| Age | Commit message (Collapse) | Author |
|---|
|
Previously, patches have been added to limit the reported count of SATA
ports for asm1064 and asm1166 SATA controllers, as those controllers do
report more ports than physically having.
While it is allowed to report more ports than physically having in CAP.NP,
it is not allowed to report more ports than physically having in the PI
(Ports Implemented) register, which is what these HBAs do.
(This is a AHCI spec violation.)
Unfortunately, it seems that the PMP implementation in these ASMedia HBAs
is also violating the AHCI and SATA-IO PMP specification.
What these HBAs do is that they do not report that they support PMP
(CAP.SPM (Supports Port Multiplier) is not set).
Instead, they have decided to add extra "virtual" ports in the PI register
that is used if a port multiplier is connected to any of the physical
ports of the HBA.
Enumerating the devices behind the PMP as specified in the AHCI and
SATA-IO specifications, by using PMP READ and PMP WRITE commands to the
physical ports of the HBA is not possible, you have to use the "virtual"
ports.
This is of course bad, because this gives us no way to detect the device
and vendor ID of the PMP actually connected to the HBA, which means that
we can not apply the proper PMP quirks for the PMP that is connected to
the HBA.
Limiting the port map will thus stop these controllers from working with
SATA Port Multipliers.
This patch reverts both patches for asm1064 and asm1166, so old behavior
is restored and SATA PMP will work again, but it will also reintroduce the
(minutes long) extra boot time for the ASMedia controllers that do not
have a PMP connected (either on the PCIe card itself, or an external PMP).
However, a longer boot time for some, is the lesser evil compared to some
other users not being able to detect their drives at all.
Fixes: 0077a504e1a4 ("ahci: asm1166: correct count of reported ports")
Fixes: 9815e3961754 ("ahci: asm1064: correct count of reported ports")
Cc: stable@vger.kernel.org
Reported-by: Matt <cryptearth@googlemail.com>
Signed-off-by: Conrad Kostecki <conikost@gentoo.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[cassel: rewrote commit message]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
The previous commit fixed a bug that led to a NULL peer->device being
dereferenced. It's actually easier and faster performance-wise to
instead get the device from ctx->wg. This semantically makes more sense
too, since ctx->wg->peer_allowedips.seq is compared with
ctx->allowedips_seq, basing them both in ctx. This also acts as a
defence in depth provision against freed peers.
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If all peers are removed via wg_peer_remove_all(), rather than setting
peer_list to empty, the peer is added to a temporary list with a head on
the stack of wg_peer_remove_all(). If a netlink dump is resumed and the
cursored peer is one that has been removed via wg_peer_remove_all(), it
will iterate from that peer and then attempt to dump freed peers.
Fix this by instead checking peer->is_dead, which was explictly created
for this purpose. Also move up the device_update_lock lockdep assertion,
since reading is_dead relies on that.
It can be reproduced by a small script like:
echo "Setting config..."
ip link add dev wg0 type wireguard
wg setconf wg0 /big-config
(
while true; do
echo "Showing config..."
wg showconf wg0 > /dev/null
done
) &
sleep 4
wg setconf wg0 <(printf "[Peer]\nPublicKey=$(wg genkey)\n")
Resulting in:
BUG: KASAN: slab-use-after-free in __lock_acquire+0x182a/0x1b20
Read of size 8 at addr ffff88811956ec70 by task wg/59
CPU: 2 PID: 59 Comm: wg Not tainted 6.8.0-rc2-debug+ #5
Call Trace:
<TASK>
dump_stack_lvl+0x47/0x70
print_address_description.constprop.0+0x2c/0x380
print_report+0xab/0x250
kasan_report+0xba/0xf0
__lock_acquire+0x182a/0x1b20
lock_acquire+0x191/0x4b0
down_read+0x80/0x440
get_peer+0x140/0xcb0
wg_get_device_dump+0x471/0x1130
Cc: stable@vger.kernel.org
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel")
Reported-by: Lillian Berry <lillian@star-ark.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 3e2f544dd8a33 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With commit 34d21de99cea9 ("net: Move {l,t,d}stats allocation to core
and convert veth & vrf"), stats allocation could be done on net core
instead of in this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Remove the allocation in this driver and leverage the network core
allocation instead.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Syzkaller with KCSAN identified a data-race issue when accessing
keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE()
annotations to mark the data race as intentional.
BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll
write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0:
counter_validate drivers/net/wireguard/receive.c:321 [inline]
wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461
__napi_poll+0x60/0x3b0 net/core/dev.c:6536
napi_poll net/core/dev.c:6605 [inline]
net_rx_action+0x32b/0x750 net/core/dev.c:6738
__do_softirq+0xc4/0x279 kernel/softirq.c:553
do_softirq+0x5e/0x90 kernel/softirq.c:454
__local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499
process_one_work kernel/workqueue.c:2633 [inline]
...
read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1:
decrypt_packet drivers/net/wireguard/receive.c:252 [inline]
wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
...
Fixes: a9e90d9931f3 ("wireguard: noise: separate receive counter from send counter")
Reported-by: syzbot+d1de830e4ecdaac83d89@syzkaller.appspotmail.com
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Since free_old_xmit_skbs not only deals with skb, but also xdp frame and
subsequent added xsk, so change the name of this function to
free_old_xmit.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240229072044.77388-19-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
There are two completely similar and independent implementations. This
is inconvenient for the subsequent addition of new types. So extract a
function from this piece of code and call this function uniformly to
recover old xmit ptr.
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240229072044.77388-18-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Adding cond_resched() to the command waiting loop for a better
co-operation with the scheduler. This allows to give CPU a breath to
run other task(workqueue) instead of busy looping when preemption is
not allowed on a device whose CVQ might be slow.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230720083839.481487-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
|
|
This patch convert rx mode setting to be done in a workqueue, this is
a must for allow to sleep when waiting for the cvq command to
response since current code is executed under addr spin lock.
Note that we need to disable and flush the workqueue during freeze,
this means the rx mode setting is lost after resuming. This is not the
bug of this patch as we never try to restore rx mode setting during
resume.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20230720083839.481487-2-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
|
|
When use_dma_api and premapped are true, then the do_unmap is false.
Because the do_unmap is false, vring_unmap_extra_packed is not called by
detach_buf_packed.
if (unlikely(vq->do_unmap)) {
curr = id;
for (i = 0; i < state->num; i++) {
vring_unmap_extra_packed(vq,
&vq->packed.desc_extra[curr]);
curr = vq->packed.desc_extra[curr].next;
}
}
So the indirect desc table is not unmapped. This causes the unmap leak.
So here, we check vq->use_dma_api instead. Synchronously, dma info is
updated based on use_dma_api judgment
This bug does not occur, because no driver use the premapped with
indirect.
Fixes: b319940f83c2 ("virtio_ring: skip unmap for premapped")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Message-Id: <20240223071833.26095-1-xuanzhuo@linux.alibaba.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit reports whether a virtio-blk device
support cache flush command to user space
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-11-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit report read-only information of
virtio-blk devices to user space.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-10-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commits reports write zeroes configuration of
virtio-block devices to user space, includes:
1)maximum write zeroes sectors size
2)maximum write zeroes segment number
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-9-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit reports virtio-blk discarding configuration
to user space,includes:
1) the maximum discard sectors
2) maximum number of discard segments for the block driver to use
3) the alignment for splitting a discarding request
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-8-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit allows vDPA reporting topology information of
virtio-blk devices to user space, includes:
1) the number of logical blocks per physical block
2) offset of first aligned logical block
3) suggested minimum I/O size in blocks
4) optimal (suggested maximum) I/O size in blocks
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-7-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commits allows vDPA reporting virtio-block multi-queue
configuration to user sapce.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-6-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit allows vDPA reporting the maximum number of
segments in a request of virtio-block devices to
user space.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-5-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit allows reporting the block size of a
virtio-block device to user space.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-4-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit allows reporting the max size of any
single segment of virtio-block devices to user space.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-3-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit allows userspace to query capacity of
a virtio-block device.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240218185606.13509-2-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Now that the driver core can properly handle constant struct bus_type,
move the virtio_bus variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Message-Id: <20240204-bus_cleanup-virtio-v1-1-3bcb2212aaa0@marliere.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
Now that the driver core can properly handle constant struct bus_type,
move the vdpa_bus variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Message-Id: <20240204-bus_cleanup-vdpa-v1-1-1745eccb0a5c@marliere.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
IFCVF HW supports operation with vq size less than the max size,
as the spec required.
This commit implements vdpa_config_ops.get_vq_num_min to report
the minimal size of the virtqueues, which gives vDPA framework
a chance to reduce the vring size.
We need at least one descriptor to be functional, but it is better
no less than 64 to meet ceratin performance requirements.
Actually the framework would allocate at least a PAGE for the vq.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-11-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Since we already implemented vdpa_config_ops.get_vq_size,
so get_max_vq_size can return the acutal max size of the
virtqueues other than the max allowed safe size.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-10-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The size of a virtqueue is a per vq configuration,
this commit allows virtio_vdpa to create
virtqueues with the actual size of a specific
vq size that supported by the backend device.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-9-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit implements get_vq_size for vdpa_config_ops. This
new interface is used to report per vq size.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-8-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit implements vdpa_config_ops.get_vq_size for vDPA
simulator, this new interface can help report per vq size.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-7-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit implements get_vq_size which report
per vq size in vdpa_config_ops
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-6-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit implements vdpa_config_ops.get_vq_size in
vp_vdpa, which reports per virtqueue size.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-5-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit implements vdpa_ops.get_vq_size to report
the size of a specific virtqueue.
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-4-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This commit introduces a new interface get_vq_size to
vDPA config ops, this new interface intends to report
the size of a specific virtqueue
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
Message-Id: <20240202163905.8834-3-lingshan.zhu@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This addresses a couple of things found while testing the FLR and AER
handling with the VFs.
- release irqs before calling vp_modern_remove()
- make sure we have a valid struct pointer before using it to release irqs
- make sure the FW is alive before trying to add a new device
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20240220011050.30913-1-shannon.nelson@amd.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Since commit 295525e29a5b ("virtio_net: merge dma
operations when filling mergeable buffers"), VDUSE device
require support for DMA's .sync_single_for_cpu() operation
as the memory is non-coherent between the device and CPU
because of the use of a bounce buffer.
This patch implements both .sync_single_for_cpu() and
.sync_single_for_device() callbacks, and also skip bounce
buffer copies during DMA map and unmap operations if the
DMA_ATTR_SKIP_CPU_SYNC attribute is set to avoid extra
copies of the same buffer.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Message-Id: <20240219170606.587290-1-maxime.coquelin@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The MLX driver was not updating its control virtqueue size at set_vq_num
and instead always initialized to MLX5_CVQ_MAX_ENT (16) at
setup_cvq_vring.
Qemu would try to set the size to 64 by default, however, because the
CVQ size always was initialized to 16, an error would be thrown when
sending >16 control messages (as used-ring entry 17 is initialized to 0).
For example, starting a guest with x-svq=on and then executing the
following command would produce the error below:
# for i in {1..20}; do ifconfig eth0 hw ether XX:xx:XX:xx:XX:XX; done
qemu-system-x86_64: Insufficient written data (0)
[ 435.331223] virtio_net virtio0: Failed to set mac address by vq command.
SIOCSIFHWADDR: Invalid argument
Acked-by: Dragos Tatulea <dtatulea@nvidia.com>
Acked-by: Eugenio Pérez <eperezma@redhat.com>
Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <20240216142502.78095-1-jonah.palmer@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Lei Yang <leiyang@redhat.com>
Fixes: 5262912ef3cf ("vdpa/mlx5: Add support for control VQ and MAC setting")
|
|
If a vdpa device is not in state DRIVER_OK, then there is no driver state
to preserve, so no need to call the suspend and resume driver ops.
Suggested-by: Eugenio Perez Martin <eperezma@redhat.com>"
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Message-Id: <1707834358-165470-1-git-send-email-steven.sistare@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
|
|
Currently, we don't reenable the config if freezing the device failed.
For example, virtio-mem currently doesn't support suspend+resume, and
trying to freeze the device will always fail. Afterwards, the device
will no longer respond to resize requests, because it won't get notified
about config changes.
Let's fix this by re-enabling the config if freezing fails.
Fixes: 22b7050a024d ("virtio: defer config changed notifications")
Cc: <stable@kernel.org>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20240213135425.795001-1-david@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
vdpasim_do_reset sets running to true, which is wrong, as it allows
vdpasim_kick_vq to post work requests before the device has been
configured. To fix, do not set running until VIRTIO_CONFIG_S_DRIVER_OK
is set.
Fixes: 0c89e2a3a9d0 ("vdpa_sim: Implement suspend vdpa op")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Reviewed-by: Eugenio Pérez <eperezma@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1707517807-137331-1-git-send-email-steven.sistare@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When the Qemu launched with vhost but without tap vnet_hdr,
vhost tries to copy vnet_hdr from socket iter with size 0
to the page that may contain some trash.
That trash can be interpreted as unpredictable values for
vnet_hdr.
That leads to dropping some packets and in some cases to
stalling vhost routine when the vhost_net tries to process
packets and fails in a loop.
Qemu options:
-netdev tap,vhost=on,vnet_hdr=off,...
Signed-off-by: Andrew Melnychenko <andrew@daynix.com>
Message-Id: <20240115194840.1183077-1-andrew@daynix.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
https://gitlab.freedesktop.org/drm/misc/kernel into drm-next
Short summary of fixes pull:
probe-helper:
- never return negative values from .get_modes() plus driver fixes
nouveau:
- clear bo resource bus after eviction
- documentation fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240314082833.GA8761@localhost.localdomain
|
|
duplicated code in redo_fd_request(),
unlock_fdc() function has the same code "do_floppy = NULL" inside.
Signed-off-by: Yufeng Wang <wangyufeng@kylinos.cn>
Suggested-by: Denis Efremov <efremov@linux.com>
Link: https://lore.kernel.org/r/20240319014219.7812-1-wangyufeng@kylinos.cn
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next
Driver changes:
- Invalidate userptr VMA on page pin fault, allowing userspace
to free userptr while still having bindings
- Fail early on sysfs file creation error
- Skip VMA pinning on xe_exec with num_batch_buffer == 0
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c4epi2j6anpc77z73zbgibxg7bxsmmkb522aa7tyei6oa6uunn@3oad4cgomd5a
|
|
Pull rdma updates from Jason Gunthorpe:
"Very small update this cycle:
- Minor code improvements in fi, rxe, ipoib, mana, cxgb4, mlx5,
irdma, rxe, rtrs, mana
- Simplify the hns hem mechanism
- Fix EFA's MSI-X allocation in resource constrained configurations
- Fix a KASN splat in srpt
- Narrow hns's congestion control selection to QPs granularity and
allow userspace to select it
- Solve a parallel module loading race between the CM module and a
driver module
- Flexible array cleanup
- Dump hns's SCC Conext to 'rdma res' for debugging
- Make mana build page lists for HW objects that require a 0 offset
correctly
- Stuck CM ID debugging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (29 commits)
RDMA/cm: add timeout to cm_destroy_id wait
RDMA/mana_ib: Use virtual address in dma regions for MRs
RDMA/mana_ib: Fix bug in creation of dma regions
RDMA/hns: Append SCC context to the raw dump of QPC
RDMA/uverbs: Avoid -Wflex-array-member-not-at-end warnings
RDMA/hns: Support userspace configuring congestion control algorithm with QP granularity
RDMA/rtrs-clt: Check strnlen return len in sysfs mpath_policy_store()
RDMA/uverbs: Remove flexible arrays from struct *_filter
RDMA/device: Fix a race between mad_client and cm_client init
RDMA/hns: Fix mis-modifying default congestion control algorithm
RDMA/rxe: Remove unused 'iova' parameter from rxe_mr_init_user
RDMA/srpt: Do not register event handler until srpt device is fully setup
RDMA/irdma: Remove duplicate assignment
RDMA/efa: Limit EQs to available MSI-X vectors
RDMA/mlx5: Delete unused mlx5_ib_copy_pas prototype
RDMA/cxgb4: Delete unused c4iw_ep_redirect prototype
RDMA/mana_ib: Introduce mana_ib_install_cq_cb helper function
RDMA/mana_ib: Introduce mana_ib_get_netdev helper function
RDMA/mana_ib: Introduce mdev_to_gc helper function
RDMA/hns: Simplify 'struct hns_roce_hem' allocation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing updates from Steven Rostedt:
"Main user visible change:
- User events can now have "multi formats"
The current user events have a single format. If another event is
created with a different format, it will fail to be created. That
is, once an event name is used, it cannot be used again with a
different format. This can cause issues if a library is using an
event and updates its format. An application using the older format
will prevent an application using the new library from registering
its event.
A task could also DOS another application if it knows the event
names, and it creates events with different formats.
The multi-format event is in a different name space from the single
format. Both the event name and its format are the unique
identifier. This will allow two different applications to use the
same user event name but with different payloads.
- Added support to have ftrace_dump_on_oops dump out instances and
not just the main top level tracing buffer.
Other changes:
- Add eventfs_root_inode
Only the root inode has a dentry that is static (never goes away)
and stores it upon creation. There's no reason that the thousands
of other eventfs inodes should have a pointer that never gets set
in its descriptor. Create a eventfs_root_inode desciptor that has a
eventfs_inode descriptor and a dentry pointer, and only the root
inode will use this.
- Added WARN_ON()s in eventfs
There's some conditionals remaining in eventfs that should never be
hit, but instead of removing them, add WARN_ON() around them to
make sure that they are never hit.
- Have saved_cmdlines allocation also include the map_cmdline_to_pid
array
The saved_cmdlines structure allocates a large amount of data to
hold its mappings. Within it, it has three arrays. Two are already
apart of it: map_pid_to_cmdline[] and saved_cmdlines[]. More memory
can be saved by also including the map_cmdline_to_pid[] array as
well.
- Restructure __string() and __assign_str() macros used in
TRACE_EVENT()
Dynamic strings in TRACE_EVENT() are declared with:
__string(name, source)
And assigned with:
__assign_str(name, source)
In the tracepoint callback of the event, the __string() is used to
get the size needed to allocate on the ring buffer and
__assign_str() is used to copy the string into the ring buffer.
There's a helper structure that is created in the TRACE_EVENT()
macro logic that will hold the string length and its position in
the ring buffer which is created by __string().
There are several trace events that have a function to create the
string to save. This function is executed twice. Once for
__string() and again for __assign_str(). There's no reason for
this. The helper structure could also save the string it used in
__string() and simply copy that into __assign_str() (it also
already has its length).
By using the structure to store the source string for the
assignment, it means that the second argument to __assign_str() is
no longer needed.
It will be removed in the next merge window, but for now add a
warning if the source string given to __string() is different than
the source string given to __assign_str(), as the source to
__assign_str() isn't even used and will be going away.
- Added checks to make sure that the source of __string() is also the
source of __assign_str() so that it can be safely removed in the
next merge window.
Included fixes that the above check found.
- Other minor clean ups and fixes"
* tag 'trace-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace: (34 commits)
tracing: Add __string_src() helper to help compilers not to get confused
tracing: Use strcmp() in __assign_str() WARN_ON() check
tracepoints: Use WARN() and not WARN_ON() for warnings
tracing: Use div64_u64() instead of do_div()
tracing: Support to dump instance traces by ftrace_dump_on_oops
tracing: Remove second parameter to __assign_rel_str()
tracing: Add warning if string in __assign_str() does not match __string()
tracing: Add __string_len() example
tracing: Remove __assign_str_len()
ftrace: Fix most kernel-doc warnings
tracing: Decrement the snapshot if the snapshot trigger fails to register
tracing: Fix snapshot counter going between two tracers that use it
tracing: Use EVENT_NULL_STR macro instead of open coding "(null)"
tracing: Use ? : shortcut in trace macros
tracing: Do not calculate strlen() twice for __string() fields
tracing: Rework __assign_str() and __string() to not duplicate getting the string
cxl/trace: Properly initialize cxl_poison region name
net: hns3: tracing: fix hclgevf trace event strings
drm/i915: Add missing ; to __assign_str() macros in tracepoint code
NFSD: Fix nfsd_clid_class use of __string_len() macro
...
|
|
A Hyper-V host provides its guest VMs with entropy in a custom ACPI
table named "OEM0". The entropy bits are updated each time Hyper-V
boots the VM, and are suitable for seeding the Linux guest random
number generator (rng). See a brief description of OEM0 in [1].
Generation 2 VMs on Hyper-V use UEFI to boot. Existing EFI code in
Linux seeds the rng with entropy bits from the EFI_RNG_PROTOCOL.
Via this path, the rng is seeded very early during boot with good
entropy. The ACPI OEM0 table provided in such VMs is an additional
source of entropy.
Generation 1 VMs on Hyper-V boot from BIOS. For these VMs, Linux
doesn't currently get any entropy from the Hyper-V host. While this
is not fundamentally broken because Linux can generate its own entropy,
using the Hyper-V host provided entropy would get the rng off to a
better start and would do so earlier in the boot process.
Improve the rng seeding for Generation 1 VMs by having Hyper-V specific
code in Linux take advantage of the OEM0 table to seed the rng. For
Generation 2 VMs, use the OEM0 table to provide additional entropy
beyond the EFI_RNG_PROTOCOL. Because the OEM0 table is custom to
Hyper-V, parse it directly in the Hyper-V code in the Linux kernel
and use add_bootloader_randomness() to add it to the rng. Once the
entropy bits are read from OEM0, zero them out in the table so
they don't appear in /sys/firmware/acpi/tables/OEM0 in the running
VM. The zero'ing is done out of an abundance of caution to avoid
potential security risks to the rng. Also set the OEM0 data length
to zero so a kexec or other subsequent use of the table won't try
to use the zero'ed bits.
[1] https://download.microsoft.com/download/1/c/9/1c9813b8-089c-4fef-b2ad-ad80e79403ba/Whitepaper%20-%20The%20Windows%2010%20random%20number%20generation%20infrastructure.pdf
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20240318155408.216851-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240318155408.216851-1-mhklinux@outlook.com>
|
|
c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
corrects three cases of setting the ECSPI burst length but erroneously
leaves the in-range CPU case one bit to big (in that field a value of
0 means 1 bit). The effect was that transmissions that should have been
8-bit bytes appeared as 9-bit causing failed communication with SPI
devices.
Link: https://lore.kernel.org/all/20240201105451.507005-1-carlos.song@nxp.com/
Link: https://lore.kernel.org/all/20240204091912.36488-1-carlos.song@nxp.com/
Fixes: c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
Signed-off-by: Adam Butcher <adam@jessamine.co.uk>
Link: https://msgid.link/r/20240318175119.3334-1-adam@jessamine.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The default nvme_tcp_wq will use all CPUs to process tasks. Sometimes it is
necessary to set CPU affinity to improve performance.
A new module parameter wq_unbound is added here. If set to true, users can
configure cpu affinity through
/sys/devices/virtual/workqueue/nvme_tcp_wq/cpumask.
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Make the workqueue userspace visible for easy viewing and configuration.
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
This commit adds NVME_QUIRK_NO_DEEPEST_PS and NVME_QUIRK_BOGUS_NID for
device [126f:2262], which appears to be a generic VID:PID pair used for
many SSDs based on the Silicon Motion SM2262/SM2262EN controller.
Two of my SSDs with this VID:PID pair exhibit the same behavior:
* They frequently have trouble exiting the deepest power state (5),
resulting in the entire disk unresponsive.
Verified by setting nvme_core.default_ps_max_latency_us=10000 and
observing them behaving normally.
* They produce all-zero nguid and eui64 with `nvme id-ns` command.
The offending products are:
* HP SSD EX950 1TB
* HIKVISION C2000Pro 2TB
Signed-off-by: Jiawei Fu <i@ibugone.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
As per the hardware team, TIEN and TINT source should not set at the same
time due to a possible hardware race leading to spurious IRQ.
Currently on some scenarios hardware settings for TINT detection is not in
sync with TINT source as the enable/disable overrides source setting value
leading to hardware inconsistent state. For eg: consider the case GPIOINT0
is used as TINT interrupt and configuring GPIOINT5 as edge type. During
rzg2l_irq_set_type(), TINT source for GPIOINT5 is set. On disable(),
clearing of the entire bytes of TINT source selection for GPIOINT5 is same
as GPIOINT0 with TIEN disabled. Apart from this during enable(), the
setting of GPIOINT5 with TIEN results in spurious IRQ as due to a HW race,
it is possible that IP can use the TIEN with previous source value
(GPIOINT0).
So, just update TIEN during enable/disable as TINT source is already set
during rzg2l_irq_set_type(). This will make the consistent hardware
settings for detection method tied with TINT source and allows to simplify
the code.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
