| Age | Commit message (Collapse) | Author |
|---|
|
Currently all controller IP/revisions except DWC3_usb3 >= 310a
wait 1ms unconditionally for ENDXFER completion when IOC is not
set. This is because DWC_usb3 controller revisions >= 3.10a
supports GUCTL2[14: Rst_actbitlater] bit which allows polling
CMDACT bit to know whether ENDXFER command is completed.
Consider a case where an IN request was queued, and parallelly
soft_disconnect was called (due to ffs_epfile_release). This
eventually calls stop_active_transfer with IOC cleared, hence
send_gadget_ep_cmd() skips waiting for CMDACT cleared during
EndXfer. For DWC3 controllers with revisions >= 310a, we don't
forcefully wait for 1ms either, and we proceed by unmapping the
requests. If ENDXFER didn't complete by this time, it leads to
SMMU faults since the controller would still be accessing those
requests.
Fix this by ensuring ENDXFER completion by adding 1ms delay in
__dwc3_stop_active_transfer() unconditionally.
Cc: stable@vger.kernel.org
Fixes: b353eb6dc285 ("usb: dwc3: gadget: Skip waiting for CMDACT cleared during endxfer")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20240502044103.1066350-1-quic_prashk@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.10 merge window
This includes following USB4/Thunderbolt changes for the v6.10 merge
window:
- Enable NVM firmare upgrade on Intel Maple Ridge Thunderbolt 4
controller
- Improve USB3 tunnel bandwidth calculation
- Improve sideband access
- Minor cleanups and fixes.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Correct trace output of firmware connection manager packets
thunderbolt: Fix kernel-doc for tb_tunnel_alloc_dp()
thunderbolt: Fix uninitialized variable in tb_tunnel_alloc_usb3()
thunderbolt: There are only 5 basic router registers in pre-USB4 routers
thunderbolt: No need to loop over all retimers if access fails
thunderbolt: Increase sideband access polling delay
thunderbolt: Get rid of TB_CFG_PKG_PREPARE_TO_SLEEP
thunderbolt: Use correct error code with ERROR_NOT_SUPPORTED
thunderbolt: Allow USB3 bandwidth to be lower than maximum supported
thunderbolt: Fix calculation of consumed USB3 bandwidth on a path
thunderbolt: Enable NVM upgrade support on Intel Maple Ridge
|
|
This reverts commit 9801b5b28c6929139d6fceeee8d739cc67bb2739.
This patch introduced a potential deadlock scenario:
[Wed May 8 10:02:06 2024] Possible unsafe locking scenario:
[Wed May 8 10:02:06 2024] CPU0 CPU1
[Wed May 8 10:02:06 2024] ---- ----
[Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock);
[Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock);
[Wed May 8 10:02:06 2024] lock(vivid_ctrls:1620:(hdl_vid_cap)->_lock);
[Wed May 8 10:02:06 2024] lock(vivid_ctrls:1608:(hdl_user_vid)->_lock);
For now just revert.
Fixes: 9801b5b28c69 ("media: v4l2-ctrls: show all owned controls in log_status")
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Before this commit on probe() the driver would do:
reset=1 // from probe() calling gpiod_get(GPIOD_OUT_HIGH)
reset=0 // from resume()
msleep(20) // from resume()
So if reset was 0 before getting the GPIO the reset line would only be
driven high for a very short time and sometimes there would be errors
reading the id register afterwards.
Add a msleep(20) after getting the reset line to ensure the sensor is
properly reset:
reset=1 // from probe() calling gpiod_get(GPIOD_OUT_HIGH)
msleep(20) // from probe()
reset=0 // from resume()
msleep(20) // from resume()
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Use dev_dbg() for printing messages on user-triggerable conditions that
have no relation to driver or hardware issues.
Fixes: 3c1dfb5a69cf ("media: intel/ipu6: input system video nodes and buffer queues")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Set up sysfs for the Atmel SHA204a. Provide the content of the otp zone as
an attribute field on the sysfs entry. Thereby make sure that if the chip
is locked, not connected or trouble with the i2c bus, the sysfs device is
not set up. This is mostly already handled in atmel-i2c.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Provide a read function reading the otp zone. The otp zone can be used for
storing serial numbers. The otp zone, as also data zone, are only
accessible if the chip was locked before. Locking the chip is a post
production customization and has to be done manually i.e. not by this
driver. Without this step the chip is pretty much not usable, where
putting or not putting data into the otp zone is optional.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Make the memory read function name more specific to the read memory zone.
The Atmel SHA204 chips provide config, otp and data zone. The implemented
read function in fact only reads some fields in zone config. The function
renaming allows for a uniform naming scheme when reading from other memory
zones.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Add missing description for argument hwrng.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixes the following two Coccinelle/coccicheck warnings reported by
memdup.cocci:
iaa_crypto_main.c:350:19-26: WARNING opportunity for kmemdup
iaa_crypto_main.c:358:18-25: WARNING opportunity for kmemdup
Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com>
Reviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
iMX8ULP have a secure-enclave hardware IP called EdgeLock Enclave(ELE),
that control access to caam controller's register page, i.e., page0.
At all, if the ELE release access to CAAM controller's register page,
it will release to secure-world only.
Clocks are turned on automatically for iMX8ULP. There exists the caam
clock gating bit, but it is not advised to gate the clock at linux, as
optee-os or any other entity might be using it.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
CAAM clock initializat is done based on the basis of soc specific
info stored in struct caam_imx_data:
- caam-page0-access flag
- num_clks
CAAM driver needs to be aware of access rights to CAAM control page
i.e., page0, to do things differently.
Signed-off-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Dma address mapping fails on unaligned scatterlist offset. Use sw
fallback for these cases.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
RSA text data uses variable length buffer allocated in software stack.
Calling kfree on it causes undefined behaviour in subsequent operations.
Cc: <stable@vger.kernel.org> #6.7+
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Skip sw fallback allocation if RSA module failed to get device handle.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Skip dma setup and mapping for AES driver if plaintext is empty.
Signed-off-by: Jia Jie Ho <jiajie.ho@starfivetech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This isn't modified at runtime. Mark it const so it can move to
read-only data.
Cc: dann frazier <dann.frazier@canonical.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240502233447.420888-1-swboyd@chromium.org
|
|
In "struct dmtimer", the 'rate' field is unused.
Remove it.
Found with cppcheck, unusedStructMember.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/c9f7579922c587fce334a1aa9651f3189de7a00b.1714513336.git.christophe.jaillet@wanadoo.fr
|
|
The Renesas OS Timer (OSTM) driver contains two probe points, of which
only one should complete:
1. Early probe, using TIMER_OF_DECLARE(), to provide the sole
clocksource on (arm32) RZ/A1 and RZ/A2 SoCs,
2. Normal probe, using a platform driver, to provide additional timers
on (arm64 + riscv) RZ/G2L and similar SoCs.
The latter is needed because using OSTM on RZ/G2L requires manipulation
of its reset signal, which is not yet available at the time of early
probe, causing early probe to fail with -EPROBE_DEFER. It is only
enabled when building a kernel with support for the RZ/G2L family, so it
does not impact RZ/A1 and RZ/A2. Hence only one probe method can
complete on all affected systems.
As relying on the order of initialization of subsystems inside the
kernel is fragile, set the DT node's OF_POPULATED flag after a succesful
early probe. This makes sure the platform driver's probe is never
called after a successful early probe.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviwed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/bd027379713cbaafa21ffe9e848ebb7f475ca0e7.1710930542.git.geert+renesas@glider.be
|
|
The RZ/V2H(P) (R9A09G057) SoC is equipped with the Generic Timer Module,
also known as OSTM. Similar to the RZ/G2L SoC, the OSTM on the RZ/V2H(P)
SoC requires the reset line to be deasserted before accessing any
registers.
Early call to ostm_init() happens through TIMER_OF_DECLARE() which always
fails with -EPROBE_DEFER, as resets are not available that early in the
boot process. To address this issue on the RZ/V2H(P) SoC, enable the OSTM
driver to be reprobed through the platform driver probe mechanism.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20240322151219.885832-3-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
We want the USB fixes in here as well, and resolve a merge conflict in
drivers/usb/dwc3/core.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This was missed because of the function pointer indirection.
nvidia_smmu_context_fault() is also installed as a irq function, and the
'void *' was changed to a struct arm_smmu_domain. Since the iommu_domain
is embedded at a non-zero offset this causes nvidia_smmu_context_fault()
to miscompute the offset. Fixup the types.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000120
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
CM = 0, WnR = 0, TnD = 0, TagAccess = 0
GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=0000000107c9f000
[0000000000000120] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 0000000096000004 [#1] SMP
Modules linked in:
CPU: 1 PID: 47 Comm: kworker/u25:0 Not tainted 6.9.0-0.rc7.58.eln136.aarch64 #1
Hardware name: Unknown NVIDIA Jetson Orin NX/NVIDIA Jetson Orin NX, BIOS 3.1-32827747 03/19/2023
Workqueue: events_unbound deferred_probe_work_func
pstate: 604000c9 (nZCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : nvidia_smmu_context_fault+0x1c/0x158
lr : __free_irq+0x1d4/0x2e8
sp : ffff80008044b6f0
x29: ffff80008044b6f0 x28: ffff000080a60b18 x27: ffffd32b5172e970
x26: 0000000000000000 x25: ffff0000802f5aac x24: ffff0000802f5a30
x23: ffff0000802f5b60 x22: 0000000000000057 x21: 0000000000000000
x20: ffff0000802f5a00 x19: ffff000087d4cd80 x18: ffffffffffffffff
x17: 6234362066666666 x16: 6630303078302d30 x15: ffff00008156d888
x14: 0000000000000000 x13: ffff0000801db910 x12: ffff00008156d6d0
x11: 0000000000000003 x10: ffff0000801db918 x9 : ffffd32b50f94d9c
x8 : 1fffe0001032fda1 x7 : ffff00008197ed00 x6 : 000000000000000f
x5 : 000000000000010e x4 : 000000000000010e x3 : 0000000000000000
x2 : ffffd32b51720cd8 x1 : ffff000087e6f700 x0 : 0000000000000057
Call trace:
nvidia_smmu_context_fault+0x1c/0x158
__free_irq+0x1d4/0x2e8
free_irq+0x3c/0x80
devm_free_irq+0x64/0xa8
arm_smmu_domain_free+0xc4/0x158
iommu_domain_free+0x44/0xa0
iommu_deinit_device+0xd0/0xf8
__iommu_group_remove_device+0xcc/0xe0
iommu_bus_notifier+0x64/0xa8
notifier_call_chain+0x78/0x148
blocking_notifier_call_chain+0x4c/0x90
bus_notify+0x44/0x70
device_del+0x264/0x3e8
pci_remove_bus_device+0x84/0x120
pci_remove_root_bus+0x5c/0xc0
dw_pcie_host_deinit+0x38/0xe0
tegra_pcie_config_rp+0xc0/0x1f0
tegra_pcie_dw_probe+0x34c/0x700
platform_probe+0x70/0xe8
really_probe+0xc8/0x3a0
__driver_probe_device+0x84/0x160
driver_probe_device+0x44/0x130
__device_attach_driver+0xc4/0x170
bus_for_each_drv+0x90/0x100
__device_attach+0xa8/0x1c8
device_initial_probe+0x1c/0x30
bus_probe_device+0xb0/0xc0
deferred_probe_work_func+0xbc/0x120
process_one_work+0x194/0x490
worker_thread+0x284/0x3b0
kthread+0xf4/0x108
ret_from_fork+0x10/0x20
Code: a9b97bfd 910003fd a9025bf5 f85a0035 (b94122a1)
Cc: stable@vger.kernel.org
Fixes: e0976331ad11 ("iommu/arm-smmu: Pass arm_smmu_domain to internal functions")
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com>
Closes: https://lore.kernel.org/all/jto5e3ili4auk6sbzpnojdvhppgwuegir7mpd755anfhwcbkfz@2u5gh7bxb4iv
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
Acked-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/0-v1-24ce064de41f+4ac-nvidia_smmu_fault_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
i2c_device_id::driver_data to 0
The driver doesn't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove the trailing commas after the sentinel entry.
Link: https://lore.kernel.org/r/20240508130618.2148631-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
In ptp_ocp driver pin actions assume sma_nr starts with 1, but for DPLL
subsystem callback 0-based index was used. Fix it providing proper index.
Fixes: 09eeb3aecc6c ("ptp_ocp: implement DPLL ops")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20240508132111.11545-1-vadim.fedorenko@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver Changes:
- Use ordered WQ for G2H handler. (Matthew Brost)
- Use flexible-array rather than zero-sized (Lucas De Marchi)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Zjz7SzCvfA3vQRxu@fedora
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
drm-misc-next-fixes for v6.10-rc1:
- panthor fixes.
- Reverting Kconfig changes, and moving drm options to submenu.
- Hide physical fb address in fb helper.
- zynqmp bridge fix.
- Revert broken ti-sn65dsi83 fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fe630414-d13e-4052-86f3-ce3155eb3e44@linux.intel.com
|
|
https://gitlab.freedesktop.org/drm/msm into drm-next
Updates for v6.10
Core:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings (no driver changes, using SM8350
as a fallback compat)
GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtpw6dNR9JBikFTQ=TCpt-9FeFW+SGjXWv+Jv3emm0Pbg@mail.gmail.com
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-fixes
- Fix use zero-length element array
- Move more from system wq to ordered private wq
- Do not ignore return for drmm_mutex_init
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c3rduifdp5wipkljdpuq4x6uowkc2uyzgdoft4txvp6mgvzjaj@7zw7c6uw4wrf
|
|
The media_pad_remote_pad_unique() function returns error pointers, not
NULL. Update the check accordingly.
Fixes: 392cd78d495f ("media: bcm2835-unicam: Add support for CCP2/CSI2 camera interface")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/fbbe7862-2820-44eb-81cb-7f33b99cca35@moroto.mountain
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
platform_get_irq() already prints an error for us.
Fix this cocci warning:
drivers/media/platform/broadcom/bcm2835-unicam.c:2664:2-9: line 2664 is redundant because platform_get_irq() already prints an error
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20240506-fix-broad-v2-2-e6a2a5c0d609@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
platform_get_irq() cannot return the value 0. It will either return a non-zero
irq or a errcode.
If a errcode is returned, we need to populate the error code upwards. It will
give a more accurate reason of why it failed to the caller, who might decide
to retry later.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240506-fix-broad-v2-1-e6a2a5c0d609@chromium.org
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240506100917.1544174-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
|
|
Lockdep reports the below circular locking dependency issue. The
mmap_lock acquisition while holding pci_bus_sem is due to the use of
copy_to_user() from within a pci_walk_bus() callback.
Building the devices array directly into the user buffer is only for
convenience. Instead we can allocate a local buffer for the array,
bounded by the number of devices on the bus/slot, fill the device
information into this local buffer, then copy it into the user buffer
outside the bus walk callback.
======================================================
WARNING: possible circular locking dependency detected
6.9.0-rc5+ #39 Not tainted
------------------------------------------------------
CPU 0/KVM/4113 is trying to acquire lock:
ffff99a609ee18a8 (&vdev->vma_lock){+.+.}-{4:4}, at: vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
but task is already holding lock:
ffff99a243a052a0 (&mm->mmap_lock){++++}-{4:4}, at: vaddr_get_pfns+0x3f/0x170 [vfio_iommu_type1]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&mm->mmap_lock){++++}-{4:4}:
__lock_acquire+0x4e4/0xb90
lock_acquire+0xbc/0x2d0
__might_fault+0x5c/0x80
_copy_to_user+0x1e/0x60
vfio_pci_fill_devs+0x9f/0x130 [vfio_pci_core]
vfio_pci_walk_wrapper+0x45/0x60 [vfio_pci_core]
__pci_walk_bus+0x6b/0xb0
vfio_pci_ioctl_get_pci_hot_reset_info+0x10b/0x1d0 [vfio_pci_core]
vfio_pci_core_ioctl+0x1cb/0x400 [vfio_pci_core]
vfio_device_fops_unl_ioctl+0x7e/0x140 [vfio]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x8d/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #2 (pci_bus_sem){++++}-{4:4}:
__lock_acquire+0x4e4/0xb90
lock_acquire+0xbc/0x2d0
down_read+0x3e/0x160
pci_bridge_wait_for_secondary_bus.part.0+0x33/0x2d0
pci_reset_bus+0xdd/0x160
vfio_pci_dev_set_hot_reset+0x256/0x270 [vfio_pci_core]
vfio_pci_ioctl_pci_hot_reset_groups+0x1a3/0x280 [vfio_pci_core]
vfio_pci_core_ioctl+0x3b5/0x400 [vfio_pci_core]
vfio_device_fops_unl_ioctl+0x7e/0x140 [vfio]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x8d/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #1 (&vdev->memory_lock){+.+.}-{4:4}:
__lock_acquire+0x4e4/0xb90
lock_acquire+0xbc/0x2d0
down_write+0x3b/0xc0
vfio_pci_zap_and_down_write_memory_lock+0x1c/0x30 [vfio_pci_core]
vfio_basic_config_write+0x281/0x340 [vfio_pci_core]
vfio_config_do_rw+0x1fa/0x300 [vfio_pci_core]
vfio_pci_config_rw+0x75/0xe50 [vfio_pci_core]
vfio_pci_rw+0xea/0x1a0 [vfio_pci_core]
vfs_write+0xea/0x520
__x64_sys_pwrite64+0x90/0xc0
do_syscall_64+0x8d/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
-> #0 (&vdev->vma_lock){+.+.}-{4:4}:
check_prev_add+0xeb/0xcc0
validate_chain+0x465/0x530
__lock_acquire+0x4e4/0xb90
lock_acquire+0xbc/0x2d0
__mutex_lock+0x97/0xde0
vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
__do_fault+0x31/0x160
do_pte_missing+0x65/0x3b0
__handle_mm_fault+0x303/0x720
handle_mm_fault+0x10f/0x460
fixup_user_fault+0x7f/0x1f0
follow_fault_pfn+0x66/0x1c0 [vfio_iommu_type1]
vaddr_get_pfns+0xf2/0x170 [vfio_iommu_type1]
vfio_pin_pages_remote+0x348/0x4e0 [vfio_iommu_type1]
vfio_pin_map_dma+0xd2/0x330 [vfio_iommu_type1]
vfio_dma_do_map+0x2c0/0x440 [vfio_iommu_type1]
vfio_iommu_type1_ioctl+0xc5/0x1d0 [vfio_iommu_type1]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x8d/0x170
entry_SYSCALL_64_after_hwframe+0x76/0x7e
other info that might help us debug this:
Chain exists of:
&vdev->vma_lock --> pci_bus_sem --> &mm->mmap_lock
Possible unsafe locking scenario:
block dm-0: the capability attribute has been deprecated.
CPU0 CPU1
---- ----
rlock(&mm->mmap_lock);
lock(pci_bus_sem);
lock(&mm->mmap_lock);
lock(&vdev->vma_lock);
*** DEADLOCK ***
2 locks held by CPU 0/KVM/4113:
#0: ffff99a25f294888 (&iommu->lock#2){+.+.}-{4:4}, at: vfio_dma_do_map+0x60/0x440 [vfio_iommu_type1]
#1: ffff99a243a052a0 (&mm->mmap_lock){++++}-{4:4}, at: vaddr_get_pfns+0x3f/0x170 [vfio_iommu_type1]
stack backtrace:
CPU: 1 PID: 4113 Comm: CPU 0/KVM Not tainted 6.9.0-rc5+ #39
Hardware name: Dell Inc. PowerEdge T640/04WYPY, BIOS 2.15.1 06/16/2022
Call Trace:
<TASK>
dump_stack_lvl+0x64/0xa0
check_noncircular+0x131/0x150
check_prev_add+0xeb/0xcc0
? add_chain_cache+0x10a/0x2f0
? __lock_acquire+0x4e4/0xb90
validate_chain+0x465/0x530
__lock_acquire+0x4e4/0xb90
lock_acquire+0xbc/0x2d0
? vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
? lock_is_held_type+0x9a/0x110
__mutex_lock+0x97/0xde0
? vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
? lock_acquire+0xbc/0x2d0
? vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
? find_held_lock+0x2b/0x80
? vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
vfio_pci_mmap_fault+0x35/0x1a0 [vfio_pci_core]
__do_fault+0x31/0x160
do_pte_missing+0x65/0x3b0
__handle_mm_fault+0x303/0x720
handle_mm_fault+0x10f/0x460
fixup_user_fault+0x7f/0x1f0
follow_fault_pfn+0x66/0x1c0 [vfio_iommu_type1]
vaddr_get_pfns+0xf2/0x170 [vfio_iommu_type1]
vfio_pin_pages_remote+0x348/0x4e0 [vfio_iommu_type1]
vfio_pin_map_dma+0xd2/0x330 [vfio_iommu_type1]
vfio_dma_do_map+0x2c0/0x440 [vfio_iommu_type1]
vfio_iommu_type1_ioctl+0xc5/0x1d0 [vfio_iommu_type1]
__x64_sys_ioctl+0x8a/0xc0
do_syscall_64+0x8d/0x170
? rcu_core+0x8d/0x250
? __lock_release+0x5e/0x160
? rcu_core+0x8d/0x250
? lock_release+0x5f/0x120
? sched_clock+0xc/0x30
? sched_clock_cpu+0xb/0x190
? irqtime_account_irq+0x40/0xc0
? __local_bh_enable+0x54/0x60
? __do_softirq+0x315/0x3ca
? lockdep_hardirqs_on_prepare.part.0+0x97/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f8300d0357b
Code: ff ff ff 85 c0 79 9b 49 c7 c4 ff ff ff ff 5b 5d 4c 89 e0 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 75 68 0f 00 f7 d8 64 89 01 48
RSP: 002b:00007f82ef3fb948 EFLAGS: 00000206 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f8300d0357b
RDX: 00007f82ef3fb990 RSI: 0000000000003b71 RDI: 0000000000000023
RBP: 00007f82ef3fb9c0 R08: 0000000000000000 R09: 0000561b7e0bcac2
R10: 0000000000000000 R11: 0000000000000206 R12: 0000000000000000
R13: 0000000200000000 R14: 0000381800000000 R15: 0000000000000000
</TASK>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240503143138.3562116-1-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
0 (part 2)
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
This is a follow up to commit d8a66f3621c2 ("hwmon: Drop explicit
initialization of struct i2c_device_id::driver_data to 0") which I
created before identifying a few corner cases in my conversion script.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240508072027.2119857-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Kbuild conventionally uses $(obj)/ for generated files, and $(src)/ for
checked-in source files. It is merely a convention without any functional
difference. In fact, $(obj) and $(src) are exactly the same, as defined
in scripts/Makefile.build:
src := $(obj)
When the kernel is built in a separate output directory, $(src) does
not accurately reflect the source directory location. While Kbuild
resolves this discrepancy by specifying VPATH=$(srctree) to search for
source files, it does not cover all cases. For example, when adding a
header search path for local headers, -I$(srctree)/$(src) is typically
passed to the compiler.
This introduces inconsistency between upstream and downstream Makefiles
because $(src) is used instead of $(srctree)/$(src) for the latter.
To address this inconsistency, this commit changes the semantics of
$(src) so that it always points to the directory in the source tree.
Going forward, the variables used in Makefiles will have the following
meanings:
$(obj) - directory in the object tree
$(src) - directory in the source tree (changed by this commit)
$(objtree) - the top of the kernel object tree
$(srctree) - the top of the kernel source tree
Consequently, $(srctree)/$(src) in upstream Makefiles need to be replaced
with $(src).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
|
|
Update tpm2_load_context() to return -EINVAL on integrity failures and
use this as a signal when loading the NULL context that something
might be wrong. If the signal fails, check the name of the NULL
primary against the one stored in the chip data and if there is a
mismatch disable the TPM because it is likely to have suffered a reset
attack.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
This is the last component of encrypted tpm2 session handling that
allows us to verify from userspace that the key derived from the NULL
seed genuinely belongs to the TPM and has not been spoofed.
The procedure for doing this involves creating an attestation identity
key (which requires verification of the TPM EK certificate) and then
using that AIK to sign a certification of the Elliptic Curve key over
the NULL seed. Userspace must create this EC Key using the parameters
prescribed in TCG TPM v2.0 Provisioning Guidance for the SRK ECC; if
this is done correctly the names will match and the TPM can then run a
TPM2_Certify operation on this derived primary key using the newly
created AIK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
If some entity is snooping the TPM bus, they can see the random
numbers we're extracting from the TPM and do prediction attacks
against their consumers. Foil this attack by using response
encryption to prevent the attacker from seeing the random sequence.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
tpm2_pcr_extend() is used by trusted keys to extend a PCR to prevent a
key from being re-loaded until the next reboot. To use this
functionality securely, that extend must be protected by a session
hmac. This patch adds HMAC protection so tampering with the
tpm2_pcr_extend() command in flight is detected.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The final pieces of the HMAC API are for manipulating the session area
of the command. To add an authentication HMAC session
tpm_buf_append_hmac_session() is called where tpm2_append_auth() would
go. If a non empty password is passed in, this is correctly added to
the HMAC to prove knowledge of it without revealing it. Note that if
the session is only used to encrypt or decrypt parameters (no
authentication) then tpm_buf_append_hmac_session_opt() must be used
instead. This functions identically to tpm_buf_append_hmac_session()
when TPM_BUS_SECURITY is enabled, but differently when it isn't,
because effectively nothing is appended to the session area.
Next the parameters should be filled in for the command and finally
tpm_buf_fill_hmac_session() is called immediately prior to transmitting
the command which computes the correct HMAC and places it in the
command at the session location in the tpm buffer
Finally, after tpm_transmit_cmd() is called,
tpm_buf_check_hmac_response() is called to check that the returned
HMAC matched and collect the new state for the next use of the
session, if any.
The features of the session are controlled by the session attributes
set in tpm_buf_append_hmac_session(). If TPM2_SA_CONTINUE_SESSION is
not specified, the session will be flushed and the tpm2_auth structure
freed in tpm_buf_check_hmac_response(); otherwise the session may be
used again. Parameter encryption is specified by or'ing the flag
TPM2_SA_DECRYPT and response encryption by or'ing the flag
TPM2_SA_ENCRYPT. the various encryptions will be taken care of by
tpm_buf_fill_hmac_session() and tpm_buf_check_hmac_response()
respectively.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> # crypto API parts
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Add tpm2_append_name() for appending to the handle area of the TPM
command. When TPM_BUS_SECURITY is enabled and HMAC sessions are in
use this adds the standard u32 handle to the buffer but additionally
records the name of the object which must be used as part of the HMAC
computation. The name of certain object types (volatile and permanent
handles and NV indexes) is a hash of the public area of the object.
Since this hash is not known ahead of time, it must be requested from
the TPM using TPM2_ReadPublic() (which cannot be HMAC protected, but
if an interposer lies about it, the HMAC check will fail and the
problem will be detected).
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> # crypto API parts
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Add session based HMAC authentication plus parameter decryption and
response encryption using AES. The basic design is to segregate all
the nasty crypto, hash and hmac code into tpm2-sessions.c and export a
usable API. The API first of all starts off by gaining a session with
tpm2_start_auth_session() which initiates a session with the TPM and
allocates an opaque tpm2_auth structure to handle the session
parameters. The design is that session use will be single threaded
from start to finish under the ops lock, so the tpm2_auth structure is
stored in struct tpm2_chip to simpify the externally visible API.
The session can be ended with tpm2_end_auth_session() which is
designed only to be used in error legs. Ordinarily the further
session API (future patches) will end or continue the session
appropriately without having to call this.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> # crypto API parts
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The TCG mandates two Key derivation functions called KDFa and KDFe
used to derive keys from seeds and elliptic curve points respectively.
The definitions for these functions are found in the TPM 2.0 Library
Specification Part 1 - Architecture Guide
https://trustedcomputinggroup.org/resource/tpm-library-specification/
Implement a cut down version of each of these functions sufficient to
support the key derivation needs of HMAC sessions.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The session handling code uses a "salted" session, meaning a session
whose salt is encrypted to the public part of another TPM key so an
observer cannot obtain it (and thus deduce the session keys). This
patch creates and context saves in the tpm_chip area the primary key
of the NULL hierarchy for this purpose.
[jarkko@kernel.org: fixed documentation errors]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
The TPM2 session HMAC and encryption handling code needs to save and
restore a single volatile context for the elliptic curve version of
the NULL seed, so export the APIs which do this for internal use.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Replace all instances of &buf.data[TPM_HEADER_SIZE] with a new
function tpm_buf_parameters() because encryption sessions change
where the return parameters are located in the buffer since if a
return session is present they're 4 bytes beyond the header with those
4 bytes giving the parameter length. If there is no return session,
then they're in the usual place immediately after the header.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Declare reader functions for the instances of struct tpm_buf. If the read
goes out of boundary, TPM_BUF_BOUNDARY_ERROR is set, and subsequent read
will do nothing.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
Declare tpm_buf_init_sized() and tpm_buf_reset_sized() for creating TPM2B
formatted buffers. These buffers are also known as sized buffers in the
specifications and literature.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
TPM2B buffers, or sized buffers, have a two byte header, which contains the
length of the payload as a 16-bit big-endian number, without counting in
the space taken by the header. This differs from encoding in the TPM header
where the length includes also the bytes taken by the header.
Unbound the length of a tpm_buf from the value stored to the TPM command
header. A separate encoding and decoding step so that different buffer
types can be supported, with variant header format and length encoding.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
