| Age | Commit message (Collapse) | Author |
|---|
|
gpio-mockup doesn't require SYSFS to be selected so drop that bit from
the Kconfig text.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The GPIO bank wake interrupt setting was erroneously removed after
conversion to gpio_irq_chip, thus the wake interrupt programming is
broken now. Secondly, the wake_enb of the GPIO driver should be changed
only after the successful toggling of the IRQ wake-state. Restore the wake
interrupt setting and the programming order.
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
According to the reference manual "The PCA9505 is identical to the
PCA9506 except that it includes 100 kΩ internal pull-up resistors on all
the I/Os." So the pca9506 device can be considered identical to the
pca9505 for the gpio driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add support for the GPIO controller block in the R-Car V3U (R8A779A0)
SoC, which is very similar to the block found on other R-Car Gen3 SoCs.
However, this block has a new General Input Enable Register (INEN),
whose reset state is to have all inputs disabled.
Enable input for all available pins in probe and resume, to support the
use of the General Input Register (INDT) for reading pin state at all
times. This preserves backwards compatibility with other R-Car Gen3
SoCs, as recommended by the Hardware Manual.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Currently, the R-Car GPIO driver treats R-Car Gen2 and R-Car Gen3 GPIO
controllers the same. However, there exist small differences, like the
behavior of the General Input Register (INDT):
- On R-Car Gen1, R-Car Gen2, and RZ/G1, INDT only reflects the state
of an input pin if the GPIO is configured for input,
- On R-Car Gen3 and RZ/G2, INDT always reflects the state of the input
pins.
Hence to accommodate all variants, the driver does not use the INDT
register to read the status of a GPIO line when configured for output,
at the expense of doing 2 or 3 register reads instead of 1.
Given register accesses are slow, change the .get() and .get_multiple()
callbacks to always use INDT to read pin state on SoCs where this is
supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Using a helper local variable to store the address of &pdev->dev adds
to readability and allows us to avoid unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
|
|
Convert the Tegra GPIO driver to use the gpio_irq_chip infrastructure.
This allows a bit of boiler plate to be removed and while at it enables
support for hierarchical domains, which is useful to support PMC wake
events on Tegra210 and earlier.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Add the GPIO driver for Toshiba Visconti ARM SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Reviewed-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The ROHM BD70528 and BD71828 GPIO drivers only need the regmap
pointer from parent. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The gpio-rcar driver also supports RZ/G SoC's, update the description to
reflect this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The mandatory compatible values 'renesas,rcar-gen{1,2,3}-gpio' have been
already added to all the respective R-Car Gen{1,2,3} SoC DTSI files,
remove the redundant device specific values from the driver.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
There is a spelling mistake in the Kconfig help text. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
In sdhci_esdhc_imx_remove() the SDHCI_INT_STATUS in read. Under some
circumstances, this may be done while the device is runtime suspended,
triggering the below splat.
Fix the problem by adding a pm_runtime_get_sync(), before reading the
register, which will turn on clocks etc making the device accessible again.
[ 1811.323148] mmc1: card aaaa removed
[ 1811.347483] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
[ 1811.354988] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core [last unloaded: mmc_core]
[ 1811.365726] CPU: 0 PID: 3464 Comm: rmmod Not tainted 5.10.1-sd-99871-g53835a2e8186 #5
[ 1811.373559] Hardware name: Freescale i.MX8DXL EVK (DT)
[ 1811.378705] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--)
[ 1811.384723] pc : sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx]
[ 1811.391090] lr : platform_drv_remove+0x2c/0x50
[ 1811.395536] sp : ffff800012c7bcb0
[ 1811.398855] x29: ffff800012c7bcb0 x28: ffff00002c72b900
[ 1811.404181] x27: 0000000000000000 x26: 0000000000000000
[ 1811.409497] x25: 0000000000000000 x24: 0000000000000000
[ 1811.414814] x23: ffff0000042b3890 x22: ffff800009127120
[ 1811.420131] x21: ffff00002c4c9580 x20: ffff0000042d0810
[ 1811.425456] x19: ffff0000042d0800 x18: 0000000000000020
[ 1811.430773] x17: 0000000000000000 x16: 0000000000000000
[ 1811.436089] x15: 0000000000000004 x14: ffff000004019c10
[ 1811.441406] x13: 0000000000000000 x12: 0000000000000020
[ 1811.446723] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
[ 1811.452040] x9 : fefefeff6364626d x8 : 7f7f7f7f7f7f7f7f
[ 1811.457356] x7 : 78725e6473607372 x6 : 0000000080808080
[ 1811.462673] x5 : 0000000000000000 x4 : 0000000000000000
[ 1811.467990] x3 : ffff800011ac1cb0 x2 : 0000000000000000
[ 1811.473307] x1 : ffff8000091214d4 x0 : ffff8000133a0030
[ 1811.478624] Call trace:
[ 1811.481081] sdhci_esdhc_imx_remove+0x28/0x15c [sdhci_esdhc_imx]
[ 1811.487098] platform_drv_remove+0x2c/0x50
[ 1811.491198] __device_release_driver+0x188/0x230
[ 1811.495818] driver_detach+0xc0/0x14c
[ 1811.499487] bus_remove_driver+0x5c/0xb0
[ 1811.503413] driver_unregister+0x30/0x60
[ 1811.507341] platform_driver_unregister+0x14/0x20
[ 1811.512048] sdhci_esdhc_imx_driver_exit+0x1c/0x3a8 [sdhci_esdhc_imx]
[ 1811.518495] __arm64_sys_delete_module+0x19c/0x230
[ 1811.523291] el0_svc_common.constprop.0+0x78/0x1a0
[ 1811.528086] do_el0_svc+0x24/0x90
[ 1811.531405] el0_svc+0x14/0x20
[ 1811.534461] el0_sync_handler+0x1a4/0x1b0
[ 1811.538474] el0_sync+0x174/0x180
[ 1811.541801] Code: a9025bf5 f9403e95 f9400ea0 9100c000 (b9400000)
[ 1811.547902] ---[ end trace 3fb1a3bd48ff7be5 ]---
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Cc: stable@vger.kernel.org # v4.0+
Link: https://lore.kernel.org/r/20210210181933.29263-1-Frank.Li@nxp.com
[Ulf: Clarified the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Android Studio Emulator no longer uses this driver, so let's drop it.
Signed-off-by: Roman Kiryanov <rkir@google.com>
Link: https://lore.kernel.org/r/20210209190850.16647-1-rkir@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This converts the driver to use the new tasklet API introduced in
commit 12cc923f1ccc ("tasklet: Introduce new initialization API")
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/20210208134551.39696-1-kernel@esmil.dk
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Force chip enter L0 power state during SDR104 HW tuning to avoid tuning failure
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Link: https://lore.kernel.org/r/20210206014051.3418-1-shirley.her@bayhubtech.com
Fixes: 7b7d897e8898 ("mmc: sdhci-pci-o2micro: Add HW tuning for SDR104 mode")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
The function uses a goto-based loop, which may lead to an earlier error
getting discarded by a later iteration. Exit this ad-hoc loop when an
error was encountered.
The out-of-memory error path additionally fails to fill a structure
field looked at by xen_blkbk_unmap_prepare() before inspecting the
handle which does get properly set (to BLKBACK_INVALID_HANDLE).
Since the earlier exiting from the ad-hoc loop requires the same field
filling (invalidation) as that on the out-of-memory path, fold both
paths. While doing so, drop the pr_alert(), as extra log messages aren't
going to help the situation (the kernel will log oom conditions already
anyway).
This is XSA-365.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
In particular -ENOMEM may come back here, from set_foreign_p2m_mapping().
Don't make problems worse, the more that handling elsewhere (together
with map's status fields now indicating whether a mapping wasn't even
attempted, and hence has to be considered failed) doesn't require this
odd way of dealing with errors.
This is part of XSA-362.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Failure of the kernel part of the mapping operation should also be
indicated as an error to the caller, or else it may assume the
respective kernel VA is okay to access.
Furthermore gnttab_map_refs() failing still requires recording
successfully mapped handles, so they can be unmapped subsequently. This
in turn requires there to be a way to tell full hypercall failure from
partial success - preset map_op status fields such that they won't
"happen" to look as if the operation succeeded.
Also again use GNTST_okay instead of implying its value (zero).
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
We may not skip setting the field in the unmap structure when
GNTMAP_device_map is in use - such an unmap would fail to release the
respective resources (a page ref in the hypervisor). Otoh the field
doesn't need setting at all when GNTMAP_device_map is not in use.
To record the value for unmapping, we also better don't use our local
p2m: In particular after a subsequent change it may not have got updated
for all the batch elements. Instead it can simply be taken from the
respective map's results.
We can additionally avoid playing this game altogether for the kernel
part of the mappings in (x86) PV mode.
This is part of XSA-361.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: stable@vger.kernel.org
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
There is a specific API to treat raw data as GUID, i.e. export_guid()
and import_guid(). Use them instead of guid_copy() with explicit casting.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove NULL checks before vfree() to fix these warnings:
./drivers/lightnvm/pblk-gc.c:27:2-7: WARNING: NULL check before some
freeing functions is not needed.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Matias Bjørling <matias.bjorling@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
GENCONF_CTRL0_PORTX naming improved.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use PTR_ERR_OR_ZERO instead of IS_ERR and PTR_ERR.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use >= MVPP22 instead of != MVPP21.
Non functional change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PPv2.1 contain 0 in Version ID register, priv->hw_version check
can be removed.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers can't dynamically change the VLAN filtering option, or
impose some restrictions, it would be nice to propagate this info
through netlink instead of printing it to a kernel log that might never
be read. Also netlink extack includes the module that emitted the
message, which means that it's easier to figure out which ones are
driver-generated errors as opposed to command misuse.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow drivers to communicate their restrictions to user space directly,
instead of printing to the kernel log. Where the conversion would have
been lossy and things like VLAN ID could no longer be conveyed (due to
the lack of support for printf format specifier in netlink extack), I
chose to keep the messages in full form to the kernel log only, and
leave it up to individual driver maintainers to move more messages to
extack.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.
felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.
Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.
On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).
This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.
The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.
There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the tag_8021q tagger is software-defined, it has no means by
itself for retrieving hardware timestamps of PTP event messages.
Because we do want to support PTP on ocelot even with tag_8021q, we need
to use the CPU port module for that. The RX timestamp is present in the
Extraction Frame Header. And because we can't use NPI mode which redirects
the CPU queues to an "external CPU" (meaning the ARM CPU running Linux),
then we need to poll the CPU port module through the MMIO registers to
retrieve TX and RX timestamps.
Sadly, on NXP LS1028A, the Felix switch was integrated into the SoC
without wiring the extraction IRQ line to the ARM GIC. So, if we want to
be notified of any PTP packets received on the CPU port module, we have
a problem.
There is a possible workaround, which is to use the Ethernet CPU port as
a notification channel that packets are available on the CPU port module
as well. When a PTP packet is received by the DSA tagger (without timestamp,
of course), we go to the CPU extraction queues, poll for it there, then
we drop the original Ethernet packet and masquerade the packet retrieved
over MMIO (plus the timestamp) as the original when we inject it up the
stack.
Create a quirk in struct felix is selected by the Felix driver (but not
by Seville, since that doesn't support PTP at all). We want to do this
such that the workaround is minimally invasive for future switches that
don't require this workaround.
The only traffic for which we need timestamps is PTP traffic, so add a
redirection rule to the CPU port module for this. Currently we only have
the need for PTP over L2, so redirection rules for UDP ports 319 and 320
are TBD for now.
Note that for the workaround of matching of PTP-over-Ethernet-port with
PTP-over-MMIO queues to work properly, both channels need to be
absolutely lossless. There are two parts to achieving that:
- We keep flow control enabled on the tag_8021q CPU port
- We put the DSA master interface in promiscuous mode, so it will never
drop a PTP frame (for the profiles we are interested in, these are
sent to the multicast MAC addresses of 01-80-c2-00-00-0e and
01-1b-19-00-00-00).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.
We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot tagger is a hot mess currently, it relies on memory
initialized by the attached driver for basic frame transmission.
This is against all that DSA tagging protocols stand for, which is that
the transmission and reception of a DSA-tagged frame, the data path,
should be independent from the switch control path, because the tag
protocol is in principle hot-pluggable and reusable across switches
(even if in practice it wasn't until very recently). But if another
driver like dsa_loop wants to make use of tag_ocelot, it couldn't.
This was done to have common code between Felix and Ocelot, which have
one bit difference in the frame header format. Quoting from commit
67c2404922c2 ("net: dsa: felix: create a template for the DSA tags on
xmit"):
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
The really interesting part is that Seville should have had its own
tagging protocol defined - it is not compatible on the wire with Ocelot,
even for that single bit. In principle, a packet generated by
DSA_TAG_PROTO_OCELOT when booted on NXP LS1028A would look in a certain
way, but when booted on NXP T1040 it would look differently. The reverse
is also true: a packet generated by a Seville switch would be
interpreted incorrectly by Wireshark if it was told it was generated by
an Ocelot switch.
Actually things are a bit more nuanced. If we concentrate only on the
DSA tag, what I said above is true, but Ocelot/Seville also support an
optional DSA tag prefix, which can be short or long, and it is possible
to distinguish the two taggers based on an integer constant put in that
prefix. Nonetheless, creating a separate tagger is still justified,
since the tag prefix is optional, and without it, there is again no way
to distinguish.
Claiming backwards binary compatibility is a bit more tough, since I've
already changed the format of tag_ocelot once, in commit 5124197ce58b
("net: dsa: tag_ocelot: use a short prefix on both ingress and egress").
Therefore I am not very concerned with treating this as a bugfix and
backporting it to stable kernels (which would be another mess due to the
fact that there would be lots of conflicts with the other DSA_TAG_PROTO*
definitions). It's just simpler to say that the string values of the
taggers have ABI value starting with kernel 5.12, which will be when the
changing of tag protocol via /sys/class/net/<dsa-master>/dsa/tagging
goes live.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.
Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).
The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.
Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This looks a bit nicer than the open-coded "(x + 3) % 4" idiom.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot_rx_frame_word() function can return a negative error code,
however this isn't being checked for consistently. Errors being ignored
have not been seen in practice though.
Also, some constructs can be simplified by using "goto" instead of
repeated "break" statements.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It appears that the intention of this snippet of code is to not exit
ocelot_xtr_irq_handler() while in the middle of extracting a frame.
The problem in extracting it word by word is that future extraction
attempts are really easy to get desynchronized, since the IRQ handler
assumes that the first 16 bytes are the IFH, which give further
information about the frame, such as frame length.
But during normal operation, "err" will not be 0, but 4, set from here:
for (i = 0; i < OCELOT_TAG_LEN / 4; i++) {
err = ocelot_rx_frame_word(ocelot, grp, true, &ifh[i]);
if (err != 4)
break;
}
if (err != 4)
break;
In that case, draining the extraction queue is a no-op. So explicitly
make this code execute only on negative err.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the xtr (extraction) IRQ of the ocelot switch is not shared, then
if it fired, it means that some data must be present in the queues of
the CPU port module. So simplify the code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a new async message that the firmware can send to check if it
can communicate with the driver. This is an added error detection
scheme that firmware can use if it suspects errors in the PCIe
interface. When the driver receives this async message, it will reply
back echoing some data in the async message. If the firmware is not
getting the reply with the proper data after some retries, error
recovery will kick in.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware provides the offset to the "context kind" field of the
relevant context memory blocks, we'll initialize just that field for
each block instead of initializing all of context memory.
Populate the bnxt_mem_init structure with the proper offset returned
by firmware. If it is older firmware and the information is not
available, we set the offset to an invalid value and fall back to
the old behavior of initializing every byte. Otherwise, we initialize
only the "context kind" byte at the offset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
