| Age | Commit message (Collapse) | Author |
|---|
|
The ath11k active pdevs are protected by RCU but the htt pktlog handling
code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019112521.2071-1-johan+linaro@kernel.org
|
|
The ath11k active pdevs are protected by RCU but the DFS radar event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-3-johan+linaro@kernel.org
|
|
The ath11k active pdevs are protected by RCU but the temperature event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section as reported by RCU lockdep:
=============================
WARNING: suspicious RCU usage
6.6.0-rc6 #7 Not tainted
-----------------------------
drivers/net/wireless/ath/ath11k/mac.c:638 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
...
Call trace:
...
lockdep_rcu_suspicious+0x16c/0x22c
ath11k_mac_get_ar_by_pdev_id+0x194/0x1b0 [ath11k]
ath11k_wmi_tlv_op_rx+0xa84/0x2c1c [ath11k]
ath11k_htc_rx_completion_handler+0x388/0x510 [ath11k]
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: a41d10348b01 ("ath11k: add thermal sensor device support")
Cc: stable@vger.kernel.org # 5.7
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-2-johan+linaro@kernel.org
|
|
In PCI and HAL interface layer module, the identifier sc is used
to represent an instance of ath12k_base structure. However,
within ath12k, the convention is to use "ab" to represent an SoC
"base" struct. So change the all instances of sc to ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231018153008.29820-3-quic_periyasa@quicinc.com
|
|
In WMI layer module, the identifier wmi_sc is used to represent
an instance of ath12k_wmi_base structure. However, within ath12k,
the convention is to use "ab" to represent an SoC "base" struct.
So change the all instances of wmi_sc to wmi_ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231018153008.29820-2-quic_periyasa@quicinc.com
|
|
Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.
The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.
Currently ath11k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath11k driver and provide the amss.bin
firmware data and size to MHI using a pointer.
Currently enum ath11k_fw_features is empty, the patches adding features will
add the flags.
With AHB devices there's no amss.bin or m3.bin, so no changes in how AHB
firmware files are used. But AHB devices can use future additions to the meta
data, for example in enum ath11k_fw_features.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Co-developed-by: Kalle Valo <quic_kvalo@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230727100430.3603551-4-kvalo@kernel.org
|
|
Simple refactoring to make it easier to add firmware-2.bin support in the
following patch.
Earlier ath11k_qmi_m3_load() supported changing m3.bin contents while ath11k is
running. But that's not going to actually work, m3.bin is supposed to be the
same during the lifetime of ath11k, for example we don't support changing the
firmware capabilities on the fly. Due to this ath11k requests m3.bin firmware
file first and only then checks m3_mem->vaddr, so we are basically requesting
the firmware file even if it's not needed. Reverse the code so that m3_mem
buffer is checked first, and only if it doesn't exist, then m3.bin is requested
from user space.
Checking for m3_mem->size is redundant when m3_mem->vaddr is NULL, we would
not be able to use the buffer in that case. So remove the check for size.
Simplify the exit handling and use 'goto out'.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.9
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727100430.3603551-3-kvalo@kernel.org
|
|
Use device_for_each_child_reverse() to find and unregister WMI devices
belonging to a WMI bus device instead of iterating thru the entire
wmi_block_list.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-6-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Since commit fa1f68db6ca7 ("drivers: misc: pass miscdevice pointer via
file private data"), the miscdevice stores a pointer to itself inside
filp->private_data, which means that private_data will not be NULL when
wmi_char_open() is called. This might cause memory corruption should
wmi_char_open() be unable to find its driver, something which can
happen when the associated WMI device is deleted in wmi_free_devices().
Fix the problem by using the miscdevice pointer to retrieve the WMI
device data associated with a char device using container_of(). This
also avoids wmi_char_open() picking a wrong WMI device bound to a
driver with the same name as the original driver.
Fixes: 44b6b7661132 ("platform/x86: wmi: create userspace interface for drivers")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-5-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
When a WMI device besides the first one somehow fails to register,
retval is returned while still containing a negative error code. This
causes the ACPI device fail to probe, leaving behind zombie WMI devices
leading to various errors later.
Handle the single error path separately and return 0 unconditionally
after trying to register all WMI devices to solve the issue. Also
continue to register WMI devices even if some fail to allocate memory.
Fixes: 6ee50aaa9a20 ("platform/x86: wmi: Instantiate all devices before adding them")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-4-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Until now, legacy GUID-based functions where using find_guid() when
searching for WMI devices, which did no refcounting on the returned
WMI device. This meant that the WMI device could disappear at any
moment, potentially leading to various errors. Fix this by using
bus_find_device() which returns an actual reference to the found
WMI device.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-3-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Many aggregate WMI drivers do not use -EPROBE_DEFER when they
cannot find a WMI device during probe, instead they require
all WMI devices associated with an platform device to become
available at once. This is currently achieved by adding those
WMI devices to the wmi_block_list before they are registered,
which is then used by the deprecated GUID-based functions to
search for WMI devices.
Replace this approach with a device link which defers probing
of the WMI device until the associated platform device has finished
probing (and has registered all WMI devices). New aggregate WMI
drivers should not rely on this behaviour.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231020211005.38216-2-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
kfree()/vfree() internally perform NULL check on the
pointer handed to it and take no action if it indeed is
NULL. Hence there is no need for a pre-check of the memory
pointer before handing it to kfree()/vfree().
Issue reported by ifnullfree.cocci Coccinelle semantic
patch script.
Signed-off-by: Bragatheswaran Manickavel <bragathemanick0908@gmail.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the metrics table is marked as io memory, use memcpy_fromio()
when copying its contents.
Compile-tested only.
Fixes: 5150542b8ec5 ("platform/x86/amd/hsmp: add support for metrics tbl")
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20231019135122.21774-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
reported by acpi_video
For a long time now the acpi_video driver reports evdev brightness up/down
key events for the brightness hotkeys on most (non ancient) laptops.
asus-wmi also reports evdev brightness up/down key events for these
keys leading to each press being reported twice and e.g. GNOME increasing
the brightness by 2 steps instead of 1 step.
Use the acpi_video_handles_brightness_key_presses() helper to detect if
acpi_video is reporting brightness key-presses and if it is then don't
report the same events also from the asus-wmi driver.
Note there is a chance that this may lead to regressions where
the brightness hotkeys stop working because they are not actually
reported by the acpi_video driver. Unfortunately the only way to
find out if this is a problem is to try.
To at least avoid regressions on old hw using the eeepc-wmi driver,
implement this as a key filter in asus-nb-wmi so that the eeepc-wmi
driver is not affected.
Reported-by: James John <me@donjajo.com>
Closes: https://lore.kernel.org/platform-driver-x86/a2c441fe-457e-44cf-a146-0ecd86b037cf@donjajo.com/
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231021094841.7419-1-hdegoede@redhat.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
When the MSM8909 SoC is used together with the PM8909 PMIC the primary
power supply for the CPU (VDD_APC) is shared with other components to
the SoC, namely the VDD_CX power domain typically supplied by the PM8909
S1 regulator. This means that all votes for necessary performance states
go via the RPM firmware which collects the requirements from all the
processors in the SoC. The RPM firmware then chooses the actual voltage
based on the performance states ("corners"), depending on calibration
values in the NVMEM and other factors.
The MSM8909 SoC is also sometimes used with the PM8916 or PM660 PMIC.
In that case there is a dedicated regulator connected to VDD_APC and
Linux is responsible to do adaptive voltage scaling using CPR (similar
to the existing code for QCS404).
This difference can be described in the device tree, by either assigning
the CPU a power domain from RPMPD or from the CPR driver.
Describe this using "perf" as generic power domain name, which is also
used already for SCMI based platforms.
Also add a simple function that reads the speedbin from a NVMEM cell
and sets it as-is for opp-supported-hw. The actual bit position can be
described in the device tree without additional driver changes.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[ Viresh: Fixed rebase conflict. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Simplify the allocation and cleanup of driver data by using devm
together with a flexible array. Prepare for adding additional per-CPU
data by defining a struct qcom_cpufreq_drv_cpu instead of storing the
opp_tokens directly.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Now that the driver core allows for struct class to be in read-only
memory, we should make all 'class' structures declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at runtime.
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Link: https://lore.kernel.org/r/2023102403-squirt-defraud-6c0c@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that the driver core allows for struct class to be in read-only
memory, we should make all 'class' structures declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at runtime.
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linuxppc-dev@lists.ozlabs.org
Acked-by: Frederic Barrat <fbarrat@linux.ibm.com>
Link: https://lore.kernel.org/r/2023102434-haiku-uphill-0c11@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When compiling with clang-18, I've noticed the following:
drivers/net/wireless/realtek/rtw89/fw.c:389:28: warning: cast to smaller
integer type 'enum rtw89_fw_type' from 'const void *' [-Wvoid-pointer-to-enum-cast]
389 | enum rtw89_fw_type type = (enum rtw89_fw_type)data;
| ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw89/fw.c:569:13: warning: cast to smaller
integer type 'enum rtw89_rf_path' from 'const void *' [-Wvoid-pointer-to-enum-cast]
569 | rf_path = (enum rtw89_rf_path)data;
| ^~~~~~~~~~~~~~~~~~~~~~~~
So avoid brutal everything-to-const-void-and-back casts, introduce
'union rtw89_fw_element_arg' to pass parameters to element handler
callbacks, and adjust all of the related bits accordingly. Compile
tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231020040940.33154-1-dmantipov@yandex.ru
|
|
Now that the driver core allows for struct class to be in read-only
memory, we should make all 'class' structures declared at build time
placing them into read-only memory, instead of having to be dynamically
allocated at runtime.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/2023102434-font-feast-98e3@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
1. Move MT7620 PA/LNA calibration code to dedicated functions.
2. For external PA/LNA devices, restore RF and BBP registers before
R-Calibration.
3. Do Rx DCOC calibration again before RXIQ calibration.
4. Add some missing LNA related registers' initialization.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315979F92DC563019B8F238BCD4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
1. Move the channel configuration code from rt2800_vco_calibration()
to the rt2800_config_channel().
2. Use MT7620 SoC specific AGC initial LNA value instead of the
RT5592's value.
3. BBP{195,196} pairing write has been replaced with
rt2800_bbp_glrt_write() to reduce redundant code.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315622A4340BFFA530B1B86BCD4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
1. Do not hard reset the BBP. We can use soft reset instead. This
change has some help to the calibration failure issue.
2. Enable falling back to legacy rate from the HT/RTS rate by
setting the HT_FBK_TO_LEGACY register.
3. Implement MCS rate specific maximum PSDU size. It can improve
the transmission quality under the low RSSI condition.
4. Set BBP_84 register value to 0x19. This is used for extension
channel overlapping IOT.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031553CCD4B7A3B89C85935DBCD4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
Add HCLGE_SUPPORT_50G_R1_BIT and HCLGE_SUPPORT_100G_R2_BIT two
capability bits and Corresponding link modes.
Signed-off-by: Hao Chen <chenhao418@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increase name array to be large enough to overcome the following
compilation error.
drivers/infiniband/hw/hfi1/efivar.c: In function ‘read_hfi1_efi_var’:
drivers/infiniband/hw/hfi1/efivar.c:124:44: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
124 | snprintf(name, sizeof(name), "%s-%s", prefix_name, kind);
| ^
drivers/infiniband/hw/hfi1/efivar.c:124:9: note: ‘snprintf’ output 2 or more bytes (assuming 65) into a destination of size 64
124 | snprintf(name, sizeof(name), "%s-%s", prefix_name, kind);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/hfi1/efivar.c:133:52: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
133 | snprintf(name, sizeof(name), "%s-%s", prefix_name, kind);
| ^
drivers/infiniband/hw/hfi1/efivar.c:133:17: note: ‘snprintf’ output 2 or more bytes (assuming 65) into a destination of size 64
133 | snprintf(name, sizeof(name), "%s-%s", prefix_name, kind);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[6]: *** [scripts/Makefile.build:243: drivers/infiniband/hw/hfi1/efivar.o] Error 1
Fixes: c03c08d50b3d ("IB/hfi1: Check upper-case EFI variables")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/238fa39a8fd60e87a5ad7e1ca6584fcdf32e9519.1698159993.git.leonro@nvidia.com
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
handle_receive_interrupt_napi_sp() running inside interrupt handler
could introduce inverse lock ordering between &dd->irq_src_lock
and &dd->uctxt_lock, if read_mod_write() is preempted by the isr.
[CPU0] | [CPU1]
hfi1_ipoib_dev_open() |
--> hfi1_netdev_enable_queues() |
--> enable_queues(rx) |
--> hfi1_rcvctrl() |
--> set_intr_bits() |
--> read_mod_write() |
--> spin_lock(&dd->irq_src_lock) |
| hfi1_poll()
| --> poll_next()
| --> spin_lock_irq(&dd->uctxt_lock)
|
| --> hfi1_rcvctrl()
| --> set_intr_bits()
| --> read_mod_write()
| --> spin_lock(&dd->irq_src_lock)
<interrupt> |
--> handle_receive_interrupt_napi_sp() |
--> set_all_fastpath() |
--> hfi1_rcd_get_by_index() |
--> spin_lock_irqsave(&dd->uctxt_lock) |
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch use spin_lock_irqsave()
on &dd->irq_src_lock inside read_mod_write() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Link: https://lore.kernel.org/r/20230926101116.2797-1-dg573847474@gmail.com
Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add WoL support for KSZ9477 family of switches. This code was tested on
KSZ8563 chip.
KSZ9477 family of switches supports multiple PHY events:
- wake on Link Up
- wake on Energy Detect.
Since current UAPI can't differentiate between this PHY events, map all
of them to WAKE_PHY.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ switches with WoL support signals wake event over PME pin. If this
pin is attached to some external PMIC or System Controller can't be
described as GPIO, the only way to describe it in the devicetree is to
use wakeup-source property. So, add support for this property and enable
PME switch output if this property is present.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the missing offset for the global MAC address register
(REG_SW_MAC_ADDR) for the ksz8863 family of switches.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
utf16s_to_utf8s does not NULL terminate the output string. For us to be
able to add a NULL character when utf16s_to_utf8s returns, we need to make
sure that there is space for such NULL character at the end of the output
buffer. We can achieve this by passing an output buffer size to
utf16s_to_utf8s that is one character less than what we allocated.
Other call sites of utf16s_to_utf8s appear to be using the same technique
where they artificially reduce the buffer size by one to leave space for a
NULL character or line feed character.
Fixes: 4b828fe156a6 ("scsi: ufs: revamp string descriptor reading")
Reviewed-by: Mars Cheng <marscheng@google.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Yen-lin Lai <yenlinlai@google.com>
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Link: https://lore.kernel.org/r/20231017182026.2141163-1-danielmentz@google.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A logical evaluation already results in bool. There is no need for using a
ternary operator based evaluation and bool conversion of the outcome.
Issue identified using boolconv.cocci Coccinelle semantic patch.
Signed-off-by: Bragatheswaran Manickavel <bragathemanick0908@gmail.com>
Link: https://lore.kernel.org/r/20231024183401.48888-1-bragathemanick0908@gmail.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While error handler force complete command (Thread A) and completion IRQ
raising (Thread B) of the same command, it may cause race condition.
Below is racing step (from 1 to 6):
ufshcd_mcq_compl_pending_transfer (Thread A)
1 if (cmd && !test_bit(SCMD_STATE_COMPLETE, &cmd->state)) {
5 spin_lock_irqsave(&hwq->cq_lock, flags); // wait lock release
set_host_byte(cmd, DID_REQUEUE);
6 ufshcd_release_scsi_cmd(hba, lrbp); // access null pointer
scsi_done(cmd);
spin_unlock_irqrestore(&hwq->cq_lock, flags);
}
ufshcd_mcq_poll_cqe_lock (Thread B)
2 spin_lock_irqsave(&hwq->cq_lock, flags);
ufshcd_mcq_poll_cqe_nolock()
ufshcd_compl_one_cqe()
3 ufshcd_release_scsi_cmd() // lrbp->cmd = NULL;
4 spin_unlock_irqrestore(&hwq->cq_lock, flags);
Signed-off-by: Alice Chao <alice.chao@mediatek.com>
Link: https://lore.kernel.org/r/20231024084324.12197-1-alice.chao@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Found by Smatch.
Fixes: 5bcd3bfbda02 ("scsi: megaraid: Pass in NULL scb for host reset")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231023073021.21954-1-hare@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Found by smatch.
Fixes: c67e63800446 ("scsi: aic79xx: Do not reference SCSI command when resetting device")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231023073014.21438-1-hare@suse.de
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Detected by smatch.
Fixes: 17865dc2eccc ("scsi: message: fusion: Open-code mptfc_block_error_handler() for bus reset")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231023073005.20766-1-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The retry loop continues to iterate until the count reaches 30, even after
receiving the correct value. Exit loop when a non-zero value is read.
Fixes: 4ca10f3e3174 ("scsi: mpt3sas: Perform additional retries if doorbell read returns 0")
Cc: stable@vger.kernel.org
Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com>
Link: https://lore.kernel.org/r/20231020105849.6350-1-ranjan.kumar@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return error code directly to save space and be more clear.
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231020023326.43898-1-suhui@nfschina.com
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This is just a cleanup for scsi_dev_queue_ready() to avoid a redundant goto
and if statement. No functional change.
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com>
Link: https://lore.kernel.org/r/20231018113746.1940197-2-haowenchao2@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
pmcraid_eh_target_reset_handler()
When breaking out of an shost_for_each_device() loop one needs to do an
explicit scsi_device_put().
Fixes: c2a14ab3b9b3 ("scsi: pmcraid: Select device in pmcraid_eh_target_reset_handler()")
Signed-off-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/20231023072957.20191-1-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix kernel-doc comment to silence the warnings:
drivers/target/target_core_transport.c:1930: warning: Excess function parameter 'cmd' description in 'target_submit'
drivers/target/target_core_transport.c:1930: warning: Function parameter or member 'se_cmd' not described in 'target_submit'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6844
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231017030913.89973-1-yang.lee@linux.alibaba.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix kernel-doc comment to silence the warnings:
drivers/scsi/pmcraid.c:2697: warning: Excess function parameter 'scsi_cmd' description in 'pmcraid_reset_device'
drivers/scsi/pmcraid.c:2697: warning: Function parameter or member 'scsi_dev' not described in 'pmcraid_reset_device'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=6843
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231017025853.67562-1-yang.lee@linux.alibaba.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.7-2023-10-20:
amdgpu:
- SMU 13 updates
- UMSCH updates
- DC MPO fixes
- RAS updates
- MES 11 fixes
- Fix possible memory leaks in error pathes
- GC 11.5 fixes
- Kernel doc updates
- PSP updates
- APU IMU fixes
- Misc code cleanups
- SMU 11 fixes
- OD fix
- Frame size warning fixes
- SR-IOV fixes
- NBIO 7.11 updates
- NBIO 7.7 updates
- XGMI fixes
- devcoredump updates
amdkfd:
- Misc code cleanups
- SVM fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231020195043.4937-1-alexander.deucher@amd.com
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect new_entry->dbf_name to be NUL-terminated based on its use with
strcmp():
| if (strcmp(entry->dbf_name, name) == 0) {
Moreover, NUL-padding is not required as new_entry is kzalloc'd just
before this assignment:
| new_entry = kzalloc(sizeof(struct qeth_dbf_entry), GFP_KERNEL);
... rendering any future NUL-byte assignments (like the ones strncpy()
does) redundant.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-qeth_core_main-c-v1-1-e7ce65454446@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect chid to be NUL-terminated based on its use with format
strings:
CTCM_DBF_TEXT_(SETUP, CTC_DBF_INFO, "%s(%s) %s", CTCM_FUNTAIL,
chid, ok ? "OK" : "failed");
Moreover, NUL-padding is not required as it is _only_ used in this one
instance with a format string.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
We can also drop the +1 from chid's declaration as we no longer need to
be cautious about leaving a spot for a NUL-byte. Let's use the more
idiomatic strscpy usage of (dest, src, sizeof(dest)) as this more
closely ties the destination buffer to the length.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-ctcm_main-c-v1-1-265db6e78165@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
wo pointer is no longer used in wo_r32 and wo_w32 routines so get rid of
it.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/530537db0872f7523deff21f0a5dfdd9b75fdc9d.1698098459.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The WED mcu firmware does not contain all the memory regions defined in
the dts reserved_memory node (e.g. MT7986 WED firmware does not contain
cpu-boot region).
Reverse the mtk_wed_mcu_run_firmware() logic to check all the fw
sections are defined in the dts reserved_memory node.
Fixes: c6d961aeaa77 ("net: ethernet: mtk_wed: move mem_region array out of mtk_wed_mcu_load_firmware")
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/d983cbfe8ea562fef9264de8f0c501f7d5705bd5.1698098381.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The I40E_TXR_FLAGS_WB_ON_ITR is i40e_ring flag and not i40e_pf one.
Fixes: 8e0764b4d6be42 ("i40e/i40evf: Add support for writeback on ITR feature for X722")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023212714.178032-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mentioning SoCs in Kconfig descriptions tends to get stale (e.g. RAVB is
missing RZV2M) or imprecise (e.g. SH_ETH is not available on all
R8A779x). Drop them instead of providing vague information. Improve the
file description a tad while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20231022205316.3209-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A new Renesas driver shall be added soon. Prepare the Makefile by
grouping the specific objects to the Kconfig symbol for better
readability. Improve the file description a tad while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20231022205316.3209-2-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
