| Age | Commit message (Collapse) | Author |
|---|
|
Since scsi_device_quiesce() skips SCSI devices that have another state than
RUNNING, OFFLINE or TRANSPORT_OFFLINE, scsi_device_resume() should not
complain about SCSI devices that have been skipped. Hence this patch. This
patch avoids that the following warning appears during resume:
WARNING: CPU: 3 PID: 1039 at blk_clear_pm_only+0x2a/0x30
CPU: 3 PID: 1039 Comm: kworker/u8:49 Not tainted 5.0.0+ #1
Hardware name: LENOVO 4180F42/4180F42, BIOS 83ET75WW (1.45 ) 05/10/2013
Workqueue: events_unbound async_run_entry_fn
RIP: 0010:blk_clear_pm_only+0x2a/0x30
Call Trace:
? scsi_device_resume+0x28/0x50
? scsi_dev_type_resume+0x2b/0x80
? async_run_entry_fn+0x2c/0xd0
? process_one_work+0x1f0/0x3f0
? worker_thread+0x28/0x3c0
? process_one_work+0x3f0/0x3f0
? kthread+0x10c/0x130
? __kthread_create_on_node+0x150/0x150
? ret_from_fork+0x1f/0x30
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Oleksandr Natalenko <oleksandr@natalenko.name>
Cc: Martin Steigerwald <martin@lichtvoll.de>
Cc: <stable@vger.kernel.org>
Reported-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Tested-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fixes: 3a0a529971ec ("block, scsi: Make SCSI quiesce and resume work reliably") # v4.15
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
cmd->rcu is initialized by scsi_initialize_rq(). For passthrough
requests, blk_get_request() calls scsi_initialize_rq(). For filesystem
requests, scsi_init_command() calls scsi_initialize_rq(). Make sure
that destroy_rcu_head() is called for passthrough requests.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The following traceback was reported on ASUS C201, which does not support
console logging.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 361 at kernel/workqueue.c:3030 __flush_work+0x38/0x154
Modules linked in: snd_soc_hdmi_codec cros_ec_debugfs cros_ec_sysfs uvcvideo dw_hdmi_cec dw_hdmi_i2s_audio videobuf2_vmalloc cfg80211 gpio_charger rk_crypto rfkill videobuf2_memops videobuf2_v4l2 des_generic videobuf2_common ofpart m25p80 spi_nor tpm_i2c_infineon sbs_battery mtd tpm joydev cros_ec_dev coreboot_table evdev mousedev ip_tables x_tables [last unloaded: brcmutil]
CPU: 2 PID: 361 Comm: systemd-sleep Not tainted 5.1.0-rc1-1-ARCH+ #1
Hardware name: Rockchip (Device Tree)
[<c020e4b0>] (unwind_backtrace) from [<c020ac18>] (show_stack+0x10/0x14)
[<c020ac18>] (show_stack) from [<c07a3e04>] (dump_stack+0x7c/0x9c)
[<c07a3e04>] (dump_stack) from [<c0222748>] (__warn+0xd0/0xec)
[<c0222748>] (__warn) from [<c022279c>] (warn_slowpath_null+0x38/0x44)
[<c022279c>] (warn_slowpath_null) from [<c02365d0>] (__flush_work+0x38/0x154)
[<c02365d0>] (__flush_work) from [<c023786c>] (__cancel_work_timer+0x114/0x1a4)
[<c023786c>] (__cancel_work_timer) from [<bf33233c>] (cros_ec_debugfs_suspend+0x14/0x1c [cros_ec_debugfs])
[<bf33233c>] (cros_ec_debugfs_suspend [cros_ec_debugfs]) from [<c056a888>] (dpm_run_callback+0x64/0xcc)
[<c056a888>] (dpm_run_callback) from [<c056ad2c>] (__device_suspend+0x174/0x3a8)
[<c056ad2c>] (__device_suspend) from [<c056b9e0>] (dpm_suspend+0x174/0x1e0)
[<c056b9e0>] (dpm_suspend) from [<c026b3e0>] (suspend_devices_and_enter+0x6c/0x50c)
[<c026b3e0>] (suspend_devices_and_enter) from [<c026ba8c>] (pm_suspend+0x20c/0x274)
[<c026ba8c>] (pm_suspend) from [<c026a628>] (state_store+0x54/0x88)
[<c026a628>] (state_store) from [<c03cd2d0>] (kernfs_fop_write+0x114/0x180)
[<c03cd2d0>] (kernfs_fop_write) from [<c035d48c>] (__vfs_write+0x1c/0x154)
[<c035d48c>] (__vfs_write) from [<c035f9e8>] (vfs_write+0xb8/0x198)
[<c035f9e8>] (vfs_write) from [<c035fbc0>] (ksys_write+0x3c/0x74)
[<c035fbc0>] (ksys_write) from [<c0201000>] (ret_fast_syscall+0x0/0x4c)
Exception stack(0xe9365fa8 to 0xe9365ff0)
5fa0: 00000004 beef8b28 00000004 beef8b28 00000004 00000000
5fc0: 00000004 beef8b28 02319170 00000004 beef8b28 00000004 b6f3d900 beef8b74
5fe0: 0000006c beef8a98 b6c0adac b6c66534
---[ end trace f4ee5df14e8ea0ec ]---
If console logging is not supported, the work structure is never
initialized, resulting in the traceback. Calling cancel/schedule functions
conditionally fixes the problem.
While at it, also fix error handling in the probe function.
Reported-by: Urja Rannikko <urjaman@gmail.com>
Cc: Urja Rannikko <urjaman@gmail.com>
Fixes: 6fce0a2cf5a05 ("mfd / platform: cros_ec: Move debugfs attributes to its own driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
Fix sparse warning:
drivers/base/swnode.c:475:22: warning: symbol 'software_node_get_parent' was not declared. Should it be static?
drivers/base/swnode.c:484:22: warning: symbol 'software_node_get_next_child' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
My commit 26a7b5473191 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b5473191 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix following schedule while atomic in mt76x02_reset_state
since synchronize_rcu is run inside a RCU section
[44036.944222] mt76x2e 0000:06:00.0: MCU message 31 (seq 3) timed out
[44036.944281] BUG: sleeping function called from invalid context at kernel/rcu/tree_exp.h:818
[44036.944284] in_atomic(): 1, irqs_disabled(): 0, pid: 28066, name: kworker/u4:1
[44036.944287] INFO: lockdep is turned off.
[44036.944292] CPU: 1 PID: 28066 Comm: kworker/u4:1 Tainted: G W 5.0.0-rc7-wdn-t1+ #7
[44036.944294] Hardware name: Dell Inc. Studio XPS 1340/0K183D, BIOS A11 09/08/2009
[44036.944305] Workqueue: phy1 mt76x02_wdt_work [mt76x02_lib]
[44036.944308] Call Trace:
[44036.944317] dump_stack+0x67/0x90
[44036.944322] ___might_sleep.cold.88+0x9f/0xaf
[44036.944327] rcu_blocking_is_gp+0x13/0x50
[44036.944330] synchronize_rcu+0x17/0x80
[44036.944337] mt76_sta_state+0x138/0x1d0 [mt76]
[44036.944349] mt76x02_wdt_work+0x1c9/0x610 [mt76x02_lib]
[44036.944355] process_one_work+0x2a5/0x620
[44036.944361] worker_thread+0x35/0x3e0
[44036.944368] kthread+0x11c/0x140
[44036.944376] ret_from_fork+0x3a/0x50
[44036.944384] BUG: scheduling while atomic: kworker/u4:1/28066/0x00000002
[44036.944387] INFO: lockdep is turned off.
[44036.944389] Modules linked in: cmac ctr ccm af_packet snd_hda_codec_hdmi
Introduce __mt76_sta_remove in order to run sta_remove without holding dev->mutex.
Move __mt76_sta_remove outside of RCU section in mt76x02_reset_state
Fixes: e4ebb8b403d1 ("mt76: mt76x2: implement full device restart on watchdog reset")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
|
|
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Andrey has reported on OpenWrt's bug tracking system[1], that he
currently can't use ar93xx_uart as pure serial UART without console
(CONFIG_SERIAL_8250_CONSOLE and CONFIG_SERIAL_AR933X_CONSOLE undefined),
because compilation ends with following error:
ar933x_uart.c: In function 'ar933x_uart_console_write':
ar933x_uart.c:550:14: error: 'struct uart_port' has no
member named 'sysrq'
So this patch moves all the code related to console handling behind
series of CONFIG_SERIAL_AR933X_CONSOLE ifdefs.
1. https://bugs.openwrt.org/index.php?do=details&task_id=2152
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Andrey Batyiev <batyiev@gmail.com>
Reported-by: Andrey Batyiev <batyiev@gmail.com>
Tested-by: Andrey Batyiev <batyiev@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When building with -Wsometimes-uninitialized, Clang warns:
drivers/tty/serial/qcom_geni_serial.c:1079:6: warning: variable 'baud'
is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
It's not wrong; when options is NULL, baud has no default value. Use
9600 as that is a sane default.
Link: https://github.com/ClangBuiltLinux/linux/issues/395
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the missing uart_unregister_driver() and i2c_del_driver() before return
from sc16is7xx_init() in the error handling case.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case ioremap fails, the fix returns -ENOMEM to avoid NULL
pointer dereferences.
Multiple places use port.membase.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case dmaengine_prep_dma_cyclic fails, the fix returns a proper
error code to avoid NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Fixes: 34df42f59a60 ("serial: at91: add rx dma support")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_match_device can return a NULL pointer when matching device is not
found. This patch avoids a scenario causing NULL pointer derefernce.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
of_match_device on failure to find a matching device can return a NULL
pointer. The patch checks for such a scenrio and passes the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to compare *port* with >= 0 because such comparison
of an unsigned value is always true.
Fix this by removing such comparison.
Addresses-Coverity-ID: 1443949 ("Unsigned compared against 0")
Fixes: 02a50b875046 ("usb: usb251xb: add usb data lane port swap feature")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add __printf attribute to fusb302_log function, so that we get
compiler warnings when specifying wrong vararg parameters.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the code which avoids doing i2c-transfers while our parent
i2c-adapter may be suspended by busy-waiting for our resume handler
to be called.
Instead move the interrupt handling from a threaded interrupt handler
to a work-queue and install a non-threaded interrupt handler which
normally queues the new interrupt handling work directly.
When our suspend handler gets called we set a flag which makes the new
non-threaded interrupt handler skip queueing the work before our parent
i2c-adapter is ready, instead the new non-threaded handler will record an
interrupt has happened during suspend and then our resume handler will
queue the work (at which point our parent will be ready).
Note normally i2c drivers solve the problem of not being able to access
the i2c bus until the i2c-controller is resumed by simply disabling their
irq from the suspend handler and re-enabling it on resume.
That is not possible with the fusb302 since the irq is a wakeup source
(it must be a wakeup source so that we can do PD negotiation when a
charger gets plugged in while suspended).
Besides avoiding the ugly busy-wait, this also fixes the following errors
which were logged by the busy-wait code when woken from suspend by plugging
in a Type-C device:
fusb302: i2c: pm suspend, retry 1 / 10
fusb302: i2c: pm suspend, retry 2 / 10
etc.
This commit also changes the devm_request_irq to a regular request_irq
+ free_irq, so that the work can be properly stopped. While at it also
properly disable the wake setting on the irq and also properly stop the
delayed work for bcl handling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a copy and paste error in an error message and a spelling error
in a comment.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The FUSB302 will stop toggling with a FUSB_REG_STATUS1A_TOGSS_SRC? status,
as soon as it sees either Ra or Rd on a CC pin.
Before this commit fusb302_handle_togdone_src would assume that the toggle-
engine always stopped at the CC pin indicating the polarity, IOW it assumed
that it stopped at the pin connected to Rd. It did check the CC-status of
that pin, but it did not expect to get a CC-status of Ra and therefore
treated this as CC-open. This lead to the following 2 problems:
1) If a powered cable/adapter gets plugged in with Ra on CC1 and Rd on CC2
then 4 of 5 times when plugged in toggling will stop with a togdone_result
of FUSB_REG_STATUS1A_TOGSS_SRC1. 3/5th of the time the toggle-engine is
testing for being connected as a sink and after that it tests 1/5th of the
time for connected as a src through CC1 before finally testing the last
1/5th of the time for being a src connected through CC2.
This was a problem because we would only check the CC pin status for the
pin on which the toggling stopped which in this polarity 4 out of 5
times would be the Ra pin. The code before this commit would treat Ra as
CC-open and then restart toggling. Once toggling is restarted we are
guaranteed to end with FUSB_REG_STATUS1A_TOGSS_SRC1 as CC1 is tested first,
leading to a CC-status of Ra again and an infinite restart toggling loop.
So 4 out of 5 times when plugged in in this polarity a powered adapter
will not work.
2) Even if we happen to have the right polarity or 1/5th of the time in
the polarity with problem 1), we would report the non Rd pin as CC-open
rather then as Ra, resulting in the tcpm.c code not enabling Vconn which
is a problem for some adapters.
This commit fixes this by getting the CC-status of *both* pins and then
determining the polarity based on that, rather then on where the toggling
stopped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The datasheet says the vconn MUST be off when we start toggling. The
tcpm.c state-machine is responsible to make sure vconn is off, but lets
add a WARN to catch any cases where vconn is not off for some reason.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After the recent cleanups, tcpm_set_cc is the only caller of
fusb302_set_cc_pull, fold fusb302_set_cc_pull directly into
tcpm_set_cc for a nice cleanup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit ea3b4d5523bc ("usb: typec: fusb302: Resolve fixed power role
contract setup"), tcpm_set_cc always calls fusb302_set_toggling.
Before this refactor tcpm_set_cc does the following:
1) fusb302_set_toggling(TOGGLING_MODE_OFF),
this sets both FUSB_REG_MASK_BC_LVL and FUSB_REG_MASK_COMP_CHNG.
2) fusb302_set_cc_pull(...).
3) "reset cc status".
4) if pull-up fusb302_set_src_current(...).
5) if pull-up or pull-down enable bc-lvl resp comp-chng irq.
6) fusb302_set_toggling(new-toggling-mode), which again
sets both FUSB_REG_MASK_BC_LVL and FUSB_REG_MASK_COMP_CHNG disabling
the just enabled irq. fusb302_set_toggling is skipped when the new
toggling mode is TOGGLING_MODE_OFF because this is already done in 1,
note in this case 5) is a no-op.
When we are toggling the bits set by fusb302_set_cc_pull will be ignored
until we turn toggling off, so we can safely move the fusb302_set_cc_pull
call to before setting TOGGLING_MODE_OFF.
Either we are not toggling yet, or the src-current has already been set,
so we can also safely set the src-current earlier, allowing us to do the
fusb302_set_toggling(TOGGLING_MODE_OFF) call at the same time as we
set the other toggling modes. Also setting the src-current is a no-op
when not enabling pull-ups, so we can drop the if.
And since the second fusb302_set_toggling undoes the effects of step 5,
we can skip step 5, the bc-lvl resp comp-chng irq wil be enabled by
fusb302_handle_togdone_snk resp. fusb302_handle_togdone_src when toggling
is done.
Together this allows us to simplify things to:
1) fusb302_set_cc_pull(...)
2) "reset cc status"
3) fusb302_set_src_current(...)
4) fusb302_set_toggling(new-toggling-mode)
This commit does this, leading to a nice cleanup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 2 callers of fusb302_set_cc_polarity both call fusb302_set_cc_pull
directly before calling fusb302_set_cc_polarity, this is not ideal for
2 reasons:
1) fusb302_set_cc_pull uses the cached polarity when applying the pull-ups,
which maybe changed immediately afterwards, to fix this set_cc_polarity
already does the pull-up setting.
2) Both touch the SWITCHES0 register in a r-w-modify cycle, this leads to
read reg, write reg, read reg, write reg. If we fold the setting of
the pull-downs into fusb302_set_cc_polarity then not only can we avoid
doing the reads / writes twice, at this point we set all bits, so we
can skip the read, turning 4 (slowish) i2c-transfers into 1.
Doing this also avoids the need to cache the pull_up state in
struct fusb302_chip.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Keep the orientation value when setting the mux to safe mode, this
fixes the orientation getting reset when switching alt-modes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If our port-partner supports both DP-only operation (pin-assignment C)
and multi-func operation (pin-assignment D) and we only support
pin-assignment D and the port-partner prefers DP-only mode, then
before this commit we would and up masking out pin-assignment D from
the available pin-assignments and fail to pick a pin-assignment.
Instead only mask out the multi-func pin-assignments if we support
dp-only pin-assignments, so that we correctly fall-back to a multi-func
pin-assignment in this case (by picking pin-assignment D).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"vdev" points to vhci_hcd->vdev[] array and vhci_hcd->vdev[] array
is not a pointer array but a structure array and it is already used
in vhci_urb_enqueue() and then passed to vhci_tx_urb() as an argument.
vhci_tx_urb() is not called except vhci_urb_enqueue(). So, "vdev"
can not be null pointer. This null check statement is meaningless.
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.
Fixes: 98bfb3946695 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
PD 2.0 sinks are supposed to accept src-capabilities with a 3.0 header and
simply ignore any src PDOs which the sink does not understand such as PPS
but some 2.0 sinks instead ignore the entire PD_DATA_SOURCE_CAP message,
causing contract negotiation to fail.
This commit fixes such sinks not working by re-trying the contract
negotiation with PD-2.0 source-caps messages if we don't have a contract
after PD_N_HARD_RESET_COUNT hard-reset attempts.
The problem fixed by this commit was noticed with a Type-C to VGA dongle.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.
[ 101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[ 101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
Signed-off-by: Yasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: Spyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message error and return
*irq* in case platform_get_irq() fails.
Addresses-Coverity-ID: 1443899 ("Improper use of negative value")
Fixes: d2061f9cc32d ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports. The fifth is a network interface supported
by the qmi-wwan driver. Furthermore, the serial ports do not support
modem control signals. Add driver_info flags to reflect this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Fixes: ec0cd94d881c ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org> # 3.2
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
As part of the TX completion path, qeth_release_skbs() frees the completed
skbs with __skb_queue_purge(). This ends in kfree_skb(), reporting every
completed skb as dropped.
On the other hand when dropping an skb in .ndo_start_xmit, we end up
calling consume_skb()... where we should be using kfree_skb() so that
drop monitors get notified.
Switch the drop/consume logic around, and also don't accumulate dropped
packets in the tx_errors statistics.
Fixes: dc149e3764d8 ("s390/qeth: replace open-coded skb_queue_walk()")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ucast IP table is utilized by some of the L3-specific sysfs attributes
that qeth_l3_create_device_attributes() provides. So initialize the table
_before_ registering the attributes.
Fixes: ebccc7397e4a ("s390/qeth: add missing hash table initializations")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HW trap and VNICC configuration is exposed via sysfs, and may have
already been modified when qeth_l?_probe_device() attempts to initialize
them. So (1) initialize the VNICC values a little earlier, and (2) don't
bother about the HW trap mode, it was already initialized before.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device ID alone does not uniquely identify a device. Test both the
vendor and device ID to make sure we don't mistakenly think some other
vendor's 0xB410 device is a Digium HFC4S. Also, instead of the bare hex
ID, use the same constant (PCI_DEVICE_ID_DIGIUM_HFC4S) used in the device
ID table.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ad6c9986bcb62 ("vxlan: Fix GRO cells race condition between
receive and link delete") fixed a race condition for the typical case a vxlan
device is dismantled from the current netns. But if a netns is dismantled,
vxlan_destroy_tunnels() is called to schedule a unregister_netdevice_queue()
of all the vxlan tunnels that are related to this netns.
In vxlan_destroy_tunnels(), gro_cells_destroy() is called and finished before
unregister_netdevice_queue(). This means that the gro_cells_destroy() call is
done too soon, for the same reasons explained in above commit.
So we need to fully respect the RCU rules, and thus must remove the
gro_cells_destroy() call or risk use after-free.
Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer")
Signed-off-by: Suanming.Mou <mousuanming@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP/UDP checksum validity was propagated to skb
only if IP checksum is valid.
But for IPv6 there is no validity as there is no checksum in IPv6.
This patch propagates TCP/UDP checksum validity regardless of IP checksum.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bug that Stan reported is as follows. After a restart, a 16-bit NIC
may be incorrectly identified as a 32-bit NIC and stop working.
mac8390 slot.E: Memory length resource not found, probing
mac8390 slot.E: Farallon EtherMac II-C (type farallon)
mac8390 slot.E: MAC 00:00:c5:30:c2:99, IRQ 61, 32 KB shared memory at 0xfeed0000, 32-bit access.
The bug never arises after a cold start and only intermittently after a
warm start. (I didn't investigate why the bug is intermittent.)
It turns out that memcpy_toio() is deprecated and memcmp_withio() also
has issues. Replacing these calls with mmio accessors fixes the problem.
Reported-and-tested-by: Stan Johnson <userm57@yahoo.com>
Fixes: 2964db0f5904 ("m68k: Mac DP8390 update")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly to commit a7603ac1fc8c ("geneve: change NET_UDP_TUNNEL
dependency to select"), GTP has a dependency on NET_UDP_TUNNEL which
makes impossible to compile it if no other protocol depending on
NET_UDP_TUNNEL is selected.
Fix this by changing the depends to a select, and drop NET_IP_TUNNEL from
the select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We assumed that vm_mmap() would reject an attempt to mmap past the end of
the filp (our object), but we were wrong.
Applications that tried to use the mmap beyond the end of the object
would be greeted by a SIGBUS. After this patch, those applications will
be told about the error on creating the mmap, rather than at a random
moment on later access.
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Testcase: igt/gem_mmap/bad-size
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190314075829.16838-1-chris@chris-wilson.co.uk
(cherry picked from commit 794a11cb67201ad1bb61af510bb8460280feb3f3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
ffs() is 1-indexed, but we want to use it as an index into an array, so
use __ffs() instead.
Fixes: eb8d0f5af4ec ("drm/i915: Remove GPU reset dependence on struct_mutex")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315163933.19352-1-chris@chris-wilson.co.uk
(cherry picked from commit 9073e5b26743b8b675cc44a9c0c8f8c3d584e1c0)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
We rely on VBT DDI port info for eDP detection on GEN9 platforms and
above. This breaks GEN9 platforms which don't have VBT because port A
eDP now defaults to false. Fix this by defaulting to true when VBT is
missing.
Fixes: a98d9c1d7e9b ("drm/i915/ddi: Rely on VBT DDI port info for eDP detection")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190306200618.17405-1-thomas.preston@codethink.co.uk
(cherry picked from commit 2131bc0ced6088648e47f126566c3da58b07e4ef)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
In some cases, the iscsi_remove_session() function is called while an
unbind_work operation is still running. This may cause a situation where
sysfs objects are removed in an incorrect order, triggering a kernel
warning.
[ 605.249442] ------------[ cut here ]------------
[ 605.259180] sysfs group 'power' not found for kobject 'target2:0:0'
[ 605.321371] WARNING: CPU: 1 PID: 26794 at fs/sysfs/group.c:235 sysfs_remove_group+0x76/0x80
[ 605.341266] Modules linked in: dm_service_time target_core_user target_core_pscsi target_core_file target_core_iblock iscsi_target_mod target_core_mod nls_utf8 isofs ppdev bochs_drm nfit ttm libnvdimm drm_kms_helper syscopyarea sysfillrect sysimgblt joydev pcspkr fb_sys_fops drm i2c_piix4 sg parport_pc parport xfs libcrc32c dm_multipath sr_mod sd_mod cdrom ata_generic 8021q garp mrp ata_piix stp crct10dif_pclmul crc32_pclmul llc libata crc32c_intel virtio_net net_failover ghash_clmulni_intel serio_raw failover sunrpc dm_mirror dm_region_hash dm_log dm_mod be2iscsi bnx2i cnic uio cxgb4i cxgb4 libcxgbi libcxgb qla4xxx iscsi_boot_sysfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi
[ 605.627479] CPU: 1 PID: 26794 Comm: kworker/u32:2 Not tainted 4.18.0-60.el8.x86_64 #1
[ 605.721401] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20180724_192412-buildhw-07.phx2.fedoraproject.org-1.fc29 04/01/2014
[ 605.823651] Workqueue: scsi_wq_2 __iscsi_unbind_session [scsi_transport_iscsi]
[ 605.830940] RIP: 0010:sysfs_remove_group+0x76/0x80
[ 605.922907] Code: 48 89 df 5b 5d 41 5c e9 38 c4 ff ff 48 89 df e8 e0 bf ff ff eb cb 49 8b 14 24 48 8b 75 00 48 c7 c7 38 73 cb a7 e8 24 77 d7 ff <0f> 0b 5b 5d 41 5c c3 0f 1f 00 0f 1f 44 00 00 41 56 41 55 41 54 55
[ 606.122304] RSP: 0018:ffffbadcc8d1bda8 EFLAGS: 00010286
[ 606.218492] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ 606.326381] RDX: ffff98bdfe85eb40 RSI: ffff98bdfe856818 RDI: ffff98bdfe856818
[ 606.514498] RBP: ffffffffa7ab73e0 R08: 0000000000000268 R09: 0000000000000007
[ 606.529469] R10: 0000000000000000 R11: ffffffffa860d9ad R12: ffff98bdf978e838
[ 606.630535] R13: ffff98bdc2cd4010 R14: ffff98bdc2cd3ff0 R15: ffff98bdc2cd4000
[ 606.824707] FS: 0000000000000000(0000) GS:ffff98bdfe840000(0000) knlGS:0000000000000000
[ 607.018333] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 607.117844] CR2: 00007f84b78ac024 CR3: 000000002c00a003 CR4: 00000000003606e0
[ 607.117844] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 607.420926] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 607.524236] Call Trace:
[ 607.530591] device_del+0x56/0x350
[ 607.624393] ? ata_tlink_match+0x30/0x30 [libata]
[ 607.727805] ? attribute_container_device_trigger+0xb4/0xf0
[ 607.829911] scsi_target_reap_ref_release+0x39/0x50
[ 607.928572] scsi_remove_target+0x1a2/0x1d0
[ 608.017350] __iscsi_unbind_session+0xb3/0x160 [scsi_transport_iscsi]
[ 608.117435] process_one_work+0x1a7/0x360
[ 608.132917] worker_thread+0x30/0x390
[ 608.222900] ? pwq_unbound_release_workfn+0xd0/0xd0
[ 608.323989] kthread+0x112/0x130
[ 608.418318] ? kthread_bind+0x30/0x30
[ 608.513821] ret_from_fork+0x35/0x40
[ 608.613909] ---[ end trace 0b98c310c8a6138c ]---
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Now that we have alloc_size that controls our discard behavior, it
doesn't make sense to have these set to object (set) size. alloc_size
defaults to 64k, but because discard_granularity is likely 4M, only
ranges that are equal to or bigger than 4M can be considered during
fstrim. A smaller io_min is also more likely to be met, resulting in
fewer deferred writes on bluestore OSDs.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
