| Age | Commit message (Collapse) | Author |
|---|
|
'struct i2c_algorithm' and 'struct virtio_device_id' are not modified in
this driver.
Constifying this structure moves some data to a read-only section, so
increase overall security, especially when the structure holds some
function pointers, which is the case for struct i2c_algorithm.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
6663 568 16 7247 1c4f drivers/i2c/busses/i2c-virtio.o
After:
=====
text data bss dec hex filename
6735 472 16 7223 1c37 drivers/i2c/busses/i2c-virtio.o
--
Compile tested only
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
rcar_i2c_probe() has priv->devtype operation, but handling (A) and (C)
in same place is more understandable ( (A) and (B) are independent).
(A) if (priv->devtype < I2C_RCAR_GEN3) {
...
}
(B) ...
(C) if (priv->devtype >= I2C_RCAR_GEN3) {
...
}
Let's merge it with if-else
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
To ensure code clarity and prevent potential errors, it's advisable
to employ the ';' as a statement separator, except when ',' are
intentionally used for specific purposes.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
While at it, no more special handling needed here, remove the goto
label "err:".
Signed-off-by: Rong Qianfeng <rongqianfeng@vivo.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
While at it, no need to save clk pointer, drop sclk from struct
em_i2c_device.
Signed-off-by: Rong Qianfeng <rongqianfeng@vivo.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Theobroma Systems Mule is an MCU that emulates a set of I2C devices,
among which an amc6821 and devices that are reachable through an I2C-mux.
The devices on the mux can be selected by writing the appropriate device
number to an I2C config register (amc6821 reg 0xff).
This driver is expected to be probed as a platform device with amc6821
as its parent i2c device.
Add support for the mule-i2c-mux platform driver. The amc6821 driver
support for the mux will be added in a later commit.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Farouk Bouabid <farouk.bouabid@cherry.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The smatch check warning is "buffer overflow 'npcm_i2caddr' 2 <= 9".
The original design supports 10 target addresses although only 2
addresses are required for current implementation.
Restore the npcm_i2caddr array length to fix the smatch warning.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202408130818.FgDP5uNm-lkp@intel.com/
Signed-off-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
devm_clk_get_optional() and clk_prepare_enable() can be replaced by the
helper function devm_clk_get_optional_enabled(). Let's simplify the code by
using devm_clk_get_optional_enabled() and avoid calling
clk_disable_unprepare().
Signed-off-by: Zhang Zekun <zhangzekun11@huawei.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
We have the same (*) PM ops in the PCI and platform drivers.
Instead, consolidate that PM ops under exported variable and
deduplicate them.
*)
With the subtle ACPI and P-Unit behaviour differences in PCI case.
But this is not a problem as for ACPI we need to take care of the
P-Unit semaphore anyway and calling PM ops for PCI makes sense as
it might provide specific operation regions in ACPI (however there
are no known devices on market that are using it with PCI enabled I2C).
Note, the clocks are not in use in the PCI case.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sanket Goswami <Sanket.Goswami@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Simplify checking for unsupported bus speeds and reporting errors by
factoring out the calculation of the maximum bus speed, and by using the
dev_err_probe() helper.
While at it, use "%u" for u32, and improve the error message.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Tested-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Commit 90312351fd1e ("i2c: designware: MASTER mode as separated driver")
introduced ->disable() callback but there is no real use for it. Both
i2c-designware-master.c and i2c-designware-slave.c set it to the same
i2c_dw_disable() and scope is inside the same kernel module.
That said, replace the callback by explicitly calling the i2c_dw_disable().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Reduce scope of the I²C DesignWare driver exports to I2C_DW namespaces.
This will prevent abuse of the symbols and clean up global namespace.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Instead of asymmetrical checks for the firmware type use
the is_*_node() calls.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
We have the same code flows in the PCI and platform drivers. Moreover,
the flow requires the common code to export a few functions. Instead,
consolidate that flow under new function called
i2c_dw_fw_parse_and_configure() and drop unneeded exports.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
For the sake of consistency, rename dw_i2c_of_configure() and change
its parameter to be aligned with the i2c_dw_acpi_configure().
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Fast mode plus is available on most of the IP variants that RIIC driver
is working with. The exception is (according to HW manuals of the SoCs
where this IP is available) the Renesas RZ/A1H. For this, patch
introduces the struct riic_of_data::fast_mode_plus.
Fast mode plus was tested on RZ/G3S, RZ/G2{L,UL,LC}, RZ/Five by
instantiating the RIIC frequency to 1MHz and issuing i2c reads on the
fast mode plus capable devices (and the i2c clock frequency was checked on
RZ/G3S).
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Define individual arrays to describe the register offsets. In this way
we can describe different IP variants that share the same register offsets
but have differences in other characteristics. Commit prepares for the
addition of fast mode plus.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add suspend/resume support for the RIIC driver. This is necessary for the
Renesas RZ/G3S SoC which support suspend to deep sleep state where power
to most of the SoC components is turned off. As a result the I2C controller
needs to be reconfigured after suspend/resume. For this, the reset line
was stored in the driver private data structure as well as i2c timings.
The reset line and I2C timings are necessary to re-initialize the
controller after resume.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Enable runtime PM autosuspend support for the RIIC driver. With this, in
case there are consecutive xfer requests the device wouldn't be runtime
enabled/disabled after each consecutive xfer but after the
the delay configured by user. With this, we can avoid touching hardware
registers involved in runtime PM suspend/resume saving in this way some
cycles. The default chosen autosuspend delay is zero to keep the
previous driver behavior.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
pm_runtime_get_sync() may return with error. In case it returns with error
dev->power.usage_count needs to be decremented. pm_runtime_resume_and_get()
takes care of this. Thus use it.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
There is no need to runtime resume the device as long as the IP registers
are not accessed. Calling pm_runtime_get_sync() at the register access
time leads to a simpler error path.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Use a temporary variable for the struct device pointers to avoid
dereferencing.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
dw_i2c_of_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
i2c_dw_acpi_configure() is called without checking of the returned
value, hence just drop it by converting to void.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
There is no need to have ugly ifdeffery and additional macros
for the device ID tables. Always provide them. Since we touch
the ACPI table, make it sorted by ID.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Make the terminator entry look the same in all device ID tables.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add missing 'c' into i2c_designware_pci_ids variable name.
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
PCI core, after pcim_enable_device(), takes care about the allocated
IRQ vectors, no need to do it explicitly and break the cleaning up
order.
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Replace a while-loop by for-loop in i2c_dw_probe_lock_support() to
save a few lines of code.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Refactor the code by using goto statements to reduce duplication
and make the exit path clearer.
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Replace SET_RUNTIME_PM_OPS() with its modern RUNTIME_PM_OPS()
alternative.
The combined usage of pm_ptr() and RUNTIME_PM_OPS() allows the
compiler to evaluate if the runtime suspend/resume() functions
are used at build time or are simply dead code.
This allows removing the __maybe_unused notation from the runtime
suspend/resume() functions.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
In the mtk_i2c_irq() handler, variable restart_flag is initialized
to zero and then reassigned with I2C_RS_TRANSFER if and only if
auto_restart is enabled.
Avoid a double initialization of this variable by transferring the
auto_restart check to the restart_flag declaration.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Delimiters are meant to be last, no need for a ',' there. Remove a
superfluous newline in the ali1535 driver while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
When disabling CONFIG_X86_AMD_PLATFORM_DEVICE option, the driver
'drivers/acpi/acpi_apd.c' won't be compiled. This leads to a situation
where BMC (Baseboard Management Controller) cannot retrieve the memory
temperature via the i2c interface after i2c DW driver is loaded. Note
that BMC can retrieve the memory temperature before booting into OS.
[Debugging Detail]
1. dev->pclk and dev->clk are NULL when calling devm_clk_get_optional()
in dw_i2c_plat_probe().
2. The callings of i2c_dw_scl_hcnt() in i2c_dw_set_timings_master()
return 65528 (-8 in integer format) or 65533 (-3 in integer format).
The following log shows SS's HCNT/LCNT:
i2c_designware AMDI0010:01: Standard Mode HCNT:LCNT = 65533:65535
3. The callings of i2c_dw_scl_lcnt() in i2c_dw_set_timings_master()
return 65535 (-1 in integer format). The following log shows SS's
HCNT/LCNT:
i2c_designware AMDI0010:01: Fast Mode HCNT:LCNT = 65533:65535
4. i2c_dw_init_master() configures the register IC_SS_SCL_HCNT with
the value 65533. However, the DW i2c databook mentioned the value
cannot be higher than 65525. Quote from the DW i2c databook:
NOTE: This register must not be programmed to a value higher than
65525, because DW_apb_i2c uses a 16-bit counter to flag an
I2C bus idle condition when this counter reaches a value of
IC_SS_SCL_HCNT + 10.
5. Since ss_hcnt, ss_lcnt, fs_hcnt, and fs_lcnt are the invalid
values, we should not write the corresponding registers.
Fix the issue by reading dev->{ss,fs,hs}_hcnt and dev->{ss,fs,hs}_lcnt
from HW registers if ic_clk is not set.
Reported-by: Dong Wang <wangdong28@lenovo.com>
Suggested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Adrian Huang <ahuang12@lenovo.com>
Tested-by: Dong Wang <wangdong28@lenovo.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/linux-i2c/8295cbe1-a7c5-4a35-a189-5d0bff51ede6@linux.intel.com/
|
|
When -Wunused-const-variable is enabled (not the default),
there is a warning about two definitions in this file:
In file included from drivers/clk/rockchip/clk-rk3576.c:14:
drivers/clk/rockchip/clk-rk3576.c:334:7: error: 'mclk_pdm0_p' defined but not used [-Werror=unused-const-variable=]
334 | PNAME(mclk_pdm0_p) = { "mclk_pdm0_src_top", "xin24m" };
| ^~~~~~~~~~~
drivers/clk/rockchip/clk.h:564:43: note: in definition of macro 'PNAME'
564 | #define PNAME(x) static const char *const x[] __initconst
| ^
drivers/clk/rockchip/clk-rk3576.c:333:7: error: 'pdm0_p' defined but not used [-Werror=unused-const-variable=]
333 | PNAME(pdm0_p) = { "clk_pdm0_src_top", "xin24m" };
| ^~~~~~
drivers/clk/rockchip/clk.h:564:43: note: in definition of macro 'PNAME'
564 | #define PNAME(x) static const char *const x[] __initconst
| ^
Remove them for the moment. If they are needed later, they can
be added back at that point.
Fixes: cc40f5baa91b ("clk: rockchip: Add clock controller for the RK3576")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240909121116.254036-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In zonda_pll_adjust_l_val() replace the divide operator with comparison
operator to fix below build error and smatch warning.
drivers/clk/qcom/clk-alpha-pll.o: In function `clk_zonda_pll_set_rate':
clk-alpha-pll.c:(.text+0x45dc): undefined reference to `__aeabi_uldivmod'
smatch warnings:
drivers/clk/qcom/clk-alpha-pll.c:2129 zonda_pll_adjust_l_val() warn: replace
divide condition '(remainder * 2) / prate' with '(remainder * 2) >= prate'
Fixes: f4973130d255 ("clk: qcom: clk-alpha-pll: Update set_rate for Zonda PLL")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202408110724.8pqbpDiD-lkp@intel.com/
Signed-off-by: Satya Priya Kakitapalli <quic_skakitap@quicinc.com>
Link: https://lore.kernel.org/r/20240906113905.641336-1-quic_skakitap@quicinc.com
Reviewed-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Tell hardware to write back completed descriptors even when interrupts
are disabled. Otherwise, descriptors might not be written back until
the hardware can flush a full cacheline of descriptors. This can cause
unnecessary delays when traffic is light (or even trigger Tx queue
timeout).
The example scenario to reproduce the Tx timeout if the fix is not
applied:
- configure at least 2 Tx queues to be assigned to the same q_vector,
- generate a huge Tx traffic on the first Tx queue
- try to send a few packets using the second Tx queue.
In such a case Tx timeout will appear on the second Tx queue because no
completion descriptors are written back for that queue while interrupts
are disabled due to NAPI polling.
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll")
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Co-developed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
netif_txq_maybe_stop() returns -1, 0, or 1, while
idpf_tx_maybe_stop_common() says it returns 0 or -EBUSY. As a result,
there sometimes are Tx queue timeout warnings despite that the queue
is empty or there is at least enough space to restart it.
Make idpf_tx_maybe_stop_common() inline and returning true or false,
handling the return of netif_txq_maybe_stop() properly. Use a correct
goto in idpf_tx_maybe_stop_splitq() to avoid stopping the queue or
incrementing the stops counter twice.
Fixes: 6818c4d5b3c2 ("idpf: add splitq start_xmit")
Fixes: a5ab9ee0df0b ("idpf: add singleq start_xmit and napi poll")
Cc: stable@vger.kernel.org # 6.7+
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a mechanism to guard against stashing partial packets into the hash
table to make the driver more robust, with more efficient decision
making when cleaning.
Don't stash partial packets. This can happen when an RE (Report Event)
completion is received in flow scheduling mode, or when an out of order
RS (Report Status) completion is received. The first buffer with the skb
is stashed, but some or all of its frags are not because the stack is
out of reserve buffers. This leaves the ring in a weird state since
the frags are still on the ring.
Use the field libeth_sqe::nr_frags to track the number of
fragments/tx_bufs representing the packet. The clean routines check to
make sure there are enough reserve buffers on the stack before stashing
any part of the packet. If there are not, next_to_clean is left pointing
to the first buffer of the packet that failed to be stashed. This leaves
the whole packet on the ring, and the next time around, cleaning will
start from this packet.
An RS completion is still expected for this packet in either case. So
instead of being cleaned from the hash table, it will be cleaned from
the ring directly. This should all still be fine since the DESC_UNUSED
and BUFS_UNUSED will reflect the state of the ring. If we ever fall
below the thresholds, the TxQ will still be stopped, giving the
completion queue time to catch up. This may lead to stopping the queue
more frequently, but it guarantees the Tx ring will always be in a good
state.
Also, always use the idpf_tx_splitq_clean function to clean descriptors,
i.e. use it from clean_buf_ring as well. This way we avoid duplicating
the logic and make sure we're using the same reserve buffers guard rail.
This does require a switch from the s16 next_to_clean overflow
descriptor ring wrap calculation to u16 and the normal ring size check.
Signed-off-by: Joshua Hay <joshua.a.hay@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
&idpf_tx_buffer is almost identical to the previous generations, as well
as the way it's handled. Moreover, relying on dma_unmap_addr() and
!!buf->skb instead of explicit defining of buffer's type was never good.
Use the newly added libeth helpers to do it properly and reduce the
copy-paste around the Tx code.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
'struct regulator_desc' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
4974 736 16 5726 165e drivers/regulator/tps6287x-regulator.o
After:
=====
text data bss dec hex filename
5294 416 16 5726 165e drivers/regulator/tps6287x-regulator.o
--
Compile tested only
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/7727e493490d37775a653905dfe0cc1d8478f8e0.1725908163.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'struct regulator_desc' is not modified in this driver.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
On a x86_64, with allmodconfig:
Before:
======
text data bss dec hex filename
4419 2512 0 6931 1b13 drivers/regulator/wm8400-regulator.o
After:
=====
text data bss dec hex filename
6307 624 0 6931 1b13 drivers/regulator/wm8400-regulator.o
--
Compile tested only
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://patch.msgid.link/fde33ecfd9bbdbdc1da1620c9f3b1b7a72f9d805.1725906876.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently, trying to set the bridge mode attribute when numvfs=0 leads to a
crash:
bridge link set dev eth2 hwmode vepa
[ 168.967392] BUG: kernel NULL pointer dereference, address: 0000000000000030
[...]
[ 168.969989] RIP: 0010:mlx5_add_flow_rules+0x1f/0x300 [mlx5_core]
[...]
[ 168.976037] Call Trace:
[ 168.976188] <TASK>
[ 168.978620] _mlx5_eswitch_set_vepa_locked+0x113/0x230 [mlx5_core]
[ 168.979074] mlx5_eswitch_set_vepa+0x7f/0xa0 [mlx5_core]
[ 168.979471] rtnl_bridge_setlink+0xe9/0x1f0
[ 168.979714] rtnetlink_rcv_msg+0x159/0x400
[ 168.980451] netlink_rcv_skb+0x54/0x100
[ 168.980675] netlink_unicast+0x241/0x360
[ 168.980918] netlink_sendmsg+0x1f6/0x430
[ 168.981162] ____sys_sendmsg+0x3bb/0x3f0
[ 168.982155] ___sys_sendmsg+0x88/0xd0
[ 168.985036] __sys_sendmsg+0x59/0xa0
[ 168.985477] do_syscall_64+0x79/0x150
[ 168.987273] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[ 168.987773] RIP: 0033:0x7f8f7950f917
(esw->fdb_table.legacy.vepa_fdb is null)
The bridge mode is only relevant when there are multiple functions per
port. Therefore, prevent setting and getting this setting when there are no
VFs.
Note that after this change, there are no settings to change on the PF
interface using `bridge link` when there are no VFs, so the interface no
longer appears in the `bridge link` output.
Fixes: 4b89251de024 ("net/mlx5: Support ndo bridge_setlink and getlink")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Before creating a scheduling element in a NIC or E-Switch scheduler,
ensure that the requested element type is supported. If the element is
of type Transmit Scheduling Arbiter (TSAR), also verify that the
specific TSAR type is supported.
Fixes: 214baf22870c ("net/mlx5e: Support HTB offload")
Fixes: 85c5f7c9200e ("net/mlx5: E-switch, Create QoS on demand")
Fixes: 0fe132eac38c ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Ensure the scheduling element type and TSAR type are explicitly
initialized in the QoS rate group creation.
This prevents potential issues due to default values.
Fixes: 1ae258f8b343 ("net/mlx5: E-switch, Introduce rate limiting groups API")
Signed-off-by: Carolina Jubran <cjubran@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add MLX5E_400GAUI_8_400GBASE_CR8 to the extended modes
in ptys2ext_ethtool_table, since it was missing.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add MLX5E_1000BASE_T and MLX5E_100BASE_TX to the legacy
modes in ptys2legacy_ethtool_table, since they were missing.
Fixes: 665bc53969d7 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Shahar Shitrit <shshitrit@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Carolina Jubran <cjubran@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add the upcoming ConnectX-9 device ID to the table of supported
PCI device IDs.
Fixes: f908a35b2218 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In testing Dynamic Capacity Device (DCD) support, a lockdep splat
revealed an ABBA issue between the memory notifiers and the DCD extent
processing code.[0] Changing the lock ordering within DCD proved
difficult because regions must be stable while searching for the proper
region and then the device lock must be held to properly notify the DAX
region driver of memory changes.
Dan points out in the thread that notifiers should be able to trust that
it is safe to access static data. Region data is static once the device
is realized and until it's destruction. Thus it is better to manage the
notifiers within the region driver.
Remove the need for a lock by ensuring the notifiers are active only
during the region's lifetime.
Furthermore, remove cxl_region_nid() because resource can't be NULL
while the region is stable.
Link: https://lore.kernel.org/all/66b4cf539a79b_a36e829416@iweiny-mobl.notmuch/ [0]
Cc: Ying Huang <ying.huang@intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/20240904-fix-notifiers-v3-1-576b4e950266@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
|
Cases can be divided into two categories which are DVSEC range enabled and
not enabled when HDM decoders exist but is not enabled. To avoid checking
info->mem_enabled, which indicates the enablement of DVSEC range, every
time, we can check !info->mem_enabled once in advance. This simplification
can make the code clearer.
No functional change intended.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yanfei Xu <yanfei.xu@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Link: https://patch.msgid.link/20240828084231.1378789-5-yanfei.xu@intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
|
