| Age | Commit message (Collapse) | Author |
|---|
|
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb48898 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MMIO space is wider now so we mask the lower 22 bits
instead of 18.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
OLAND 0x1002:0x6604 0x1028:0x066F 0x00 seems to have problems
with higher sclks.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
OLAND 0x1002:0x6604 0x1028:0x066F 0x00 seems to have problems
with higher sclks.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling
support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch fixes netdev->features for Extended Socket network device.
Currently Extended Socket network device's netdev->feature claims
NETIF_F_HW_CSUM, however this is completely wrong. There's no feature
of checksum offloading.
That causes invalid TCP/UDP checksum and packet rejection when IP
forwarding from Extended Socket network device to other network device.
NETIF_F_HW_CSUM should be omitted.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a rather large set of fixes. The bulk are for lpfc correcting
a lot of issues in the new NVME driver code which just went in in the
merge window.
The others are:
- fix a hang in the vmware paravirt driver caused by incorrect
handling of the new MSI vector allocation
- long standing bug in storvsc, which recent block changes turned
from being a harmless annoyance into a hang
- yet more fallout (in mpt3sas) from the changes to device blocking
The remainder are small fixes and updates"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (34 commits)
scsi: lpfc: Add shutdown method for kexec
scsi: storvsc: Workaround for virtual DVD SCSI version
scsi: lpfc: revise version number to 11.2.0.10
scsi: lpfc: code cleanups in NVME initiator discovery
scsi: lpfc: code cleanups in NVME initiator base
scsi: lpfc: correct rdp diag portnames
scsi: lpfc: remove dead sli3 nvme code
scsi: lpfc: correct double print
scsi: lpfc: Rename LPFC_MAX_EQ_DELAY to LPFC_MAX_EQ_DELAY_EQID_CNT
scsi: lpfc: Rework lpfc Kconfig for NVME options
scsi: lpfc: add transport eh_timed_out reference
scsi: lpfc: Fix eh_deadline setting for sli3 adapters.
scsi: lpfc: add NVME exchange aborts
scsi: lpfc: Fix nvme allocation bug on failed nvme_fc_register_localport
scsi: lpfc: Fix IO submission if WQ is full
scsi: lpfc: Fix NVME CMD IU byte swapped word 1 problem
scsi: lpfc: Fix RCTL value on NVME LS request and response
scsi: lpfc: Fix crash during Hardware error recovery on SLI3 adapters
scsi: lpfc: fix missing spin_unlock on sql_list_lock
scsi: lpfc: don't dereference dma_buf->iocbq before null check
...
|
|
Reviewing the result of what was just added for Kconfig, we made a poor
choice. It worked well for full kernel builds, but not so much for how
it would be deployed on a distro.
Here's the final result:
- lpfc will compile in NVME initiator and/or NVME target support based
on whether the kernel has the corresponding subsystem support.
Kconfig is not used to drive this specifically for lpfc.
- There is a module parameter, lpfc_enable_fc4_type, that indicates
whether the ports will do FCP-only or FCP & NVME (NVME-only not yet
possible due to dependency on fc transport). As FCP & NVME divvys up
exchange resources, and given NVME will not be often initially, the
default is changed to FCP only.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix compilation warning:
drivers/scsi/ufs/ufshcd.c:7645:13: warning: comparison of unsigned
expression < 0 is always false [-Wtype-limits]
if ((value < UFS_PM_LVL_0) || (value >= UFS_PM_LVL_MAX))
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Resets can take longer than DEFAULT_TIMEOUT.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid rescan storms. No need to queue another if one is pending.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
- Add in a new case for volume offline. Resolves internal testing bug
for multilun array management.
- Return correct status for failed TURs.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- self-test failure of crc32c on powerpc
- regressions of ecb(aes) when used with xts/lrw in s5p-sss
- a number of bugs in the omap RNG driver
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s5p-sss - Fix spinlock recursion on LRW(AES)
hwrng: omap - Do not access INTMASK_REG on EIP76
hwrng: omap - use devm_clk_get() instead of of_clk_get()
hwrng: omap - write registers after enabling the clock
crypto: s5p-sss - Fix completing crypto request in IRQ handler
crypto: powerpc - Fix initialisation of crc32c context
|
|
Currently, intel_pstate_update_perf_limits() first converts the
policy minimum and maximum limits into percentages of the maximum
turbo frequency (rounding up to an integer) and then converts these
percentages to fractions (by using fixed-point arithmetic to divide
them by 100).
That introduces a rounding error unnecessarily, because the fractions
can be obtained by carrying out fixed-point divisions directly on the
input numbers.
Rework the computations in intel_pstate_hwp_set() to use fractions
instead of percentages (and drop redundant local variables from
there) and modify intel_pstate_update_perf_limits() to compute the
fractions directly and percentages out of them.
While at it, introduce percent_ext_fp() for converting percentages
to fractions (with extended number of fraction bits) and use it in
the computations.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This adds Intel(R) Trace Hub PCI ID for Gemini Lake SOC.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
|
|
This adds Intel(R) Trace Hub PCI ID for Denverton SOC.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
|
|
Output 'activation' may fail for the reasons of the output driver,
for example, if msc's buffer is not allocated. We forget, however,
to drop the module reference in this case. So each attempt at
activation in this case leaks a reference, preventing the module
from ever unloading.
This patch adds the missing module_put() in the activation error
path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v4.8+
|
|
Geminilake's DMC is not yet available in the linux-firmware repository.
To prevent userspace tools such as mkinitramfs to complain about
missing firmware, remove the MODULE_FIRMWARE() tag for now.
Fixes: dbb28b5c3d3c ("drm/i915/DMC/GLK: Load DMC on GLK")
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <drm-intel-fixes@lists.freedesktop.org>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170306085651.14008-1-ander.conselvan.de.oliveira@intel.com
Link: http://patchwork.freedesktop.org/patch/msgid/20170315095747.21845-1-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d9321a03efcda867b3a8c6327e01808516f0acd7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Pull networking fixes from David Miller:
1) Ensure that mtu is at least IPV6_MIN_MTU in ipv6 VTI tunnel driver,
from Steffen Klassert.
2) Fix crashes when user tries to get_next_key on an LPM bpf map, from
Alexei Starovoitov.
3) Fix detection of VLAN fitlering feature for bnx2x VF devices, from
Michal Schmidt.
4) We can get a divide by zero when TCP socket are morphed into
listening state, fix from Eric Dumazet.
5) Fix socket refcounting bugs in skb_complete_wifi_ack() and
skb_complete_tx_timestamp(). From Eric Dumazet.
6) Use after free in dccp_feat_activate_values(), also from Eric
Dumazet.
7) Like bonding team needs to use ETH_MAX_MTU as netdev->max_mtu, from
Jarod Wilson.
8) Fix use after free in vrf_xmit(), from David Ahern.
9) Don't do UDP Fragmentation Offload on IPComp ipsec packets, from
Alexey Kodanev.
10) Properly check napi_complete_done() return value in order to decide
whether to re-enable IRQs or not in amd-xgbe driver, from Thomas
Lendacky.
11) Fix double free of hwmon device in marvell phy driver, from Andrew
Lunn.
12) Don't crash on malformed netlink attributes in act_connmark, from
Etienne Noss.
13) Don't remove routes with a higher metric in ipv6 ECMP route replace,
from Sabrina Dubroca.
14) Don't write into a cloned SKB in ipv6 fragmentation handling, from
Florian Westphal.
15) Fix routing redirect races in dccp and tcp, basically the ICMP
handler can't modify the socket's cached route in it's locked by the
user at this moment. From Jon Maxwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (108 commits)
qed: Enable iSCSI Out-of-Order
qed: Correct out-of-bound access in OOO history
qed: Fix interrupt flags on Rx LL2
qed: Free previous connections when releasing iSCSI
qed: Fix mapping leak on LL2 rx flow
qed: Prevent creation of too-big u32-chains
qed: Align CIDs according to DORQ requirement
mlxsw: reg: Fix SPVMLR max record count
mlxsw: reg: Fix SPVM max record count
net: Resend IGMP memberships upon peer notification.
dccp: fix memory leak during tear-down of unsuccessful connection request
tun: fix premature POLLOUT notification on tun devices
dccp/tcp: fix routing redirect race
ucc/hdlc: fix two little issue
vxlan: fix ovs support
net: use net->count to check whether a netns is alive or not
bridge: drop netfilter fake rtable unconditionally
ipv6: avoid write to a possibly cloned skb
net: wimax/i2400m: fix NULL-deref at probe
isdn/gigaset: fix NULL-deref at probe
...
|
|
git://anongit.freedesktop.org/git/drm-intel into drm-fixes
drm/i915 fixes for v4.11-rc3
* tag 'drm-intel-fixes-2017-03-14' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: Fix forcewake active domain tracking
drm/i915: Nuke skl_update_plane debug message from the pipe update critical section
drm/i915: use correct node for handling cache domain eviction
drm/i915: Drain the freed state from the tail of the next commit
drm/i915: Nuke debug messages from the pipe update critical section
drm/i915: Use pagecache write to prepopulate shmemfs from pwrite-ioctl
drm/i915: Store a permanent error in obj->mm.pages
drm/i915: Move updating color management to before vblank evasion
drm/i915/gen9: Increase PCODE request timeout to 50ms
drm/i915: Avoid tweaking evaluation thresholds on Baytrail v3
drm/i915: Remove the vma from the drm_mm if binding fails
drm/i915/fbdev: Stop repeating tile configuration on stagnation
drm/i915/glk: Fix watermark computations for third sprite plane
drm/i915: Squelch any ktime/jiffie rounding errors for wait-ioctl
|
|
into drm-fixes
* 'for-upstream/malidp-fixes' of git://linux-arm.org/linux-ld:
drm: mali-dp: Fix smart layer not going to composition
drm: mali-dp: Remove mclk rate management
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux into drm-fixes
omapdrm fixes for v4.11
- Fix types in omapdrm uapi header to avoid userspace compilation errors
- Fix dmabuf mmap for dma_alloc'ed buffers
* tag 'omapdrm-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
uapi: fix drm/omap_drm.h userspace compilation errors
drm/omap: fix dmabuf mmap for dma_alloc'ed buffers
|
|
drm/tilcdc fixes for Linux v4.11
* tag 'tilcdc-4.11-fixes' of https://github.com/jsarha/linux:
drm/tilcdc: Set framebuffer DMA address to HW only if CRTC is enabled
drm/tilcdc: Fix hardcoded fail-return value in tilcdc_crtc_create()
|
|
The AMD ACP driver adds "-I../acp -I../acp/include" to the gcc command
line, which makes no sense, since these are evaluated relative to the
build directory. When we build with "make W=1", they instead cause
a warning:
cc1: error: ../acp/: No such file or directory [-Werror=missing-include-dirs]
cc1: error: ../acp/include: No such file or directory [-Werror=missing-include-dirs]
cc1: all warnings being treated as errors
../scripts/Makefile.build:289: recipe for target 'drivers/gpu/drm/amd/amdgpu/amdgpu_drv.o' failed
../scripts/Makefile.build:289: recipe for target 'drivers/gpu/drm/amd/amdgpu/amdgpu_device.o' failed
../scripts/Makefile.build:289: recipe for target 'drivers/gpu/drm/amd/amdgpu/amdgpu_kms.o' failed
This removes the subdir-ccflags variable that evidently did not
serve any purpose here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"Three libata fixes:
- fix for a circular reference bug in sysfs code which prevented
pata_legacy devices from being released after probe failure, which
in turn prevented devres from releasing the associated resources.
- drop spurious WARN in the command issue path which can be triggered
by a legitimate passthrough command.
- an ahci_qoriq specific fix"
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: correct the sata ecc setting error
libata: drop WARN from protocol error in ata_sff_qc_issue()
libata: transport: Remove circular dependency at free time
|
|
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca43 ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes: fc831825f99e ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23c0 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb50 ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd7a ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a454 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
raid1.c: fix a trivial typo in comments of freeze_array().
Cc: Jack Wang <jack.wang.usish@gmail.com>
Cc: Guoqing Jiang <gqjiang@suse.com>
Cc: John Stoffel <john@stoffel.org>
Acked-by: Coly Li <colyli@suse.de>
Signed-off-by: Zhilong Liu <zlliu@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Before this patch, device InJournal will be included in prexor
(SYNDROME_SRC_WANT_DRAIN) but not in reconstruct (SYNDROME_SRC_WRITTEN). So it
will break parity calculation. With srctype == SYNDROME_SRC_WRITTEN, we need
include both dev with non-null ->written and dev with R5_InJournal. This fixes
logic in 1e6d690(md/r5cache: caching phase of r5cache)
Cc: stable@vger.kernel.org (v4.10+)
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Commit 4e1f780032c5 ("mmc: block: break out mmc_blk_rw_cmd_abort()")
assumed the request had not completed, but in one case it had. Fix that.
Fixes: 4e1f780032c5 ("mmc: block: break out mmc_blk_rw_cmd_abort()")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit 15520111500c ("mmc: core: Further fix thread wake-up") allowed a
queue to release the host with is_waiting_last_req set to true. A queue
waiting to claim the host will not reset it, which can result in the
queue getting stuck in a loop.
Fixes: 15520111500c ("mmc: core: Further fix thread wake-up")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
HS400-ES devices fail to initialize with the following error messages.
mmc1: power class selection to bus width 8 ddr 0 failed
mmc1: error -110 whilst initialising MMC card
This was seen on Samsung Chromebook Plus. Code analysis points to
commit 3d4ef329757c ("mmc: core: fix multi-bit bus width without
high-speed mode"), which attempts to set the bus width for all but
HS200 devices unconditionally. However, for HS400-ES, the bus width
is already selected.
Cc: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Fixes: 3d4ef329757c ("mmc: core: fix multi-bit bus width ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Check that the sink really declared 12bpc support before we enable it.
This should not actually never happen since it's mandatory for HDMI
sinks to support 12bpc if they support any deep color modes. But
reality disagrees with the theory and there are actually sinks in
the wild that violate the spec.
v2: Fix the output_types check
Update commit message to state that these things are in fact real
Cc: stable@vger.kernel.org
Cc: Nicholas Sielicki <nicholas.sielicki@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99250
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170213175818.24958-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit c750bdd3e7e204cc88b32806c3864487a03cd84b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Fixes: e3ec3a3d11ad ("mmc: arasan: Add driver for Arasan SDHCI")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As i915_gem_reset_finish() undoes the steps from
i915_gem_reset_prepare() to leave the system in a fully-working state,
e.g. to be able to free the breadcrumb signal threads, make sure that we
always call it even on the error path.
Fixes: da9a796f5475 ("drm/i915: Split GEM resetting into 3 phases")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170212172002.23072-2-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit 8d613c539c74fa9055f88f4116196d7c820bd98f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Touching HW while clocks are off is a serious error and for instance
breaks suspend functionality. After this patch tilcdc_crtc_update_fb()
always updates the primary plane's framebuffer pointer, increases fb's
reference count and stores vblank event. tilcdc_crtc_update_fb() only
writes the fb's DMA address to HW if the crtc is enabled, as
tilcdc_crtc_enable() takes care of writing the address on enable.
This patch also refactors the tilcdc_crtc_update_fb() a bit. Number of
subsequent small changes had made it almost unreadable. There should
be no other functional changes but checking the CRTC's enable
state. However, the locking goes a bit differently and some of the
redundant checks have been removed in this new version.
The enable_lock should be enough to protect the access to
tilcdc_crtc->enabled. The irq_lock protects the access to last_vblank
and next_fb. The check for vrefresh and last_vblank being valid is
redundant, as the vrefresh should be always valid if the CRTC is
enabled and now last_vblank should be too, because it is initialized
to current time when CRTC raster is enabled. If for some reason the
values are not correctly initialized the division by zero warning is
quite appropriate.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Fix badly hardcoded return return value under fail-label. All goto
branches to the label set the "ret"-variable accordingly.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
|
|
On Baytrail, we manually calculate busyness over the evaluation interval
to avoid issues with miscaluations with RC6 enabled. However, it turns
out that the DOWN_EI interrupt generator is completely bust - it
operates in two modes, continuous or never. Neither of which are
conducive to good behaviour. Stop unmask the DOWN_EI interrupt and just
compute everything from the UP_EI which does seem to correspond to the
desired interval.
v2: Fixup gen6_rps_pm_mask() as well
v3: Inline vlv_c0_above() to combine the now identical elapsed
calculation for up/down and simplify the threshold testing
Fixes: 43cf3bf084ba ("drm/i915: Improved w/a for rps on Baytrail")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.1+
Link: http://patchwork.freedesktop.org/patch/msgid/20170309211232.28878-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170617.31564-1-chris@chris-wilson.co.uk
(cherry picked from commit e0e8c7cb6eb68e9256de2d8cbeb481d3701c05ac)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch makes the I915_PARAM_HAS_EXEC_CONSTANTS getparam return 0
(indicating the optional feature is not supported), and makes execbuf
always return -EINVAL if the flags are used.
Apparently, no userspace ever shipped which used this optional feature:
I checked the git history of Mesa, xf86-video-intel, libva, and Beignet,
and there were zero commits showing a use of these flags. Kernel commit
72bfa19c8deb4 apparently introduced the feature prematurely. According
to Chris, the intention was to use this in cairo-drm, but "the use was
broken for gen6", so I don't think it ever happened.
'relative_constants_mode' has always been tracked per-device, but this
has actually been wrong ever since hardware contexts were introduced, as
the INSTPM register is saved (and automatically restored) as part of the
render ring context. The software per-device value could therefore get
out of sync with the hardware per-context value. This meant that using
them is actually unsafe: a client which tried to use them could damage
the state of other clients, causing the GPU to interpret their BO
offsets as absolute pointers, leading to bogus memory reads.
These flags were also never ported to execlist mode, making them no-ops
on Gen9+ (which requires execlists), and Gen8 in the default mode.
On Gen8+, userspace can write these registers directly, achieving the
same effect. On Gen6-7.5, it likely makes sense to extend the command
parser to support them. I don't think anyone wants this on Gen4-5.
Based on a patch by Dave Gordon.
v3: Return -ENODEV for the getparam, as this is what we do for other
obsolete features. Suggested by Chris Wilson.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92448
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215093446.21291-1-kenneth@whitecape.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170433.26843-1-chris@chris-wilson.co.uk
(cherry picked from commit ef0f411f51475f4eebf9fc1b19a85be698af19ff)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
In order to prevent accessing the hpd registers outside of the display
power wells, we should refrain from writing to the registers before the
display interrupts are enabled.
[ 4.740136] WARNING: CPU: 1 PID: 221 at drivers/gpu/drm/i915/intel_uncore.c:795 __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740155] Unclaimed read from register 0x1e1110
[ 4.740168] Modules linked in: i915(+) intel_gtt drm_kms_helper prime_numbers
[ 4.740190] CPU: 1 PID: 221 Comm: systemd-udevd Not tainted 4.10.0-rc6+ #384
[ 4.740203] Hardware name: / , BIOS PYBSWCEL.86A.0027.2015.0507.1758 05/07/2015
[ 4.740220] Call Trace:
[ 4.740236] dump_stack+0x4d/0x6f
[ 4.740251] __warn+0xc1/0xe0
[ 4.740265] warn_slowpath_fmt+0x4a/0x50
[ 4.740281] ? insert_work+0x77/0xc0
[ 4.740355] ? fwtable_write32+0x90/0x130 [i915]
[ 4.740431] __unclaimed_reg_debug+0x44/0x50 [i915]
[ 4.740507] fwtable_read32+0xd8/0x130 [i915]
[ 4.740575] i915_hpd_irq_setup+0xa5/0x100 [i915]
[ 4.740649] intel_hpd_init+0x68/0x80 [i915]
[ 4.740716] i915_driver_load+0xe19/0x1380 [i915]
[ 4.740784] i915_pci_probe+0x32/0x90 [i915]
[ 4.740799] pci_device_probe+0x8b/0xf0
[ 4.740815] driver_probe_device+0x2b6/0x450
[ 4.740828] __driver_attach+0xda/0xe0
[ 4.740841] ? driver_probe_device+0x450/0x450
[ 4.740853] bus_for_each_dev+0x5b/0x90
[ 4.740865] driver_attach+0x19/0x20
[ 4.740878] bus_add_driver+0x166/0x260
[ 4.740892] driver_register+0x5b/0xd0
[ 4.740906] ? 0xffffffffa0166000
[ 4.740920] __pci_register_driver+0x47/0x50
[ 4.740985] i915_init+0x5c/0x5e [i915]
[ 4.740999] do_one_initcall+0x3e/0x160
[ 4.741015] ? __vunmap+0x7c/0xc0
[ 4.741029] ? kmem_cache_alloc+0xcf/0x120
[ 4.741045] do_init_module+0x55/0x1c4
[ 4.741060] load_module+0x1f3f/0x25b0
[ 4.741073] ? __symbol_put+0x40/0x40
[ 4.741086] ? kernel_read_file+0x100/0x190
[ 4.741100] SYSC_finit_module+0xbc/0xf0
[ 4.741112] SyS_finit_module+0x9/0x10
[ 4.741125] entry_SYSCALL_64_fastpath+0x17/0x98
[ 4.741135] RIP: 0033:0x7f8559a140f9
[ 4.741145] RSP: 002b:00007fff7509a3e8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 4.741161] RAX: ffffffffffffffda RBX: 00007f855aba02d1 RCX: 00007f8559a140f9
[ 4.741172] RDX: 0000000000000000 RSI: 000055b6db0914f0 RDI: 0000000000000011
[ 4.741183] RBP: 0000000000020000 R08: 0000000000000000 R09: 000000000000000e
[ 4.741193] R10: 0000000000000011 R11: 0000000000000246 R12: 000055b6db0854d0
[ 4.741204] R13: 000055b6db091150 R14: 0000000000000000 R15: 000055b6db035924
v2: Set dev_priv->display_irqs_enabled to true for all platforms other
than vlv/chv that manually control the display power domain.
Fixes: 19625e85c6ec ("drm/i915: Enable polling when we don't have hpd")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97798
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lyude <cpaul@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170215131547.5064-1-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313170231.18633-1-chris@chris-wilson.co.uk
(cherry picked from commit 262fd485ac6b476479f41f00bb104f6a1766ae66)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When we restart the engines, and we have active requests, a request on
the first engine may complete and queue a request to the second engine
before we try to restart the second engine. That queueing of the
request may race with the engine to restart, and so may corrupt the
current state. Disabling the engine->irq_tasklet prevents the two paths
from writing into ELSP simultaneously (and modifyin the execlists_port[]
at the same time).
Include fixup 1d309634bcf4 ("drm/i915: Kill the tasklet then disable")
Fixes: 821ed7df6e2a ("drm/i915: Update reset path to fix incomplete requests")
Testcase: igt/gem_exec_fence/await-hang
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170208143033.11651-3-chris@chris-wilson.co.uk
Link: http://patchwork.freedesktop.org/patch/msgid/20170313165958.13970-2-chris@chris-wilson.co.uk
(cherry picked from commit 1f7b847d72c3583df5048d83bd945d0c2c524c28)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
