| Age | Commit message (Collapse) | Author |
|---|
|
After fixing mac80211 to allow larger A-MSDUs in some cases, there have been
reports of performance regressions and packet loss with some clients.
It appears that the issue occurs when the hardware is transmitting A-MSDUs
bigger than 8k. Limit the local VHT MPDU size capability to 7991, matching
the value used for MT7915 as well.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200923052442.24141-1-nbd@nbd.name
|
|
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae79b ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe738 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
iProc chips have QSPI controller that does not have the MSPI_REV
offset. Reading from that offset will cause a bus error. Fix it by
having MSPI_REV query disabled in the generic compatible string.
Fixes: 3a01f04d74ef ("spi: bcm-qspi: Handle lack of MSPI_REV offset")
Link: https://lore.kernel.org/linux-arm-kernel/20200909211857.4144718-1-f.fainelli@gmail.com/T/#u
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200910152539.45584-3-ray.jui@broadcom.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A struct device is a dynamic structure, with reference counting.
"Tricking" the kernel to make a dynamic structure static, by working
around the driver core release detection logic, is not nice.
Because of this, this code has been used as an example for others on
"how to do things", which is just about the worst thing possible to have
happen.
Fix this all up by making the platform device dynamic and providing a
real release function.
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Cc: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Rajat Jain <rajatja@google.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Fixes: b02f6a2ef0a1 ("platform/x86: intel_pmc_core: Attach using APCI HID "INT33A1"")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
supply units
Fix topology configuration for power supply units in structure
'mlxplat_mlxcpld_ext_pwr_items_data', due to hardware change.
Note: no need to backport the fix, since there is no such hardware yet
(equipped with four power) at the filed.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
Schematics show that the GPIO number is 55 (not 59). Trivial typo.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When FUJITSU_LAPTOP is enabled and NEW_LEDS is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for LEDS_CLASS
Depends on [n]: NEW_LEDS [=n]
Selected by [y]:
- FUJITSU_LAPTOP [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && INPUT [=y] && BACKLIGHT_CLASS_DEVICE [=y] && (ACPI_VIDEO [=n] || ACPI_VIDEO [=n]=n)
The reason is that FUJITSU_LAPTOP selects LEDS_CLASS without depending on
or selecting NEW_LEDS while LEDS_CLASS is subordinate to NEW_LEDS.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Fixes: d89bcc83e709 ("platform/x86: fujitsu-laptop: select LEDS_CLASS")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When LG_LAPTOP is enabled and NEW_LEDS is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for LEDS_CLASS
Depends on [n]: NEW_LEDS [=n]
Selected by [y]:
- LG_LAPTOP [=y] && X86 [=y] && X86_PLATFORM_DEVICES [=y] && ACPI [=y] && ACPI_WMI [=y] && INPUT [=y]
The reason is that LG_LAPTOP selects LEDS_CLASS without depending on or
selecting NEW_LEDS while LEDS_CLASS is subordinate to NEW_LEDS.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: dbf0c5a6b1f8 ("platform/x86: Add LG Gram laptop special features driver")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
clang static analysis flags this represenative problem
thinkpad_acpi.c:2523:7: warning: Branch condition evaluates
to a garbage value
if (!oldn->mute ||
^~~~~~~~~~~
In hotkey_kthread() mute is conditionally set by hotkey_read_nvram()
but unconditionally checked by hotkey_compare_and_issue_event().
So the tp_nvram_state variable s[2] needs to be initialized.
Fixes: 01e88f25985d ("ACPI: thinkpad-acpi: add CMOS NVRAM polling for hot keys (v9)")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Pavilion 11 x360
Commit cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist
SW_TABLET_MODE on the 9 / "Laptop" chasis-type") restored SW_TABLET_MODE
reporting on the HP stream x360 11 series on which it was previously broken
by commit de9647efeaa9 ("platform/x86: intel-vbtn: Only activate tablet
mode switch on 2-in-1's").
It turns out that enabling SW_TABLET_MODE reporting on devices with a
chassis-type of 10 ("Notebook") causes SW_TABLET_MODE to always report 1
at boot on the HP Pavilion 11 x360, which causes libinput to disable the
kbd and touchpad.
The HP Pavilion 11 x360's ACPI VGBS method sets bit 4 instead of bit 6 when
NOT in tablet mode at boot. Inspecting all the DSDTs in my DSDT collection
shows only one other model, the Medion E1239T ever setting bit 4 and it
always sets this together with bit 6.
So lets treat bit 4 as a second bit which when set indicates the device not
being in tablet-mode, as we already do for bit 6.
While at it also prefix all VGBS constant defines with "VGBS_".
Fixes: cfae58ed681c ("platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The Intel Atom Cherry Trail platform reports a new battery
name (BATC). Tested on ASUS Transformer Mini T103HAF.
Signed-off-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The WMI INIT method on for some reason turns on the camera LED on these
2-in-1s, without the WMI interface allowing further control over the LED.
To fix this commit b5f7311d3a2e ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA") added a blacklist with these 2 models on it
since the WMI driver did not add any extra functionality to these models.
Recently I've been working on making more 2-in-1 models report their
tablet-mode (SW_TABLET_MODE) to userspace; and I've found that these 2
Asus models report this through WMI. This commit reverts the adding
of the blacklist, so that the Asus WMI driver can be used on these
models to report their tablet-mode. I have another patch fixing the LED
issue in a different manner.
Note this is the second time the we revert the adding of the
asus_nb_wmi_blacklist. It was reverted before in commit:
aab9e7896ec9 ("platform/x86: asus-nb-wmi: Revert "Do not load on Asus
T100TA and T200TA")"
But some how (accidentally re-applying of the patch?) it got re-added
again in commit 3bd12da7f50b ("platform/x86: asus-nb-wmi: Do not load
on Asus T100TA and T200TA"), so now we need to revert it again.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Add touchscreen info for the MPMAN Converter9 2-in-1. This device uses the
same case as the ITworks TW891, but it uses a different digitizer, so it
needs its own firmware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Commit 653055b9acd4 ("vhost-vdpa: support get/set backend features")
introduces two malfunction backend features ioctls:
1) the ioctls was blindly added to vring ioctl instead of vdpa device
ioctl
2) vhost_set_backend_features() was called when dev mutex has already
been held which will lead a deadlock
This patch fixes the above issues.
Cc: Eli Cohen <elic@nvidia.com>
Reported-by: Zhu Lingshan <lingshan.zhu@intel.com>
Fixes: 653055b9acd4 ("vhost-vdpa: support get/set backend features")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20200907104343.31141-1-jasowang@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Fix documentation to match actual function prototypes
"end" used instead of "last". Fix that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Link: https://lore.kernel.org/r/20200630052925.GA157062@mtl-vdi-166.wap.labs.mlnx
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When devm_regulator_register() fails, ec should be
freed just like when olpc_ec_cmd() fails.
Fixes: 231c0c216172a ("Platform: OLPC: Add a regulator for the DCON")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
if of_find_device_by_node() succeed, exynos_iommu_of_xlate() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: aa759fd376fb ("iommu/exynos: Add callback for initializing devices from device tree")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200918011335.909141-1-yukuai3@huawei.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
reqcnt is an u32 pointer but we do copy sizeof(reqcnt) which is the
size of the pointer. This means we only copy 8 byte. Let us copy
the full monty.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes: af4a72276d49 ("s390/zcrypt: Support up to 256 crypto adapters.")
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
EEE should be only be enabled during stmmac_mac_link_up() when the
link are up and being set up properly. set_eee should only do settings
configuration and disabling the eee.
Without this fix, turning on EEE using ethtool will return
"Operation not supported". This is due to the driver is in a dead loop
waiting for eee to be advertised in the for eee to be activated but the
driver will only configure the EEE advertisement after the eee is
activated.
Ethtool should only return "Operation not supported" if there is no EEE
capbility in the MAC controller.
Fixes: 8a7493e58ad6 ("net: stmmac: Fix a race in EEE enable callback")
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Acked-by: Mark Gross <mgross@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX DMA channel data is accessed by the xrx200_start_xmit() and the
xrx200_tx_housekeeping() function from different threads. Make sure the
accesses are synchronized by acquiring the netif_tx_lock() in the
xrx200_tx_housekeeping() function too. This lock is acquired by the
kernel before calling xrx200_start_xmit().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 1838d6c62f57836639bd3d83e7855e0ee4f6defc.
This commit moved the ravb_mdio_init() call (and thus the
of_mdiobus_register() call) from the ravb_probe() to the ravb_open()
call. This causes a regression during system resume (s2idle/s2ram), as
new PHY devices cannot be bound while suspended.
During boot, the Micrel PHY is detected like this:
Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Micrel KSZ9031 Gigabit PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=228)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
During system suspend, (A) defer_all_probes is set to true, and (B)
usermodehelper_disabled is set to UMH_DISABLED, to avoid drivers being
probed while suspended.
A. If CONFIG_MODULES=n, phy_device_register() calling device_add()
merely adds the device, but does not probe it yet, as
really_probe() returns early due to defer_all_probes being set:
dpm_resume+0x128/0x4f8
device_resume+0xcc/0x1b0
dpm_run_callback+0x74/0x340
ravb_resume+0x190/0x1b8
ravb_open+0x84/0x770
of_mdiobus_register+0x1e0/0x468
of_mdiobus_register_phy+0x1b8/0x250
of_mdiobus_phy_device_register+0x178/0x1e8
phy_device_register+0x114/0x1b8
device_add+0x3d4/0x798
bus_probe_device+0x98/0xa0
device_initial_probe+0x10/0x18
__device_attach+0xe4/0x140
bus_for_each_drv+0x64/0xc8
__device_attach_driver+0xb8/0xe0
driver_probe_device.part.11+0xc4/0xd8
really_probe+0x32c/0x3b8
Later, phy_attach_direct() notices no PHY driver has been bound,
and falls back to the Generic PHY, leading to degraded operation:
Generic PHY e6800000.ethernet-ffffffff:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e6800000.ethernet-ffffffff:00, irq=POLL)
ravb e6800000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
B. If CONFIG_MODULES=y, request_module() returns early with -EBUSY due
to UMH_DISABLED, and MDIO initialization fails completely:
mdio_bus e6800000.ethernet-ffffffff:00: error -16 loading PHY driver module for ID 0x00221622
ravb e6800000.ethernet eth0: failed to initialize MDIO
PM: dpm_run_callback(): ravb_resume+0x0/0x1b8 returns -16
PM: Device e6800000.ethernet failed to resume: error -16
Ignoring -EBUSY in phy_request_driver_module(), like was done for
-ENOENT in commit 21e194425abd65b5 ("net: phy: fix issue with loading
PHY driver w/o initramfs"), would makes it fall back to the Generic
PHY, like in the CONFIG_MODULES=n case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- DM core fix for incorrect double bio splitting. Keep "fixing" this
because past attempts didn't fully appreciate the liability relative
to recursive bio splitting. This fix limits DM's bio splitting to a
single method and does _not_ use blk_queue_split() for normal IO.
- DM crypt Documentation updates for features added during 5.9 merge.
* tag 'for-5.9/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: document encrypted keyring key option
dm crypt: document new no_workqueue flags
dm: fix comment in dm_process_bio()
dm: fix bio splitting and its bio completion order for regular IO
|
|
In the function nvme_get_effects_log() it uses NVME_NSID_ALL which has
namespace scope. The command effect log page is controller specific.
Replace NVME_NSID_ALL with 0x00 which specifies the controller scope
instead of namespace scope.
Fixes: 84fef62d135b ("nvme: check admin passthru command effects")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209287
Reported-by: Huai-Cheng Kuo <hh81478072@gmail.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
spi_unregister_controller() not only unregisters the controller, but
also frees the controller. This will free the driver data with it, so
we must not access it later dspi_remove().
Solve this by allocating the driver data separately from the SPI
controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20200923131026.20707-1-s.hauer@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently we wrongly set the mask of value of LDO2/4 both to the mask of
LDO2, and the LDO4 voltage configuration is left untouched. This leads
to conflict when LDO2/4 are both in use.
Fix this issue by setting different vsel_mask to both regulators.
Fixes: db4a555f7c4c ("regulator: axp20x: use defines for masks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Link: https://lore.kernel.org/r/20200923005142.147135-1-icenowy@aosc.io
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the lapic_timer_needs_broadcast() stub for
ARCH_APICTIMER_STOPS_ON_C3 unset to actually return
a value.
Fixes: aa6b43d57f99 ("ACPI: processor: Use CPUIDLE_FLAG_TIMER_STOP")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since we store a pointer to the fake iommu device that is allocated on
the stack, as soon as we leave the function it goes out of scope and any
future dereference is undefined behaviour. Just in case we may need to
look at the fake iommu device after initialiation, move the allocation
from the stack into the data.
Fixes: 01b9d4e21148 ("iommu/vt-d: Use dev_iommu_priv_get/set()")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200916105022.28316-2-chris@chris-wilson.co.uk
(cherry picked from commit 9f9f4101fc98db56714e71676d5a1e2d27e01f7e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This error path needs to call clk_disable_unprepare().
Fixes: 7296443b900e ("PM / devfreq: tegra30: Handle possible round-rate error")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The commit 4dc3bab8687f ("PM / devfreq: Add support delayed timer for
polling mode") supports the delayed timer but this commit missed
the adding the timer type to devfreq_summary debugfs node.
Add the timer type to devfreq_summary debugfs.
Fixes: 4dc3bab8687f ("PM / devfreq: Add support delayed timer for polling mode")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.9-rc6:
- Fill asoc card owner in vc4.
- Program secondary CSC correctly in sun4i, and extend
register mapping to cover secondary CSC registers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e3ab56cf-3b8e-9b21-f1b6-9a4989a52996@linux.intel.com
|
|
transport_lookup_tmr_lun() uses "orig_fe_lun" member of struct se_cmd for
the lookup. Hence, update this field directly for the
TARGET_SCF_LOOKUP_LUN_FROM_TAG case.
Link: https://lore.kernel.org/r/1600300471-26135-1-git-send-email-sudhakar.panneerselvam@oracle.com
Fixes: a36840d80027 ("target: Initialize LUN in transport_init_se_cmd()")
Reported-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Sudhakar Panneerselvam <sudhakar.panneerselvam@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
Pull block fixes from Jens Axboe:
"A few NVMe fixes, and a dasd write zero fix"
* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
nvmet: get transport reference for passthru ctrl
nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
nvme-tcp: fix kconfig dependency warning when !CRYPTO
nvme-pci: disable the write zeros command for Intel 600P/P3100
s390/dasd: Fix zero write for FBA devices
|
|
The fixed divider the emac_ptp_free_clk should be 2, not 4.
Fixes: 07afb8db7340 ("clk: socfpga: stratix10: add clock driver for
Stratix10 platform")
Cc: stable@vger.kernel.org
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20200831202657.8224-1-dinguyen@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The ChipID IO region has it's own clock, which is being disabled while
scanning for unused clocks. It turned out that some CPU hotplug, CPU idle
or even SOC firmware code depends on the reads from that area. Fix the
mysterious hang caused by entering deep CPU idle state by ignoring the
'chipid' clock during unused clocks scan, as there are no direct clients
for it which will keep it enabled.
Fixes: e062b571777f ("clk: exynos4: register clocks using common clock framework")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200922124046.10496-1-m.szyprowski@samsung.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-fixes
Pull Tegra clk driver fixes from Thierry Reding:
This is a set of small fixes for the Tegra clock driver.
* tag 'for-5.10-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Fix missing prototype for tegra210_clk_register_emc()
clk: tegra: Always program PLL_E when enabled
clk: tegra: Capitalization fixes
|
|
The commit 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the
idle path"), moved the calls rcu_idle_enter|exit() into the cpuidle core.
However, it forgot to remove a couple of comments in enter_s2idle_proper()
about why RCU_NONIDLE earlier was needed. So, let's drop them as they have
become a bit misleading.
Fixes: 1098582a0f6c ("sched,idle,rcu: Push rcu_idle deeper into the idle path")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2020-09-17
- Fix kernel oops for VFIO edid on BDW (Zhenyu)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917064208.GF11592@zhen-hp.sh.intel.com
|
|
commit 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
adds important bounds checking however it unfortunately also introduces a
bug with respect to section 3.3.1 of the NCM specification.
wDatagramIndex[1] : "Byte index, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramLength[1]: "Byte length, in little endian, of the second datagram
described by this NDP16. If zero, then this marks the end of the sequence
of datagrams in this NDP16."
wDatagramIndex[1] and wDatagramLength[1] respectively then may be zero but
that does not mean we should throw away the data referenced by
wDatagramIndex[0] and wDatagramLength[0] as is currently the case.
Breaking the loop on (index2 == 0 || dg_len2 == 0) should come at the end
as was previously the case and checks for index2 and dg_len2 should be
removed since zero is valid.
I'm not sure how much testing the above patch received but for me right now
after enumeration ping doesn't work. Reverting the commit restores ping,
scp, etc.
The extra validation associated with wDatagramIndex[0] and
wDatagramLength[0] appears to be valid so, this change removes the incorrect
restriction on wDatagramIndex[1] and wDatagramLength[1] restoring data
processing between host and device.
Fixes: 2b74b0a04d3e ("USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()")
Cc: Ilja Van Sprundel <ivansprundel@ioactive.com>
Cc: Brooke Basile <brookebasile@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200920170158.1217068-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lldd may have made calls to delete a remote port or local port and
the delete is in progress when the cli then attempts to create a new
controller. Currently, this proceeds without error although it can't be
very successful.
Fix this by validating that both the host port and remote port are
present when a new controller is to be created.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently, we use nvmeq->q_depth as the upper limit for a valid tag in
nvme_handle_cqe(), it is not correct. Because the available tag number
is recorded in tagset, which is not equal to nvmeq->q_depth.
The nvme driver registers interrupts for queues before initializing the
tagset, because it uses the number of successful request_irq() calls to
configure the tagset parameters. This allows a race condition with the
current tag validity check if the controller happens to produce an
interrupt with a corrupted CQE before the tagset is initialized.
Replace the driver's indirect tag check with the one already provided by
the block layer.
Signed-off-by: Xianting Tian <tian.xianting@h3c.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Initializing the nvme hwmon retrieves a log from the controller. If the
controller is broken, we need to return the appropriate error so that
subsequent initialization doesn't attempt to continue.
Reported-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Andy reported that commit 6b41030fdc79 ("dmaengine: dmatest:
Restore default for channel") broke his scripts for the case
where "busy" channel is used for configuration with expectation
that run command would do nothing. Instead, behavior was
(unintentionally) changed to treat such case as under-configuration
and progress with defaults, i.e. run command would start a test
with default setting for channel (which would use all channels).
Restore original behavior with tracking status of channel setter
so we can distinguish between misconfigured and under-configured
cases in run command and act accordingly.
Fixes: 6b41030fdc79 ("dmaengine: dmatest: Restore default for channel")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200922115847.30100-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Remove superfluous '.c' from qcom-spmi-adc5 device driver name.
Fixes: e13d757279bb ("iio: adc: Add QCOM SPMI PMIC5 ADC driver")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200910140000.324091-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes-2020-09-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
v1->v2:
Remove missing patch from -stable list.
For -stable v5.1
('net/mlx5: Fix FTE cleanup')
For -stable v5.3
('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')
For -stable v5.7
('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')
For -stable v5.8
('net/mlx5e: Use RCU to protect rq->xdp_prog')
('net/mlx5e: Fix endianness when calculating pedit mask first bit')
('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
