| Age | Commit message (Collapse) | Author |
|---|
|
There is an upper bound to the value that a watermark may hold. That
upper bound is not immediately obvious during configuration, and it
might be possible to have accidental truncation.
Actually this has happened already, add a warning to prevent it from
happening again.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tail dropping is enabled for a port when:
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that in some cases there are EC events to flush in
acpi_ec_dispatch_gpe() even though the ec_no_wakeup kernel parameter
is set and the EC GPE is disabled while sleeping, so drop the
ec_no_wakeup check that prevents those events from being processed
from acpi_ec_dispatch_gpe().
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 607b9df63057 ("ACPI: EC: PM: Avoid flushing EC work when EC
GPE is inactive") has been reported to cause some power button wakeup
events to be missed on some systems, so modify acpi_ec_dispatch_gpe()
to call acpi_ec_flush_work() unconditionally to effectively reverse
the changes made by that commit.
Also note that the problem which prompted commit 607b9df63057 is not
reproducible any more on the affected machine.
Fixes: 607b9df63057 ("ACPI: EC: PM: Avoid flushing EC work when EC GPE is inactive")
Reported-by: Raymond Tan <raymond.tan@intel.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq updates for 5.10-rc1 from Viresh Kumar:
"- STI cpufreq driver updates to allow new hardware (Alain Volmat).
- Minor tegra driver fixes around initial frequency mismatch warnings (Jon
Hunter).
- dev_err simplification for s5pv210 driver (Krzysztof Kozlowski).
- Qcom driver updates to allow new hardware and minor cleanup (Manivannan
Sadhasivam and Matthias Kaehlcke).
- Add missing MODULE_DEVICE_TABLE for armada driver (Pali Rohár).
- Improved defer-probe handling in cpufreq-dt driver (Stephan Gerhold).
- Call dev_pm_opp_of_remove_table() unconditionally for imx driver (Viresh
Kumar)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom: Don't add frequencies without an OPP
cpufreq: qcom-hw: Add cpufreq support for SM8250 SoC
cpufreq: qcom-hw: Use of_device_get_match_data for offsets and row size
cpufreq: qcom-hw: Use devm_platform_ioremap_resource() to simplify code
dt-bindings: cpufreq: cpufreq-qcom-hw: Document Qcom EPSS compatible
cpufreq: qcom-hw: Make use of cpufreq driver_data for passing pdev
cpufreq: armada-37xx: Add missing MODULE_DEVICE_TABLE
cpufreq: arm: Kconfig: add CPUFREQ_DT depend for STI CPUFREQ
cpufreq: dt-platdev: Blacklist st,stih418 SoC
cpufreq: sti-cpufreq: add stih418 support
cpufreq: s5pv210: Use dev_err instead of pr_err in probe
cpufreq: s5pv210: Simplify with dev_err_probe()
cpufreq: tegra186: Fix initial frequency
cpufreq: dt: Refactor initialization to handle probe deferral properly
opp: Handle multiple calls for same OPP table in _of_add_opp_table_v1()
cpufreq: imx6q: Unconditionally call dev_pm_opp_of_remove_table()
opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER
|
|
Kexec can directly boot into a new kernel without going to complete
reboot. This can leave the previous kernel's configuration for PDC
interrupts as is.
Clear previous kernel's configuration during init by setting interrupts
in enable bank to zero. The IRQs specified in qcom,pdc-ranges property
are the only ones that can be used by the new kernel so clear only those
IRQs. The remaining ones may be in use by a different kernel and should
not be set by new kernel.
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-7-git-send-email-mkshah@codeaurora.org
|
|
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-6-git-send-email-mkshah@codeaurora.org
|
|
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-5-git-send-email-mkshah@codeaurora.org
|
|
msmgpio irqchip was not using return value of irq_set_irq_wake() callback
since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor
it implemented .irq_set_wake callback. This lead to irq_set_irq_wake()
return error -ENXIO.
However from 'commit 4110b5cbb014 ("irqchip/gic-v3: Allow interrupt to be
configured as wake-up sources")' GIC irqchip has IRQCHIP_SKIP_SET_WAKE
flag.
Use return value from irq_set_irq_wake() and irq_chip_set_wake_parent()
instead of always returning success.
Fixes: e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-3-git-send-email-mkshah@codeaurora.org
|
|
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes: e35a6ae0eb3a ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-2-git-send-email-mkshah@codeaurora.org
|
|
Recent laptops with dual AMD GPUs fail to suspend the discrete GPU, thus
causing lockups on system sleep and high power consumption at runtime.
The discrete GPU would normally be suspended to D3cold by turning off
ACPI _PR3 Power Resources of the Root Port above the GPU.
However on affected systems, the Root Port is hotplug-capable and
pci_bridge_d3_possible() only allows hotplug ports to go to D3 if they
belong to a Thunderbolt device or if the Root Port possesses a
"HotPlugSupportInD3" ACPI property. Neither is the case on affected
laptops. The reason for whitelisting only specific, known to work
hotplug ports for D3 is that there have been reports of SkyLake Xeon-SP
systems raising Hardware Error NMIs upon suspending their hotplug ports:
https://lore.kernel.org/linux-pci/20170503180426.GA4058@otc-nc-03/
But if a hotplug port is power manageable by ACPI (as can be detected
through presence of Power Resources and corresponding _PS0 and _PS3
methods) then it ought to be safe to suspend it to D3. To this end,
amend acpi_pci_bridge_d3() to whitelist such ports for D3.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1222
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1252
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1304
Reported-and-tested-by: Arthur Borsboom <arthurborsboom@gmail.com>
Reported-and-tested-by: matoro <matoro@airmail.cc>
Reported-by: Aaron Zakhrov <aaron.zakhrov@gmail.com>
Reported-by: Michal Rostecki <mrostecki@suse.com>
Reported-by: Shai Coleman <git@shaicoleman.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In reaction to a proposal to introduce a memcpy_mcsafe_fast()
implementation Linus points out that memcpy_mcsafe() is poorly named
relative to communicating the scope of the interface. Specifically what
addresses are valid to pass as source, destination, and what faults /
exceptions are handled.
Of particular concern is that even though x86 might be able to handle
the semantics of copy_mc_to_user() with its common copy_user_generic()
implementation other archs likely need / want an explicit path for this
case:
On Fri, May 1, 2020 at 11:28 AM Linus Torvalds <torvalds@linux-foundation.org> wrote:
>
> On Thu, Apr 30, 2020 at 6:21 PM Dan Williams <dan.j.williams@intel.com> wrote:
> >
> > However now I see that copy_user_generic() works for the wrong reason.
> > It works because the exception on the source address due to poison
> > looks no different than a write fault on the user address to the
> > caller, it's still just a short copy. So it makes copy_to_user() work
> > for the wrong reason relative to the name.
>
> Right.
>
> And it won't work that way on other architectures. On x86, we have a
> generic function that can take faults on either side, and we use it
> for both cases (and for the "in_user" case too), but that's an
> artifact of the architecture oddity.
>
> In fact, it's probably wrong even on x86 - because it can hide bugs -
> but writing those things is painful enough that everybody prefers
> having just one function.
Replace a single top-level memcpy_mcsafe() with either
copy_mc_to_user(), or copy_mc_to_kernel().
Introduce an x86 copy_mc_fragile() name as the rename for the
low-level x86 implementation formerly named memcpy_mcsafe(). It is used
as the slow / careful backend that is supplanted by a fast
copy_mc_generic() in a follow-on patch.
One side-effect of this reorganization is that separating copy_mc_64.S
to its own file means that perf no longer needs to track dependencies
for its memcpy_64.S benchmarks.
[ bp: Massage a bit. ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Link: http://lore.kernel.org/r/CAHk-=wjSqtXAqfUJxFtWNwmguFASTgB0dz1dT3V-78Quiezqbg@mail.gmail.com
Link: https://lkml.kernel.org/r/160195561680.2163339.11574962055305783722.stgit@dwillia2-desk3.amr.corp.intel.com
|
|
different models
Commit b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for
SW_TABLET_MODE") added support for reporting SW_TABLET_MODE using the
Asus 0x00120063 WMI-device-id to see if various transformer models were
docked into their keyboard-dock (SW_TABLET_MODE=0) or if they were
being used as a tablet.
The new SW_TABLET_MODE support (naively?) assumed that non Transformer
devices would either not support the 0x00120063 WMI-device-id at all,
or would NOT set ASUS_WMI_DSTS_PRESENCE_BIT in their reply when querying
the device-id.
Unfortunately this is not true and we have received many bug reports about
this change causing the asus-wmi driver to always report SW_TABLET_MODE=1
on non Transformer devices. This causes libinput to think that these are
360 degree hinges style 2-in-1s folded into tablet-mode. Making libinput
suppress keyboard and touchpad events from the builtin keyboard and
touchpad. So effectively this causes the keyboard and touchpad to not work
on many non Transformer Asus models.
This commit fixes this by using the existing DMI based quirk mechanism in
asus-nb-wmi.c to allow using the 0x00120063 device-id for reporting
SW_TABLET_MODE on Transformer models and ignoring it on all other models.
Fixes: b0dbd97de1f1 ("platform/x86: asus-wmi: Add support for SW_TABLET_MODE")
Link: https://patchwork.kernel.org/patch/11780901/
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209011
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1876997
Reported-by: Samuel Čavoj <samuel@cavoj.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.9:
- Small doc fix.
- Re-add FB_ARMCLCD for android.
- Fix global-out-of-bounds read in fbcon_get_font().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8585daa2-fcbc-3924-ac4f-e7b5668808e0@linux.intel.com
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
"We have some fixes for Tablet Mode reporting in particular, that users
are complaining a lot about.
Summary:
- Attempt #3 of enabling Tablet Mode reporting w/o regressions
- Improve battery recognition code in ASUS WMI driver
- Fix Kconfig dependency warning for Fujitsu and LG laptop drivers
- Add fixes in Thinkpad ACPI driver for _BCL method and NVRAM polling
- Fix power supply extended topology in Mellanox driver
- Fix memory leak in OLPC EC driver
- Avoid static struct device in Intel PMC core driver
- Add support for the touchscreen found in MPMAN Converter9 2-in-1
- Update MAINTAINERS to reflect the real state of affairs"
* tag 'platform-drivers-x86-v5.9-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: re-initialize ACPI buffer size when reuse
MAINTAINERS: Add Mark Gross and Hans de Goede as x86 platform drivers maintainers
platform/x86: intel-vbtn: Switch to an allow-list for SW_TABLET_MODE reporting
platform/x86: intel-vbtn: Revert "Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360"
platform/x86: intel_pmc_core: do not create a static struct device
platform/x86: mlx-platform: Fix extended topology configuration for power supply units
platform/x86: pcengines-apuv2: Fix typo on define of AMD_FCH_GPIO_REG_GPIO55_DEVSLP0
platform/x86: fix kconfig dependency warning for FUJITSU_LAPTOP
platform/x86: fix kconfig dependency warning for LG_LAPTOP
platform/x86: thinkpad_acpi: initialize tp_nvram_state variable
platform/x86: intel-vbtn: Fix SW_TABLET_MODE always reporting 1 on the HP Pavilion 11 x360
platform/x86: asus-wmi: Add BATC battery name to the list of supported
platform/x86: asus-nb-wmi: Revert "Do not load on Asus T100TA and T200TA"
platform/x86: touchscreen_dmi: Add info for the MPMAN Converter9 2-in-1
Documentation: laptops: thinkpad-acpi: fix underline length build warning
Platform: OLPC: Fix memleak in olpc_ec_probe
|
|
If both LED banks aren't used in device tree, an out-of-bounds
condition in lm3697_init occurs because of the for loop assuming that
all the banks are used. Fix it by adding a variable that contains the
number of used banks.
Signed-off-by: Gabriel David <ultracoolguy@tutanota.com>
[removed extra rename, minor tweaks]
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Cc: stable@kernel.org
|
|
On an error exit path, a negative error code should be returned
instead of a positive return value.
Fixes: 90b2d4f15ff7 ("ipmi_si: Remove hacks for adding a dummy platform devices")
Cc: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Message-Id: <20201005145212.84435-1-tianjia.zhang@linux.alibaba.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Pull networking fixes from David Miller:
1) Make sure SKB control block is in the proper state during IPSEC
ESP-in-TCP encapsulation. From Sabrina Dubroca.
2) Various kinds of attributes were not being cloned properly when we
build new xfrm_state objects from existing ones. Fix from Antony
Antony.
3) Make sure to keep BTF sections, from Tony Ambardar.
4) TX DMA channels need proper locking in lantiq driver, from Hauke
Mehrtens.
5) Honour route MTU during forwarding, always. From Maciej
Żenczykowski.
6) Fix races in kTLS which can result in crashes, from Rohit
Maheshwari.
7) Skip TCP DSACKs with rediculous sequence ranges, from Priyaranjan
Jha.
8) Use correct address family in xfrm state lookups, from Herbert Xu.
9) A bridge FDB flush should not clear out user managed fdb entries
with the ext_learn flag set, from Nikolay Aleksandrov.
10) Fix nested locking of netdev address lists, from Taehee Yoo.
11) Fix handling of 32-bit DATA_FIN values in mptcp, from Mat Martineau.
12) Fix r8169 data corruptions on RTL8402 chips, from Heiner Kallweit.
13) Don't free command entries in mlx5 while comp handler could still be
running, from Eran Ben Elisha.
14) Error flow of request_irq() in mlx5 is busted, due to an off by one
we try to free and IRQ never allocated. From Maor Gottlieb.
15) Fix leak when dumping netlink policies, from Johannes Berg.
16) Sendpage cannot be performed when a page is a slab page, or the page
count is < 1. Some subsystems such as nvme were doing so. Create a
"sendpage_ok()" helper and use it as needed, from Coly Li.
17) Don't leak request socket when using syncookes with mptcp, from
Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
net/core: check length before updating Ethertype in skb_mpls_{push,pop}
net: mvneta: fix double free of txq->buf
net_sched: check error pointer in tcf_dump_walker()
net: team: fix memory leak in __team_options_register
net: typhoon: Fix a typo Typoon --> Typhoon
net: hinic: fix DEVLINK build errors
net: stmmac: Modify configuration method of EEE timers
tcp: fix syn cookied MPTCP request socket leak
libceph: use sendpage_ok() in ceph_tcp_sendpage()
scsi: libiscsi: use sendpage_ok() in iscsi_tcp_segment_map()
drbd: code cleanup by using sendpage_ok() to check page for kernel_sendpage()
tcp: use sendpage_ok() to detect misused .sendpage
nvme-tcp: check page by sendpage_ok() before calling kernel_sendpage()
net: add WARN_ONCE in kernel_sendpage() for improper zero-copy send
net: introduce helper sendpage_ok() in include/linux/net.h
net: usb: pegasus: Proper error handing when setting pegasus' MAC address
net: core: document two new elements of struct net_device
netlink: fix policy dump leak
net/mlx5e: Fix race condition on nhe->n pointer in neigh update
net/mlx5e: Fix VLAN create flow
...
|
|
|
|
For particular codec HWs have requirement to toggle interrupt clear
register twice 0->1->0. To accommodate it, need to add one more field
(clear_ack) in the regmap_irq struct and update regmap-irq driver to
support it.
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Link: https://lore.kernel.org/r/1601907440-13373-1-git-send-email-lkasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
bio_crypt_clone() assumes its gfp_mask argument always includes
__GFP_DIRECT_RECLAIM, so that the mempool_alloc() will always succeed.
However, bio_crypt_clone() might be called with GFP_ATOMIC via
setup_clone() in drivers/md/dm-rq.c, or with GFP_NOWAIT via
kcryptd_io_read() in drivers/md/dm-crypt.c.
Neither case is currently reachable with a bio that actually has an
encryption context. However, it's fragile to rely on this. Just make
bio_crypt_clone() able to fail, analogous to bio_integrity_clone().
Reported-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Satya Tangirala <satyat@google.com>
Cc: Satya Tangirala <satyat@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
DRBD keeps a block device open just to get and set the capacity from
it. Switch to primarily using the disk capacity as intended by the
block layer, and sync it to the bdev using revalidate_disk_size.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Remove the duplicate "Mellanox" in the help text for the Mellanox FAN
driver configuration option.
Fixes: 65afb4c8e7e4e7e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201005124843.26688-1-geert+renesas@glider.be
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add debugfs interface support for accessing device specific registers
(MFR_VOUT_MIN, MFR_DEVSET1 and MFR_DEVSET2) and others including
OPERATION, ON_OFF_CONFIG, SMB_ALERT_MASK, VOUT_MODE, VOUT_COMMAND
and VOUT_MAX.
Signed-off-by: Ugur Usug <ugur.usug@maximintegrated.com>
Link: https://lore.kernel.org/r/MWHPR11MB1965C01083AD013C630646B2FD3B0@MWHPR11MB1965.namprd11.prod.outlook.com
[groeck: Resolved conflics seen due to PMBus driver API changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The max34* family have the IOUT_OC_WARN_LIMIT and IOUT_OC_CRIT_LIMIT
registers swapped.
Cc: stable@vger.kernel.org
Signed-off-by: Steve Foreman <foremans@google.com>
[groeck: Updated subject, use C comment style, tab after defines]
[groeck: Added missing break; statements (by alexandru.ardelean@analog.com)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
|
|
If the SPI controller has has_dmamode = true and spi_bitbang_start() fails
in spi_imx_probe(), then the driver must release the DMA channels acquired
in spi_imx_sdma_init() by calling spi_imx_sdma_exit() in the fail path.
Fixes: f62caccd12c1 ("spi: spi-imx: add DMA support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Robin Gong <b38343@freescale.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20201005132229.513119-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The print in probe is done using pr_info. Correct print call would be
dev_dbg because:
- Severity should really be dbg
- The dev pointer is given as first argument
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/c4f55add237455555df0597c72052022f7a669f6.1601885841.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The PM8953 is commonly used on board with MSM8953 SoCs or its variants:
APQ8053, SDM(SDA)450 and SDM(SDA)632.
It provides 7 SMPS and 23 LDO regulators.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Link: https://lore.kernel.org/r/20201004083413.324351-1-junak.pub@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If debugging is disabled, print_constraints() does not print the actual
constraints, but still performs some processing and string formatting,
only to throw away the result later.
Fix this by moving all constraint debug processing to a separate
function, and replacing it by a dummy when debugging is disabled.
This reduces kernel size by almost 800 bytes (on arm/arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201005131546.22448-1-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cpufreq core handles the updates to policy->cur and recording of
cpufreq trace events for all the governors except schedutil's fast
switch case.
Move that as well to cpufreq core for consistency and readability.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Now that all the blockers are gone for enabling stats in fast-switching
case, enable it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since this will be part of the scheduler's hotpath in some cases, use
unlikely() for few of the obvious conditionals.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The locking isn't required anymore as stats can get updated only from
one place at a time. Remove it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In order to prepare for lock-less stats update, add support to defer any
updates to it until cpufreq_stats_record_transition() is called.
The stats were updated from two places earlier:
- show_time_in_state(): This can be easily deferred, all we need is to
calculate the delta duration again in this routine to show the current
state's time-in-state.
- store_reset(): This is a bit tricky as we need to clear the stats
here and avoid races with simultaneous call to
cpufreq_stats_record_transition().
Fix that by deferring the reset of the stats (within the code) to the
next call to cpufreq_stats_record_transition(), but since we need to
keep showing the right stats until that time, we capture the reset
time and account for the time since last time reset was called until
the time cpufreq_stats_record_transition() update the stats.
User space will continue seeing the stats correctly, everything will
be 0 after the stats are reset, apart from the time-in-state of the
current state, until the time a frequency switch happens.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After some unsuccessful attempts to use sysrq over console, figured
out that port->has_sysrq should likely be enabled, as per other
architectures, this when CONFIG_SERIAL_MCF_CONSOLE is also enabled.
Tested some magic sysrq commands (h, p, t, b), they works now
properly. Commands works inside 5 secs after BREAK is sent, as
expected.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201002140545.477481-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add handling of magic sysrq keys when using dma/edma.
Tested by sending BREAK followed by a sysrq command inside
a 5 secs time window, by:
echo 1 > /proc/sys/kernel/sysrq
BREAK + h, t, e, b, c
Tested also sending a command after 5 secs after BREAK, that's
properly ignored.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201004161144.1307174-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull opertaing performance points (OPP) framework fixes for 5.10-rc1
from Viresh Kumar:
"- Return -EPROBE_DEFER properly from dev_pm_opp_get_opp_table()
(Stephan Gerhold).
- Minor cleanups around required-opps (Stephan Gerhold).
- Extends opp-supported-hw property to contain multiple versions
(Viresh Kumar).
- Multiple cleanups around dev_pm_opp_attach_genpd() (Viresh Kumar).
- Multiple fixes, cleanups in the OPP core for overall better design
(Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Allow opp-level to be set to 0
opp: Prevent memory leak in dev_pm_opp_attach_genpd()
ARM: tegra: Pass multiple versions in opp-supported-hw property
opp: Allow opp-supported-hw to contain multiple versions
dt-bindings: opp: Allow opp-supported-hw to contain multiple versions
opp: Set required OPPs in reverse order when scaling down
opp: Reduce code duplication in _set_required_opps()
opp: Drop unnecessary check from dev_pm_opp_attach_genpd()
opp: Handle multiple calls for same OPP table in _of_add_opp_table_v1()
opp: Allow dev_pm_opp_get_opp_table() to return -EPROBE_DEFER
opp: Remove _dev_pm_opp_find_and_remove_table() wrapper
opp: Split out _opp_set_rate_zero()
opp: Reuse the enabled flag in !target_freq path
opp: Rename regulator_enabled and use it as status of all resources
|
|
The original intent of 84d3f6b76447 was to delay evaluating lid state until
all drivers have been loaded, with input device being opened from userspace
serving as a signal for this condition. Let's ensure that state updates
happen even if userspace closed (or in the future inhibited) input device.
Note that if we go through suspend/resume cycle we assume the system has
been fully initialized even if LID input device has not been opened yet.
This has a side-effect of fixing access to input->users outside of
input->mutex protections by the way of eliminating said accesses and using
driver private flag.
Fixes: 84d3f6b76447 ("ACPI / button: Delay acpi_lid_initialize_state() until first user space open")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
* pm-cpuidle:
cpuidle: record state entry rejection statistics
cpuidle: psci: Allow PM domain to be initialized even if no OSI mode
firmware: psci: Extend psci_set_osi_mode() to allow reset to PC mode
ACPI: processor: Print more information when acpi_processor_evaluate_cst() fails
cpuidle: tegra: Correctly handle result of arm_cpuidle_simple_enter()
|
|
Evaluating ACPI _BCL could fail, then ACPI buffer size will be set to 0.
When reuse this ACPI buffer, AE_BUFFER_OVERFLOW will be triggered.
Re-initialize buffer size will make ACPI evaluate successfully.
Fixes: 46445b6b896fd ("thinkpad-acpi: fix handle locate for video and query of _BCL")
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60b1 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
drivers/mfd/kempld-core.c:556:36: warning: unused variable 'kempld_acpi_table' [-Wunused-const-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Fixes the following randconfig build error:
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
simple-mfd-i2c.c:(.text+0x48): undefined reference to `__devm_regmap_init_i2c'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_init':
simple-mfd-i2c.c:(.init.text+0x14): undefined reference to `i2c_register_driver'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_exit':
simple-mfd-i2c.c:(.exit.text+0xd): undefined reference to `i2c_del_driver'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
After commit 9f51c05dc41a ("pvcalls-front: Avoid
get_free_pages(GFP_KERNEL) under spinlock"), the variable ret is being
initialized with '-ENOMEM' that is meaningless. So remove it.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Link: https://lore.kernel.org/r/20200919031702.32192-1-jingxiangfeng@huawei.com
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
In 2019, we introduced pin_user_pages*() and now we are converting
get_user_pages*() to the new API as appropriate. [1] & [2] could
be referred for more information. This is case 5 as per document [1].
[1] Documentation/core-api/pin_user_pages.rst
[2] "Explicit pinning of user-space pages":
https://lwn.net/Articles/807108/
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Link: https://lore.kernel.org/r/1599375114-32360-2-git-send-email-jrdr.linux@gmail.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
There seems to be a bug in the original code when gntdev_get_page()
is called with writeable=true then the page needs to be marked dirty
before being put.
To address this, a bool writeable is added in gnt_dev_copy_batch, set
it in gntdev_grant_copy_seg() (and drop `writeable` argument to
gntdev_get_page()) and then, based on batch->writeable, use
set_page_dirty_lock().
Fixes: a4cdb556cae0 (xen/gntdev: add ioctl for grant copy)
Suggested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1599375114-32360-1-git-send-email-jrdr.linux@gmail.com
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
clang static analysis reports this problem:
drivers/net/ethernet/marvell/mvneta.c:3465:2: warning:
Attempt to free released memory
kfree(txq->buf);
^~~~~~~~~~~~~~~
When mvneta_txq_sw_init() fails to alloc txq->tso_hdrs,
it frees without poisoning txq->buf. The error is caught
in the mvneta_setup_txqs() caller which handles the error
by cleaning up all of the txqs with a call to
mvneta_txq_sw_deinit which also frees txq->buf.
Since mvneta_txq_sw_deinit is a general cleaner, all of the
partial cleaning in mvneta_txq_sw_deinit()'s error handling
is not needed.
Fixes: 2adb719d74f6 ("net: mvneta: Implement software TSO")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
