| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_DRM_I2C_ADV7511 and CONFIG_VIDEO_ADV7511 bind to the same
platform device, so whichever driver gets loaded first will be used on
the device. So they shouldn't be enabled at the same time.
Rework so that VIDEO_ADV7511 and VIDEO_COBALT depends on
DRM_I2C_ADV7511=n or COMPILE_TEST.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
But this only really works if all drivers use this, so convert
this touchscreen driver accordingly.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Florian Echtler <floe@butterbrot.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Dynamically allocate clocks and move clock names out of struct
hantro_variant. This lifts the four clock limit and allows to use
ARRAY_SIZE() to fill .num_clocks to reduce the risk of mismatches.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
On i.MX8MQ/MM a separate control block contains registers for per-core
resets, clock gating, and fuse register control.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support for multiple register ranges with SoC specific names.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The i.MX8MQ bindings will use different IRQ names ("g1" instead of
"vdpu", and "g2"), so make them configurable. This also allows to
register more than two IRQs, which will be required for i.MX8MM support
later (it will add "h1" instead of "vepu").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
It seems that on i.MX8MQ the power domain controller does not propagate
resets to the VPU cores on resume. Add a callback to allow implementing
manual reset of the VPU cores after ungating the power domain.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
It can be helpful to know which video device was registered at which
device node.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Rename the driver and all relevant identifiers from Rockchip to Hantro,
as other Hantro IP based VPU implementations can be supported by the
same driver.
The RK3288 decoder is Hantro G1 based, the encoder is Hantro H1.
This patch just renames, no functional changes.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
With v5.2-rc1, The ftrace functions_graph tracer locks up whenever it is
enabled on arm64.
Since commit 0ea415390cd3 ("clocksource/arm_arch_timer: Use
arch_timer_read_counter to access stable counters") a function pointer
is consistently used to read the counter instead of potentially
referencing an inlinable function.
The graph tracers relies on accessing the timer counters to compute the
time spent in functions which causes the lockup when attempting to trace
these code paths.
Annotate the arm arch timer counter accessors as notrace.
Fixes: 0ea415390cd3 ("clocksource/arm_arch_timer: Use
arch_timer_read_counter to access stable counters")
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This converts the Wolfson Micro WM831x DCDC converter to use
a GPIO descriptor for the GPIO driving the DVS pin.
There is just one (non-DT) machine in the kernel using this, and
that is the Wolfson Micro (now Cirrus) Cragganmore 6410 so we
patch this board to pass a descriptor table and fix up the driver
accordingly.
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: patches@opensource.cirrus.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On buses like SlimBus and SoundWire which does not support
gather_writes yet in regmap, A bulk write on paged register
would be silently ignored after programming page.
This is because local variable 'ret' value in regmap_raw_write_impl()
gets reset to 0 once page register is written successfully and the
code below checks for 'ret' value to be -ENOTSUPP before linearising
the write buffer to send to bus->write().
Fix this by resetting the 'ret' value to -ENOTSUPP in cases where
gather_writes() is not supported or single register write is
not possible.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If an edge interrupt triggers while entering idle just before we save
GPIO datain register to saved_datain, the triggered GPIO will not be
noticed on wake-up. This is because the saved_datain and GPIO datain
are the same on wake-up in omap_gpio_unidle(). Let's fix this by
ignoring any pending edge interrupts for saved_datain.
This issue affects only idle states where the GPIO module internal
wake-up path is operational. For deeper idle states where the GPIO
module gets powered off, Linux generic wakeirqs must be used for
the padconf wake-up events with pinctrl-single driver. For examples,
please see "interrupts-extended" dts usage in many drivers.
This issue can be somewhat easily reproduced by pinging an idle system
with smsc911x Ethernet interface configured IRQ_TYPE_EDGE_FALLING. At
some point the smsc911x interrupts will just stop triggering. Also if
WLCORE WLAN is used with EDGE interrupt like it's documentation specifies,
we can see lost interrupts without this patch.
Note that in the long run we may be able to cancel entering idle by
returning an error in gpio_omap_cpu_notifier() on pending interrupts.
But let's fix the bug first.
Also note that because of the recent clean-up efforts this patch does
not apply directly to older kernels. This does fix a long term issue
though, and can be backported as needed.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The FMC subsystem was created in 2012 with the ambition to
drive development of drivers for this hardware upstream.
The current implementation has architectural flaws and would
need to be revamped using real hardware to something that can
reuse existing kernel abstractions in the subsystems for e.g.
I2C, FPGA and GPIO.
We have concluded that for the mainline kernel it will be
better to delete the subsystem and start over with a clean
slate when/if an active maintainer steps up.
For details see:
https://lkml.org/lkml/2018/10/29/534
Suggested-by: Federico Vaga <federico.vaga@cern.ch>
Cc: Pat Riehecky <riehecky@fnal.gov>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The devm_gpiod_request_gpiod() call will add "-gpios" to
any passed connection ID before looking it up.
I do not think the reset GPIO on this platform is named
"reset-gpios-gpios" but rather "reset-gpios" in the device
tree, so fix this up so that we get a proper reset GPIO
handle.
Also drop the inclusion of the legacy GPIO header.
Fixes: 0e8ce93bdceb ("i2c: pca-platform: add devicetree awareness")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When a device is authorized from userspace by writing to authorized
attribute we first take the domain lock and then runtime resume the
device in question. There are two issues with this.
First is that the device connected notifications are blocked during this
time which means we get them only after the authorization operation is
complete. Because of this the authorization needed flag from the
firmware notification is not reflecting the real authorization status
anymore. So what happens is that the "authorized" keeps returning 0 even
if the device was already authorized properly.
Second issue is that each time the controller is runtime resumed the
connection_id field of device connected notification may be different
than in the previous resume. We need to use the latest connection_id
otherwise the firmware rejects the authorization command.
Fix these by moving runtime resume operations to happen before the
domain lock is taken, and waiting for the updated device connected
notification from the firmware before we allow runtime resume of a
device to complete.
While there add missing locking to tb_switch_nvm_read().
Fixes: 09f11b6c99fe ("thunderbolt: Take domain lock in switch sysfs attribute callbacks")
Reported-by: Pengfei Xu <pengfei.xu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We've moved the override and firmware EDID (simply "override EDID" from
now on) handling to the low level drm_do_get_edid() function in order to
transparently use the override throughout the stack. The idea is that
you get the override EDID via the ->get_modes() hook.
Unfortunately, there are scenarios where the DDC probe in drm_get_edid()
called via ->get_modes() fails, although the preceding ->detect()
succeeds.
In the case reported by Paul Wise, the ->detect() hook,
intel_crt_detect(), relies on hotplug detect, bypassing the DDC. In the
case reported by Ilpo Järvinen, there is no ->detect() hook, which is
interpreted as connected. The subsequent DDC probe reached via
->get_modes() fails, and we don't even look at the override EDID,
resulting in no modes being added.
Because drm_get_edid() is used via ->detect() all over the place, we
can't trivially remove the DDC probe, as it leads to override EDID
effectively meaning connector forcing. The goal is that connector
forcing and override EDID remain orthogonal.
Generally, the underlying problem here is the conflation of ->detect()
and ->get_modes() via drm_get_edid(). The former should just detect, and
the latter should just get the modes, typically via reading the EDID. As
long as drm_get_edid() is used in ->detect(), it needs to retain the DDC
probe. Or such users need to have a separate DDC probe step first.
The EDID caching between ->detect() and ->get_modes() done by some
drivers is a further complication that prevents us from making
drm_do_get_edid() adapt to the two cases.
Work around the regression by falling back to a separate attempt at
getting the override EDID at drm_helper_probe_single_connector_modes()
level. With a working DDC and override EDID, it'll never be called; the
override EDID will come via ->get_modes(). There will still be a failing
DDC probe attempt in the cases that require the fallback.
v2:
- Call drm_connector_update_edid_property (Paul)
- Update commit message about EDID caching (Daniel)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107583
Reported-by: Paul Wise <pabs3@bonedaddy.net>
Cc: Paul Wise <pabs3@bonedaddy.net>
References: http://mid.mail-archive.com/alpine.DEB.2.20.1905262211270.24390@whs-18.cs.helsinki.fi
Reported-by: Ilpo Järvinen <ilpo.jarvinen@cs.helsinki.fi>
Cc: Ilpo Järvinen <ilpo.jarvinen@cs.helsinki.fi>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
References: 15f080f08d48 ("drm/edid: respect connector force for drm_get_edid ddc probe")
Fixes: 53fd40a90f3c ("drm: handle override and firmware EDID at drm_do_get_edid() level")
Cc: <stable@vger.kernel.org> # v4.15+ 56a2b7f2a39a drm/edid: abstract override/firmware EDID retrieval
Cc: <stable@vger.kernel.org> # v4.15+
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Harish Chegondi <harish.chegondi@intel.com>
Tested-by: Paul Wise <pabs3@bonedaddy.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190610093054.28445-1-jani.nikula@intel.com
|
|
The Acorn i2c driver (for RiscPC) triggers the "i2c adapter has no name"
warning in the I2C core driver, resulting in the RTC being inaccessible.
Fix this.
Fixes: 2236baa75f70 ("i2c: Sanity checks on adapter registration")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
|
|
Abstract the debugfs override and the firmware EDID retrieval
function. We'll be needing it in the follow-up. No functional changes.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Harish Chegondi <harish.chegondi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Tested-by: Paul Wise <pabs3@bonedaddy.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190607110513.12072-1-jani.nikula@intel.com
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The irq_startup() method returns an unsigned int, but in __irq_startup()
it is assigned to an int. However, nothing checks for errors, so any
error that is returned is ignored.
Remove the check for GPIO-input mode and the error return.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We must never alter the register tables; these are read-only as far
as the driver is concerned. Constify these tables.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use local variables to store the base iomem address and regs table
pointer like omap_gpio_init_context() does. Not only does this make
the function neater, it also avoids unnecessary reloads of the same
data multiple times.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a GPIO block has the set/clear dataout registers implemented, it
also has the normal dataout register implemented. Reading this register
reads the current GPIO output state, and writing it sets the GPIOs to
the explicit state. This is the behaviour that we want when saving and
restoring the context, so use the dataout register exclusively.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
omap_set_gpio_irqenable() calls two helpers that are almost the same
apart from whether they set or clear bits. We can consolidate these:
- in the set/clear bit register case, we can perform the operation on
our saved context copy and write the appropriate set/clear register.
- otherwise, we can use our read-modify-write helper and invert enable
if irqenable_inv is set.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This function open-codes an exclusive-or bitwise operation using an
if() statement and explicitly setting or clearing the bit. Instead,
use an exclusive-or operation instead, and simplify the function.
We can combine the preprocessor conditional using IS_ENABLED() and
gain some additional compilation coverage.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We already have a read-modify-write helper, but there's more that can
be done with a read-modify-write helper if it returned the new value.
Modify the existing helper to return the new value, and arrange for
it to take one less argument by having the caller compute the register
address.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
bank->level_mask is merely the bitwise or of the level detection
context which we have already read in this function. Rather than
repeating additional reads, compute it from the values already
read.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
One of the reasons for set_multiple() to exist is to allow multiple
GPIOs on the same chip to be changed simultaneously - see commit
5f42424354f5 ("gpiolib: allow simultaneous setting of multiple GPIO
outputs"):
- Simultaneous glitch-free setting of multiple pins on any kind of
parallel bus attached to GPIOs provided they all reside on the
same chip and bank.
In order for this to work, we should not use the atomic set/clear
registers, but instead read-modify-write the dataout register. We
already take the spinlock to ensure that happens atomically, so
move the code into the set_multiple() function and kill the two
helper functions.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There is no reason to have helper functions to read the datain and
dataout registers when they are only used in one location. Simplify
this code to make it more readable.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
omap_gpio_get() calls omap_get_gpio_datain() or omap_get_gpio_dataout()
to read the GPIO state. These two functions are only called from this
method, so they don't add much value. Move their contents into
omap_gpio_get() method and simplify.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Architectures are single-copy atomic, which means that simply reading
a register is an inherently atomic operation. There is no need to
take a spinlock here.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Move these two functions to live beside the rest of the gpio chip
implementation, rather than in the middle of the irq chip
implementation.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The irq_ack method does not fit our hardware requirements. Edge
interrupts must be cleared before we handle them, and level interrupts
must be cleared after handling them.
We handle the interrupt clearance in our interrupt handler for edge IRQs
and in the unmask method for level IRQs.
Replace the irq_ack method with the no-op method from the dummy irq
chip.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The edge interrupt handling was effectively:
isr = ISR_reg & enabled;
if (bank->level_mask)
level_mask = bank->level_mask & enabled;
else
level_mask = 0;
edge = isr & ~level_mask;
When bank->level_mask is zero, level_mask will be computed as zero
anyway, so the if() statement is redundant. We are then left with:
isr = ISR_reg & enabled;
level_mask = bank->level_mask & enabled;
edge = isr & ~level_mask;
This can be simplified further to:
isr = ISR_reg & enabled;
edge = isr & ~bank->level_mask;
since the second mask with 'enabled' is redundant.
Improve the associated comment as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit c4791bc6e3a6 ("gpio: omap: drop omap_gpio_list") removed the
list head and addition to the list head of each gpio bank, but failed
to remove the list_del() call and the node inside struct gpio_bank.
Remove these too.
Fixes: c4791bc6e3a6 ("gpio: omap: drop omap_gpio_list")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 384ebe1c2849 ("gpio/omap: Add DT support to GPIO driver") added
the register definition tables to the gpio-omap driver. Subsequently to
that commit, commit 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx()
checks from *_runtime_resume()") added definitions for irqstatus_raw*
registers to the legacy OMAP4 definitions, but missed the DT
definitions.
This causes an unintentional change of behaviour for the 1.101 errata
workaround on OMAP4 platforms. Fix this oversight.
Fixes: 4e962e8998cc ("gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Documentation states:
NOTE: There must be a correlation between the wake-up enable and
interrupt-enable registers. If a GPIO pin has a wake-up configured
on it, it must also have the corresponding interrupt enabled (on
one of the two interrupt lines).
Ensure that this condition is always satisfied by enabling the detection
events after enabling the interrupt, and disabling the detection before
disabling the interrupt. This ensures interrupt/wakeup events can not
happen until both the wakeup and interrupt enables correlate.
If we do any clearing, clear between the interrupt enable/disable and
trigger setting.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add devm_free_irq() call to mlxreg-hotplug remove() for clean release
of devices irq resource. Fix debugobjects warning triggered by rmmod
It prevents of use-after-free memory, related to
mlxreg_hotplug_work_handler.
Issue has been reported as debugobjects warning triggered by
'rmmod mlxtreg-hotplug' flow, while running kernel with
CONFIG_DEBUG_OBJECTS* options.
[ 2489.623551] ODEBUG: free active (active state 0) object type: work_struct hint: mlxreg_hotplug_work_handler+0x0/0x7f0 [mlxreg_hotplug]
[ 2489.637097] WARNING: CPU: 5 PID: 3924 at lib/debugobjects.c:328 debug_print_object+0xfe/0x180
[ 2489.637165] RIP: 0010:debug_print_object+0xfe/0x180
?
[ 2489.637214] Call Trace:
[ 2489.637225] __debug_check_no_obj_freed+0x25e/0x320
[ 2489.637231] kfree+0x82/0x110
[ 2489.637238] release_nodes+0x33c/0x4e0
[ 2489.637242] ? devres_remove_group+0x1b0/0x1b0
[ 2489.637247] device_release_driver_internal+0x146/0x270
[ 2489.637251] driver_detach+0x73/0xe0
[ 2489.637254] bus_remove_driver+0xa1/0x170
[ 2489.637261] __x64_sys_delete_module+0x29e/0x320
[ 2489.637265] ? __ia32_sys_delete_module+0x320/0x320
[ 2489.637268] ? blkcg_exit_queue+0x20/0x20
[ 2489.637273] ? task_work_run+0x7d/0x100
[ 2489.637278] ? exit_to_usermode_loop+0x5b/0xf0
[ 2489.637281] do_syscall_64+0x73/0x160
[ 2489.637287] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 2489.637290] RIP: 0033:0x7f95c3596fd7
The difference in release flow with and with no devm_free_irq is listed
below:
bus: 'platform': remove driver mlxreg-hotplug
mlxreg_hotplug_remove(start)
-> devm_free_irq (with new code)
mlxreg_hotplug_remove (end)
release_nodes (start)
mlxreg-hotplug: DEVRES REL devm_hwmon_release (8 bytes)
device: 'hwmon3': device_unregister
PM: Removing info for No Bus:hwmon3
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (88 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (6 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (5 bytes)
mlxreg-hotplug: DEVRES REL devm_irq_release (16 bytes) (no new code)
mlxreg-hotplug: DEVRES REL devm_kzalloc_release (1376 bytes)
------------[ cut here ]------------ (no new code):
ODEBUG: free active (active state 0) object type: work_struct hint: mlxreg_hotplug_work_handler
release_nodes(end)
driver: 'mlxreg-hotplug': driver_release
Fixes: 1f976f6978bf ("platform/x86: Move Mellanox platform hotplug driver to platform/mellanox")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Fix the issue found while running kernel with the option
CONFIG_DEBUG_TEST_DRIVER_REMOVE.
Driver 'mlx-platform' registers 'i2c_mlxcpld' device and then registers
few underlying 'i2c-mux-reg' devices:
priv->pdev_i2c = platform_device_register_simple("i2c_mlxcpld", nr,
NULL, 0);
...
for (i = 0; i < ARRAY_SIZE(mlxplat_mux_data); i++) {
priv->pdev_mux[i] = platform_device_register_resndata(
&mlxplat_dev->dev,
"i2c-mux-reg", i, NULL,
0, &mlxplat_mux_data[i],
sizeof(mlxplat_mux_data[i]));
But actual parent of "i2c-mux-reg" device is priv->pdev_i2c->dev and
not mlxplat_dev->dev.
Patch fixes parent device parameter in a call to
platform_device_register_resndata() for "i2c-mux-reg".
It solves the race during initialization flow while 'i2c_mlxcpld.1' is
removing after probe, while 'i2c-mux-reg.0' is still in probing flow:
'i2c_mlxcpld.1' flow: probe -> remove -> probe.
'i2c-mux-reg.0' flow: probe -> ...
[ 12:621096] Registering platform device 'i2c_mlxcpld.1'. Parent at platform
[ 12:621117] device: 'i2c_mlxcpld.1': device_add
[ 12:621155] bus: 'platform': add device i2c_mlxcpld.1
[ 12:621384] Registering platform device 'i2c-mux-reg.0'. Parent at mlxplat
[ 12:621395] device: 'i2c-mux-reg.0': device_add
[ 12:621425] bus: 'platform': add device i2c-mux-reg.0
[ 12:621806] Registering platform device 'i2c-mux-reg.1'. Parent at mlxplat
[ 12:621828] device: 'i2c-mux-reg.1': device_add
[ 12:621892] bus: 'platform': add device i2c-mux-reg.1
[ 12:621906] bus: 'platform': add driver i2c_mlxcpld
[ 12:621996] bus: 'platform': driver_probe_device: matched device i2c_mlxcpld.1 with driver i2c_mlxcpld
[ 12:622003] bus: 'platform': really_probe: probing driver i2c_mlxcpld with device i2c_mlxcpld.1
[ 12:622100] i2c_mlxcpld i2c_mlxcpld.1: no default pinctrl state
[ 12:622293] device: 'i2c-1': device_add
[ 12:627280] bus: 'i2c': add device i2c-1
[ 12:627692] device: 'i2c-1': device_add
[ 12.629639] bus: 'platform': add driver i2c-mux-reg
[ 12.629718] bus: 'platform': driver_probe_device: matched device i2c-mux-reg.0 with driver i2c-mux-reg
[ 12.629723] bus: 'platform': really_probe: probing driver i2c-mux-reg with device i2c-mux-reg.0
[ 12.629818] i2c-mux-reg i2c-mux-reg.0: no default pinctrl state
[ 12.629981] platform i2c-mux-reg.0: Driver i2c-mux-reg requests probe deferral
[ 12.629986] platform i2c-mux-reg.0: Added to deferred list
[ 12.629992] bus: 'platform': driver_probe_device: matched device i2c-mux-reg.1 with driver i2c-mux-reg
[ 12.629997] bus: 'platform': really_probe: probing driver i2c-mux-reg with device i2c-mux-reg.1
[ 12.630091] i2c-mux-reg i2c-mux-reg.1: no default pinctrl state
[ 12.630247] platform i2c-mux-reg.1: Driver i2c-mux-reg requests probe deferral
[ 12.630252] platform i2c-mux-reg.1: Added to deferred list
[ 12.640892] devices_kset: Moving i2c-mux-reg.0 to end of list
[ 12.640900] platform i2c-mux-reg.0: Retrying from deferred list
[ 12.640911] bus: 'platform': driver_probe_device: matched device i2c-mux-reg.0 with driver i2c-mux-reg
[ 12.640919] bus: 'platform': really_probe: probing driver i2c-mux-reg with device i2c-mux-reg.0
[ 12.640999] i2c-mux-reg i2c-mux-reg.0: no default pinctrl state
[ 12.641177] platform i2c-mux-reg.0: Driver i2c-mux-reg requests probe deferral
[ 12.641187] platform i2c-mux-reg.0: Added to deferred list
[ 12.641198] devices_kset: Moving i2c-mux-reg.1 to end of list
[ 12.641219] platform i2c-mux-reg.1: Retrying from deferred list
[ 12.641237] bus: 'platform': driver_probe_device: matched device i2c-mux-reg.1 with driver i2c-mux-reg
[ 12.641247] bus: 'platform': really_probe: probing driver i2c-mux-reg with device i2c-mux-reg.1
[ 12.641331] i2c-mux-reg i2c-mux-reg.1: no default pinctrl state
[ 12.641465] platform i2c-mux-reg.1: Driver i2c-mux-reg requests probe deferral
[ 12.641469] platform i2c-mux-reg.1: Added to deferred list
[ 12.646427] device: 'i2c-1': device_add
[ 12.646647] bus: 'i2c': add device i2c-1
[ 12.647104] device: 'i2c-1': device_add
[ 12.669231] devices_kset: Moving i2c-mux-reg.0 to end of list
[ 12.669240] platform i2c-mux-reg.0: Retrying from deferred list
[ 12.669258] bus: 'platform': driver_probe_device: matched device i2c-mux-reg.0 with driver i2c-mux-reg
[ 12.669263] bus: 'platform': really_probe: probing driver i2c-mux-reg with device i2c-mux-reg.0
[ 12.669343] i2c-mux-reg i2c-mux-reg.0: no default pinctrl state
[ 12.669585] device: 'i2c-2': device_add
[ 12.669795] bus: 'i2c': add device i2c-2
[ 12.670201] device: 'i2c-2': device_add
[ 12.671427] i2c i2c-1: Added multiplexed i2c bus 2
[ 12.671514] device: 'i2c-3': device_add
[ 12.671724] bus: 'i2c': add device i2c-3
[ 12.672136] device: 'i2c-3': device_add
[ 12.673378] i2c i2c-1: Added multiplexed i2c bus 3
[ 12.673472] device: 'i2c-4': device_add
[ 12.673676] bus: 'i2c': add device i2c-4
[ 12.674060] device: 'i2c-4': device_add
[ 12.675861] i2c i2c-1: Added multiplexed i2c bus 4
[ 12.675941] device: 'i2c-5': device_add
[ 12.676150] bus: 'i2c': add device i2c-5
[ 12.676550] device: 'i2c-5': device_add
[ 12.678103] i2c i2c-1: Added multiplexed i2c bus 5
[ 12.678193] device: 'i2c-6': device_add
[ 12.678395] bus: 'i2c': add device i2c-6
[ 12.678774] device: 'i2c-6': device_add
[ 12.679969] i2c i2c-1: Added multiplexed i2c bus 6
[ 12.680065] device: 'i2c-7': device_add
[ 12.680275] bus: 'i2c': add device i2c-7
[ 12.680913] device: 'i2c-7': device_add
[ 12.682506] i2c i2c-1: Added multiplexed i2c bus 7
[ 12.682600] device: 'i2c-8': device_add
[ 12.682808] bus: 'i2c': add device i2c-8
[ 12.683189] device: 'i2c-8': device_add
[ 12.683907] device: 'i2c-1': device_unregister
[ 12.683945] device: 'i2c-1': device_unregister
[ 12.684387] device: 'i2c-1': device_create_release
[ 12.684536] bus: 'i2c': remove device i2c-1
[ 12.686019] i2c i2c-8: Failed to create compatibility class link
[ 12.686086] ------------[ cut here ]------------
[ 12.686087] can't create symlink to mux device
[ 12.686224] Workqueue: events deferred_probe_work_func
[ 12.686135] WARNING: CPU: 7 PID: 436 at drivers/i2c/i2c-mux.c:416 i2c_mux_add_adapter+0x729/0x7d0 [i2c_mux]
[ 12.686232] RIP: 0010:i2c_mux_add_adapter+0x729/0x7d0 [i2c_mux]
[ 0x190/0x190 [i2c_mux]
[ 12.686300] ? i2c_mux_alloc+0xac/0x110 [i2c_mux]
[ 12.686306] ? i2c_mux_reg_set+0x200/0x200 [i2c_mux_reg]
[ 12.686313] i2c_mux_reg_probe+0x22c/0x731 [i2c_mux_reg]
[ 12.686322] ? i2c_mux_reg_deselect+0x60/0x60 [i2c_mux_reg]
[ 12.686346] platform_drv_probe+0xa8/0x110
[ 12.686351] really_probe+0x185/0x720
[ 12.686358] driver_probe_device+0xdf/0x1f0
...
[ 12.686522] i2c i2c-1: Added multiplexed i2c bus 8
[ 12.686621] device: 'i2c-9': device_add
[ 12.686626] kobject_add_internal failed for i2c-9 (error: -2 parent: i2c-1)
[ 12.694729] i2c-core: adapter 'i2c-1-mux (chan_id 8)': can't register device (-2)
[ 12.705726] i2c i2c-1: failed to add mux-adapter 8 as bus 9 (error=-2)
[ 12.714494] device: 'i2c-8': device_unregister
[ 12.714537] device: 'i2c-8': device_unregister
Fixes: 6613d18e9038 ("platform/x86: mlx-platform: Move module from arch/x86")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When a switch event, such as tablet mode/laptop mode or docked/undocked,
wakes a device make sure that the value of the swich is reported.
Without when a device is put in tablet mode from laptop mode when it is
suspended or vice versa the device will wake up but mode will be
incorrect.
Tested by suspending a device in laptop mode and putting it in tablet
mode, the device resumes and is in tablet mode. When suspending the
device in tablet mode and putting it in laptop mode the device resumes
and is in laptop mode.
Signed-off-by: Mathew King <mathewk@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
asus_nb_wmi
Commit 78f3ac76d9e5 ("platform/x86: asus-wmi: Tell the EC the OS will
handle the display off hotkey") causes the backlight to be permanently off
on various EeePC laptop models using the eeepc-wmi driver (Asus EeePC
1015BX, Asus EeePC 1025C).
The asus_wmi_set_devstate(ASUS_WMI_DEVID_BACKLIGHT, 2, NULL) call added
by that commit is made conditional in this commit and only enabled in
the quirk_entry structs in the asus-nb-wmi driver fixing the broken
display / backlight on various EeePC laptop models.
Cc: João Paulo Rechi Vita <jprvita@endlessm.com>
Fixes: 78f3ac76d9e5 ("platform/x86: asus-wmi: Tell the EC the OS will handle the display off hotkey")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The domain_init() and md_domain_init() do almost the same job.
Consolidate them to avoid duplication.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
[No functional changes]
1. Starting with commit df4f3c603aeb ("iommu/vt-d: Remove static identity
map code") there are no callers for iommu_prepare_rmrr_dev() but the
implementation of the function still exists, so remove it. Also, as a
ripple effect remove get_domain_for_dev() and iommu_prepare_identity_map()
because they aren't being used either.
2. Remove extra new line in couple of places.
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The drhd and device scope list should be iterated with the
iommu global lock held. Otherwise, a suspicious RCU usage
message will be displayed.
[ 3.695886] =============================
[ 3.695917] WARNING: suspicious RCU usage
[ 3.695950] 5.2.0-rc2+ #2467 Not tainted
[ 3.695981] -----------------------------
[ 3.696014] drivers/iommu/intel-iommu.c:4569 suspicious rcu_dereference_check() usage!
[ 3.696069]
other info that might help us debug this:
[ 3.696126]
rcu_scheduler_active = 2, debug_locks = 1
[ 3.696173] no locks held by swapper/0/1.
[ 3.696204]
stack backtrace:
[ 3.696241] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.2.0-rc2+ #2467
[ 3.696370] Call Trace:
[ 3.696404] dump_stack+0x85/0xcb
[ 3.696441] intel_iommu_init+0x128c/0x13ce
[ 3.696478] ? kmem_cache_free+0x16b/0x2c0
[ 3.696516] ? __fput+0x14b/0x270
[ 3.696550] ? __call_rcu+0xb7/0x300
[ 3.696583] ? get_max_files+0x10/0x10
[ 3.696631] ? set_debug_rodata+0x11/0x11
[ 3.696668] ? e820__memblock_setup+0x60/0x60
[ 3.696704] ? pci_iommu_init+0x16/0x3f
[ 3.696737] ? set_debug_rodata+0x11/0x11
[ 3.696770] pci_iommu_init+0x16/0x3f
[ 3.696805] do_one_initcall+0x5d/0x2e4
[ 3.696844] ? set_debug_rodata+0x11/0x11
[ 3.696880] ? rcu_read_lock_sched_held+0x6b/0x80
[ 3.696924] kernel_init_freeable+0x1f0/0x27c
[ 3.696961] ? rest_init+0x260/0x260
[ 3.696997] kernel_init+0xa/0x110
[ 3.697028] ret_from_fork+0x3a/0x50
Fixes: fa212a97f3a36 ("iommu/vt-d: Probe DMA-capable ACPI name space devices")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
We don't allow a device to be assigned to user level when it is locked
by any RMRR's. Hence, intel_iommu_attach_device() will return error if
a domain of type IOMMU_DOMAIN_UNMANAGED is about to attach to a device
locked by rmrr. But this doesn't apply to a domain of type other than
IOMMU_DOMAIN_UNMANAGED. This adds a check to fix this.
Fixes: fa954e6831789 ("iommu/vt-d: Delegate the dma domain to upper layer")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reported-and-tested-by: Qian Cai <cai@lca.pw>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The iommu driver will ignore some iommu units if there's no
device under its scope or those devices have been explicitly
set to bypass the DMA translation. Don't enable those iommu
units, otherwise the devices under its scope won't work.
Fixes: d8190dc638866 ("iommu/vt-d: Enable DMA remapping after rmrr mapped")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Otherwise, domain_get_iommu() will be broken.
Fixes: 942067f1b6b97 ("iommu/vt-d: Identify default domains replaced with private")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
If a device gets a right domain in add_device ops, it shouldn't
return error.
Fixes: 942067f1b6b97 ("iommu/vt-d: Identify default domains replaced with private")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
