: rcs0 csb[1]: status=0x00000018:0x00000000, active=0x1
[ 28.199177] systemd-1 2..s. 26062230us : execlists_submission_tasklet: rcs0 out[0]: ctx=0.1, seqno=3, prio=-1024
[ 28.199258] systemd-1 2..s. 26062231us : execlists_submission_tasklet: rcs0 completed ctx=0
[ 28.199340] gem_eio-829 1..s1 26066853us : execlists_submission_tasklet: rcs0 in[0]: ctx=1.1, seqno=1, prio=0
[ 28.199421] <idle>-0 2..s. 26066863us : execlists_submission_tasklet: rcs0 cs-irq head=1 [1?], tail=2 [2?]
[ 28.199503] <idle>-0 2..s. 26066865us : execlists_submission_tasklet: rcs0 csb[2]: status=0x00000001:0x00000000, active=0x1
[ 28.199585] gem_eio-829 1..s1 26067077us : execlists_submission_tasklet: rcs0 in[1]: ctx=3.1, seqno=2, prio=0
[ 28.199667] gem_eio-829 1..s1 26067078us : execlists_submission_tasklet: rcs0 in[0]: ctx=1.2, seqno=1, prio=0
[ 28.199749] <idle>-0 2..s. 26067084us : execlists_submission_tasklet: rcs0 cs-irq head=2 [2?], tail=3 [3?]
[ 28.199830] <idle>-0 2..s. 26067085us : execlists_submission_tasklet: rcs0 csb[3]: status=0x00008002:0x00000001, active=0x1
[ 28.199912] <idle>-0 2..s. 26067086us : execlists_submission_tasklet: rcs0 out[0]: ctx=1.2, seqno=1, prio=0
[ 28.199994] gem_eio-829 2..s. 28246084us : execlists_submission_tasklet: rcs0 cs-irq head=3 [3?], tail=4 [4?]
[ 28.200096] gem_eio-829 2..s. 28246088us : execlists_submission_tasklet: rcs0 csb[4]: status=0x00000014:0x00000001, active=0x5
[ 28.200178] gem_eio-829 2..s. 28246089us : execlists_submission_tasklet: rcs0 out[0]: ctx=0.0, seqno=0, prio=0
[ 28.200260] gem_eio-829 2..s. 28246127us : execlists_submission_tasklet: execlists_submission_tasklet:886 GEM_BUG_ON(buf[2 * head + 1] != port->context_id)
the conclusion is that the only place where the ports are reset to zero,
is from engine->cancel_requests called during i915_gem_set_wedged().
The race is horrible as it results from calling set-wedged on active HW
(the GPU reset failed) and as such we need to be careful as the HW state
changes beneath us. Fortunately, it's the same scary conditions as
affect normal reset, so we can reuse the same machinery to disable state
tracking as we clobber it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104945
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Fixes: af7a8ffad9c5 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180302113324.23189-2-chris@chris-wilson.co.uk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Five minor fixes for Xen-specific drivers"
* tag 'for-linus-4.16a-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
pvcalls-front: 64-bit align flags
x86/xen: add tty0 and hvc0 as preferred consoles for dom0
xen-netfront: Fix hang on device removal
xen/pirq: fix error path cleanup when binding MSIs
xen/pvcalls: fix null pointer dereference on map->sock
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes for this series. This is a little larger than
usual at this time, but that's mainly because I was out on vacation
last week. Nothing in here is major in any way, it's just two weeks of
fixes. This contains:
- NVMe pull from Keith, with a set of fixes from the usual suspects.
- mq-deadline zone unlock fix from Damien, fixing an issue with the
SMR zone locking added for 4.16.
- two bcache fixes sent in by Michael, with changes from Coly and
Tang.
- comment typo fix from Eric for blktrace.
- return-value error handling fix for nbd, from Gustavo.
- fix a direct-io case where we don't defer to a completion handler,
making us sleep from IRQ device completion. From Jan.
- a small series from Jan fixing up holes around handling of bdev
references.
- small set of regression fixes from Jiufei, mostly fixing problems
around the gendisk pointer -> partition index change.
- regression fix from Ming, fixing a boundary issue with the discard
page cache invalidation.
- two-patch series from Ming, fixing both a core blk-mq-sched and
kyber issue around token freeing on a requeue condition"
* tag 'for-linus-20180302' of git://git.kernel.dk/linux-block: (24 commits)
block: fix a typo
block: display the correct diskname for bio
block: fix the count of PGPGOUT for WRITE_SAME
mq-deadline: Make sure to always unlock zones
nvmet: fix PSDT field check in command format
nvme-multipath: fix sysfs dangerously created links
nbd: fix return value in error handling path
bcache: fix kcrashes with fio in RAID5 backend dev
bcache: correct flash only vols (check all uuids)
blktrace_api.h: fix comment for struct blk_user_trace_setup
blockdev: Avoid two active bdev inodes for one device
genhd: Fix BUG in blkdev_open()
genhd: Fix use after free in __blkdev_get()
genhd: Add helper put_disk_and_module()
genhd: Rename get_disk() to get_disk_and_module()
genhd: Fix leaked module reference for NVME devices
direct-io: Fix sleep in atomic due to sync AIO
nvme-pci: Fix nvme queue cleanup if IRQ setup fails
block: kyber: fix domain token leak during requeue
blk-mq: don't call io sched's .requeue_request when requeueing rq to ->dispatch
...
|
