| Age | Commit message (Collapse) | Author |
|---|
|
Update cache info reporting in sysfs to report the correct
number of CUs and associated cache information based on
different spatial partitioning modes.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently, we store CU info only for a single XCC assuming
that it is the same for all XCCs. However, that may not be
true. As a result, store CU info for all XCCs. This info is
later used for CU masking.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the following unaligned 64-bit doorbell
warning seen when submitting packets on HIQ on GFX v9.4.3
by making the HIQ doorbell 64-bit aligned.
The warning is seen when GPU is loaded in any mode other
than SPX mode.
[ +0.000301] ------------[ cut here ]------------
[ +0.000003] Unaligned 64-bit doorbell
[ +0.000030] WARNING: /amdkfd/kfd_doorbell.c:339 write_kernel_doorbell64+0x72/0x80
[ +0.000003] RIP: 0010:write_kernel_doorbell64+0x72/0x80
[ +0.000004] RSP: 0018:ffffc90004287730 EFLAGS: 00010246
[ +0.000005] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ +0.000003] RDX: 0000000000000001 RSI: ffffffff82837c71 RDI: 00000000ffffffff
[ +0.000003] RBP: ffffc90004287748 R08: 0000000000000003 R09: 0000000000000001
[ +0.000002] R10: 000000000000001a R11: ffff88a034008198 R12: ffffc900013bd004
[ +0.000003] R13: 0000000000000008 R14: ffffc900042877b0 R15: 000000000000007f
[ +0.000003] FS: 00007fa8c7b62000(0000) GS:ffff889f88400000(0000) knlGS:0000000000000000
[ +0.000004] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000003] CR2: 000056111c45aaf0 CR3: 00000001414f2002 CR4: 0000000000770ee0
[ +0.000003] PKRU: 55555554
[ +0.000002] Call Trace:
[ +0.000004] <TASK>
[ +0.000006] kq_submit_packet+0x45/0x50 [amdgpu]
[ +0.000524] pm_send_set_resources+0x7f/0xc0 [amdgpu]
[ +0.000500] set_sched_resources+0xe4/0x160 [amdgpu]
[ +0.000503] start_cpsch+0x1c5/0x2a0 [amdgpu]
[ +0.000497] kgd2kfd_device_init.cold+0x816/0xb42 [amdgpu]
[ +0.000743] amdgpu_amdkfd_device_init+0x15f/0x1f0 [amdgpu]
[ +0.000602] amdgpu_device_init.cold+0x1813/0x2176 [amdgpu]
[ +0.000684] ? pci_bus_read_config_word+0x4a/0x80
[ +0.000012] ? do_pci_enable_device+0xdc/0x110
[ +0.000008] amdgpu_driver_load_kms+0x1a/0x110 [amdgpu]
[ +0.000545] amdgpu_pci_probe+0x197/0x400 [amdgpu]
Fixes: c31866651086 ("drm/amdgpu: use doorbell mgr for kfd kernel doorbells")
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the case where the code currently passes
absolute register address and not the reg offset, which HWS
expects, when sending the PM4 packet to set/update CWSR grace
period. Additionally, cleanup the signature of
build_grace_period_packet_info function as it no longer needs
the inst parameter.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a compile error when this commit is added:
md: raid1: fix potential OOB in raid1_remove_disk()
drivers/md/raid1.c: In function 'raid1_remove_disk':
drivers/md/raid1.c:1844:9: error: ISO C90 forbids mixed declarations
and code [-Werror=declaration-after-statement]
1844 | struct raid1_info *p = conf->mirrors + number;
| ^~~~~~
That's because the new code was inserted before the struct.
The change is move the struct command above this commit.
Fixes: 8b0472b50bcf ("md: raid1: fix potential OOB in raid1_remove_disk()")
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/46d929d0-2aab-4cf2-b2bf-338963e8ba5a@redhat.com
|
|
Add 'const' to the definition of the 'trip' argument of the
.get_trend() thermal zone callback to indicate that the trip point
passed to it should not be modified by it and adjust the
callback functions implementing it, thermal_get_trend() in the
ACPI thermal driver and __ti_thermal_get_trend(), accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
|
|
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* nouveau: Lockdep workaround
* fbdev/g364fb: Build fix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230911141915.GA983@linux-uq9g
|
|
Making sure the UCSI debugfs entry actually exists before
attempting to remove it.
Fixes: df0383ffad64 ("usb: typec: ucsi: Add debugfs for ucsi commands")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Closes: https://lore.kernel.org/linux-usb/700df3c4-2f6c-85f9-6c61-065bc5b2db3a@intel.com/
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Link: https://lore.kernel.org/r/20230906084842.1922052-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add quirk for ASUS ROG X16 (GV601V, 2023 versions) Flow 2-in-1
to enable tablet mode with lid flip (all screen rotations).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230905082813.13470-1-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The only probing method supported by the Nvidia SN2201 platform driver
is probing through an ACPI match table. Hence add a dependency on
ACPI, to prevent asking the user about this driver when configuring a
kernel without ACPI support.
Fixes: 662f24826f95 ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ec5a4071691ab08d58771b7732a9988e89779268.1693828363.git.geert+renesas@glider.be
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The latest version of the mlxbf_bootctl driver utilizes
"sysfs_format_mac", and this API is only available if
NET is defined in the kernel configuration. This patch
changes the mlxbf_bootctl Kconfig to depend on NET.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309031058.JvwNDBKt-lkp@intel.com/
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20230905133243.31550-1-davthompson@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This fix involves 2 changes:
- All event regs have a reset value of 0, which is not a valid
event_number as per the event_list for most blocks and hence seen
as an error. Add a "disable" event with event_number 0 for all blocks.
- The enable bit for each counter need not be checked before
reading the event info, and hence removed.
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/04d0213932d32681de1c716b54320ed894e52425.1693917738.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Replace sprintf with sysfs_emit where possible.
Size check in mlxbf_pmc_event_list_show should account for "\0".
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/bef39ef32319a31b32f999065911f61b0d3b17c3.1693917738.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This commit drops over-sized network packets to avoid tmfifo
queue stuck.
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/9318936c2447f76db475c985ca6d91f057efcd41.1693322547.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This commit fixes tmfifo console stuck issue when the virtual
networking interface is in down state. In such case, the network
Rx descriptors runs out and causes the Rx network packet staying
in the head of the tmfifo thus blocking the console packets. The
fix is to drop the Rx network packet when no more Rx descriptors.
Function name mlxbf_tmfifo_release_pending_pkt() is also renamed
to mlxbf_tmfifo_release_pkt() to be more approperiate.
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/8c0177dc938ae03f52ff7e0b62dbeee74b7bec09.1693322547.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
MT7988 SoC support 3 NICs. Fix pse_port configuration in
mtk_flow_set_output_device routine if the traffic is offloaded to eth2.
Rely on mtk_pse_port definitions.
Fixes: 88efedf517e6 ("net: ethernet: mtk_eth_soc: enable nft hw flowtable_offload for MT7988 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable dma_addr in function mtk_poll_rx can be uninitialized on
some of the error paths. In practise this doesn't matter, even random
data present in uninitialized stack memory can safely be used in the
way it happens in the error path.
However, in order to make Smatch happy make sure the variable is
always initialized.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e4454 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
entry
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df88 ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab9f ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_dynamic_config_poll_valid()
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a new fdb entry is added (with both ports of the
ADIN2111 bridged), the driver configures the MAC filters for the wrong
port, which results in the forwarding being done by the host, and not
actually hardware offloaded.
The ADIN2111 offloads the forwarding by setting filters on the
destination MAC address of incoming frames. Based on these, they may be
routed to the other port. Thus, if a frame has to be forwarded from port
1 to port 2, the required configuration for the ADDR_FILT_UPRn register
should set the APPLY2PORT1 bit (instead of APPLY2PORT2, as it's
currently the case).
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mtk_hwlro_get_fdir_all()
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rules is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rules to avoid OOB writing or NULL pointer dereference.
Fixes: 90b509b39ac9 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid OOB writing or NULL pointer dereference.
Fixes: c5d511c49587 ("net: bcmasp: Add support for wake on net filters")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce33317023 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kyril reports that crashkernels fail to work on confidential VMs that
rely on the unaccepted memory table, and this appears to be caused by
the fact that it is not considered part of the set of firmware tables
that the crashkernel needs to map.
This is an oversight, and a result of the use of the EFI_LOADER_DATA
memory type for this table. The correct memory type to use for any
firmware table is EFI_ACPI_RECLAIM_MEMORY (including ones created by the
EFI stub), even though the name suggests that is it specific to ACPI.
ACPI reclaim means that the memory is used by the firmware to expose
information to the operating system, but that the memory region has no
special significance to the firmware itself, and the OS is free to
reclaim the memory and use it as ordinary memory if it is not interested
in the contents, or if it has already consumed them. In Linux, this
memory is never reclaimed, but it is always covered by the kernel direct
map and generally made accessible as ordinary memory.
On x86, ACPI reclaim memory is translated into E820_ACPI, which the
kexec logic already recognizes as memory that the crashkernel may need
to to access, and so it will be mapped and accessible to the booting
crash kernel.
Fixes: 745e3ed85f71 ("efi/libstub: Implement support for unaccepted memory")
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
snprintf() returns the "number of characters which *would* be generated for
the given input", not the size *really* generated.
In order to avoid too large values for 'o' (and potential negative values
for "sizeof(linebuf) o") use scnprintf() instead of snprintf().
Note that given the "w < 4" in the for loop, the buffer can NOT
overflow, but using the *right* function is always better.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a6e ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Pull drm ci scripts from Dave Airlie:
"This is a bunch of ci integration for the freedesktop gitlab instance
where we currently do upstream userspace testing on diverse sets of
GPU hardware. From my perspective I think it's an experiment worth
going with and seeing how the benefits/noise playout keeping these
files useful.
Ideally I'd like to get this so we can do pre-merge testing on PRs
eventually.
Below is some info from danvet on why we've ended up making the
decision and how we can roll it back if we decide it was a bad plan.
Why in upstream?
- like documentation, testcases, tools CI integration is one of these
things where you can waste endless amounts of time if you
accidentally have a version that doesn't match your source code
- but also like the above, there's a balance, this is the initial cut
of what we think makes sense to keep in sync vs out-of-tree,
probably needs adjustment
- gitlab supports out-of-repo gitlab integration and that's what's
been used for the kernel in drm, but it results in per-driver
fragmentation and lots of duplicated effort. the simple act of
smashing an arbitrary winner into a topic branch already started
surfacing patches on dri-devel and sparking good cross driver team
discussions
Why gitlab?
- it's not any more shit than any of the other CI
- drm userspace uses it extensively for everything in userspace, we
have a lot of people and experience with this, including
integration of hw testing labs
- media userspace like gstreamer is also on gitlab.fd.o, and there's
discussion to extend this to the media subsystem in some fashion
Can this be shared?
- there's definitely a pile of code that could move to scripts/ if
other subsystem adopt ci integration in upstream kernel git. other
bits are more drm/gpu specific like the igt-gpu-tests/tools
integration
- docker images can be run locally or in other CI runners
Will we regret this?
- it's all in one directory, intentionally, for easy deletion
- probably 1-2 years in upstream to see whether this is worth it or a
Big Mistake. that's roughly what it took to _really_ roll out solid
CI in the bigger userspace projects we have on gitlab.fd.o like
mesa3d"
* tag 'topic/drm-ci-2023-08-31-1' of git://anongit.freedesktop.org/drm/drm:
drm: ci: docs: fix build warning - add missing escape
drm: Add initial ci/ subdirectory
|
|
The access to page pool `cache' array and the `count' variable
is not locked. Page pool cache access is fine as long as there
is only one consumer per pool.
octeontx2 driver fills in rx buffers from page pool in NAPI context.
If system is stressed and could not allocate buffers, refiiling work
will be delegated to a delayed workqueue. This means that there are
two cosumers to the page pool cache.
Either workqueue or IRQ/NAPI can be run on other CPU. This will lead
to lock less access, hence corruption of cache pool indexes.
To fix this issue, NAPI is rescheduled from workqueue context to refill
rx buffers.
Fixes: b2e3406a38f0 ("octeontx2-pf: Add support for page pool")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inject fault When select CONFIG_VCAP_KUNIT_TEST, the below memory leak
occurs. If kzalloc() for duprule succeeds, but the following
kmemdup() fails, the duprule, ckf and caf memory will be leaked. So kfree
them in the error path.
unreferenced object 0xffff122744c50600 (size 192):
comm "kunit_try_catch", pid 346, jiffies 4294896122 (age 911.812s)
hex dump (first 32 bytes):
10 27 00 00 04 00 00 00 1e 00 00 00 2c 01 00 00 .'..........,...
00 00 00 00 00 00 00 00 18 06 c5 44 27 12 ff ff ...........D'...
backtrace:
[<00000000394b0db8>] __kmem_cache_alloc_node+0x274/0x2f8
[<0000000001bedc67>] kmalloc_trace+0x38/0x88
[<00000000b0612f98>] vcap_dup_rule+0x50/0x460
[<000000005d2d3aca>] vcap_add_rule+0x8cc/0x1038
[<00000000eef9d0f8>] test_vcap_xn_rule_creator.constprop.0.isra.0+0x238/0x494
[<00000000cbda607b>] vcap_api_rule_remove_in_front_test+0x1ac/0x698
[<00000000c8766299>] kunit_try_run_case+0xe0/0x20c
[<00000000c4fe9186>] kunit_generic_run_threadfn_adapter+0x50/0x94
[<00000000f6864acf>] kthread+0x2e8/0x374
[<0000000022e639b3>] ret_from_fork+0x10/0x20
Fixes: 814e7693207f ("net: microchip: vcap api: Add a storage state to a VCAP rule")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_available_child_of_node performs an of_node_get
on each iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- The kernel now dynamically probes for misaligned access speed, as
opposed to relying on a table of known implementations.
- Support for non-coherent devices on systems using the Andes AX45MP
core, including the RZ/Five SoCs.
- Support for the V extension in ptrace(), again.
- Support for KASLR.
- Support for the BPF prog pack allocator in RISC-V.
- A handful of bug fixes and cleanups.
* tag 'riscv-for-linus-6.6-mw2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (25 commits)
soc: renesas: Kconfig: For ARCH_R9A07G043 select the required configs if dependencies are met
riscv: Kconfig.errata: Add dependency for RISCV_SBI in ERRATA_ANDES config
riscv: Kconfig.errata: Drop dependency for MMU in ERRATA_ANDES_CMO config
riscv: Kconfig: Select DMA_DIRECT_REMAP only if MMU is enabled
bpf, riscv: use prog pack allocator in the BPF JIT
riscv: implement a memset like function for text
riscv: extend patch_text_nosync() for multiple pages
bpf: make bpf_prog_pack allocator portable
riscv: libstub: Implement KASLR by using generic functions
libstub: Fix compilation warning for rv32
arm64: libstub: Move KASLR handling functions to kaslr.c
riscv: Dump out kernel offset information on panic
riscv: Introduce virtual kernel mapping KASLR
RISC-V: Add ptrace support for vectors
soc: renesas: Kconfig: Select the required configs for RZ/Five SoC
cache: Add L2 cache management for Andes AX45MP RISC-V core
dt-bindings: cache: andestech,ax45mp-cache: Add DT binding documentation for L2 cache controller
riscv: mm: dma-noncoherent: nonstandard cache operations support
riscv: errata: Add Andes alternative ports
riscv: asm: vendorid_list: Add Andes Technology to the vendors list
...
|
|
Pull more SCSI updates from James Bottomley:
"Mostly small stragglers that missed the initial merge.
Driver updates are qla2xxx and smartpqi (mp3sas has a high diffstat
due to the volatile qualifier removal, fnic due to unused function
removal and sd.c has a lot of code shuffling to remove forward
declarations)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: ufs: core: No need to update UPIU.header.flags and lun in advanced RPMB handler
scsi: ufs: core: Add advanced RPMB support where UFSHCI 4.0 does not support EHS length in UTRD
scsi: mpt3sas: Remove volatile qualifier
scsi: mpt3sas: Perform additional retries if doorbell read returns 0
scsi: libsas: Simplify sas_queue_reset() and remove unused code
scsi: ufs: Fix the build for the old ARM OABI
scsi: qla2xxx: Fix unused variable warning in qla2xxx_process_purls_pkt()
scsi: fnic: Remove unused functions fnic_scsi_host_start/end_tag()
scsi: qla2xxx: Fix spelling mistake "tranport" -> "transport"
scsi: fnic: Replace sgreset tag with max_tag_id
scsi: qla2xxx: Remove unused variables in qla24xx_build_scsi_type_6_iocbs()
scsi: qla2xxx: Fix nvme_fc_rcv_ls_req() undefined error
scsi: smartpqi: Change driver version to 2.1.24-046
scsi: smartpqi: Enhance error messages
scsi: smartpqi: Enhance controller offline notification
scsi: smartpqi: Enhance shutdown notification
scsi: smartpqi: Simplify lun_number assignment
scsi: smartpqi: Rename pciinfo to pci_info
scsi: smartpqi: Rename MACRO to clarify purpose
scsi: smartpqi: Add abort handler
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver symbol lookup fix from Greg KH:
"Here is one last fixup for your tree for 6.6-rc1. It resolves a
problem with the way that symbol_get was changed in the module tree
merge in your tree to fix up the DVB drivers which rely on this old
api to attach new devices.
As the changelog comment says:
In commit 9011e49d54dc ("modules: only allow symbol_get of
EXPORT_SYMBOL_GPL modules") the use of symbol_get is properly
restricted to GPL-only marked symbols. This interacts oddly with the
DVB logic which only uses dvb_attach() to load the dvb driver which
then uses symbol_get().
Fix this up by properly marking all of the dvb_attach attach symbols
as EXPORT_SYMBOL_GPL().
This has been acked by Hans from the V4L driver side, Luis from the
module side, Mauro on the media side, and Christoph said it was the
correct solution, and was tested by the original reporter of the
issue.
It has passed 0-day testing, but has not been in linux-next due to it
only being sent yesterday"
* tag 'driver-core-6.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
media: dvb: symbol fixup for dvb_attach()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- Add PCI_DYNAMIC_OF_NODES dependency on OF_IRQ to fix sparc64 build
error (Lizhi Hou)
- After coalescing host bridge resources, free any released resources
to avoid a leak (Ross Lagerwall)
- Revert a quirk that prevented NVIDIA T4 GPUs from using Secondary Bus
Reset. The quirk worked around an issue that we now think is related
to the Root Port, not the GPU (Bjorn Helgaas)
* tag 'pci-v6.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
Revert "PCI: Mark NVIDIA T4 GPUs to avoid bus reset"
PCI: Free released resource after coalescing
PCI: Fix CONFIG_PCI_DYNAMIC_OF_NODES kconfig dependencies
|
|
Pull NTB updates from Jon Mason:
"Link toggling fixes and debugfs error path fixes"
[ And for everybody like me who always have to remind themselves what
the TLA of the day is, and what NTB stands for - it's a PCIe
"Non-Transparent Bridge" thing - Linus ]
* tag 'ntb-6.6' of https://github.com/jonmason/ntb:
ntb: Check tx descriptors outstanding instead of head/tail for tx queue
ntb: Fix calculation ntb_transport_tx_free_entry()
ntb: Drop packets when qp link is down
ntb: Clean up tx tail index on link down
ntb: amd: Drop unnecessary error check for debugfs_create_dir
NTB: ntb_tool: Switch to memdup_user_nul() helper
dtivers: ntb: fix parameter check in perf_setup_dbgfs()
ntb: Remove error checking for debugfs_create_dir()
|
|
In commit 9011e49d54dc ("modules: only allow symbol_get of
EXPORT_SYMBOL_GPL modules") the use of symbol_get is properly restricted
to GPL-only marked symbols. This interacts oddly with the DVB logic
which only uses dvb_attach() to load the dvb driver which then uses
symbol_get().
Fix this up by properly marking all of the dvb_attach attach symbols as
EXPORT_SYMBOL_GPL().
Fixes: 9011e49d54dc ("modules: only allow symbol_get of EXPORT_SYMBOL_GPL modules")
Cc: stable <stable@kernel.org>
Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-media@vger.kernel.org
Cc: linux-modules@vger.kernel.org
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/20230908092035.3815268-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull block fixes from Jens Axboe:
- Fix null_blk polled IO timeout handling (Chengming)
- Regression fix for swapped arguments in drbd bvec_set_page()
(Christoph)
- String length handling fix for s390 dasd (Heiko)
- Fixes for blk-throttle accounting (Yu)
- Fix page pinning issue for same page segments (Christoph)
- Remove redundant file_remove_privs() call (Christoph)
- Fix a regression in partition handling for devices not supporting
partitions (Li)
* tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux:
drbd: swap bvec_set_page len and offset
block: fix pin count management when merging same-page segments
null_blk: fix poll request timeout handling
s390/dasd: fix string length handling
block: don't add or resize partition on the disk with GENHD_FL_NO_PART
block: remove the call to file_remove_privs in blkdev_write_iter
blk-throttle: consider 'carryover_ios/bytes' in throtl_trim_slice()
blk-throttle: use calculate_io/bytes_allowed() for throtl_trim_slice()
blk-throttle: fix wrong comparation while 'carryover_ios/bytes' is negative
blk-throttle: print signed value 'carryover_bytes/ios' for user
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"Eliminate an obsolete thermal zone registration function"
* tag 'thermal-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Drop thermal_zone_device_register()
thermal: Use thermal_tripless_zone_device_register()
thermal: core: Add function for registering tripless thermal zones
thermal: core: Clean up headers of thermal zone registration functions
|
|
Commit a1d767191096 ("md: use mddev->external to select holder in
export_rdev()") fix the problem that 'claim_rdev' is used for
blkdev_get_by_dev() while 'rdev' is used for blkdev_put().
However, if mddev->external is changed from 0 to 1, then 'rdev' is used
for blkdev_get_by_dev() while 'claim_rdev' is used for blkdev_put(). And
this problem can be reporduced reliably by following:
New file: mdadm/tests/23rdev-lifetime
devname=${dev0##*/}
devt=`cat /sys/block/$devname/dev`
pid=""
runtime=2
clean_up_test() {
pill -9 $pid
echo clear > /sys/block/md0/md/array_state
}
trap 'clean_up_test' EXIT
add_by_sysfs() {
while true; do
echo $devt > /sys/block/md0/md/new_dev
done
}
remove_by_sysfs(){
while true; do
echo remove > /sys/block/md0/md/dev-${devname}/state
done
}
echo md0 > /sys/module/md_mod/parameters/new_array || die "create md0 failed"
add_by_sysfs &
pid="$pid $!"
remove_by_sysfs &
pid="$pid $!"
sleep $runtime
exit 0
Test cmd:
./test --save-logs --logdir=/tmp/ --keep-going --dev=loop --tests=23rdev-lifetime
Test result:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 960 at block/bdev.c:618 blkdev_put+0x27c/0x330
Modules linked in: multipath md_mod loop
CPU: 0 PID: 960 Comm: test Not tainted 6.5.0-rc2-00121-g01e55c376936-dirty #50
RIP: 0010:blkdev_put+0x27c/0x330
Call Trace:
<TASK>
export_rdev.isra.23+0x50/0xa0 [md_mod]
mddev_unlock+0x19d/0x300 [md_mod]
rdev_attr_store+0xec/0x190 [md_mod]
sysfs_kf_write+0x52/0x70
kernfs_fop_write_iter+0x19a/0x2a0
vfs_write+0x3b5/0x770
ksys_write+0x74/0x150
__x64_sys_write+0x22/0x30
do_syscall_64+0x40/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fix the problem by recording if 'rdev' is used as holder.
Fixes: a1d767191096 ("md: use mddev->external to select holder in export_rdev()")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230825025532.1523008-3-yukuai1@huaweicloud.com
|
|
Except for initial reference, mddev->kobject is referenced by
rdev->kobject, and if the last rdev is freed, there is no guarantee that
mddev is still valid. Hence mddev should not be used anymore after
export_rdev().
This problem can be triggered by following test for mdadm at very
low rate:
New file: mdadm/tests/23rdev-lifetime
devname=${dev0##*/}
devt=`cat /sys/block/$devname/dev`
pid=""
runtime=2
clean_up_test() {
pill -9 $pid
echo clear > /sys/block/md0/md/array_state
}
trap 'clean_up_test' EXIT
add_by_sysfs() {
while true; do
echo $devt > /sys/block/md0/md/new_dev
done
}
remove_by_sysfs(){
while true; do
echo remove > /sys/block/md0/md/dev-${devname}/state
done
}
echo md0 > /sys/module/md_mod/parameters/new_array || die "create md0 failed"
add_by_sysfs &
pid="$pid $!"
remove_by_sysfs &
pid="$pid $!"
sleep $runtime
exit 0
Test cmd:
./test --save-logs --logdir=/tmp/ --keep-going --dev=loop --tests=23rdev-lifetime
Test result:
general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6bcb: 0000 [#4] PREEMPT SMP
CPU: 0 PID: 1292 Comm: test Tainted: G D W 6.5.0-rc2-00121-g01e55c376936 #562
RIP: 0010:md_wakeup_thread+0x9e/0x320 [md_mod]
Call Trace:
<TASK>
mddev_unlock+0x1b6/0x310 [md_mod]
rdev_attr_store+0xec/0x190 [md_mod]
sysfs_kf_write+0x52/0x70
kernfs_fop_write_iter+0x19a/0x2a0
vfs_write+0x3b5/0x770
ksys_write+0x74/0x150
__x64_sys_write+0x22/0x30
do_syscall_64+0x40/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Fix this problem by don't dereference mddev after export_rdev().
Fixes: 3ce94ce5d05a ("md: fix duplicate filename for rdev")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230825025532.1523008-2-yukuai1@huaweicloud.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix an Intel RAPL power capping driver regression introduced during
the 6.5 development cycle (Srinivas Pandruvada)"
* tag 'pm-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap: intel_rapl: Fix invalid setting of Power Limit 4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fix from Bartosz Golaszewski:
- fix a regression in irqchip setup in gpio-zynq
* tag 'gpio-fixes-for-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: zynq: restore zynq_gpio_irq_reqres/zynq_gpio_irq_relres callbacks
|
|
This reverts commit d5af729dc2071273f14cbb94abbc60608142fd83.
d5af729dc207 ("PCI: Mark NVIDIA T4 GPUs to avoid bus reset") avoided
Secondary Bus Reset on the T4 because the reset seemed to not work when the
T4 was directly attached to a Root Port.
But NVIDIA thinks the issue is probably related to some issue with the Root
Port, not with the T4. The T4 provides neither PM nor FLR reset, so
masking bus reset compromises this device for assignment scenarios.
Revert d5af729dc207 as requested by Wu Zongyong. This will leave SBR
broken in the specific configuration Wu tested, as it was in v6.5, so Wu
will debug that further.
Link: https://lore.kernel.org/r/ZPqMCDWvITlOLHgJ@wuzongyong-alibaba
Link: https://lore.kernel.org/r/20230908201104.GA305023@bhelgaas
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"The main one is a fix for a broken strscpy() conversion that landed in
the merge window and broke early parsing of the kernel command line.
- Fix an incorrect mask in the CXL PMU driver
- Fix a regression in early parsing of the kernel command line
- Fix an IP checksum OoB access reported by syzbot"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: csum: Fix OoB access in IP checksum code for negative lengths
arm64/sysreg: Fix broken strncpy() -> strscpy() conversion
perf: CXL: fix mismatched number of counters mask
|
