| Age | Commit message (Collapse) | Author |
|---|
|
of_irq_parse_one() may use uninitialized variable @addr_len as shown below:
// @addr_len is uninitialized
int addr_len;
// This operation does not touch @addr_len if it fails.
addr = of_get_property(device, "reg", &addr_len);
// Use uninitialized @addr_len if the operation fails.
if (addr_len > sizeof(addr_buf))
addr_len = sizeof(addr_buf);
// Check the operation result here.
if (addr)
memcpy(addr_buf, addr, addr_len);
Fix by initializing @addr_len before the operation.
Fixes: b739dffa5d57 ("of/irq: Prevent device address out-of-bounds read in interrupt map walk")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241209-of_irq_fix-v1-4-782f1419c8a1@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
On a malformed interrupt-map property which is shorter than expected by
1 cell, we may read bogus data past the end of the property instead of
returning an error in of_irq_parse_imap_parent().
Decrement the remaining length when skipping over the interrupt parent
phandle cell.
Fixes: 935df1bd40d4 ("of/irq: Factor out parsing of interrupt-map parent phandle+args from of_irq_parse_raw()")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241209-of_irq_fix-v1-1-782f1419c8a1@quicinc.com
[rh: reword commit msg]
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
__of_get_dma_parent() returns OF device node @args.np, but the node's
refcount is increased twice, by both of_parse_phandle_with_args() and
of_node_get(), so causes refcount leakage for the node.
Fix by directly returning the node got by of_parse_phandle_with_args().
Fixes: f83a6e5dea6c ("of: address: Add support for the parent DMA bus")
Cc: stable@vger.kernel.org
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Link: https://lore.kernel.org/r/20241206-of_core_fix-v1-4-dc28ed56bec3@quicinc.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
|
|
commit 18d9b5227121 ("cpufreq/amd-pstate: Use nominal perf for limits
when boost is disabled") introduced different semantics for min/max limits
based upon whether the user turned off boost from sysfs.
This however is not necessary when the highest perf value is the boost
numerator.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Fixes: 18d9b5227121 ("cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled")
Link: https://lore.kernel.org/r/20241209185248.16301-3-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
commit ad4caad58d91d ("cpufreq: amd-pstate: Merge
amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
changed the semantics for highest perf and commit 18d9b52271213
("cpufreq/amd-pstate: Use nominal perf for limits when boost is disabled")
worked around those semantic changes.
This however is a confusing result and furthermore makes it awkward to
change frequency limits and boost due to the scaling differences. Restore
the boost numerator to highest perf again.
Suggested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Reviewed-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Fixes: ad4caad58d91 ("cpufreq: amd-pstate: Merge amd_pstate_highest_perf_set() into amd_get_boost_ratio_numerator()")
Link: https://lore.kernel.org/r/20241209185248.16301-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
The zone reclaim processing of the dm-zoned device mapper uses
blkdev_issue_zeroout() to align the write pointer of a zone being used
for reclaiming another zone, to write the valid data blocks from the
zone being reclaimed at the same position relative to the zone start in
the reclaim target zone.
The first call to blkdev_issue_zeroout() will try to use hardware
offload using a REQ_OP_WRITE_ZEROES operation if the device reports a
non-zero max_write_zeroes_sectors queue limit. If this operation fails
because of the lack of hardware support, blkdev_issue_zeroout() falls
back to using a regular write operation with the zero-page as buffer.
Currently, such REQ_OP_WRITE_ZEROES failure is automatically handled by
the block layer zone write plugging code which will execute a report
zones operation to ensure that the write pointer of the target zone of
the failed operation has not changed and to "rewind" the zone write
pointer offset of the target zone as it was advanced when the write zero
operation was submitted. So the REQ_OP_WRITE_ZEROES failure does not
cause any issue and blkdev_issue_zeroout() works as expected.
However, since the automatic recovery of zone write pointers by the zone
write plugging code can potentially cause deadlocks with queue freeze
operations, a different recovery must be implemented in preparation for
the removal of zone write plugging report zones based recovery.
Do this by introducing the new function blk_zone_issue_zeroout(). This
function first calls blkdev_issue_zeroout() with the flag
BLKDEV_ZERO_NOFALLBACK to intercept failures on the first execution
which attempt to use the device hardware offload with the
REQ_OP_WRITE_ZEROES operation. If this attempt fails, a report zone
operation is issued to restore the zone write pointer offset of the
target zone to the correct position and blkdev_issue_zeroout() is called
again without the BLKDEV_ZERO_NOFALLBACK flag. The report zones
operation performing this recovery is implemented using the helper
function disk_zone_sync_wp_offset() which calls the gendisk report_zones
file operation with the callback disk_report_zones_cb(). This callback
updates the target write pointer offset of the target zone using the new
function disk_zone_wplug_sync_wp_offset().
dmz_reclaim_align_wp() is modified to change its call to
blkdev_issue_zeroout() to a call to blk_zone_issue_zeroout() without any
other change needed as the two functions are functionnally equivalent.
Fixes: dd291d77cc90 ("block: Introduce zone write plugging")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Mike Snitzer <snitzer@kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20241209122357.47838-4-dlemoal@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When using MES creating a pdd will require talking to the GPU to
setup the relevant context. The code here forgot to wake up the GPU
in case it was in suspend, this causes KVM to EFAULT for passthrough
GPU for example. This issue can be masked if the GPU was woken up by
other things (e.g. opening the KMS node) first and have not yet gone to sleep.
v4: do the allocation of proc_ctx_bo in a lazy fashion
when the first queue is created in a process (Felix)
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Reviewed-by: Yunxiang Li <Yunxiang.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Emitting the cleaner shader must come after the check if a VM switch is
necessary or not.
Otherwise we will emit the cleaner shader every time and not just when it is
necessary because we switched between applications.
This can otherwise crash on gang submit and probably decreases performance
quite a bit.
v2: squash in fix from Srini (Alex)
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: ee7a846ea27b ("drm/amdgpu: Emit cleaner shader at end of IB submission")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
ISP hw_init is not called with the recent changes related
to hw init levels. AMDGPU_INIT_LEVEL_DEFAULT is ignoring
the ISP IP block as AMDGPU_IP_BLK_MASK_ALL is derived using
incorrect max number of IP blocks.
Update AMDGPU_IP_BLK_MASK_ALL to use AMD_IP_BLOCK_TYPE_NUM
instead of AMDGPU_MAX_IP_NUM to fix the issue.
Fixes: 14f2fe34f5c6 ("drm/amdgpu: Add init levels")
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Pratap Nirujogi <pratap.nirujogi@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This information is not available in ip discovery table.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: David Belanger <david.belanger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This information is not available in ip discovery table.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: David Belanger <david.belanger@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
In the function pqm_uninit there is a call-assignment of "pdd =
kfd_get_process_device_data" which could be null, and this value was
later dereferenced without checking.
Fixes: fb91065851cd ("drm/amdkfd: Refactor queue wptr_bo GART mapping")
Signed-off-by: Andrew Martin <Andrew.Martin@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The OF match table is not NULL-terminated.
Fix this by adding a sentinel to nmk_i2c_eyeq_match_table[].
Fixes: a0d15cc47f29be6d ("i2c: nomadik: switch from of_device_is_compatible() to of_match_device()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Théo Lebrun <theo.lebrun@bootlin.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Current implementation leaves pdev->dev as a wakeup source. Add a
device_init_wakeup(&pdev->dev, false) call in the .remove() function and
in the error path of the .probe() function.
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Fixes: 527f36f5efa4 ("mmc: mediatek: add support for SDIO eint wakup IRQ")
Cc: stable@vger.kernel.org
Message-ID: <20241203023442.2434018-1-joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Value 0 in ADMA length descriptor is interpreted as 65536 on new Tegra
chips, remove SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC quirk to make sure max
ADMA2 length is 65536.
Fixes: 4346b7c7941d ("mmc: tegra: Add Tegra186 support")
Cc: stable@vger.kernel.org
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241209101009.22710-1-pshete@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since commit f63b94be6942 ("i2c: pnx: Fix potential deadlock warning
from del_timer_sync() call in isr") jiffies are stored in
i2c_pnx_algo_data.timeout, but wait_timeout and wait_reset are still
using it as milliseconds. Convert jiffies back to milliseconds to wait
for the expected amount of time.
Fixes: f63b94be6942 ("i2c: pnx: Fix potential deadlock warning from del_timer_sync() call in isr")
Signed-off-by: Vladimir Riabchun <ferr.lambarginio@gmail.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
When drivers access P2SB device resources, it calls p2sb_bar(). Before
the commit 5913320eb0b3 ("platform/x86: p2sb: Allow p2sb_bar() calls
during PCI device probe"), p2sb_bar() obtained the resources and then
called pci_stop_and_remove_bus_device() for clean up. Then the P2SB
device disappeared. The commit 5913320eb0b3 introduced the P2SB device
resource cache feature in the boot process. During the resource cache,
pci_stop_and_remove_bus_device() is called for the P2SB device, then the
P2SB device disappears regardless of whether p2sb_bar() is called or
not. Such P2SB device disappearance caused a confusion [1]. To avoid the
confusion, avoid the pci_stop_and_remove_bus_device() call when the BIOS
does not hide the P2SB device.
For that purpose, cache the P2SB device resources only if the BIOS hides
the P2SB device. Call p2sb_scan_and_cache() only if p2sb_hidden_by_bios
is true. This allows removing two branches from p2sb_scan_and_cache().
When p2sb_bar() is called, get the resources from the cache if the P2SB
device is hidden. Otherwise, read the resources from the unhidden P2SB
device.
Reported-by: Daniel Walker (danielwa) <danielwa@cisco.com>
Closes: https://lore.kernel.org/lkml/ZzTI+biIUTvFT6NC@goliath/ [1]
Fixes: 5913320eb0b3 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241128002836.373745-5-shinichiro.kawasaki@wdc.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
To prepare for the following fix, move the code to hide and unhide the
P2SB device from p2sb_cache_resources() to p2sb_scan_and_cache().
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241128002836.373745-4-shinichiro.kawasaki@wdc.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
To prepare for the following fix, introduce the global flag
p2sb_hidden_by_bios. Check if the BIOS hides the P2SB device and store
the result in the flag. This allows to refer to the check result across
functions.
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241128002836.373745-3-shinichiro.kawasaki@wdc.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
To prepare for the following fix, factor out the code to read the P2SB
resource from the cache to the new function p2sb_read_from_cache().
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20241128002836.373745-2-shinichiro.kawasaki@wdc.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Adds support to Alienware m16 R1 AMD.
Tested-by: Cihan Ozakca <cozakca@outlook.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20241208003013.6490-3-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Devices that are known to support the WMI thermal interface do not
support the legacy LED control interface. Make `.num_zones = 0` and
avoid calling alienware_zone_init() if that's the case.
Fixes: 9f6c43041552 ("alienware-wmi: added platform profile support")
Fixes: 1c1eb70e7d23 ("alienware-wmi: extends the list of supported models")
Suggested-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20241208002652.5885-4-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
DEFAULT_SYMBOL_NAMESPACE must already be defined when <linux/export.h>
is included. So move the define above the include block.
Fixes: b9b1fc1ae119 ("gpio: idio-16: Introduce the ACCES IDIO-16 GPIO library module")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: William Breathitt Gray <wbg@kernel.org>
Link: https://lore.kernel.org/r/20241203172631.1647792-2-u.kleine-koenig@baylibre.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Linux 6.13-rc2
|
|
virtnet_sq_bind_xsk_pool() flushes tx skbs and then resets tx queue, so
DQL counters need to be reset when flushing has actually occurred, Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_resize()
to handle this.
Fixes: 21a4e3ce6dc7 ("virtio_net: xsk: bind/unbind xsk for tx")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_reset() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when it really occurs.
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
virtnet_tx_resize() flushes remaining tx skbs, requiring DQL counters to
be reset when flushing has actually occurred. Add
virtnet_sq_free_unused_buf_done() as a callback for virtqueue_reset() to
handle this.
Fixes: c8bd1f7f3e61 ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtqueue_resize() has actually recycled all unused buffers,
additional work may be required in some cases. Relying solely on its
return status is fragile, so introduce a new function argument
'recycle_done', which is invoked when the recycle really occurs.
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While not harmful, using vq2rxq where it's always sq appears odd.
Replace it with the more appropriate vq2txq for clarity and correctness.
Fixes: 89f86675cb03 ("virtio_net: xsk: tx: support xmit xsk buffer")
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When virtnet_close is followed by virtnet_open, some TX completions can
possibly remain unconsumed, until they are finally processed during the
first NAPI poll after the netdev_tx_reset_queue(), resulting in a crash
[1]. Commit b96ed2c97c79 ("virtio_net: move netdev_tx_reset_queue() call
before RX napi enable") was not sufficient to eliminate all BQL crash
cases for virtio-net.
This issue can be reproduced with the latest net-next master by running:
`while :; do ip l set DEV down; ip l set DEV up; done` under heavy network
TX load from inside the machine.
netdev_tx_reset_queue() can actually be dropped from virtnet_open path;
the device is not stopped in any case. For BQL core part, it's just like
traffic nearly ceases to exist for some period. For stall detector added
to BQL, even if virtnet_close could somehow lead to some TX completions
delayed for long, followed by virtnet_open, we can just take it as stall
as mentioned in commit 6025b9135f7a ("net: dqs: add NIC stall detector
based on BQL"). Note also that users can still reset stall_max via sysfs.
So, drop netdev_tx_reset_queue() from virtnet_enable_queue_pair(). This
eliminates the BQL crashes. As a result, netdev_tx_reset_queue() is now
explicitly required in freeze/restore path. This patch adds it to
immediately after free_unused_bufs(), following the rule of thumb:
netdev_tx_reset_queue() should follow any SKB freeing not followed by
netdev_tx_completed_queue(). This seems the most consistent and
streamlined approach, and now netdev_tx_reset_queue() runs whenever
free_unused_bufs() is done.
[1]:
------------[ cut here ]------------
kernel BUG at lib/dynamic_queue_limits.c:99!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 7 UID: 0 PID: 1598 Comm: ip Tainted: G N 6.12.0net-next_main+ #2
Tainted: [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), \
BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:dql_completed+0x26b/0x290
Code: b7 c2 49 89 e9 44 89 da 89 c6 4c 89 d7 e8 ed 17 47 00 58 65 ff 0d
4d 27 90 7e 0f 85 fd fe ff ff e8 ea 53 8d ff e9 f3 fe ff ff <0f> 0b 01
d2 44 89 d1 29 d1 ba 00 00 00 00 0f 48 ca e9 28 ff ff ff
RSP: 0018:ffffc900002b0d08 EFLAGS: 00010297
RAX: 0000000000000000 RBX: ffff888102398c80 RCX: 0000000080190009
RDX: 0000000000000000 RSI: 000000000000006a RDI: 0000000000000000
RBP: ffff888102398c00 R08: 0000000000000000 R09: 0000000000000000
R10: 00000000000000ca R11: 0000000000015681 R12: 0000000000000001
R13: ffffc900002b0d68 R14: ffff88811115e000 R15: ffff8881107aca40
FS: 00007f41ded69500(0000) GS:ffff888667dc0000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000556ccc2dc1a0 CR3: 0000000104fd8003 CR4: 0000000000772ef0
PKRU: 55555554
Call Trace:
<IRQ>
? die+0x32/0x80
? do_trap+0xd9/0x100
? dql_completed+0x26b/0x290
? dql_completed+0x26b/0x290
? do_error_trap+0x6d/0xb0
? dql_completed+0x26b/0x290
? exc_invalid_op+0x4c/0x60
? dql_completed+0x26b/0x290
? asm_exc_invalid_op+0x16/0x20
? dql_completed+0x26b/0x290
__free_old_xmit+0xff/0x170 [virtio_net]
free_old_xmit+0x54/0xc0 [virtio_net]
virtnet_poll+0xf4/0xe30 [virtio_net]
? __update_load_avg_cfs_rq+0x264/0x2d0
? update_curr+0x35/0x260
? reweight_entity+0x1be/0x260
__napi_poll.constprop.0+0x28/0x1c0
net_rx_action+0x329/0x420
? enqueue_hrtimer+0x35/0x90
? trace_hardirqs_on+0x1d/0x80
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? kvm_sched_clock_read+0xd/0x20
? sched_clock+0xc/0x30
? sched_clock_cpu+0xd/0x1a0
handle_softirqs+0x138/0x3e0
do_softirq.part.0+0x89/0xc0
</IRQ>
<TASK>
__local_bh_enable_ip+0xa7/0xb0
virtnet_open+0xc8/0x310 [virtio_net]
__dev_open+0xfa/0x1b0
__dev_change_flags+0x1de/0x250
dev_change_flags+0x22/0x60
do_setlink.isra.0+0x2df/0x10b0
? rtnetlink_rcv_msg+0x34f/0x3f0
? netlink_rcv_skb+0x54/0x100
? netlink_unicast+0x23e/0x390
? netlink_sendmsg+0x21e/0x490
? ____sys_sendmsg+0x31b/0x350
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? __nla_validate_parse+0x5f/0xee0
? __pfx___probestub_irq_enable+0x3/0x10
? __create_object+0x5e/0x90
? security_capable+0x3b/0x70
rtnl_newlink+0x784/0xaf0
? avc_has_perm_noaudit+0x67/0xf0
? cred_has_capability.isra.0+0x75/0x110
? stack_depot_save_flags+0x24/0x6d0
? __pfx_rtnl_newlink+0x10/0x10
rtnetlink_rcv_msg+0x34f/0x3f0
? do_syscall_64+0x6c/0x180
? entry_SYSCALL_64_after_hwframe+0x76/0x7e
? __pfx_rtnetlink_rcv_msg+0x10/0x10
netlink_rcv_skb+0x54/0x100
netlink_unicast+0x23e/0x390
netlink_sendmsg+0x21e/0x490
____sys_sendmsg+0x31b/0x350
? copy_msghdr_from_user+0x6d/0xa0
___sys_sendmsg+0x86/0xd0
? __pte_offset_map+0x17/0x160
? preempt_count_add+0x69/0xa0
? __call_rcu_common.constprop.0+0x147/0x610
? preempt_count_add+0x69/0xa0
? preempt_count_add+0x69/0xa0
? _raw_spin_trylock+0x13/0x60
? trace_hardirqs_on+0x1d/0x80
__sys_sendmsg+0x66/0xc0
do_syscall_64+0x6c/0x180
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f41defe5b34
Code: 15 e1 12 0f 00 f7 d8 64 89 02 b8 ff ff ff ff eb bf 0f 1f 44 00 00
f3 0f 1e fa 80 3d 35 95 0f 00 00 74 13 b8 2e 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 4c c3 0f 1f 00 55 48 89 e5 48 83 ec 20 89 55
RSP: 002b:00007ffe5336ecc8 EFLAGS: 00000202 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f41defe5b34
RDX: 0000000000000000 RSI: 00007ffe5336ed30 RDI: 0000000000000003
RBP: 00007ffe5336eda0 R08: 0000000000000010 R09: 0000000000000001
R10: 00007ffe5336f6f9 R11: 0000000000000202 R12: 0000000000000003
R13: 0000000067452259 R14: 0000556ccc28b040 R15: 0000000000000000
</TASK>
[...]
Fixes: c8bd1f7f3e61 ("virtio_net: add support for Byte Queue Limits")
Cc: <stable@vger.kernel.org> # v6.11+
Signed-off-by: Koichiro Den <koichiro.den@canonical.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
[ pabeni: trimmed possibly troublesome separator ]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The 'select FB_CORE' statement moved from CONFIG_DRM to DRM_CLIENT_LIB,
but there are now configurations that have code calling into fb_core
as built-in even though the client_lib itself is a loadable module:
x86_64-linux-ld: drivers/gpu/drm/drm_fbdev_shmem.o: in function `drm_fbdev_shmem_driver_fbdev_probe':
drm_fbdev_shmem.c:(.text+0x1fc): undefined reference to `fb_deferred_io_init'
x86_64-linux-ld: drivers/gpu/drm/drm_fbdev_shmem.o: in function `drm_fbdev_shmem_fb_destroy':
drm_fbdev_shmem.c:(.text+0x2e1): undefined reference to `fb_deferred_io_cleanup'
In addition to DRM_CLIENT_LIB, the 'select' needs to be at least in
two more parts, DRM_KMS_HELPER and DRM_GEM_SHMEM_HELPER, so add those
here.
v3:
- Remove FB_CORE from DRM_KMS_HELPER to avoid circular dependency
Fixes: dadd28d4142f ("drm/client: Add client-lib module")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241115162323.3555229-1-arnd@kernel.org
|
|
Interrupt status (GPI_IS) register is cleared by writing 1 to it, not 0.
Cc: stable@vger.kernel.org
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-8-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
GPIO line can only be used as interrupt if its INTSEL register is
programmed by the BIOS.
Cc: stable@vger.kernel.org
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-7-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add check of HOSTSW_MODE bit to determine if GPIO pad can be used by the
driver.
Cc: stable@vger.kernel.org
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-6-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Correct RX Level/Edge Configuration register (RXEVCFG) bitmask.
Cc: stable@vger.kernel.org
Signed-off-by: Shankar Bandal <shankar.bandal@intel.com>
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-5-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Update GPI Interrupt Status register offset to correct value.
Cc: stable@vger.kernel.org
Signed-off-by: Shankar Bandal <shankar.bandal@intel.com>
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-4-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Base Address of vGPIO MMIO register is provided directly by the BIOS
instead of using offsets. Update address assignment to reflect this
change in driver.
Cc: stable@vger.kernel.org
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-3-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Move setting irq_chip.name from probe() function to the initialization
of "irq_chip" struct in order to fix vGPIO driver crash during bootup.
Crash was caused by unauthorized modification of irq_chip.name field
where irq_chip struct was initialized as const.
This behavior is a consequence of suboptimal implementation of
gpio_irq_chip_set_chip(), which should be changed to avoid
casting away const qualifier.
Crash log:
BUG: unable to handle page fault for address: ffffffffc0ba81c0
/#PF: supervisor write access in kernel mode
/#PF: error_code(0x0003) - permissions violation
CPU: 33 UID: 0 PID: 1075 Comm: systemd-udevd Not tainted 6.12.0-rc6-00077-g2e1b3cc9d7f7 #1
Hardware name: Intel Corporation Kaseyville RP/Kaseyville RP, BIOS KVLDCRB1.PGS.0026.D73.2410081258 10/08/2024
RIP: 0010:gnr_gpio_probe+0x171/0x220 [gpio_graniterapids]
Cc: stable@vger.kernel.org
Signed-off-by: Alan Borzeszkowski <alan.borzeszkowski@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20241204070415.1034449-2-mika.westerberg@linux.intel.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Add an assertion to all the iteration points that don't obviously
have the lock held already. These all take the locker higher in their
call chains.
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/2-v1-3b9edcf8067d+3975-amd_dev_list_locking_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The list domain->dev_list is protected by the domain->lock spinlock.
Any iteration, addition or removal must be under the lock.
Move the list_del() up into the critical section. pdom_is_sva_capable(),
and destroy_gcr3_table() do not interact with the list element.
Wrap the list_add() in a lock, it would make more sense if this was under
the same critical section as adjusting the refcounts earlier, but that
requires more complications.
Fixes: d6b47dec3684 ("iommu/amd: Reduce domain lock scope in attach device path")
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Vasant Hegde <vasant.hegde@amd.com>
Link: https://lore.kernel.org/r/1-v1-3b9edcf8067d+3975-amd_dev_list_locking_jgg@nvidia.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Due to target variable is being reassigned in npc_install_flow()
function, PF multicast rules are not getting installed.
This patch addresses the issue by fixing the "IF" condition
checks when rules are installed by AF.
Fixes: 6c40ca957fe5 ("octeontx2-pf: Adds TC offload support").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241205113435.10601-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If traffic is over vlan, cma_validate_port() fails to match
net_device ifindex with bound_if_index and results in ENODEV error.
As iWARP gid table is static, it contains entry corresponding to
only one net device which is either real netdev or vlan netdev for
cases like siw attached to a vlan interface.
This patch fixes the issue by assigning bound_if_index with net
device index, if real net device obtained from bound if index matches
with net device retrieved from gid table
Fixes: f8ef1be816bf ("RDMA/cma: Avoid GID lookups on iWARP devices")
Link: https://lore.kernel.org/all/ZzNgdrjo1kSCGbRz@chelsio.com/
Signed-off-by: Anumula Murali Mohan Reddy <anumula@chelsio.com>
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Link: https://patch.msgid.link/20241203140052.3985-1-anumula@chelsio.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Intel Panther Lake-M/P has the same integrated Thunderbolt/USB4
controller as Lunar Lake. Add these PCI IDs to the driver list of
supported devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Offset based on (id * size) is wrong for sqc and cqc.
(*sqc/*cqc + 1) can already offset sizeof(struct(Xqc)) length.
Fixes: 15f112f9cef5 ("crypto: hisilicon/debugfs - mask the unnecessary info from the dump")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Booting with amd-pstate on 3rd Generation EPYC system incorrectly
enabled ITMT support despite the system not supporting Preferred Core
ranking. amd_pstate_init_prefcore() called during amd_pstate*_cpu_init()
requires "amd_pstate_prefcore" to be set correctly however the preferred
core support is detected only after driver registration which is too
late.
Swap the function calls around to detect preferred core support before
registring the driver via amd_pstate_register_driver(). This ensures
amd_pstate*_cpu_init() sees the correct value of "amd_pstate_prefcore"
considering the platform support.
Fixes: 279f838a61f9 ("x86/amd: Detect preferred cores in amd_get_boost_ratio_numerator()")
Fixes: ff2653ded4d9 ("cpufreq/amd-pstate: Move registration after static function call update")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Acked-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241210032557.754-1-kprateek.nayak@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
lrbp->compl_time_stamp_local_clock is set to zero after sending a sqe
but it is not updated after completing a cqe. Thus the printed
information in ufshcd_print_tr() will always be zero.
Update lrbp->cmpl_time_stamp_local_clock after completing a cqe.
Log sample:
ufshcd-qcom 1d84000.ufshc: UPIU[8] - issue time 8750227249 us
ufshcd-qcom 1d84000.ufshc: UPIU[8] - complete time 0 us
Fixes: c30d8d010b5e ("scsi: ufs: core: Prepare for completion in MCQ")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Peter Wang <peter.wang@mediatek.com>
Signed-off-by: liuderong <liuderong@oppo.com>
Link: https://lore.kernel.org/r/1733470182-220841-1-git-send-email-liuderong@oppo.com
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The module parameter qcaspi_pluggable controls if QCA7000 signature
should be checked at driver probe (current default) or not. Unfortunately
this could fail in case the chip is temporary in reset, which isn't under
total control by the Linux host. So disable this check per default
in order to avoid unexpected probe failures.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-3-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Storing the maximum clock speed in module parameter qcaspi_clkspeed
has the unintended side effect that the first probed instance
defines the value for all other instances. Fix this issue by storing
it in max_speed_hz of the relevant SPI device.
This fix keeps the priority of the speed parameter (module parameter,
device tree property, driver default). Btw this uses the opportunity
to get the rid of the unused member clkspeed.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://patch.msgid.link/20241206184643.123399-2-wahrenst@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ECs implementing the v2 command will not stop charging when the end
threshold is reached. Instead they will begin discharging until the
start threshold is reached, leading to permanent charge and discharge
cycles. This defeats the point of the charge control mechanism.
Avoid the issue by hiding the start threshold on v2 systems.
Instead on those systems program the EC with start == end which forces
the EC to reach and stay at that level.
v1 does not support thresholds and v3 works correctly,
at least judging from the code.
Reported-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef5259 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-3-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Allow setting the start and stop thresholds to the same value.
There is no reason to disallow it.
Suggested-by: Thomas Koch <linrunner@gmx.net>
Fixes: c6ed48ef5259 ("power: supply: add ChromeOS EC based charge control driver")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241208-cros_charge-control-v2-v1-2-8d168d0f08a3@weissschuh.net
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
