| Age | Commit message (Collapse) | Author |
|---|
|
NIX uses unique channel numbers to identify the packet sources/sinks
like CGX,LBK and SDP. The channel numbers assigned to each block are
hardwired in CN9xxx silicon.
The fixed channel numbers in CN9xxx are:
0x0 | a << 8 | b - LBK(0..3)_CH(0..63)
0x0 | a << 8 - Reserved
0x700 | a - SDP_CH(0..255)
0x800 | a << 8 | b << 4 | c - CGX(0..7)_LMAC(0..3)_CH(0..15)
All the channels in the above fixed enumerator(with maximum
number of blocks) are not required since some chips
have less number of blocks.
For CN10K silicon the channel numbers need to be programmed by
software in each block with the base channel number and range of
channels. This patch calculates and assigns the channel numbers
to efficiently distribute the channel number range(0-4095) among
all the blocks. The assignment is made based on the actual number of
blocks present and also contiguously leaving no holes.
The channel numbers remaining after the math are used as new CPT
replay channels present in CN10K. Also since channel numbers are
not fixed the transmit channel link number needed by AF consumers
is calculated by AF and sent along with nix_lf_alloc mailbox response.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OcteonTx2's next gen platform the CN10K has RPM MAC which has a
different serdes when compared to CGX MAC. Though the underlying
HW is different, the CSR interface has been designed largely inline
with CGX MAC, with few exceptions though. So we are using the same
CGX driver for RPM MAC as well and will have a different set of APIs
for RPM where ever necessary.
This patch adds initial support for CN10K's RPM MAC i.e. the driver
registration, communication with firmware etc. For communication with
firmware, RPM provides a different IRQ when compared to CGX.
The CGX and RPM blocks support different features. Currently few
features like ptp, flowcontrol and higig are not supported by RPM. This
patch adds new mailbox message "CGX_FEATURES_GET" to get the list of
features supported by underlying MAC.
RPM has different implementations for RX/TX stats. Unlike CGX,
bar offset of stat registers are different. This patch adds
support to access the same and dump the values in debugfs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to use new LMTST lines for NPA batch free
and burst SQE flush. Adds new dev_hw_ops structure to hold platform
specific functions and create new files cn10k.c and cn10k.h.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On CN10K platform transmit/receive buffer alloc and free from/to hardware
had changed to support burst operation. Whereas pervious silicon's only
support single buffer free at a time.
To Support the same firmware allocates a DRAM region for each PF/VF for
storing LMTLINES. These LMTLINES are used for NPA batch free and for
flushing SQE to the hardware.
PF/VF LMTST region is accessed via BAR4. PFs LMTST region is followed
by its VFs mbox memory. The size of region varies from 2KB to 256KB based
on number of LMTLINES configured.
This patch adds support for
- Mapping PF/VF LMTST region.
- Reserves 0-71 (RX + TX + XDP) LMTST lines for NPA batch
free operation.
- Reserves 72-512 LMTST lines for NIX SQE flush.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On CN10K platform NIX RQ and SQ context structure got changed.
This patch uses new mbox message "NIX_CN10K_AQ_ENQ" for NIX
context initialization on CN10K platform.
This patch also updates the nix_rx_parse_s and nix_sqe_sg_s
structures to add packet steering bit feilds.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On CN10K platform NPA and NIX context structure bit fields
had changed to support new features like bandwidth steering etc.
This patch dumps approprate context for CN10K platform.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NIX hardware context structure got changed to accommodate new
features like bandwidth steering, L3/L4 outer/inner checksum
enable/disable etc., on CN10K platform.
This patch defines new mbox message NIX_CN10K_AQ_INST for new
NIX context initialization.
This patch also updates the NPA context structures to accommodate
bit field changes made for CN10K platform.
This patch also removes Big endian bit fields from existing
structures as its support got deprecated in current and upcoming silicons.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitate communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
The patch also adds new hw_cap flag to setting hw features like TSO etc
and removes platform specific name from the PF/VF driver name to make it
appropriate for all supported platforms
This patch also removes platform specific name from the PF/VF driver name
to make it appropriate for all supported platforms
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitates communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
This patch also adds CN10K PTP subsystem and device IDs to ptp
driver id table.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch check that TX FC firmware is running in CM3.
If not, global TX FC would be disabled.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix GMAC TX flow control autoneg.
Flow control autoneg wrongly were disabled with enabled TX
flow control.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New FIFO flow control feature was added in PPv23.
PPv2 FIFO polled by HW and trigger pause frame if FIFO
fill level is below threshold.
FIFO HW flow control enabled with CM3 RXQ&BM flow
control with ethtool.
Current FIFO thresholds is:
9KB for port with maximum speed 10Gb/s port
4KB for port with maximum speed 5Gb/s port
2KB for port with maximum speed 1Gb/s port
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PP2v23 hardware supports a feature allowing to double the
size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add ethtool flow control configuration support.
Tx flow control retrieved correctly by ethtool get function.
FW per port ethtool configuration capability added.
Patch also takes care about mtu change procedure, if PPv2 switch
BM pools during mtu change.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds RXQ flow control configurations.
Flow control disabled by default.
Minimum ring size limited to 1024 descriptors.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables global flow control in FW and in the phylink validate mask.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware needs to monitor the RX Non-occupied descriptor
bits for flow control to move to XOFF mode.
These bits need to be unmasked to be functional, but they will
not raise interrupts as we leave the RX exception summary
bit in MVPP2_ISR_RX_TX_MASK_REG clear.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Flow Control periodic timer would be used if port in
XOFF to transmit periodic XOFF frames.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BM pool and RXQ size increased to support Firmware Flow Control.
Minimum depletion thresholds to support FC are 1024 buffers.
BM pool size increased to 2048 to have some 1024 buffers
space between depletion thresholds and BM pool size.
Jumbo frames require a 9888B buffer, so memory requirements
for data buffers increased from 7MB to 24MB.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add PPv23 version definition.
PPv23 is new packet processor in CP115.
Everything that supported by PPv22, also supported by PPv23.
No functional changes in this stage.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we have PP2v1 and PP2v2 hw-versions, with some different
handlers depending upon condition hw_version = MVPP21/MVPP22.
In a future there will be also PP2v3. Let's use now the generic
"if equal/notEqual MVPP21" for all cases instead of "if MVPP22".
This patch does not change any functionality.
It is not intended to introduce PP2v3.
It just modifies MVPP21/MVPP22 check-condition
bringing it to generic and unified form correct for new-code
introducing and PP2v3 net-next generation.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds CM3 memory map.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support the possibility of per-device event channel
settings (e.g. lateeoi spurious event thresholds) add a xenbus device
pointer to struct irq_info() and modify the related event channel
binding interfaces to take the pointer to the xenbus device as a
parameter instead of the domain id of the other side.
While at it remove the stale prototype of bind_evtchn_to_irq_lateeoi().
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of a common event for rx and tx queue the event should be
regarded to be spurious if no rx and no tx requests are pending.
Unfortunately the condition for testing that is wrong causing to
decide a event being spurious if no rx OR no tx requests are
pending.
Fix that plus using local variables for rx/tx pending indicators in
order to split function calls and if condition.
Fixes: 23025393dbeb3b ("xen/netback: use lateeoi irq binding")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-for-upstream-2021-02-10
Misc cleanups and trivial fixes for net-next
1) spelling mistakes
2) error path checks fixes
3) unused includes and struct fields cleanup
4) build error when MLX5_ESWITCH=no
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The running fw.psid version is in decimal format but the stored
fw.psid is in hex format. This can mislead the user to reset the
NIC to activate the stored version to become the running version.
Fix it to display the stored fw.psid in decimal format.
Fixes: 1388875b3916 ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If set_link_state() fails for any reason, we still cleanup the adapter
state and cannot recover from a partial close anyway. So set the adapter
to CLOSED state. That way if a new soft/hard reset is processed, the
adapter will remain in the CLOSED state until the next ibmvnic_open().
Fixes: 01d9bd792d16 ("ibmvnic: Reorganize device close")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several years ago these two entries have been added, but it's not clear
why. There's no trace that there has ever been such a chip version, and
not even the r8101 vendor driver knows these id's. So let's disable
detection, and if nobody complains remove them completely later.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bond driver needs to be patched to support new ethtool speeds.
Currently it emits a single warning [1] when it encounters an unknown
speed. As evident by the two previous patches, this is not explicit
enough. Instead, promote it to an error.
[1]
bond10: (slave swp1): unknown ethtool speed (200000) for port 1 (set it to 0)
v2:
* Use pr_err_once() instead of WARN_ONCE()
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to be able to use 3ad mode with 400G devices we need to extend
the supported speeds.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to be able to use 3ad mode with 200G devices we need to extend
the supported speeds.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Here we do the initialization of coalescing values on load.
per queue coalesce values are also restored across up/down of
ethernet interface.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
per queue coalescing allows better and more finegrained control
over interrupt rates.
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle netpoll case when qede_poll is called by
netpoll layer with budget 0
Signed-off-by: Bhaskar Upadhaya <bupadhaya@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, a random stack value is being returned because variable
_ret_ is not properly initialized. This variable is actually not
used anymore and it should be removed.
Fix this by removing all instances of variable ret and return 0.
Fixes: 64749c9c38a9 ("net: hns3: remove redundant return value of hns3_uninit_all_ring()")
Addresses-Coverity-ID: 1501700 ("Uninitialized scalar variable")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
plat_dat is initialized by stmmac_probe_config_dt().
So, initialization is not required by priv->plat.
This removes unnecessary initialization and variables.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far we don't re-configure WOL-related register bits when waking up
from hibernation. I'm not aware of any problem reports, but better
play safe and call __rtl8169_set_wol() in the resume() path too.
To achieve this move calling __rtl8169_set_wol() to
rtl8169_net_resume() and rename the function to rtl8169_runtime_resume().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the operations to set desired mode and retrieve the current
mode.
This feature was tested with an IP101G.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP101G provides three counters: RX packets, CRC errors and symbol
errors. The error counters can be configured to clear automatically on
read. Unfortunately, this isn't true for the RX packet counter. Because
of this and because the RX packet counter is more likely to overflow,
than the error counters implement only support for the error counters.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Registers >= 16 are paged. Be sure to set the page. It seems this was
working for now, because the default is correct for the registers used
in the driver at the moment. But this will also assume, nobody will
change the page select register before linux is started. The page select
register is _not_ reset with a soft reset of the PHY.
To ease the function reuse between the non-paged register space of the
IP101A and the IP101G, add noop read_page()/write_page() callbacks so
the IP101G functions can also be used for the IP101A.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This bit is reserved as 'always-write-1'. While this is not a particular
error, because we are only setting it, guard it by checking the model to
prevent errors in the future.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unfortunately, the IP101A and IP101G share the same PHY identifier.
While most of the functions are somewhat backwards compatible, there is
for example the APS_EN bit on the IP101A but on the IP101G this bit
reserved. Also, the IP101G has many more functionalities.
Deduce the model by accessing the page select register which - according
to the datasheet - is not available on the IP101A. If this register is
writable, assume we have an IP101G.
Split the combined IP101A/G driver into two separate drivers.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY core already resets the PHY before .config_init() if a
.soft_reset() op is registered. Drop the open-coded ip1xx_reset().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't sometimes use the address operator and sometimes not. Drop it and
make the code look uniform.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the datasheet of the IP101A/G there is no revision field
and MII_PHYSID2 always reads as 0x0c54. Use PHY_ID_MATCH_EXACT() then.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simpify the initializations of the structures. There is no functional
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.
Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a PD notifier event arrives, a new work event won't be enqueued if
the current one hasn't completed. This could lead to dropped events.
So, flush any pending work before scheduling the new instance.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210211193221.610867-1-pmalani@chromium.org
Signed-off-by: Benson Leung <bleung@chromium.org>
|
