| Age | Commit message (Collapse) | Author |
|---|
|
Thomas reports:
"Windows:
00 diagnostics
01 modem
02 at-port
03 nmea
04 nic
Linux:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2001 ProdID=7e19 Rev=02.32
S: Manufacturer=Mobile Connect
S: Product=Mobile Connect
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage"
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The CP2105 is used in the GE Healthcare Remote Alarm Box, with the
Manufacturer ID of 0x1901 and Product ID of 0x0194.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
A Fedora user reports that the ftdi_sio driver works properly for the
ICP DAS I-7561U device. Further, the user manual for these devices
instructs users to load the driver and add the ids using the sysfs
interface.
Add support for these in the driver directly so that the devices work
out of the box instead of needing manual configuration.
Reported-by: <thesource@mail.ru>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
commit e2c8b8701e2d moved modeset locking inside resume/suspend
functions, but missed a code path only executed on lid close/open
on older hardware. The result was a deadlock when closing and
opening the lid without suspending on such hardware:
=============================================
[ INFO: possible recursive locking detected ]
4.6.0-rc1 #385 Not tainted
---------------------------------------------
kworker/0:3/88 is trying to acquire lock:
(&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
but task is already holding lock:
(&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&dev->mode_config.mutex);
lock(&dev->mode_config.mutex);
*** DEADLOCK ***
May be due to missing lock nesting notation
7 locks held by kworker/0:3/88:
#0: ("kacpi_notify"){++++.+}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
#1: ((&dpc->work)#2){+.+.+.}, at: [<ffffffff81068dfc>] process_one_work+0x14a/0x50b
#2: ((acpi_lid_notifier).rwsem){++++.+}, at: [<ffffffff8106f874>] __blocking_notifier_call_chain+0x34/0x65
#3: (&dev_priv->modeset_restore_lock){+.+.+.}, at: [<ffffffffa0664cf6>] intel_lid_notify+0x3c/0xd9 [i915]
#4: (&dev->mode_config.mutex){+.+.+.}, at: [<ffffffffa02d0d4f>] drm_modeset_lock_all+0x3e/0xa6 [drm]
#5: (crtc_ww_class_acquire){+.+.+.}, at: [<ffffffffa02d0d59>] drm_modeset_lock_all+0x48/0xa6 [drm]
#6: (crtc_ww_class_mutex){+.+.+.}, at: [<ffffffffa02d0b2a>] modeset_lock+0x13c/0x1cd [drm]
stack backtrace:
CPU: 0 PID: 88 Comm: kworker/0:3 Not tainted 4.6.0-rc1 #385
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
Workqueue: kacpi_notify acpi_os_execute_deferred
0000000000000000 ffff88022fd5f990 ffffffff8124af06 ffffffff825b39c0
ffffffff825b39c0 ffff88022fd5fa60 ffffffff8108f547 ffff88022fd5fa70
000000008108e817 ffff880230236cc0 0000000000000000 ffffffff825b39c0
Call Trace:
[<ffffffff8124af06>] dump_stack+0x67/0x90
[<ffffffff8108f547>] __lock_acquire+0xdb5/0xf71
[<ffffffff8108bd2c>] ? look_up_lock_class+0xbe/0x10a
[<ffffffff8108fae2>] lock_acquire+0x137/0x1cb
[<ffffffff8108fae2>] ? lock_acquire+0x137/0x1cb
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffff8148202f>] mutex_lock_nested+0x7e/0x3a4
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa063e6a4>] intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa063e6a4>] ? intel_display_resume+0x4a/0x12f [i915]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa02d0b2a>] ? modeset_lock+0x13c/0x1cd [drm]
[<ffffffffa02d0bf7>] ? drm_modeset_lock+0x17/0x24 [drm]
[<ffffffffa02d0c8b>] ? drm_modeset_lock_all_ctx+0x87/0xa1 [drm]
[<ffffffffa0664d6a>] intel_lid_notify+0xb0/0xd9 [i915]
[<ffffffff8106f4c6>] notifier_call_chain+0x4a/0x6c
[<ffffffff8106f88d>] __blocking_notifier_call_chain+0x4d/0x65
[<ffffffff8106f8b9>] blocking_notifier_call_chain+0x14/0x16
[<ffffffffa0011215>] acpi_lid_send_state+0x83/0xad [button]
[<ffffffffa00112a6>] acpi_button_notify+0x41/0x132 [button]
[<ffffffff812b07df>] acpi_device_notify+0x19/0x1b
[<ffffffff812c8570>] acpi_ev_notify_dispatch+0x49/0x64
[<ffffffff812ab9fb>] acpi_os_execute_deferred+0x14/0x20
[<ffffffff81068f17>] process_one_work+0x265/0x50b
[<ffffffff810696f5>] worker_thread+0x1fc/0x2dd
[<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
[<ffffffff810694f9>] ? rescuer_thread+0x309/0x309
[<ffffffff8106e2d6>] kthread+0xe0/0xe8
[<ffffffff8107bc47>] ? local_clock+0x19/0x22
[<ffffffff81484f42>] ret_from_fork+0x22/0x40
[<ffffffff8106e1f6>] ? kthread_create_on_node+0x1b5/0x1b5
Fixes: e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459328913-13719-1-git-send-email-bjorn@mork.no
(cherry picked from commit 9f54d4bd5808b5c892a44c539c126b71d299f341)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux into char-misc-linus
Kees briefly writes:
fixes some possible memory allocation leaks on error paths
|
|
The acpi_pcc_probe() may end up accessing memory outside of the PCCT
table space causing the kernel panic(). Increment the pcct_entry
pointer after parsing 'HW-reduced Communications Subspace' to fix
the problem. This change also enables the parsing of subtable at
index 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This frees the allocated page if there is a kmalloc failure.
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This case is supposed to read from a memory after it has been freed,
but we missed freeing base if the memory 'val' could not be allocated.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
This case is supposed to read from a page after after it is freed, but
it missed freeing val if we are not able to get a free page.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
into drm-fixes
Lots of misc bug fixes for radeon and amdgpu and one for ttm.
- fix vram info fetching on Fiji and unposted boards
- additional vblank fixes from the conversion to drm_vblank_on/off
- UVD dGPU suspend and resume fixes
- lots of powerplay fixes
- fix a fence leak in the pageflip code
- ttm fix for platforms where CPU is 32 bit, but physical addresses are >32bits
* 'drm-fixes-4.6' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: total vram size also reduces pin size
drm/amd/powerplay: add uvd/vce dpm enabling flag default.
drm/amd/powerplay: fix issue that resume back, dpm can't work on FIJI.
drm/amdgpu: save and restore the firwmware cache part when suspend resume
drm/amdgpu: save and restore UVD context with suspend and resume
drm/ttm: use phys_addr_t for ttm_bus_placement
drm/radeon: Only call drm_vblank_on/off between drm_vblank_init/cleanup
drm/amdgpu: fence wait old rcu slot
drm/amdgpu: fix leaking fence in the pageflip code
drm/amdgpu: print vram type rather than just DDR
drm/amdgpu/gmc: use proper register for vram type on Fiji
drm/amdgpu/gmc: move vram type fetching into sw_init
drm/amdgpu: Set vblank_disable_allowed = true
drm/radeon: Set vblank_disable_allowed = true
drm/amd/powerplay: Need to change boot to performance state in resume.
drm/amd/powerplay: add new Fiji function for not setting same ps.
drm/amdgpu: check dpm state before pm system fs initialized.
drm/amd/powerplay: notify amdgpu whether dpm is enabled or not.
drm/amdgpu: Not support disable dpm in powerplay.
drm/amdgpu: add an cgs interface to notify amdgpu the dpm state.
...
|
|
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I noticed my monitor didn't power off when it should,
this should fix it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This ports the DAL timeouts and MST rate calculations
for the hw from the DAL codebase.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I'm back from PTO. These issues cropped up while I was gone and are
simple fixes. I'll have more after I've caught up, but I wanted to
get these in quick.
Two minor fixes for 4.6-rc2:
- Fix mlx5 build error when on demand paging is not enabled
- Fix possible uninit variable in new i40iw driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: avoid potential uninitialized variable use
IB/mlx5: fix VFs callback function prototypes
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc finds that the i40iw_make_cm_node() function in the recently added
i40iw driver uses an uninitilized variable as an index into an array
if CONFIG_IPV6 is disabled and the driver uses IPv6 mode:
drivers/infiniband/hw/i40iw/i40iw_cm.c: In function 'i40iw_make_cm_node':
drivers/infiniband/hw/i40iw/i40iw_cm.c:2206:52: error: 'arpindex' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ether_addr_copy(cm_node->rem_mac, iwdev->arp_table[arpindex].mac_addr);
As far as I can tell, this code path can not be used because the ipv4
variable is always set with CONFIG_IPV6 is disabled, but it's better
to be sure and prevent the undefined behavior, as well as shut up
that warning in a proper way.
This adds an 'else' clause for the case we get the warning about,
causing the function to return an error in a controlled way.
To avoid adding extra mess with combined io()/#ifdef clauses,
I'm also converting the existing #ifdef into a more readable
if(IS_ENABLED()) check.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f27b4746f378 ("i40iw: add connection management code")
Acked-by: Mustafa Ismail <Mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The previous patch that added a couple of callback functions put
the declarations inside of an #ifdef CONFIG_INFINIBAND_ON_DEMAND_PAGING,
which causes the build to fail if that option is disabled:
drivers/infiniband/hw/mlx5/main.c: In function 'mlx5_ib_add':
drivers/infiniband/hw/mlx5/main.c:2358:31: error: 'mlx5_ib_get_vf_config' undeclared (first use in this function)
This moves the four declarations below the #ifdef section so they
are always available.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eff901d30e6c ("IB/mlx5: Implement callbacks for manipulating VFs")
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Currently drivers are limited to 19 slots for cyclic transfers.
However, if the DMA burst size is the same as the period size,
the period size can be changed to the full buffer size and
intermediate interrupts activated. Since intermediate interrupts
will trigger for each burst and the burst size is the same as
the period size, the driver will get interrupts each period as
expected. This has the benefit of allowing the functionality of
many more slots, but only uses 2 slots.
This workaround is only active if more than 19 slots are needed
and the burst size matches the period size.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The dynamic or on demand pm_runtime does not work correctly on am335x and
am437x due to interference with hwmod.
Fall back using the pm_runtime usage as it was in the old driver stack,
meaning that at probe time call pm_runtime_enable() and
pm_runtime_get_sync() for the TPTCs as well.
Fixes: 1be5336bc7ba ("dmaengine: edma: New device tree binding")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Since commit 7ace8fc8219e ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
BXT-M is a Intel Broxton SoC based platform with unique PCI ID.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Just a single fix to prevent GM20B systems hanging at boot.
* 'linux-4.6' of git://github.com/skeggsb/linux:
drm/nouveau/tegra: acquire and enable reference clock if needed
|
|
GM20B requires an extra clock compared to GK20A. Add that information
into the platform data and acquire and enable this clock if necessary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
arm hdlcd fix.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm: ARM HDLCD - fix an error code
drm: ARM HDLCD - get rid of devm_clk_put()
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm: stricter plane parameter checking, dw_hdmi-imx and dmfc fixes
- Check whether plane parameters comply with IPU IDMAC limitations and
fix planar YUV 4:2:0 U/V offsets and stride
- Cleanup encoder in dw_hdmi-imx bind error path and
remove a superfluous platform_set_drvdata in dw_hdmi-imx
- DMFC setup fixes: lock the ipu_dmfc_init_channel function against
concurrent use, rename it to ipu_dmfc_config_wait4eot, and call
it after the FIFO size has been determined.
* tag 'imx-drm-next-2016-04-01' of git://git.pengutronix.de/git/pza/linux:
drm/imx: Don't set a gamma table size
drm/imx: ipuv3-plane: Configure DMFC wait4eot bit after slots are determined
gpu: ipu-v3: ipu-dmfc: Rename ipu_dmfc_init_channel to ipu_dmfc_config_wait4eot
gpu: ipu-v3: ipu-dmfc: Make function ipu_dmfc_init_channel() return void
gpu: ipu-v3: ipu-dmfc: Protect function ipu_dmfc_init_channel() with mutex
drm/imx: dw_hdmi: Don't call platform_set_drvdata()
drm/imx: dw_hdmi: Call drm_encoder_cleanup() in error path
drm/imx: ipuv3-plane: fix planar YUV 4:2:0 support
drm/imx: ipuv3-plane: Add more thorough checks for plane parameter limitations
gpu: ipu-cpmem: modify ipu_cpmem_set_yuv_planar_full for better control
|
|
The 82544 has code that adds one additional descriptor per data buffer.
However we weren't taking that into account when determining the descriptors
needed for the next transmit at the end of the xmit_frame path.
This change takes that into account by doubling the number of descriptors
needed for the 82544 so that we can avoid a potential issue where we could
hang the Tx ring by loading frames with xmit_more enabled and then stopping
the ring without writing the tail.
In addition it adds a few more descriptors to account for some additional
workarounds that have been added over time.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current code path is capable of grossly overestimating the number of
descriptors needed to transmit a new frame. This specifically occurs if
the skb contains a number of 4K pages. The issue is that the logic for
determining the descriptors needed is ((S) >> (X)) + 1. When X is 12 it
means that we were indicating that we required 2 descriptors for each 4K
page when we only needed one.
This change corrects this by instead adding (1 << (X)) - 1 to the S value
instead of adding 1 after the fact. This way we get an accurate descriptor
needed count as we are essentially doing a DIV_ROUNDUP().
Reported-by: Ivan Suzdal <isuzdal@mirantis.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There was an error introduced with commit 3fced535079a ("i40e: X722 is
on the IOSF bus and does not report the PCI bus info"), where code was
added but the enabling flag is never set.
CC: Anjali Singhai Jain <anjali.singhai@intel.com>
CC: Stefan Assman <sassman@redhat.com>
Fixes: 3fced535079a ("i40e: X722 is on the IOSF bus ...")
Reported-by: Steve Best <sbest@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Commit 5c5fb40de8f1 ("PCI: imx6: Add support for active-low reset GPIO")
cause regressions on some boards like MX6 Gateworks Ventana, for example.
The reason for the breakage is that this commit sets the GPIO polarity in
the wrong logic level.
Also, the commit log is wrong because active-low reset GPIO is what the
driver used to support since the beginning.
So keep the old behavior that ignores the GPIO polarity specified in the
device tree and treat the PCI reset GPIO as active-low.
Reported-by: Krzysztof Hałasa <khalasa@piap.pl>
Tested-by: Tim Harvey <tharvey@gateworks.com> # Gateworks Ventana
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
CC: stable@vger.kernel.org # v4.5+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes here that came in since the merge
window plus one core fix for locking in cases where a client driver
grabs a lock on the whole bus for an extended series of operations
that was introduced by the changes to support accelerated flash
operations"
* tag 'spi-fix-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: rockchip: fix probe deferral handling
spi: omap2-mcspi: fix dma transfer for vmalloced buffer
spi: fix possible deadlock between internal bus locks and bus_lock_flag
spi: imx: Fix possible NULL pointer deref
spi: imx: only do necessary changes to ECSPIx_CONFIGREG
spi: rockchip: Spelling s/divsor/divisor/
|
|
As of 5a60e87603c4c533492c515b7f62578189b03c9c, RBD object request
allocations are made via rbd_obj_request_create() with GFP_NOIO.
However, subsequent OSD request allocations in rbd_osd_req_create*()
use GFP_ATOMIC.
With heavy page cache usage (e.g. OSDs running on same host as krbd
client), rbd_osd_req_create() order-1 GFP_ATOMIC allocations have been
observed to fail, where direct reclaim would have allowed GFP_NOIO
allocations to succeed.
Cc: stable@vger.kernel.org # 3.18+
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Suggested-by: Neil Brown <neilb@suse.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
When client request a non existing channel from of_dma_xilinx_xlate
we get a NULL pointer dereferencing. This patch fix this problem.
Signed-off-by: Franck Jullien <franck.jullien@odyssee-systemes.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This adds the VID/PID combination for the Xbox One version of the Mad
Catz FightStick TE 2.
The functionality that this provides is about on par with what the
Windows drivers for the stick manage to deliver.
What works:
- Digital stick
- 6 main buttons
- Xbox button
- The two buttons on the back
- The locking buttons (preventing accidental Xbox button press)
What doesn't work:
- Two of the main buttons (don't work on Windows either)
- The "Haptic" button setting does not have an effect (not sure if it
works on Windows)
I added the MAP_TRIGGERS_TO_BUTTONS option but in my (limited) testing
there was no practical difference with or without. The FightStick does
not have triggers though so adding it makes sense.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
If the client queues up more transfers the driver will not able to move to
the next transfer without knowing that the previous descriptor is
completed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When based on the CCR_ENABLE bit the channel is stopped we should not call
omap_dma_callback(), only change the return value to DMA_COMPLETE. Client
drivers will do the right thing to clean up the channel after the transfer
has been completed.
Check the CCR_ENABLE only if the channel is running and not paused since
pause in sDMA means that the channel is stopped.
This will fix one hard to reproduce race condition when the channel is
terminated during transfer (affecting cyclic operation).
Fixes: 1a7cf7b26f25 ("dmaengine: omap-dma: Handle cases when the channel is polled for completion")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
A tablet PC booted into Windows may have its pen/touch hardware switched
into "Wacom mode" similar to what we do with explicitly-supported hardware.
Some devices appear to maintain this state across reboots, preventing their
use with the generic HID driver. This patch adds support for detecting the
presence of the mode switch feature report used by devices based on the G9
and G11 chips and has the HID codepath always attempt to reset the device
back to sending standard HID reports.
Fixes: https://sourceforge.net/p/linuxwacom/bugs/307/
Fixes: https://sourceforge.net/p/linuxwacom/bugs/310/
Fixes: https://github.com/linuxwacom/input-wacom/issues/15
Co-authored-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Commit 5ae6e89 introduced hid_data.inputmode with a comment that it
would have the value -1 if undefined, but then forgot to actually
perform the initialization. Although this doesn't appear to have
caused any problems in practice, it should still be remedied.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here is a set of pin control fixes for the v4.6 series.
A bit bigger than what I hoped for, but all fixes are confined to
drivers, a few of them also targeted to stable.
Summary:
- On Super-H PFC (Renesas) controllers: only use dummies on legacy
systems. This fixes a serious ethernet regression on a Renesas
board.
- Pistachio: Fix errors in the pin table.
- Allwinner SunXi: fix the external interrupts to work.
- Intel: fix so the high level interrupts start working, and fix a
spurious interrupt issue.
- Qualcomm ipq4019: fix the number of GPIOs provided (bump to 100),
correct register offsets and handle GPIO mode properly.
- Revert the revert on the revert so that Xway has a .to_irq()
callback again.
- Minor fixes to errorpaths and debug info.
- A MAINTAINERS update"
* tag 'pinctrl-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
Revert "Revert "pinctrl: lantiq: Implement gpio_chip.to_irq""
pinctrl: qcom: ipq4019: fix register offsets
pinctrl: qcom: ipq4019: fix the function enum for gpio mode
pinctrl: qcom: ipq4019: set ngpios to correct value
pinctrl: nomadik: fix pull debug print inversion
MAINTAINERS: pinctrl: samsung: Add two new maintainers
pinctrl: intel: implement gpio_irq_enable
pinctrl: intel: make the high level interrupt working
pinctrl: freescale: imx: fix bogus check of of_iomap() return value
pinctrl: sunxi: Fix A33 external interrupts not working
pinctrl: pistachio: fix mfio84-89 function description and pinmux.
pinctrl: sh-pfc: only use dummy states for non-DT platforms
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some bug fixes on au0828 and snd-usb-audio:
- the au0828+snd-usb-audio MC patch broke several things and produced
some race conditions. Better to revert the patches, and re-work on
them for a next version
- fix a regression at tuner disable links logic
- properly handle dev_state as a bitmask"
* tag 'media/v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Revert "[media] media: au0828 change to use Managed Media Controller API"
[media] Revert "[media] sound/usb: Use Media Controller API to share media resources"
[media] au0828: Fix dev_state handling
[media] au0828: fix au0828_v4l2_close() dev_state race condition
[media] media: au0828 fix to clear enable/disable/change source handlers
[media] v4l2-mc: cleanup a warning
[media] au0828: disable tuner links and cache tuner/decoder
|
|
With the change to stashing just the IOVA-page-aligned remainder of the
CPU-page offset rather than the whole thing, the failure path in
__invalidate_sg() also needs tweaking to account for that in the case of
differing page sizes where the two offsets may not be equivalent.
Similarly in __finalise_sg(), lest the architecture-specific wrappers
later get the wrong address for cache maintenance on sync or unmap.
Fixes: 164afb1d85b8 ("iommu/dma: Use correct offset in map_sg")
Reported-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Cc: stable@ver.kernel.org # v4.4+
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Adds missing include that resulted in implicit device tree functions errors.
Fixes: 7b651706712b ("hwrng: bcm63xx - add device tree support")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
|
|
The patch "scsi: rescan VPD attributes" introduced a regression in which
devices that don't support VPD were being scanned for VPD attributes
anyway. This could cause issues for some devices and should be avoided
so the check for scsi_level has been moved out of scsi_add_lun and into
scsi_attach_vpd so that all callers will not scan VPD for devices that
don't support it.
[mkp: Merge fix]
Fixes: 09e2b0b14690 ("scsi: rescan VPD attributes")
Cc: <stable@vger.kernel.org> #v4.5+
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add support and PCI IDs for more Broxton host controllers
Other BXT IDs were added in v4.4 so cc'ing stable. This patch
is dependent on commit 163cbe31e516 ("mmc: sdhci-pci: Fix card
detect race for Intel BXT/APL") but that is already in stable
since v4.4.4.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
One of the VESA DMT timings in drm_dmt_modes[] is slightly off.
1024x768@43Hz (interlaced) vsync_end should be 776, not 772.
This brings it into line with the identical timings in edid_est_modes[].
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160404193639.8631D6E66B@gabe.freedesktop.org
|
|
This effectively reverts
commit 8e5fd599eb219f1054e39b40d18b217af669eea9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 9 13:28:50 2014 +0300
drm/i915/chv: Make CHV irq handler loop until all interrupts are consumed
as under continuous execlists load we can saturate the IRQ handler,
destablising the tsc clock and triggering the NMI watchdog to declare a hung
CPU.
[ 552.756051] clocksource: timekeeping watchdog on CPU0: Marking clocksource 'tsc' as unstable because the skew is too large:
[ 552.756080] clocksource: 'refined-jiffies' wd_now: 10003b480 wd_last: 10003b28c mask: ffffffff
[ 552.756091] clocksource: 'tsc' cs_now: d55d31aa50 cs_last: d17446166c mask: ffffffffffffffff
[ 552.756210] clocksource: Switched to clocksource refined-jiffies
[ 575.217870] NMI watchdog: Watchdog detected hard LOCKUP on cpu 1
[ 575.217893] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.5.0-rc7+ #18
[ 575.217905] Hardware name: /NUC5CPYB, BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[ 575.217915] 0000000000000000 ffff88027fd05bc0 ffffffff81288c6d 0000000000000000
[ 575.217935] 0000000000000001 ffff88027fd05be0 ffffffff810e72d1 0000000000000000
[ 575.217951] ffff88027fd05c80 ffff88027fd05c20 ffffffff81114b60 0000000181015f1e
[ 575.217967] Call Trace:
[ 575.217973] <NMI> [<ffffffff81288c6d>] dump_stack+0x4f/0x72
[ 575.217994] [<ffffffff810e72d1>] watchdog_overflow_callback+0x151/0x160
[ 575.218003] [<ffffffff81114b60>] __perf_event_overflow+0xa0/0x1e0
[ 575.218016] [<ffffffff811154c4>] perf_event_overflow+0x14/0x20
[ 575.218028] [<ffffffff8101d2ca>] intel_pmu_handle_irq+0x1da/0x460
[ 575.218042] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218052] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218064] [<ffffffff81014ae8>] perf_event_nmi_handler+0x28/0x50
[ 575.218075] [<ffffffff81007540>] nmi_handle+0x60/0x130
[ 575.218086] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218096] [<ffffffff810079c0>] do_nmi+0x140/0x470
[ 575.218108] [<ffffffff81559ec7>] end_repeat_nmi+0x1a/0x1e
[ 575.218119] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218129] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218139] [<ffffffff814a8aae>] ? poll_idle+0x3e/0x70
[ 575.218148] <<EOE>> [<ffffffff814a8353>] cpuidle_enter_state+0xf3/0x2f0
[ 575.218164] [<ffffffff814a8587>] cpuidle_enter+0x17/0x20
[ 575.218175] [<ffffffff810aaa3a>] call_cpuidle+0x2a/0x40
[ 575.218185] [<ffffffff810aade3>] cpu_startup_entry+0x273/0x330
[ 575.218196] [<ffffffff81033a1e>] start_secondary+0x10e/0x130
However, not servicing all available IIR within the handler does hurt the
throughput of pathological nop execbuf by about 20%, with a similar effect
upon the dispatch latency of a series of execbuf.
v2: use do {} while(0) for a smaller patch, and easier to revert again
I have reasonable confidence that we do not miss GT interrupts (as
execlists provides a stress case with a failure mechanism easily
detected by igt), however I have less confidence about all the other
sources of interrupts and worry that may lose a display hotplug
interrupt, for example.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93467
Testcase: igt/gem_exec_nop/basic # requires NMI watchdog
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Antti Koskipää <antti.koskipaa@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457946117-6714-1-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 579de73b048a0a4c66c25a033ac76a2836e0cf73)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Since we need MST devices ready before we try to resume displays,
calling this after intel_display_resume() can result in some issues with
various laptop docks where the monitor won't turn back on after
suspending the system.
This order was originally changed in
commit e7d6f7d70829 ("drm/i915: resume MST after reading back hw state")
In order to fix some unclaimed register errors, however the actual cause
of those has since been fixed.
CC: stable@vger.kernel.org
Signed-off-by: Lyude <cpaul@redhat.com>
[danvet: Resolve conflicts with locking changes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit a16b7658f4e0d4aec9bc3e75a5f0cc3f7a3a0422)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
