| Age | Commit message (Collapse) | Author |
|---|
|
The i2c init/fini functions just register the i2c adapter.
There is no need to call them during hw init/fini. They only
need to be called once per driver init/fini. The previous
behavior broke runtime pm because we unregistered the i2c
adapter during suspend.
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Display goes blank after driver installation.
Aux tuning parameters must be used for 2.x only.
Wrong dc_golden_table offset was used.
[How]
Implement a new enc3_hw_init function without VBIOS constants usage to
be called for 3.x
Calculate dc_golden_table offset using sum of
base dce_info offset and golden table offset
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During SetPathMode and UpdatePlanes, the plane state can be null. We default
to linear swizzle mode when plane state is null. This resulted in bandwidth
validation failing when trying to set 8K60 mode (which previously passed validation
during rebuild timing list).
[How]
Change the default swizzle mode from linear to 4kb_s and update pitch accordingly.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[How]
Use dc_is_hdmi_signal to determine signal type.
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Sink OUI supported cap is not set so driver skips programming it.
[How]
Revert the change the skips OUI programming if the cap is not set
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why&How]
use correct logger context
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For ver.4.4 and higher VBIOS contains default setting table.
{How]
Read Golden Settings Table from VBIOS, apply Aux tuning parameters.
Signed-off-by: Igor Kravchenko <Igor.Kravchenko@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enable GFXOFF for navy_flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
1. For Navi12, CHIP_SIENNA_CICHLID, skip tmr load operation;
2. Check pointer before release firmware.
v2: use CHIP_SIENNA_CICHLID instead
v3: remove local "bool ret"; fix grammer issue
v4: use my name instead of "root"
v5: fix grammer issue and indent issue
Signed-off-by: Liu ChengZhe <ChengZhe.Liu@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Assigning false to block->status.hw overwrites PSP's previous
hardware status, which causes the PSP to Resume operation after
hardware init.
Remove this assignment and let the PSP execute Resume operation
when it is told to.
v2: Remove the braces.
v3: Modify the description.
Signed-off-by: Liu ChengZhe <ChengZhe.Liu@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update GC golden setting for navy_flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's in accordance with pmfw 65.5.0 for navy_flounder.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It doesn't expose PPTable descriptor on APU platform. So max/min
temperature values cannot be got from APU platform.
v2: Stoney needs to skip crit temperature as well.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Test expects that we also read HPD_IRQ_VECTOR when checking for
symbol loss as well lane status.
[How]
Read bytes 0x200-0x205 instead of just 0x202-0x205
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.
[How]
Set flag to force psr to use hw lock mgr.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Each asic can optimize best based on its capabilities
[How]
Optimizing timing for a new pixel clock
Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Programming DCN is explicitly forbidden during idle optimzations allowed
state. Existing implemenation relies on OS/DM, which is not robust. Instead
DC should sequence this.
Note that DC will not re-enter idle optimized state on its own, it is only
responsible for catching out of sequence calls. It is still DM
responsibility to sequence appropriate for optimized power, but this change
removes the requirement for DM to cover the .1% case.
[How]
- elevate updates during idle optimized state to full updates
- disable idle power optimizations prior to programming
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Setting abm level does not correctly update CRTC state. As a result
no surface update is added to dc stream state and triggers warning.
[How]
Correctly update CRTC state when setting abm level property.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use DCN21 functions instead of DCE110
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Currently navy_flounder is using sienna_cichlid_dmcub.bin.
[How]
Create a seperate define so navy_flounder will use its own firmware.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some monitors could suffer symbol unlock but cannot send HPD IRQ to
notic source device to handle link loss. This makes monitor stuck in
abnormal status and causes black screen.
[How]
According to the suggestion from scalar vendor, to check lane status
again after link training done. That can improve the comaptibility
from current production monitors.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
In dcn3_update_clocks there are situations where dppclk is not
lowered (i.e. stays the same), but DTO still needs to be increased
before we program pipe frontend (i.e. in prepare_bandwidth). If we
don't program the new DTO value before we program the pipe,
we will underflow as soon as the pipe lock is released until the
next call to dcn3_update_clocks where the DTO is updated.
[How]
Remove dppclk check before programming new DTO value.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Fix naming and return bits rather than bytes per pixel for
naming consistency. Because registers return Bytes per pixel,
but DSC Config structure is expecting bits per pixel as input.
So when returning the value convert from bytes into bits.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Struct dcn_dsc_state is used for reading current state
and parameters of DSC on a pipe, the target rate parameter
uses bytes per pixel even though its reading BITS_PER_PIXEL
register.
[How]
Changing it to Bits Per Pixel for consistency.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
This change replaces older looping code in favor of these functions.
[How]
There are built in functions for extracting global sync params
during mode validation now.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
1. allow asic to handle sensor type by itself.
2. if not, use smu common sensor to handle it.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These tables have _COUNT number of elements so the comparisons should be
>= instead of > to prevent reading one element beyond the end of the
array.
Fixes: 8264ee69f0d8 ("drm/amd/powerplay: drop unused code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update sienna_cichlid driver if header and related files.
Support new smu metrics for pre & postDS frequency.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Take back patch:drop unnecessary message support check
Because the gpu reset fail problem on renoir can be fixed by:
drm/amd/powerplay: skip invalid msg when smu set mp1 state
It needs to remove SWSMU_CODE_LAYER_L1 in smu_cmn.h to guard a clear
code layer.
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
jpeg ip block is already selected based on ASIC type during set_ip_blocks.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update golden setting for sienna_cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set valid_in_vf to false for the message not support in vf mode on
sienna cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Mapping Mode1Reset message for sienna_cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some asic may not support for some message of set mp1 state.
If the return value of smu_send_smc_msg is -EINVAL, that means it failed
to send msg to smc as it can not map an valid message for the ASIC. And
with that case, smu_set_mp1_state should be skipped as those ASIC was in
fact do not support for that.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's not necessary to retrieve the power features status when the
asic is booted up the first time. This patch can have the features
enablement status still checked in suspend/resume case and removed
from the first boot up sequence.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The below 3 messages are not supported on Renoir
SMU_MSG_PrepareMp1ForShutdown
SMU_MSG_PrepareMp1ForUnload
SMU_MSG_PrepareMp1ForReset
It needs to revert patch:
drm/amd/powerplay: drop unnecessary message support check
to avoid set mp1 state fail during gpu reset on renoir.
Signed-off-by: changfeng <Changfeng.Zhu@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This will tell users if the faulty page has been written to
external eeprom device in dmesg log.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Added dedicated 64bit reg read/write support
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a spelling mistake in a DRM_ERROR error message. Fix it.
This got lost in a merge, restore the fix.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 4afaa61db9cf5250b5734c2531b226e7b3a3d691)
|
|
[Why]
This was added in the past to solve the issue of not knowing when
to stall for medium and full updates in DM.
Since DC is ultimately decides what requires bandwidth changes we
wanted to make use of it directly to determine this.
The problem is that we can't actually pass any of the stream or surface
updates into DC global validation, so we don't actually check if the new
configuration is valid - we just validate the old existing config
instead and stall for outstanding commits to finish.
There's also the problem of grabbing the DRM private object for
pageflips which can lead to page faults in the case where commits
execute out of order and free a DRM private object state that was
still required for commit tail.
[How]
Now that we reset the plane in DM with the same conditions DC checks
we can have planes go through DC validation and we know when we need
to check and stall based on whether the stream or planes changed.
We mark lock_and_validation_needed whenever we've done this, so just
go back to using that instead of dm_determine_update_type_for_commit.
Since we'll skip resetting the plane for a pageflip we will no longer
grab the DRM private object for pageflips as well, avoiding the
page fault issued caused by pageflipping under load with commits
executing out of order.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
MEDIUM or FULL updates can require global validation or affect
bandwidth. By treating these all simply as surface updates we aren't
actually passing this through DC global validation.
[How]
There's currently no way to pass surface updates through DC global
validation, nor do I think it's a good idea to change the interface
to accept these.
DC global validation itself is currently stateless, and we can move
our update type checking to be stateless as well by duplicating DC
surface checks in DM based on DRM properties.
We wanted to rely on DC automatically determining this since DC knows
best, but DM is ultimately what fills in everything into DC plane
state so it does need to know as well.
There are basically only three paths that we exercise in DM today:
1) Cursor (async update)
2) Pageflip (fast update)
3) Full pipe programming (medium/full updates)
Which means that anything that's more than a pageflip really needs to
go down path #3.
So this change duplicates all the surface update checks based on DRM
state instead inside of should_reset_plane().
Next step is dropping dm_determine_update_type_for_commit and we no
longer require the old DC state at all for global validation.
Optimization can come later so we don't reset DC planes at all for
MEDIUM udpates and avoid validation, but we might require some extra
checks in DM to achieve this.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
So we're not racing with userspace or deadlocking DM.
[How]
These flags are now stored on dm_plane_state itself and acquried and
validated during commit_check, so just use those instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
prepare_planes
[Why]
We're racing with userspace as the flags could potentially change
from when we acquired and validated them in commit_check.
[How]
We unfortunately can't drop this function in its entirety from
prepare_planes since we don't know the afb->address at commit_check
time yet.
So instead of querying new tiling_flags and tmz_surface use the ones
from the plane_state directly.
While we're at it, also update the force_disable_dcc option based
on the state from atomic check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Enabling or disable DCC or switching between tiled and linear formats
can require bandwidth updates.
They're currently skipping all DC validation by being treated as purely
surface updates.
[How]
Treat tiling_flag changes (which encode DCC state) as a condition for
resetting the plane.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Store these in advance so we can reuse them later in commit_tail without
having to reserve the fbo again.
These will also be used for checking for tiling changes when deciding
to reset the plane or not.
[How]
This change should mostly be a refactor. Only commit check is affected
for now and I'll drop the get_fb_info calls in prepare_planes and
commit_tail after.
This runs a prepass loop once we think that all planes have been added
to the context and replaces the get_fb_info calls with accessing the
dm_plane_state instead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update drive if file for sienna_cichlid.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
