| Age | Commit message (Collapse) | Author |
|---|
|
The previous implementation of .handle_interrupt() did not take into
account the fact that all the interrupt status registers should be
acknowledged since multiple interrupt sources could be asserted.
Fix this by reading all the status registers before exiting with
IRQ_NONE or triggering the PHY state machine.
Fixes: 1d1ae3c6ca3f ("net: phy: ti: implement generic .handle_interrupt() callback")
Reported-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20210226153020.867852-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Set err to -ENOMEM if kzalloc fails instead of 0.
Fixes: 759738537142 ("IB/mlx5: Enable subscription for device events over DEVX")
Link: https://lore.kernel.org/r/20210222122343.19720-1-yuehaibing@huawei.com
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
When RDMA_RXE is enabled and CRYPTO is disabled, Kbuild gives the
following warning:
WARNING: unmet direct dependencies detected for CRYPTO_CRC32
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- RDMA_RXE [=y] && (INFINIBAND_USER_ACCESS [=y] || !INFINIBAND_USER_ACCESS [=y]) && INET [=y] && PCI [=y] && INFINIBAND [=y] && INFINIBAND_VIRT_DMA [=y]
This is because RDMA_RXE selects CRYPTO_CRC32, without depending on or
selecting CRYPTO, despite that config option being subordinate to CRYPTO.
Fixes: cee2688e3cd6 ("IB/rxe: Offload CRC calculation when possible")
Signed-off-by: Julian Braha <julianbraha@gmail.com>
Link: https://lore.kernel.org/r/21525878.NYvzQUHefP@ubuntu-mate-laptop
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
ib_send_cm_sidr_rep() {
spin_lock_irqsave()
cm_send_sidr_rep_locked() {
...
spin_lock_irq()
....
spin_unlock_irq() <--- this will enable interrupts
}
spin_unlock_irqrestore()
}
spin_unlock_irqrestore() expects interrupts to be disabled but the
internal spin_unlock_irq() will always enable hard interrupts.
Fix this by replacing the internal spin_{lock,unlock}_irq() with
irqsave/restore variants.
It fixes the following kernel trace:
raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 2 PID: 20001 at kernel/locking/irqflag-debug.c:10 warn_bogus_irq_restore+0x1d/0x20
Call Trace:
_raw_spin_unlock_irqrestore+0x4e/0x50
ib_send_cm_sidr_rep+0x3a/0x50 [ib_cm]
cma_send_sidr_rep+0xa1/0x160 [rdma_cm]
rdma_accept+0x25e/0x350 [rdma_cm]
ucma_accept+0x132/0x1cc [rdma_ucm]
ucma_write+0xbf/0x140 [rdma_ucm]
vfs_write+0xc1/0x340
ksys_write+0xb3/0xe0
do_syscall_64+0x2d/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 87c4c774cbef ("RDMA/cm: Protect access to remote_sidr_table")
Link: https://lore.kernel.org/r/20210301081844.445823-1-leon@kernel.org
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
The DTPM framework will evolve in the next cycles. Let's add a
temporary EXPERIMENTAL tag to the option so users will be aware
the API may change over time.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The root node is not set to NULL when the dtpm root node is
removed. Consequently, it is not possible to create a new root
as it is already set.
Set the root node to NULL when the last node is removed.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by rpm_put_suppliers() called by it may fail.
Fix this by making __rpm_callback() update the device's status to
RPM_SUSPENDED before calling rpm_put_suppliers() if the current
status of the device is RPM_SUSPENDING and the callback just invoked
by it has returned 0 (success).
While at it, modify the code in __rpm_callback() to always check
the device's PM-runtime status under its PM lock.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/
Fixes: 21d5c57b3726 ("PM / runtime: Use device links")
Reported-by: Elaine Zhang <zhangqing@rock-chips.com>
Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Elaine Zhang <zhangiqng@rock-chips.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
entering Normal Mode
This patch prevents a potentially destructive race condition. The
device is fully operational on the bus after entering Normal Mode, so
zeroing the MRAM after entering this mode may lead to loss of
information, e.g. new received messages.
This patch fixes the problem by first initializing the MRAM, then
bringing the device into Normale Mode.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: https://lore.kernel.org/r/20210226163440.313628-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In the following 4 patches
| 99842c9685ab can: dev: can_rx_offload_get_echo_skb(): extend to return can frame length
| 9420e1d495e2 can: dev: can_get_echo_skb(): extend to return can frame length
| 1dcb6e57db83 can: dev: can_put_echo_skb(): extend to handle frame_len
| f0ef72febc9a can: dev: extend struct can_skb_priv to hold CAN frame length
the CAN echo SKB support was extended to hold the CAN frame
length (which is the length of the CAN frame on the wire). It is meant
as a helper for BQL support, to avoid the re-calculation of the frame
length before sending it and on TX-completion.
However if the CAN frame is send without the request to be looped back
the SKB is discarded in can_put_echo_skb() and the subsequent
can_get_echo_skb() and can_rx_offload_get_echo_skb() return 0 for the
CAN frame length. This results in BQL stalling the TX queue after a
few packages.
Until the BQL helpers can_get_echo_skb() and
can_rx_offload_get_echo_skb() are fixed, revert the BQL support for
the mcp251xfd driver.
This reverts commit 4162e18e949ba520d5116ac0323500355479a00e.
Fixes: 4162e18e949b ("can: mcp251xfd: add BQL support")
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20210228083347.28580-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Invoke flexcan_chip_freeze() to enter freeze mode, since need poll
freeze mode acknowledge.
Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-4-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
RX FIFO enable failed could happen when do system reboot stress test:
[ 0.303958] flexcan 5a8d0000.can: 5a8d0000.can supply xceiver not found, using dummy regulator
[ 0.304281] flexcan 5a8d0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.314640] flexcan 5a8d0000.can: registering netdev failed
[ 0.320728] flexcan 5a8e0000.can: 5a8e0000.can supply xceiver not found, using dummy regulator
[ 0.320991] flexcan 5a8e0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.331360] flexcan 5a8e0000.can: registering netdev failed
[ 0.337444] flexcan 5a8f0000.can: 5a8f0000.can supply xceiver not found, using dummy regulator
[ 0.337716] flexcan 5a8f0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[ 0.348117] flexcan 5a8f0000.can: registering netdev failed
RX FIFO should be enabled after the FRZ/HALT are valid. But the current
code enable RX FIFO and FRZ/HALT at the same time.
Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-3-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a2165b ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
By having selected DRM_XEN, I was assuming I would build the frontend
driver. As it turns out this is a dummy option, and I have really not
been building this (because I had DRM disabled). Make it a promptless
one, moving the "depends on" to the other, real option, and "select"ing
the dummy one.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://patchwork.freedesktop.org/patch/msgid/54ae54f9-1ba9-900b-a56f-f48e2c9a82b0@suse.com
|
|
s/negtive/negative/
s/possilbe/possible/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210222081838.30328-1-unixbhaskar@gmail.com
|
|
Current vblank emulator uses single hrtimer at 16ms period for all vGPUs,
which introduces three major issues:
- 16ms matches the refresh rate at 62.5Hz (instead of 60Hz) which
doesn't follow standard timing. This leads to some frame drop or glitch
issue during video playback. SW expects a vsync interval of 16.667ms or
higher precision for an accurate 60Hz refresh rate. However current
vblank emulator only works at 16ms.
- Doesn't respect the fact that with current virtual EDID timing set,
not all resolutions are running at 60Hz. For example, current virtual
EDID also supports refresh rate at 56Hz, 59.97Hz, 60Hz, 75Hz, etc.
- Current vblank emulator use single hrtimer for all vGPUs. Regardsless
the possibility that different guests could run in different
resolutions, all vsync interrupts are injected at 16ms interval with
same hrtimer.
Based on previous patch which decode guest expected refresh rate from
vreg, the vblank emulator refactor patch makes following changes:
- Change the vblank emulator hrtimer from gvt global to per-vGPU.
By doing this, each vGPU display can operates at different refresh
rates. Currently only one dislay is supported for each vGPU so per-vGPU
hrtimer is enough. If multiple displays are supported per-vGPU in
future, we can expand to per-PIPE further.
- Change the fixed hrtimer period from 16ms to dynamic based on vreg.
GVT is expected to emulate the HW as close as possible. So reflacting
the accurate vsync interrupt interval is more correct than fixed 16ms.
- Change the vblank timer period and start the timer on PIPECONF change.
The initial period is updated to 16666667 based on 60Hz refresh rate.
According to PRM, PIPECONF controls the timing generator of the
connected display on this pipe, so it's safe to stop hrtimer on
PIPECONF disabling, and re-start hrtimer at new period on enabling.
Other changes including:
- Move vblank_timer_fn from irq.c into display.c.
- Clean per-vGPU vblank timer at clean_display instead of clean_irq.
To run quick test, launch a web browser and goto URL: www.displayhz.com
The actual refresh rate from guest can now always match guest settings.
V2:
Rebase to 5.11.
Remove unused intel_gvt_clean_irq().
Simplify enable logic in update_vblank_emulation(). (zhenyu)
Loop all vGPU by idr when check all vblank timer. (zhenyu)
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210226044630.284269-1-colin.xu@intel.com
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Guest OS builds up its timing mode list based on the virtual EDID as
simulated by GVT. However since there are several timings supported in
the virtual EDID, and each timing can also support several modes
(resolution and refresh rate), current emulated vblank period (16ms)
may not always be correct and could lead to miss-sync behavior in guest.
Guest driver will setup new resolution and program vregs accordingly and
it should always follows GEN PRM. Based on the simulated display regs by
GVT, it's safe to decode the actual refresh rate using by guest from
vreg only.
Current implementation only enables PIPE_A and PIPE_A is always tied to
TRANSCODER_A in HW. GVT may simulate DP monitor on PORT_B or PORT_D
based on the caller. So we can find out which DPLL is used by PORT_x
which connected to TRANSCODER_A and calculate the DP bit rate from the
DPLL frequency. Then DP stream clock (pixel clock) can be calculated
from DP link M/N and DP bit rate. Finally, get the refresh rate from
pixel clock, H total and V total.
The per-vGPU accurate refresh rate is not used yet but only stored,
until per-vGPU vblank timer is enabled. Then each vGPU can have
different and accurate refresh rate per-guest driver configuration.
Refer to PRM for GEN display and VESA timing standard for more details.
V2:
Rebase to 5.11.
Correctly calculate DP link rate for BDW and BXT.
Use GVT_DEFAULT_REFRESH_RATE instead of hardcoded to 60 as init refresh.
Typo fix. (zhenyu)
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210226044559.283622-1-colin.xu@intel.com
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Pull ide fix from Jens Axboe:
"This is a leftover fix from 5.11, where I forgot to ship it your way"
* tag 'ide-5.11-2021-02-28' of git://git.kernel.dk/linux-block:
ide/falconide: Fix module unload
|
|
The function hclge_fd_convert_tuple() is used to convert tuples
and tuples mask to TCAM x and y. But it misuses the source mac
as source mac mask when convert INNER_SRC_MAC, which may cause
the flow director rule works unexpectedly. So fix it.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, the driver returns VLAN_VID_MASK for vlan mask field,
when get flow director rule information for rule doesn't use vlan.
It may cause the vlan mask value display as 0xf000 in this
case, like below:
estuary:/$ ethtool -u eth1
50 RX rings available
Total 1 rules
Filter: 2
Rule Type: TCP over IPv4
Src IP addr: 0.0.0.0 mask: 255.255.255.255
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xf000
User-defined: 0x1234 mask: 0x0
Action: Direct to queue 3
Fix it by return 0.
Fixes: 05c2314fe6a8 ("net: hns3: Add support for rule query of flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, some bit filed definitions of flow director TCAM
configuration command are incorrect. Since the wrong MSB is
always 0, and these fields are assgined in order, so it still works.
Fix it by redefine them.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When receiving a lot of packets hardware may run out of free
descriptiors and stop RX ring. Enable it every time after handling
received packets.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210226132038.29849-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull more SCSI updates from James Bottomley:
"This is a few driver updates (iscsi, mpt3sas) that were still in the
staging queue when the merge window opened (all committed on or before
8 Feb) and some small bug fixes which came in during the merge window
(all committed on 22 Feb)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (30 commits)
scsi: hpsa: Correct dev cmds outstanding for retried cmds
scsi: sd: Fix Opal support
scsi: target: tcmu: Fix memory leak caused by wrong uio usage
scsi: target: tcmu: Move some functions without code change
scsi: sd: sd_zbc: Don't pass GFP_NOIO to kvcalloc
scsi: aic7xxx: Remove unused function pointer typedef ahc_bus_suspend/resume_t
scsi: bnx2fc: Fix Kconfig warning & CNIC build errors
scsi: ufs: Fix a duplicate dev quirk number
scsi: aic79xx: Fix spelling of version
scsi: target: core: Prevent underflow for service actions
scsi: target: core: Add cmd length set before cmd complete
scsi: iscsi: Drop session lock in iscsi_session_chkready()
scsi: qla4xxx: Use iscsi_is_session_online()
scsi: libiscsi: Reset max/exp cmdsn during recovery
scsi: iscsi_tcp: Fix shost can_queue initialization
scsi: libiscsi: Add helper to calculate max SCSI cmds per session
scsi: libiscsi: Fix iSCSI host workq destruction
scsi: libiscsi: Fix iscsi_task use after free()
scsi: libiscsi: Drop taskqueuelock
scsi: libiscsi: Fix iscsi_prep_scsi_cmd_pdu() error handling
...
|
|
Pull more block updates from Jens Axboe:
"A few stragglers (and one due to me missing it originally), and fixes
for changes in this merge window mostly. In particular:
- blktrace cleanups (Chaitanya, Greg)
- Kill dead blk_pm_* functions (Bart)
- Fixes for the bio alloc changes (Christoph)
- Fix for the partition changes (Christoph, Ming)
- Fix for turning off iopoll with polled IO inflight (Jeffle)
- nbd disconnect fix (Josef)
- loop fsync error fix (Mauricio)
- kyber update depth fix (Yang)
- max_sectors alignment fix (Mikulas)
- Add bio_max_segs helper (Matthew)"
* tag 'block-5.12-2021-02-27' of git://git.kernel.dk/linux-block: (21 commits)
block: Add bio_max_segs
blktrace: fix documentation for blk_fill_rw()
block: memory allocations in bounce_clone_bio must not fail
block: remove the gfp_mask argument to bounce_clone_bio
block: fix bounce_clone_bio for passthrough bios
block-crypto-fallback: use a bio_set for splitting bios
block: fix logging on capacity change
blk-settings: align max_sectors on "logical_block_size" boundary
block: reopen the device in blkdev_reread_part
block: don't skip empty device in in disk_uevent
blktrace: remove debugfs file dentries from struct blk_trace
nbd: handle device refs for DESTROY_ON_DISCONNECT properly
kyber: introduce kyber_depth_updated()
loop: fix I/O error on fsync() in detached loop devices
block: fix potential IO hang when turning off io_poll
block: get rid of the trace rq insert wrapper
blktrace: fix blk_rq_merge documentation
blktrace: fix blk_rq_issue documentation
blktrace: add blk_fill_rwbs documentation comment
block: remove superfluous param in blk_fill_rwbs()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff pile - no common topic here"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
whack-a-mole: don't open-code iminor/imajor
9p: fix misuse of sscanf() in v9fs_stat2inode()
audit_alloc_mark(): don't open-code ERR_CAST()
fs/inode.c: make inode_init_always() initialize i_ino to 0
vfs: don't unnecessarily clone write access for writable fds
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three more bugfixes and one revert. I accidently applied one patch too
early"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: exynos5: Preserve high speed master code
Revert "i2c: i2c-qcom-geni: Add shutdown callback for i2c"
i2c: designware: Get right data length
i2c: brcmstb: Fix brcmstd_send_i2c_cmd condition
|
|
The following trace excerpt corresponds with a NULL pointer dereference
of 'bp->irq_tbl' in bnxt_setup_inta() on an Aarch64 system after many
device resets:
Unable to handle kernel NULL pointer dereference at ... 000000d
...
pc : string+0x3c/0x80
lr : vsnprintf+0x294/0x7e0
sp : ffff00000f61ba70 pstate : 20000145
x29: ffff00000f61ba70 x28: 000000000000000d
x27: ffff0000009c8b5a x26: ffff00000f61bb80
x25: ffff0000009c8b5a x24: 0000000000000012
x23: 00000000ffffffe0 x22: ffff000008990428
x21: ffff00000f61bb80 x20: 000000000000000d
x19: 000000000000001f x18: 0000000000000000
x17: 0000000000000000 x16: ffff800b6d0fb400
x15: 0000000000000000 x14: ffff800b7fe31ae8
x13: 00001ed16472c920 x12: ffff000008c6b1c9
x11: ffff000008cf0580 x10: ffff00000f61bb80
x9 : 00000000ffffffd8 x8 : 000000000000000c
x7 : ffff800b684b8000 x6 : 0000000000000000
x5 : 0000000000000065 x4 : 0000000000000001
x3 : ffff0a00ffffff04 x2 : 000000000000001f
x1 : 0000000000000000 x0 : 000000000000000d
Call trace:
string+0x3c/0x80
vsnprintf+0x294/0x7e0
snprintf+0x44/0x50
__bnxt_open_nic+0x34c/0x928 [bnxt_en]
bnxt_open+0xe8/0x238 [bnxt_en]
__dev_open+0xbc/0x130
__dev_change_flags+0x12c/0x168
dev_change_flags+0x20/0x60
...
Ordinarily, a call to bnxt_setup_inta() (not in trace due to inlining)
would not be expected on a system supporting MSIX at all. However, if
bnxt_init_int_mode() does not end up being called after the call to
bnxt_clear_int_mode() in bnxt_fw_reset_close(), then the driver will
think that only INTA is supported and bp->irq_tbl will be NULL,
causing the above crash.
In the error recovery scenario, we call bnxt_clear_int_mode() in
bnxt_fw_reset_close() early in the sequence. Ordinarily, we will
call bnxt_init_int_mode() in bnxt_hwrm_if_change() after we
reestablish communication with the firmware after reset. However,
if the sequence has to abort before we call bnxt_init_int_mode() and
if the user later attempts to re-open the device, then it will cause
the crash above.
We fix it in 2 ways:
1. Check for bp->irq_tbl in bnxt_setup_int_mode(). If it is NULL, call
bnxt_init_init_mode().
2. If we need to abort in bnxt_hwrm_if_change() and cannot complete
the error recovery sequence, set the BNXT_STATE_ABORT_ERR flag. This
will cause more drastic recovery at the next attempt to re-open the
device, including a call to bnxt_init_int_mode().
Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver's error recovery reset sequence can take many seconds to
complete and only the critical sections are protected by rtnl_lock.
A recent change has introduced a regression in this sequence.
bnxt_remove_one() may be called while the recovery is in progress.
Normally, unregister_netdev() would cause bnxt_close_nic() to be
called and this would cause the error recovery to safely abort
with the BNXT_STATE_ABORT_ERR flag set in bnxt_close_nic().
Recently, we added bnxt_reinit_after_abort() to allow the user to
reopen the device after an aborted recovery. This causes the
regression in the scenario described above because we would
attempt to re-open even after the netdev has been unregistered.
Fix it by checking the netdev reg_state in
bnxt_reinit_after_abort() and abort if it is unregistered.
Fixes: 6882c36cf82e ("bnxt_en: attempt to reinitialize after aborted reset")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Routes are currently processed from a workqueue whereas nexthop objects
are processed in system call context. This can result in the driver not
finding a suitable nexthop group for a route and issuing a warning [1].
Fix this by ignoring such routes earlier in the process. The subsequent
deletion notification will be ignored as well.
[1]
WARNING: CPU: 2 PID: 7754 at drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4853 mlxsw_sp_router_fib_event_work+0x1112/0x1e00 [mlxsw_spectrum]
[...]
CPU: 2 PID: 7754 Comm: kworker/u8:0 Not tainted 5.11.0-rc6-cq-20210207-1 #16
Hardware name: Mellanox Technologies Ltd. MSN2100/SA001390, BIOS 5.6.5 05/24/2018
Workqueue: mlxsw_core_ordered mlxsw_sp_router_fib_event_work [mlxsw_spectrum]
RIP: 0010:mlxsw_sp_router_fib_event_work+0x1112/0x1e00 [mlxsw_spectrum]
Fixes: cdd6cfc54c64 ("mlxsw: spectrum_router: Allow programming routes with nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reported-by: Alex Veber <alexve@nvidia.com>
Tested-by: Alex Veber <alexve@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, only external bits are added to the PTYS register, whereas
there is one external bit that is wrongly marked as internal, and so was
recently removed from the register.
Add that bit to the PTYS register again, as this bit is no longer
internal.
Its removal resulted in '100000baseLR4_ER4/Full' link mode no longer
being supported, causing a regression on some setups.
Fixes: 5bf01b571cf4 ("mlxsw: spectrum_ethtool: Remove internal speeds from PTYS register")
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reported-by: Eddie Shklaer <eddies@nvidia.com>
Tested-by: Eddie Shklaer <eddies@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When accessing the timecounter register on an i.MX8MQ the kernel hangs.
This is only the case when the interface is down. This can be reproduced
by reading with 'phc_ctrl eth0 get'.
Like described in the change in 91c0d987a9788dcc5fe26baafd73bf9242b68900
the igp clock is disabled when the interface is down and leads to a
system hang.
So we check if the ptp clock status before reading the timecounter
register.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20210225211514.9115-1-heiko.thiery@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When CONFIG_PM_SLEEP is disabled, the compiler warns about unused
functions:
drivers/net/phy/phy_device.c:273:12: error: unused function 'mdio_bus_phy_suspend' [-Werror,-Wunused-function]
static int mdio_bus_phy_suspend(struct device *dev)
drivers/net/phy/phy_device.c:293:12: error: unused function 'mdio_bus_phy_resume' [-Werror,-Wunused-function]
static int mdio_bus_phy_resume(struct device *dev)
The logic is intentional, so just mark these two as __maybe_unused
and remove the incorrect #ifdef.
Fixes: 4c0d2e96ba05 ("net: phy: consider that suspend2ram may cut off PHY power")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210225145748.404410-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The new GPIO support may be optional at runtime, but it requires
building against gpiolib:
ERROR: modpost: "gpiochip_get_data" [drivers/net/dsa/mt7530.ko]
undefined!
ERROR: modpost: "devm_gpiochip_add_data_with_key"
[drivers/net/dsa/mt7530.ko] undefined!
Add #ifdef to exclude GPIO support if GPIOLIB is not enabled.
Fixes: 429a0edeefd8 ("net: dsa: mt7530: MT7530 optional GPIO support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20210226063226.8474-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Without this option, the driver fails to link:
ld.lld: error: undefined symbol: devlink_sb_register
>>> referenced by ocelot_devlink.c
>>> net/ethernet/mscc/ocelot_devlink.o:(ocelot_devlink_sb_register) in archive drivers/built-in.a
>>> referenced by ocelot_devlink.c
>>> net/ethernet/mscc/ocelot_devlink.o:(ocelot_devlink_sb_register) in archive drivers/built-in.a
Fixes: f59fd9cab730 ("net: mscc: ocelot: configure watermarks using devlink-sb")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210225143910.3964364-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During suspend/resume stress test, we found descriptor write back by DMA
could exhibit unusual behavior, e.g.:
003 [0xc4310030]: 0x0 0x40 0x0 0xb5010040
We can see that desc3 write back is 0xb5010040, it is still ownd by DMA,
so application would not recycle this buffer. It will trigger fatal bus
error when DMA try to use this descriptor again. To fix this issue, we
should re-init all rx buffers when mac resume back.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In current driver, buffer2 available only when hardware supports split
header. Wrongly set buffer2 valid in stmmac_rx_refill when refill buffer
address. You can see that desc3 is 0x81000000 after initialization, but
turn out to be 0x83000000 after refill.
Fixes: 67afd6d1cfdf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Driver uses dma_alloc_coherent to allocate dma memory for descriptors,
dma_alloc_coherent will return both the virtual address and physical
address. AFAIK, virt_to_phys could not convert virtual address to
physical address, for which memory is allocated by dma_alloc_coherent.
dwmac4_display_ring() function is broken for various descriptor, it only
support normal descriptor(struct dma_desc) now, this patch also extends to
support all descriptor types.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
stmmac_xmit() call stmmac_tx_timer_arm() at the end to modify tx timer to
do the transmission cleanup work. Imagine such a situation, stmmac enters
suspend immediately after tx timer modified, it's expire callback
stmmac_tx_clean() would not be invoked. This could affect BQL, since
netdev_tx_sent_queue() has been called, but netdev_tx_completed_queue()
have not been involved, as a result, dql_avail(&dev_queue->dql) finally
always return a negative value.
__dev_queue_xmit->__dev_xmit_skb->qdisc_run->__qdisc_run->qdisc_restart->dequeue_skb:
if ((q->flags & TCQ_F_ONETXQUEUE) &&
netif_xmit_frozen_or_stopped(txq)) // __QUEUE_STATE_STACK_XOFF is set
Net core will stop transmitting any more. Finillay, net watchdong would timeout.
To fix this issue, we should call netdev_tx_reset_queue() in stmmac_resume().
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If clear GMAC_CONFIG_TE bit, it would stop all tx channels, but users
may only want to stop specific tx channel.
Fixes: 48863ce5940f ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It's often inconvenient to use BIO_MAX_PAGES due to min() requiring the
sign to be the same. Introduce bio_max_segs() and change BIO_MAX_PAGES to
be unsigned to make it easier for the users.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes, nothing all that
notable"
* tag 'docs-5.12-2' of git://git.lwn.net/linux:
docs: proc.rst: fix indentation warning
Documentation: cgroup-v2: fix path to example BPF program
docs: powerpc: Fix tables in syscall64-abi.rst
Documentation: features: refresh feature list
Documentation: features: remove c6x references
docs: ABI: testing: ima_policy: Fixed missing bracket
Fix unaesthetic indentation
scripts: kernel-doc: fix array element capture in pointer-to-func parsing
doc: use KCFLAGS instead of EXTRA_CFLAGS to pass flags from command line
Documentation: proc.rst: add more about the 6 fields in loadavg
|
|
Pull OpenRISC updates from Stafford Horne:
- Update for Litex SoC controller to support wider width registers as
well as reset.
- Refactor SMP code to use device tree to define possible cpus.
- Update build including generating vmlinux.bin
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: Use devicetree to determine present cpus
drivers/soc/litex: Add restart handler
openrisc: add arch/openrisc/Kbuild
drivers/soc/litex: make 'litex_[set|get]_reg()' methods private
drivers/soc/litex: support 32-bit subregisters, 64-bit CPUs
drivers/soc/litex: s/LITEX_REG_SIZE/LITEX_SUBREG_ALIGN/g
drivers/soc/litex: separate MMIO from subregister offset calculation
drivers/soc/litex: move generic accessors to litex.h
openrisc: restart: Call common handlers before hanging
openrisc: Add vmlinux.bin target
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Fix physical vs virtual confusion in some basic mm macros and
routines. Caused by __pa == __va on s390 currently.
- Get rid of on-stack cpu masks.
- Add support for complete CPU counter set extraction.
- Add arch_irq_work_raise implementation.
- virtio-ccw revision and opcode fixes.
* tag 's390-5.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cpumf: Add support for complete counter set extraction
virtio/s390: implement virtio-ccw revision 2 correctly
s390/smp: implement arch_irq_work_raise()
s390/topology: move cpumasks away from stack
s390/smp: smp_emergency_stop() - move cpumask away from stack
s390/smp: __smp_rescan_cpus() - move cpumask away from stack
s390/smp: consolidate locking for smp_rescan()
s390/mm: fix phys vs virt confusion in vmem_*() functions family
s390/mm: fix phys vs virt confusion in pgtable allocation routines
s390/mm: fix invalid __pa() usage in pfn_pXd() macros
s390/mm: make pXd_deref() macros return a pointer
s390/opcodes: rename selhhhr to selfhr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb
Pull swiotlb updates from Konrad Rzeszutek Wilk:
"Two memory encryption related patches (SWIOTLB is enabled by default
for AMD-SEV):
- Add support for alignment so that NVME can properly work
- Keep track of requested DMA buffers length, as underlaying hardware
devices can trip SWIOTLB to bounce too much and crash the kernel
And a tiny fix to use proper APIs in drivers"
* 'stable/for-linus-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb:
swiotlb: Validate bounce size in the sync/unmap path
nvme-pci: set min_align_mask
swiotlb: respect min_align_mask
swiotlb: don't modify orig_addr in swiotlb_tbl_sync_single
swiotlb: refactor swiotlb_tbl_map_single
swiotlb: clean up swiotlb_tbl_unmap_single
swiotlb: factor out a nr_slots helper
swiotlb: factor out an io_tlb_offset helper
swiotlb: add a IO_TLB_SIZE define
driver core: add a min_align_mask field to struct device_dma_parameters
sdhci: stop poking into swiotlb internals
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
"Besides the usual fixes and new drivers, we are changing CLASS_FLASH
to return success to make it easier to work with V4L2 stuff disabled,
and we are getting rid of enum that should have been plain integer
long time ago. I'm slightly nervous about potential warnings, but it
needed to be fixed at some point"
* tag 'leds-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: lp50xx: Get rid of redundant explicit casting
leds: lp50xx: Update headers block to reflect reality
leds: lp50xx: Get rid of redundant check in lp50xx_enable_disable()
leds: lp50xx: Reduce level of dereferences
leds: lp50xx: Switch to new style i2c-driver probe function
leds: lp50xx: Don't spam logs when probe is deferred
leds: apu: extend support for PC Engines APU1 with newer firmware
leds: flash: Fix multicolor no-ops registration by return 0
leds: flash: Add flash registration with undefined CONFIG_LEDS_CLASS_FLASH
leds: lgm: Add LED controller driver for LGM SoC
dt-bindings: leds: Add bindings for Intel LGM SoC
leds: led-core: Get rid of enum led_brightness
leds: gpio: Set max brightness to 1
leds: lm3533: Switch to using the new API kobj_to_dev()
leds: ss4200: simplify the return expression of register_nasgpio_led()
leds: Use DEVICE_ATTR_{RW, RO, WO} macros
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux
Pull pcmcia update from Dominik Brodowski:
"Improve the use of the kobj API in the core of the Linux PCMCIA
subsystem"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: Switch to using the new API kobj_to_dev()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.12
First set of fixes for v5.12. One iwlwifi kernel crash fix and smaller
fixes to multiple drivers.
ath9k
* fix Spatial Multiplexing Power Save (SMPS) handling to improve thoughtput
mt76
* error handling fixes
* memory leax fixes
iwlwifi
* don't crash during debug collection on DVM devices
MAINTAINERS
* email address update
ath11k
* fix GCC warning about DMA address debug messages
* fix regression which broke QCA6390 AP mode
* tag 'wireless-drivers-2021-02-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
mt76: mt7915: fix unused 'mode' variable
mt76: dma: do not report truncated frames to mac80211
mt76: mt7921: remove incorrect error handling
iwlwifi: pcie: fix iwl_so_trans_cfg link error when CONFIG_IWLMVM is disabled
ath11k: fix AP mode for QCA6390
ath11k: qmi: use %pad to format dma_addr_t
MAINTAINERS: update for mwifiex driver maintainers
iwlwifi: avoid crash on unsupported debug collection
mt76: mt7915: only modify tx buffer list after allocating tx token id
mt76: fix tx skb error handling in mt76_dma_tx_queue_skb
ath9k: fix transmitting to stations in dynamic SMPS mode
====================
Link: https://lore.kernel.org/r/20210226164411.CDD03C433CA@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We should advertise the reworked fifo/cmd handling and huge pages
support. Also while bumping the version number lets cleanup
the logging, there's no point in logging whether we're atomic
(we always are) or what repo we use (it's always in kernel now).
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210224163034.918430-1-zackr@vmware.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Palmer Dabbelt:
"A handful of new RISC-V related patches for this merge window:
- A check to ensure drivers are properly using uaccess. This isn't
manifesting with any of the drivers I'm currently using, but may
catch errors in new drivers.
- Some preliminary support for the FU740, along with the HiFive
Unleashed it will appear on.
- NUMA support for RISC-V, which involves making the arm64 code
generic.
- Support for kasan on the vmalloc region.
- A handful of new drivers for the Kendryte K210, along with the DT
plumbing required to boot on a handful of K210-based boards.
- Support for allocating ASIDs.
- Preliminary support for kernels larger than 128MiB.
- Various other improvements to our KASAN support, including the
utilization of huge pages when allocating the KASAN regions.
We may have already found a bug with the KASAN_VMALLOC code, but it's
passing my tests. There's a fix in the works, but that will probably
miss the merge window.
* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
riscv: Improve kasan population by using hugepages when possible
riscv: Improve kasan population function
riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
riscv: Improve kasan definitions
riscv: Get rid of MAX_EARLY_MAPPING_SIZE
soc: canaan: Sort the Makefile alphabetically
riscv: Disable KSAN_SANITIZE for vDSO
riscv: Remove unnecessary declaration
riscv: Add Canaan Kendryte K210 SD card defconfig
riscv: Update Canaan Kendryte K210 defconfig
riscv: Add Kendryte KD233 board device tree
riscv: Add SiPeed MAIXDUINO board device tree
riscv: Add SiPeed MAIX GO board device tree
riscv: Add SiPeed MAIX DOCK board device tree
riscv: Add SiPeed MAIX BiT board device tree
riscv: Update Canaan Kendryte K210 device tree
dt-bindings: add resets property to dw-apb-timer
dt-bindings: fix sifive gpio properties
dt-bindings: update sifive uart compatible string
dt-bindings: update sifive clint compatible string
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- A small series for Xen event channels adding some sysfs nodes for per
pv-device settings and statistics, and two fixes of theoretical
problems.
- two minor fixes (one for an unlikely error path, one for a comment).
* tag 'for-linus-5.12b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen-front-pgdir-shbuf: don't record wrong grant handle upon error
xen: Replace lkml.org links with lore
xen/evtchn: use READ/WRITE_ONCE() for accessing ring indices
xen/evtchn: use smp barriers for user event ring
xen/events: add per-xenbus device event statistics and settings
|
|
Merge more updates from Andrew Morton:
"118 patches:
- The rest of MM.
Includes kfence - another runtime memory validator. Not as thorough
as KASAN, but it has unmeasurable overhead and is intended to be
usable in production builds.
- Everything else
Subsystems affected by this patch series: alpha, procfs, sysctl,
misc, core-kernel, MAINTAINERS, lib, bitops, checkpatch, init,
coredump, seq_file, gdb, ubsan, initramfs, and mm (thp, cma,
vmstat, memory-hotplug, mlock, rmap, zswap, zsmalloc, cleanups,
kfence, kasan2, and pagemap2)"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
MIPS: make userspace mapping young by default
initramfs: panic with memory information
ubsan: remove overflow checks
kgdb: fix to kill breakpoints on initmem after boot
scripts/gdb: fix list_for_each
x86: fix seq_file iteration for pat/memtype.c
seq_file: document how per-entry resources are managed.
fs/coredump: use kmap_local_page()
init/Kconfig: fix a typo in CC_VERSION_TEXT help text
init: clean up early_param_on_off() macro
init/version.c: remove Version_<LINUX_VERSION_CODE> symbol
checkpatch: do not apply "initialise globals to 0" check to BPF progs
checkpatch: don't warn about colon termination in linker scripts
checkpatch: add kmalloc_array_node to unnecessary OOM message check
checkpatch: add warning for avoiding .L prefix symbols in assembly files
checkpatch: improve TYPECAST_INT_CONSTANT test message
checkpatch: prefer ftrace over function entry/exit printks
checkpatch: trivial style fixes
checkpatch: ignore warning designated initializers using NR_CPUS
checkpatch: improve blank line after declaration test
...
|
