| Age | Commit message (Collapse) | Author |
|---|
|
Use direct mapping to read the flash device contents. This operation
mode is called "Command mode" on Aspeed SoC SMC controllers. It uses a
Control Register for the settings to apply when a memory operation is
performed on the flash device mapping window.
If the window is not big enough, fall back to the "User mode" to
perform the read.
Direct mapping for writes will come later when validated.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-5-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ERROR check is already in clk_disable() and clk_unprepare() by using
IS_ERR_OR_NULL. Remove unneeded ERROR check for ftide->pclk here.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
When calling dev_fill_forward_path on a pppoe device, the provided destination
address is invalid. In order for the bridge fdb lookup to succeed, the pppoe
code needs to update ctx->daddr to the correct value.
Fix this by storing the address inside struct net_device_path_ctx
Fixes: f6efc675c9dd ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-05-14
this is a pull request of 2 patches for net/master.
Changes to linux-can-fixes-for-5.18-20220513:
- adjusted Fixes: Tag on "Revert "can: m_can: pci: use custom bit timings for Elkhart Lake""
(Thanks Jakub)
Both patches are by Jarkko Nikula, target the m_can PCI driver
bindings, and fix usage of wrong bit timing constants for the Elkhart
Lake platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 2 ways an engine can get reset in i915 and the method of reset
affects how KMD labels a context as guilty/innocent.
(1) GuC initiated engine-reset: GuC resets a hung engine and notifies
KMD. The context that hung on the engine is marked guilty and all other
contexts are innocent. The innocent contexts are resubmitted.
(2) GT based reset: When an engine heartbeat fails to tick, KMD
initiates a gt/chip reset. All active contexts are marked as guilty and
discarded.
In order to correctly mark the contexts as guilty/innocent, pass a mask
of engines that were reset to __guc_reset_context.
Fixes: eb5e7da736f3 ("drm/i915/guc: Reset implementation for new GuC interface")
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426003045.3929439-1-umesh.nerlige.ramappa@intel.com
(cherry picked from commit 303760aa914b7f5ac9602dbb4b471a2ad52eeb3e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Bspec has added some steps that check forDMC MMIO range before
programming them
v2: Fix for CI
v3: move register defines to .h (Anusha)
- Check MMIO restrictions per pipe
- Add MMIO restricton for v1 dmc header as well (Lucas)
v4: s/_PICK/_PICK_EVEN and use it only for Pipe DMC scenario.
- clean up sanity check logic.(Lucas)
- Add MMIO range for RKL as well.(Anusha)
v5: Use DISPLAY_VER instead of per platform check (Lucas)
BSpec: 49193
Cc: stable@vger.kernel.org
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511000847.1068302-1-anusha.srivatsa@intel.com
(cherry picked from commit 21c47196aec3a93f913a7515e1e7b30e6c54d6c6)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
The RDAMA and TCP transport both complete the timed out request in the
same manner and hence code is duplicated. Add and use the helper
nvmf_complete_timed_out_request() to remove the duplicate code.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
On our ZynqMP system we observe, that a NVMe drive that resets itself
while doing a firmware update causes a Kernel crash like this:
[ 67.720772] pcieport 0000:02:02.0: pciehp: Slot(2): Link Down
[ 67.720783] pcieport 0000:02:02.0: pciehp: Slot(2): Card not present
[ 67.720795] nvme 0000:04:00.0: PME# disabled
[ 67.720849] Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP
[ 67.720853] nwl-pcie fd0e0000.pcie: Slave error
Analysis: When nvme_dev_disable() is called because of this PCIe hotplug
event, pci_is_enabled() is still true. And accessing the NVMe drive
which is currently not available as it's in reboot process causes this
"synchronous external abort" on this ARM64 platform.
This patch adds the pci_device_is_present() check as well, which returns
false in this "Card not present" hot-plug case. With this change, the
NVMe driver does not try to access the NVMe registers any more and the
FW update finishes without any problems.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In nvme_alloc_admin_tags, the admin_q can be set to an error (typically
-ENOMEM) if the blk_mq_init_queue call fails to set up the queue, which
is checked immediately after the call. However, when we return the error
message up the stack, to nvme_reset_work the error takes us to
nvme_remove_dead_ctrl()
nvme_dev_disable()
nvme_suspend_queue(&dev->queues[0]).
Here, we only check that the admin_q is non-NULL, rather than not
an error or NULL, and begin quiescing a queue that never existed, leading
to bad / NULL pointer dereference.
Signed-off-by: Kyle Smith <kyles@hpe.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Most of the internal passthru commands use __nvme_submit_sync_cmd()
interface. There are few places we open code the request submission :-
1. nvme_keep_alive_work(struct work_struct *work)
2. nvme_timeout(struct request *req, bool reserved)
3. nvme_delete_queue(struct nvme_queue *nvmeq, u8 opcode)
Mark the internal passthru request quiet so that we can skip the verbose
error message from nvme_log_error() in nvme_end_req() completion path,
this will be consistent with what we have in __nvme_submit_sync_cmd().
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
No usage of blkdev.h elements.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Log a few more path related status codes.
Signed-off-by: Max Gurtovoy <mgurtovoy@nvidia.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The nvme specification only requires qword alignment for segment
descriptors, and the driver already guarantees that. The spec has always
allowed user data to be dword aligned, which is what the queue's
attribute is for, so relax the alignment requirement to that value.
While we could allow byte alignment for some controllers when using
SGLs, we still need to support PRP, and that only allows dword.
Fixes: 3b2a1ebceba3 ("nvme: set dma alignment to qword")
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
DMRSLl is in the unit of logical blocks, while max_discard_sectors is
in the unit of "linux sector".
Signed-off-by: Tom Yan <tom.ty89@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The TODO list in drivers/cdrom/cdrom.c has a single entry containing
obsolete information, unchanged since the first git commit over 17 years
ago, and probably longer. Remove this list from the comment to prevent
confusion in future.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220515205833.944139-6-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The last traces of the IDE driver went away in commit b7fb14d3ac63
("ide: remove the legacy ide driver") but it left behind some traces
of old documentation.
As luck would have it Randy and I would submit similar changes within
a week of each other to address this. As Randy's commit is in the doc
tree already - this delta is just the stuff my removal contained that
was not in Randy's IDE doc removal.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Phillip Potter <phil@philpotter.co.uk>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: https://lore.kernel.org/all/20220427165917.GE12977@windriver.com
[phil@philpotter.co.uk: removed diffs already added by others]
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220515205833.944139-5-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This was only used by the ide-cd driver, which went away in
commit b7fb14d3ac63 ("ide: remove the legacy ide driver")
so we might as well take advantage of that and get rid of
this hook as well.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Phillip Potter <phil@philpotter.co.uk>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: https://lore.kernel.org/all/20220427132436.12795-2-paul.gortmaker@windriver.com
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220515205833.944139-3-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently, some EXPORT_SYMBOL declarations do not follow the exported
function, which affects the readability of the code. To maintain
consistency, move these EXPORT_SYMBOL declarations to the correct
position to improve the readability of the code.
Signed-off-by: Enze Li <lienze@kylinos.cn>
Link: https://lore.kernel.org/all/20220406090337.1116708-1-lienze@kylinos.cn
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220515205833.944139-2-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There are no code changes here; this is just a reordering of functions,
so that in subsequent commits, the timer entropy functions can call into
the interrupt ones.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
When a kernel is built with CONFIG_ARM64_PSEUDO_NMI=y and pseudo-NMIs
are enabled at runtime, GICv3's gic_handle_irq() can leave DAIF and
ICC_PMR_EL1 in an unexpected state in some cases, breaking subsequent
usage of local_irq_enable() and resulting in softirqs being run with
IRQs erroneously masked (possibly resulting in deadlocks).
This can happen when an IRQ exception is taken from a context where
regular IRQs were unmasked, and either:
(1) ICC_IAR1_EL1 indicates a special INTID (e.g. as a result of an IRQ
being withdrawn since the IRQ exception was taken).
(2) ICC_IAR1_EL1 and ICC_RPR_EL1 indicate an NMI was acknowledged.
When an NMI is taken from a context where regular IRQs were masked,
there is no problem.
When CONFIG_ARM64_DEBUG_PRIORITY_MASKING=y, this can be detected with
perf, e.g.
| # ./perf record -a -g -e cycles:k ls -alR / > /dev/null 2>&1
| ------------[ cut here ]------------
| WARNING: CPU: 0 PID: 14 at arch/arm64/include/asm/irqflags.h:32 arch_local_irq_enable+0x4c/0x6c
| Modules linked in:
| CPU: 0 PID: 14 Comm: ksoftirqd/0 Not tainted 5.18.0-rc5-00004-g876c38e3d20b #12
| Hardware name: linux,dummy-virt (DT)
| pstate: 204000c5 (nzCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : arch_local_irq_enable+0x4c/0x6c
| lr : __do_softirq+0x110/0x5d8
| sp : ffff8000080bbbc0
| pmr_save: 000000f0
| x29: ffff8000080bbbc0 x28: ffff316ac3a6ca40 x27: 0000000000000000
| x26: 0000000000000000 x25: ffffa04611c06008 x24: ffffa04611c06008
| x23: 0000000040400005 x22: 0000000000000200 x21: ffff8000080bbe20
| x20: ffffa0460fe10320 x19: 0000000000000009 x18: 0000000000000000
| x17: ffff91252dfa9000 x16: ffff800008004000 x15: 0000000000004000
| x14: 0000000000000028 x13: ffffa0460fe17578 x12: ffffa0460fed4294
| x11: ffffa0460fedc168 x10: ffffffffffffff80 x9 : ffffa0460fe10a70
| x8 : ffffa0460fedc168 x7 : 000000000000b762 x6 : 00000000057c3bdf
| x5 : ffff8000080bbb18 x4 : 0000000000000000 x3 : 0000000000000001
| x2 : ffff91252dfa9000 x1 : 0000000000000060 x0 : 00000000000000f0
| Call trace:
| arch_local_irq_enable+0x4c/0x6c
| __irq_exit_rcu+0x180/0x1ac
| irq_exit_rcu+0x1c/0x44
| el1_interrupt+0x4c/0xe4
| el1h_64_irq_handler+0x18/0x24
| el1h_64_irq+0x74/0x78
| smpboot_thread_fn+0x68/0x2c0
| kthread+0x124/0x130
| ret_from_fork+0x10/0x20
| irq event stamp: 193241
| hardirqs last enabled at (193240): [<ffffa0460fe10a9c>] __do_softirq+0x10c/0x5d8
| hardirqs last disabled at (193241): [<ffffa0461102ffe4>] el1_dbg+0x24/0x90
| softirqs last enabled at (193234): [<ffffa0460fe10e00>] __do_softirq+0x470/0x5d8
| softirqs last disabled at (193239): [<ffffa0460fea9944>] __irq_exit_rcu+0x180/0x1ac
| ---[ end trace 0000000000000000 ]---
The necessary manipulation of DAIF and ICC_PMR_EL1 depends on the
interrupted context, but the structure of gic_handle_irq() makes this
also depend on whether the GIC reports an IRQ, NMI, or special INTID:
* When the interrupted context had regular IRQs masked (and hence the
interrupt must be an NMI), the entry code performs the NMI
entry/exit and gic_handle_irq() should return with DAIF and
ICC_PMR_EL1 unchanged.
This is handled correctly today.
* When the interrupted context had regular IRQs unmasked, the entry code
performs IRQ entry/exit, but expects gic_handle_irq() to always update
ICC_PMR_EL1 and DAIF.IF to unmask NMIs (but not regular IRQs) prior to
returning (which it must do prior to invoking any regular IRQ
handler).
This unbalanced calling convention is necessary because we don't know
whether an NMI has been taken until acknowledged by a read from
ICC_IAR1_EL1, and so we need to perform the read with NMI masked in
case an NMI has been taken (and needs to be handled with NMIs masked).
Unfortunately, this is not handled consistently:
- When ICC_IAR1_EL1 reports a special INTID, gic_handle_irq() returns
immediately without manipulating ICC_PMR_EL1 and DAIF.
- When RPR_EL1 indicates an NMI, gic_handle_irq() calls
gic_handle_nmi() to invoke the NMI handler, then returns without
manipulating ICC_PMR_EL1 and DAIF.
- For regular IRQs, gic_handle_irq() manipulates ICC_PMR_EL1 and DAIF
prior to invoking the IRQ handler.
There were related problems with special INTID handling in the past,
where if an exception was taken from a context with regular IRQs masked
and ICC_IAR_EL1 reported a special INTID, gic_handle_irq() would
erroneously unmask NMIs in NMI context permitted an unexpected nested
NMI. That case specifically was fixed by commit:
a97709f563a078e2 ("irqchip/gic-v3: Do not enable irqs when handling spurious interrups")
... but unfortunately that commit added an inverse problem, where if an
exception was taken from a context with regular IRQs *unmasked* and
ICC_IAR_EL1 reported a special INTID, gic_handle_irq() would erroneously
fail to unmask NMIs (and consequently regular IRQs could not be
unmasked during softirq processing). Before and after that commit, if an
NMI was taken from a context with regular IRQs unmasked gic_handle_irq()
would not unmask NMIs prior to returning, leading to the same problem
with softirq handling.
This patch fixes this by restructuring gic_handle_irq(), splitting it
into separate irqson/irqsoff helper functions which consistently perform
the DAIF + ICC_PMR1_EL1 manipulation based upon the interrupted context,
regardless of the event indicated by ICC_IAR1_EL1.
The special INTID handling is moved into the low-level IRQ/NMI handler
invocation helper functions, so that early returns don't prevent the
required manipulation of DAIF + ICC_PMR_EL1.
Fixes: f32c926651dcd168 ("irqchip/gic-v3: Handle pseudo-NMIs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-4-mark.rutland@arm.com
|
|
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised. To fix this, we place an ISB between a read of
IAR and the subsequent invocation of an IRQ handler.
When EOI mode 1 is in use, we need to EOI an interrupt prior to invoking
its handler, and we have a write to EOIR for this. As this write to EOIR
requires an ISB, and this is provided by the gic_write_eoir() helper, we
omit the usual ISB in this case, with the logic being:
| if (static_branch_likely(&supports_deactivate_key))
| gic_write_eoir(irqnr);
| else
| isb();
This is somewhat opaque, and it would be a little clearer if there were
an unconditional ISB, with only the write to EOIR being conditional,
e.g.
| if (static_branch_likely(&supports_deactivate_key))
| write_gicreg(irqnr, ICC_EOIR1_EL1);
|
| isb();
This patch rewrites the code that way, with this logic factored into a
new helper function with comments explaining what the ISB is for, as
were originally laid out in commit:
39a06b67c2c1256b ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Note that since then, we removed the IAR polling in commit:
342677d70ab92142 ("irqchip/gic-v3: Remove acknowledge loop")
... which removed one of the two race conditions.
For consistency, other portions of the driver are made to manipulate
EOIR using write_gicreg() and explcit ISBs, and the gic_write_eoir()
helper function is removed.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-3-mark.rutland@arm.com
|
|
There are cases where a context synchronization event is necessary
between an IRQ being raised and being handled, and there are races such
that we cannot rely upon the exception entry being subsequent to the
interrupt being raised.
We identified and fixes this for regular IRQs in commit:
39a06b67c2c1256b ("irqchip/gic: Ensure we have an ISB between ack and ->handle_irq")
Unfortunately, we forgot to do the same for psuedo-NMIs when support for
those was added in commit:
f32c926651dcd168 ("irqchip/gic-v3: Handle pseudo-NMIs")
Which means that when pseudo-NMIs are used for PMU support, we'll hit
the same problem.
Apply the same fix as for regular IRQs. Note that when EOI mode 1 is in
use, the call to gic_write_eoir() will provide an ISB.
Fixes: f32c926651dcd168 ("irqchip/gic-v3: Handle pseudo-NMIs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220513133038.226182-2-mark.rutland@arm.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here is one fix, and three documentation updates for 5.18-rc7.
The fix is for the firmware loader which resolves a long-reported
problem where the credentials of the firmware loader could be set to a
userspace process without enough permissions to actually load the
firmware image. Many Android vendors have been reporting this for
quite some time.
The documentation updates are for the embargoed-hardware-issues.rst
file to add a new entry, change an existing one, and sort the list to
make changes easier in the future.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation/process: Update ARM contact for embargoed hardware issues
Documentation/process: Add embargoed HW contact for Ampere Computing
Documentation/process: Make groups alphabetical and use tabs consistently
firmware_loader: use kernel credentials when reading firmware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two small driver fixes for 5.18-rc7 that resolve reported
problems:
- slimbus driver irq bugfix
- interconnect sync state bugfix
Both of these have been in linux-next with no reported problems"
* tag 'char-misc-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
slimbus: qcom: Fix IRQ check in qcom_slim_probe
interconnect: Restore sync state by ignoring ipa-virt in provider count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty n_gsm and serial driver fixes for 5.18-rc7
that resolve reported problems. They include:
- n_gsm fixes for reported issues
- 8250_mtk driver fixes for some platforms
- fsl_lpuart driver fix for reported problem.
- digicolor driver fix for reported problem.
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fsl_lpuart: Don't enable interrupts too early
tty: n_gsm: fix invalid gsmtty_write_room() result
tty: n_gsm: fix mux activation issues in gsm_config()
tty: n_gsm: fix buffer over-read in gsm_dlci_data()
serial: 8250_mtk: Fix register address for XON/XOFF character
serial: 8250_mtk: Make sure to select the right FEATURE_SEL
serial: 8250_mtk: Fix UART_EFR register address
tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes for reported issues with some USB drivers.
They include:
- xhci fixes for xhci-mtk platform driver
- typec driver fixes for reported problems.
- cdc-wdm read-stuck fix
- gadget driver fix for reported race condition
- new usb-serial driver ids
All of these have been in linux-next with no reported problems"
* tag 'usb-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci-mtk: remove bandwidth budget table
usb: xhci-mtk: fix fs isoc's transfer error
usb: gadget: fix race when gadget driver register via ioctl
usb: typec: tcpci_mt6360: Update for BMC PHY setting
usb: gadget: uvc: allow for application to cleanly shutdown
usb: typec: tcpci: Don't skip cleanup in .remove() on error
usb: cdc-wdm: fix reading stuck on device close
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
|
|
Per the thread linked below, "premature next" is not considered to be a
realistic threat model, and leads to more serious security problems.
"Premature next" is the scenario in which:
- Attacker compromises the current state of a fully initialized RNG via
some kind of infoleak.
- New bits of entropy are added directly to the key used to generate the
/dev/urandom stream, without any buffering or pooling.
- Attacker then, somehow having read access to /dev/urandom, samples RNG
output and brute forces the individual new bits that were added.
- Result: the RNG never "recovers" from the initial compromise, a
so-called violation of what academics term "post-compromise security".
The usual solutions to this involve some form of delaying when entropy
gets mixed into the crng. With Fortuna, this involves multiple input
buckets. With what the Linux RNG was trying to do prior, this involves
entropy estimation.
However, by delaying when entropy gets mixed in, it also means that RNG
compromises are extremely dangerous during the window of time before
the RNG has gathered enough entropy, during which time nonces may become
predictable (or repeated), ephemeral keys may not be secret, and so
forth. Moreover, it's unclear how realistic "premature next" is from an
attack perspective, if these attacks even make sense in practice.
Put together -- and discussed in more detail in the thread below --
these constitute grounds for just doing away with the current code that
pretends to handle premature next. I say "pretends" because it wasn't
doing an especially great job at it either; should we change our mind
about this direction, we would probably implement Fortuna to "fix" the
"problem", in which case, removing the pretend solution still makes
sense.
This also reduces the crng reseed period from 5 minutes down to 1
minute. The rationale from the thread might lead us toward reducing that
even further in the future (or even eliminating it), but that remains a
topic of a future commit.
At a high level, this patch changes semantics from:
Before: Seed for the first time after 256 "bits" of estimated
entropy have been accumulated since the system booted. Thereafter,
reseed once every five minutes, but only if 256 new "bits" have been
accumulated since the last reseeding.
After: Seed for the first time after 256 "bits" of estimated entropy
have been accumulated since the system booted. Thereafter, reseed
once every minute.
Most of this patch is renaming and removing: POOL_MIN_BITS becomes
POOL_INIT_BITS, credit_entropy_bits() becomes credit_init_bits(),
crng_reseed() loses its "force" parameter since it's now always true,
the drain_entropy() function no longer has any use so it's removed,
entropy estimation is skipped if we've already init'd, the various
notifiers for "low on entropy" are now only active prior to init, and
finally, some documentation comments are cleaned up here and there.
Link: https://lore.kernel.org/lkml/YmlMGx6+uigkGiZ0@zx2c4.com/
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Nadia Heninger <nadiah@cs.ucsd.edu>
Cc: Tom Ristenpart <ristenpart@cornell.edu>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Now when Intel Elkhart Lake uses again common bit timing and there are
no other users for custom bit timing, we can bring back the changes
done by the commit 0ddd83fbebbc ("can: m_can: remove support for
custom bit timing").
This effectively reverts commit ea768b2ffec6 ("Revert "can: m_can:
remove support for custom bit timing"") while taking into account
commit ea22ba40debe ("can: m_can: make custom bittiming fields const")
and commit 7d4a101c0bd3 ("can: dev: add sanity check in
can_set_static_ctrlmode()").
Link: https://lore.kernel.org/all/20220512124144.536850-2-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This reverts commit 0e8ffdf3b86dfd44b651f91b12fcae76c25c453b.
Commit 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for
Elkhart Lake") broke the test case using bitrate switching.
| ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
| ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
| candump can0 &
| cangen can1 -I 0x800 -L 64 -e -fb \
| -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v
Above commit does everything correctly according to the datasheet.
However datasheet wasn't correct.
I got confirmation from hardware engineers that the actual CAN
hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0.
Datasheet was mirroring values from an another specification which was
based on earlier M_CAN version leading to wrong bit timings.
Therefore revert the commit and switch back to common bit timings.
Fixes: ea4c1787685d ("can: m_can: pci: use custom bit timings for Elkhart Lake")
Link: https://lore.kernel.org/all/20220512124144.536850-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Chee Hou Ong <chee.houx.ong@intel.com>
Reported-by: Aman Kumar <aman.kumar@intel.com>
Reported-by: Pallavi Kumari <kumari.pallavi@intel.com>
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Fixes: 4df95131ea80 ("net/macb: change RX path for GEM")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull more drm fixes from Dave Airlie:
"Turns out I was right, some fixes hadn't made it to me yet. The vmwgfx
ones also popped up later, but all seem like bad enough things to fix.
The dma-buf, vc4 and nouveau ones are all pretty small.
The fbdev fixes are a bit more complicated: a fix to cleanup fbdev
devices properly, uncovered some use-after-free bugs in existing
drivers. Then the fix for those bugs wasn't correct. This reverts that
fix, and puts the proper fixes in place in the drivers to avoid the
use-after-frees.
This has had a fair number of eyes on it at this stage, and I'm
confident enough that it puts things in the right place, and is less
dangerous than reverting our way out of the initial change at this
stage.
fbdev:
- revert NULL deref fix that turned into a use-after-free
- prevent use-after-free in fbdev
- efifb/simplefb/vesafb: fix cleanup paths to avoid use-after-frees
dma-buf:
- fix panic in stats setup
vc4:
- fix hdmi build
nouveau:
- tegra iommu present fix
- fix leak in backlight name
vmwgfx:
- Black screen due to fences using FIFO checks on SVGA3
- Random black screens on boot due to uninitialized drm_mode_fb_cmd2
- Hangs on SVGA3 due to command buffers being used with gbobjects"
* tag 'drm-fixes-2022-05-14' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Disable command buffers on svga3 without gbobjects
drm/vmwgfx: Initialize drm_mode_fb_cmd2
drm/vmwgfx: Fix fencing on SVGAv3
drm/vc4: hdmi: Fix build error for implicit function declaration
dma-buf: call dma_buf_stats_setup after dmabuf is in valid list
fbdev: efifb: Fix a use-after-free due early fb_info cleanup
drm/nouveau: Fix a potential theorical leak in nouveau_get_backlight_name()
drm/nouveau/tegra: Stop using iommu_present()
fbdev: vesafb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: efifb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: simplefb: Cleanup fb_info in .fb_destroy rather than .remove
fbdev: Prevent possible use-after-free in fb_release()
Revert "fbdev: Make fb_release() return -ENODEV if fbdev was unregistered"
|
|
The manual describes function 0x6 of pin PA2 as "SPI1_CLK", so change
the comment to reflect that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220504170736.2669595-1-andre.przywara@arm.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Change suniv f1c100s pinctrl,PD14 multiplexing function lvds1 to uart2
When the pin PD13 and PD14 is setting up to uart2 function in dts,
there's an error occurred:
1c20800.pinctrl: unsupported function uart2 on pin PD14
Because 'uart2' is not any one multiplexing option of PD14,
and pinctrl don't know how to configure it.
So change the pin PD14 lvds1 function to uart2.
Signed-off-by: IotaHydrae <writeforever@foxmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/tencent_70C1308DDA794C81CAEF389049055BACEC09@qq.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Multiple fixes to fbdev to address a regression at unregistration, an
iommu detection improvement for nouveau, a memory leak fix for nouveau,
pointer dereference fix for dma_buf_file_release(), and a build breakage
fix for vc4
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220513073044.ymayac7x7bzatrt7@houat
|
|
Before, the first 64 bytes of input, regardless of how entropic it was,
would be used to mutate the crng base key directly, and none of those
bytes would be credited as having entropy. Then 256 bits of credited
input would be accumulated, and only then would the rng transition from
the earlier "fast init" phase into being actually initialized.
The thinking was that by mixing and matching fast init and real init, an
attacker who compromised the fast init state, considered easy to do
given how little entropy might be in those first 64 bytes, would then be
able to bruteforce bits from the actual initialization. By keeping these
separate, bruteforcing became impossible.
However, by not crediting potentially creditable bits from those first 64
bytes of input, we delay initialization, and actually make the problem
worse, because it means the user is drawing worse random numbers for a
longer period of time.
Instead, we can take the first 128 bits as fast init, and allow them to
be credited, and then hold off on the next 128 bits until they've
accumulated. This is still a wide enough margin to prevent bruteforcing
the rng state, while still initializing much faster.
Then, rather than trying to piecemeal inject into the base crng key at
various points, instead just extract from the pool when we need it, for
the crng_init==0 phase. Performance may even be better for the various
inputs here, since there are likely more calls to mix_pool_bytes() then
there are to get_random_bytes() during this phase of system execution.
Since the preinit injection code is gone, bootloader randomness can then
do something significantly more straight forward, removing the weird
system_wq hack in hwgenerator randomness.
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
It's too hard to keep the batches synchronized, and pointless anyway,
since in !crng_ready(), we're updating the base_crng key really often,
where batching only hurts. So instead, if the crng isn't ready, just
call into get_random_bytes(). At this stage nothing is performance
critical anyhow.
Cc: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Since the RNG loses freshness with system suspend/hibernation, when we
resume, immediately reseed using whatever data we can, which for this
particular case is the various timestamps regarding system suspend time,
in addition to more generally the RDSEED/RDRAND/RDTSC values that happen
whenever the crng reseeds.
On systems that suspend and resume automatically all the time -- such as
Android -- we skip the reseeding on suspend resumption, since that could
wind up being far too busy. This is the same trade-off made in
WireGuard.
In addition to reseeding upon resumption always mix into the pool these
various stamps on every power notification event.
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Currently, we do the jitter dance if two consecutive reads to the cycle
counter return different values. If they do, then we consider the cycle
counter to be fast enough that one trip through the scheduler will yield
one "bit" of credited entropy. If those two reads return the same value,
then we assume the cycle counter is too slow to show meaningful
differences.
This methodology is flawed for a variety of reasons, one of which Eric
posted a patch to fix in [1]. The issue that patch solves is that on a
system with a slow counter, you might be [un]lucky and read the counter
_just_ before it changes, so that the second cycle counter you read
differs from the first, even though there's usually quite a large period
of time in between the two. For example:
| real time | cycle counter |
| --------- | ------------- |
| 3 | 5 |
| 4 | 5 |
| 5 | 5 |
| 6 | 5 |
| 7 | 5 | <--- a
| 8 | 6 | <--- b
| 9 | 6 | <--- c
If we read the counter at (a) and compare it to (b), we might be fooled
into thinking that it's a fast counter, when in reality it is not. The
solution in [1] is to also compare counter (b) to counter (c), on the
theory that if the counter is _actually_ slow, and (a)!=(b), then
certainly (b)==(c).
This helps solve this particular issue, in one sense, but in another
sense, it mostly functions to disallow jitter entropy on these systems,
rather than simply taking more samples in that case.
Instead, this patch takes a different approach. Right now we assume that
a difference in one set of consecutive samples means one "bit" of
credited entropy per scheduler trip. We can extend this so that a
difference in two sets of consecutive samples means one "bit" of
credited entropy per /two/ scheduler trips, and three for three, and
four for four. In other words, we can increase the amount of jitter
"work" we require for each "bit", depending on how slow the cycle
counter is.
So this patch takes whole bunch of samples, sees how many of them are
different, and divides to find the amount of work required per "bit",
and also requires that at least some minimum of them are different in
order to attempt any jitter entropy.
Note that this approach is still far from perfect. It's not a real
statistical estimate on how much these samples vary; it's not a
real-time analysis of the relevant input data. That remains a project
for another time. However, it makes the same (partly flawed) assumptions
as the code that's there now, so it's probably not worse than the status
quo, and it handles the issue Eric mentioned in [1]. But, again, it's
probably a far cry from whatever a really robust version of this would
be.
[1] https://lore.kernel.org/lkml/20220421233152.58522-1-ebiggers@kernel.org/
https://lore.kernel.org/lkml/20220421192939.250680-1-ebiggers@kernel.org/
Cc: Eric Biggers <ebiggers@google.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
All platforms are now guaranteed to provide some value for
random_get_entropy(). In case some bug leads to this not being so, we
print a warning, because that indicates that something is really very
wrong (and likely other things are impacted too). This should never be
hit, but it's a good and cheap way of finding out if something ever is
problematic.
Since we now have viable fallback code for random_get_entropy() on all
platforms, which is, in the worst case, not worse than jiffies, we can
count on getting the best possible value out of it. That means there's
no longer a use for using jiffies as entropy input. It also means we no
longer have a reason for doing the round-robin register flow in the IRQ
handler, which was always of fairly dubious value.
Instead we can greatly simplify the IRQ handler inputs and also unify
the construction between 64-bits and 32-bits. We now collect the cycle
counter and the return address, since those are the two things that
matter. Because the return address and the irq number are likely
related, to the extent we mix in the irq number, we can just xor it into
the top unchanging bytes of the return address, rather than the bottom
changing bytes of the cycle counter as before. Then, we can do a fixed 2
rounds of SipHash/HSipHash. Finally, we use the same construction of
hashing only half of the [H]SipHash state on 32-bit and 64-bit. We're
not actually discarding any entropy, since that entropy is carried
through until the next time. And more importantly, it lets us do the
same sponge-like construction everywhere.
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four fixes, all in drivers.
These patches mosly fix error legs and exceptional conditions
(scsi_dh_alua, qla2xxx). The lpfc fixes are for coding issues with
lpfc features"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Correct BDE DMA address assignment for GEN_REQ_WQE
scsi: lpfc: Fix split code for FLOGI on FCoE
scsi: qla2xxx: Fix missed DMA unmap for aborted commands
scsi: scsi_dh_alua: Properly handle the ALUA transitioning state
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Restrict ltq-cputemp to SOC_XWAY to fix build failure
- Add OF device ID table to tmp401 driver to enable auto-load
* tag 'hwmon-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ltq-cputemp) restrict it to SOC_XWAY
hwmon: (tmp401) Add OF device ID table
|
|
Pull drm fixes from Dave Airlie:
"Pretty quiet week on the fixes front, 4 amdgpu and one i915 fix.
I think there might be a few misc fbdev ones outstanding, but I'll see
if they are necessary and pass them on if so.
amdgpu:
- Disable ASPM for VI boards on ADL platforms
- S0ix DCN3.1 display fix
- Resume regression fix
- Stable pstate fix
i915:
- fix for kernel memory corruption when running a lot of OpenCL tests
in parallel"
* tag 'drm-fixes-2022-05-13' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/ctx: only reset stable pstate if the user changed it (v2)
Revert "drm/amd/pm: keep the BACO feature enabled for suspend"
drm/i915: Fix race in __i915_vma_remove_closed
drm/amd/display: undo clearing of z10 related function pointers
drm/amdgpu: vi: disable ASPM on Intel Alder Lake based systems
|
|
With very limited vram on svga3 it's difficult to handle all the surface
migrations. Without gbobjects, i.e. the ability to store surfaces in
guest mobs, there's no reason to support intermediate svga2 features,
especially because we can fall back to fb traces and svga3 will never
support those in-between features.
On svga3 we wither want to use fb traces or screen targets
(i.e. gbobjects), nothing in between. This fixes presentation on a lot
of fusion/esxi tech previews where the exposed svga3 caps haven't been
finalized yet.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Cc: <stable@vger.kernel.org> # v5.14+
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220318174332.440068-5-zack@kde.org
|
|
Transition to drm_mode_fb_cmd2 from drm_mode_fb_cmd left the structure
unitialized. drm_mode_fb_cmd2 adds a few additional members, e.g. flags
and modifiers which were never initialized. Garbage in those members
can cause random failures during the bringup of the fbcon.
Initializing the structure fixes random blank screens after bootup due
to flags/modifiers mismatches during the fbcon bring up.
Fixes: dabdcdc9822a ("drm/vmwgfx: Switch to mode_cmd2")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: <stable@vger.kernel.org> # v4.10+
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-7-zack@kde.org
|
|
Port of the vmwgfx to SVGAv3 lacked support for fencing. SVGAv3 removed
FIFO's and replaced them with command buffers and extra registers.
The initial version of SVGAv3 lacked support for most advanced features
(e.g. 3D) which made fences unnecessary. That is no longer the case,
especially as 3D support is being turned on.
Switch from FIFO commands and capabilities to command buffers and extra
registers to enable fences on SVGAv3.
Fixes: 2cd80dbd3551 ("drm/vmwgfx: Add basic support for SVGA3")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220302152426.885214-5-zack@kde.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-linus
Pull interconnect fixes from Georgi:
"interconnect fixes for v5.18-rc
This contains an additional fix for sc7180 and sdx55 platforms that helps
them to enter suspend even on devices that don't have the most recent DT
changes.
- interconnect: Restore sync state by ignoring ipa-virt in provider count
Signed-off-by: Georgi Djakov <djakov@kernel.org>"
* tag 'icc-5.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
interconnect: Restore sync state by ignoring ipa-virt in provider count
|
|
Data type of status variable, that hold the return value of the ISR,
should be irqreturn_t & not u32. This patch updates status variable type
to irqreturn_t.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220512145025.20205-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The dmabuf file uses get_next_ino()(through dma_buf_getfile() ->
alloc_anon_inode()) to get an inode number and uses the same as a
directory name under /sys/kernel/dmabuf/buffers/<ino>. This directory is
used to collect the dmabuf stats and it is created through
dma_buf_stats_setup(). At current, failure to create this directory
entry can make the dma_buf_export() to fail.
Now, as the get_next_ino() can definitely give a repetitive inode no
causing the directory entry creation to fail with -EEXIST. This is a
problem on the systems where dmabuf stats functionality is enabled on
the production builds can make the dma_buf_export(), though the dmabuf
memory is allocated successfully, to fail just because it couldn't
create stats entry.
This issue we are able to see on the snapdragon system within 13 days
where there already exists a directory with inode no "122602" so
dma_buf_stats_setup() failed with -EEXIST as it is trying to create
the same directory entry.
To make the dentry name as unique, use the dmabuf fs specific inode
which is based on the simple atomic variable increment. There is tmpfs
subsystem too which relies on its own inode generation rather than
relying on the get_next_ino() for the same reason of avoiding the
duplicate inodes[1].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/patch/?id=e809d5f0b5c912fe981dce738f3283b2010665f0
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Cc: <stable@vger.kernel.org> # 5.15.x+
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1652441296-1986-1-git-send-email-quic_charante@quicinc.com
Signed-off-by: Christian König <christian.koenig@amd.com>
|
|
In ipa_qmi_ready(), the "ipa" local variable is set when
initialized, but then set again just before it's first used.
One or the other is enough, so get rid of the first one.
References: https://lore.kernel.org/lkml/200de1bd-0f01-c334-ca18-43eed783dfac@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 530f9216a953 ("soc: qcom: ipa: AP/modem communications")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
