| Age | Commit message (Collapse) | Author |
|---|
|
Add capability to control the auto bkops during suspend.
If host explicitly enables the auto bkops (background operation) on device
then only device would perform the bkops on its own. If auto bkops is not
enabled explicitly and if the device reaches to state where it must do
background operation, device would raise the urgent bkops exception event
to host and then host will enable the auto bkops on device. This patch
adds the option to choose whether auto bkops should be enabled during
runtime suspend or not. Since we don't want to keep the device active to
perform the non critical bkops, host will enable urgent bkops only.
Keep auto-bkops enabled after resume if urgent bkops needed.
If device bkops status shows that its in critical need of executing
background operations, host should allow the device to continue doing
background operations.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The clocks for UFS device will be managed by generic DVFS (Dynamic
Voltage and Frequency Scaling) framework within kernel. This devfreq
framework works with different governors to scale the clocks. By default,
UFS devices uses simple_ondemand governor which scales the clocks up if
the load is more than upthreshold and scales down if the load is less than
downthreshold.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add freq-table-hz propery for UFS device to keep track of
<min max> frequencies supported by UFS clocks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The UFS controller clocks can be gated after certain period of
inactivity, which is typically less than runtime suspend timeout.
In addition to clocks the link will also be put into Hibern8 mode
to save more power.
The clock gating can be turned on by enabling the capability
UFSHCD_CAP_CLK_GATING. To enable entering into Hibern8 mode as part of
clock gating, set the capability UFSHCD_CAP_HIBERN8_WITH_CLK_GATING.
The tracing events for clock gating can be enabled through debugfs as:
echo 1 > /sys/kernel/debug/tracing/events/ufs/ufshcd_clk_gating/enable
cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Sometimes, the device shall report its maximum power and speed
capabilities, but we might not wish to configure it to use those
maximum capabilities.
This change adds support for the vendor specific host driver to
implement power change notify callback.
To enable configuring different power modes (number of lanes,
gear number and fast/slow modes) it is necessary to split the
configuration stage from the stage that reads the device max power mode.
In addition, it is not required to read the configuration more than
once, thus the configuration is stored after reading it once.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch adds support for UFS device and UniPro link power management
during runtime/system PM.
Main idea is to define multiple UFS low power levels based on UFS device
and UFS link power states. This would allow any specific platform or pci
driver to choose the best suited low power level during runtime and
system suspend based on their power goals.
bkops handlig:
To put the UFS device in sleep state when bkops is disabled, first query
the bkops status from the device and enable bkops on device only if
device needs time to perform the bkops.
START_STOP handling:
Before sending START_STOP_UNIT to the device well-known logical unit
(w-lun) to make sure that the device w-lun unit attention condition is
cleared.
Write protection:
UFS device specification allows LUs to be write protected, either
permanently or power on write protected. If any LU is power on write
protected and if the card is power cycled (by powering off VCCQ and/or
VCC rails), LU's write protect status would be lost. So this means those
LUs can be written now. To ensures that UFS device is power cycled only
if the power on protect is not set for any of the LUs, check if power on
write protect is set and if device is in sleep/power-off state & link in
inactive state (Hibern8 or OFF state).
If none of the Logical Units on UFS device is power on write protected
then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if
UFS device is in power-off state and UFS link is in OFF state. But current
implementation would disable all device power rails even if UFS link is
not in OFF state.
Low power mode:
If UFS link is in OFF state then UFS host controller can be power collapsed
to avoid leakage current from it. Note that if UFS host controller is power
collapsed, full UFS reinitialization will be required on resume to
re-establish the link between host and device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F.
UFS device specification use "Peripheral Device Addressing Format"
(SCSI SAM-5) for standard LUs.
UFS device may also have the Well Known LUs (also referred as W-LU) which
again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only
allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs
would start from 0xC100 onwards.
This means max. LUN number reported from UFS device could be 0xC17F hence
this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid
layer to detect the W-LUs as well.
But once the W-LUs are detected, UFSHCD driver may get the commands with
SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it
requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add
support for this mapping.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS device specification requires the UFS devices to support 4 well known
logical units:
"REPORT_LUNS" (address: 01h)
"UFS Device" (address: 50h)
"RPMB" (address: 44h)
"BOOT" (address: 30h)
UFS device's power management needs to be controlled by "POWER CONDITION"
field of SSU (START STOP UNIT) command. But this "power condition" field
will take effect only when its sent to "UFS device" well known logical unit
hence we require the scsi_device instance to represent this logical unit in
order for the UFS host driver to send the SSU command for power management.
We also require the scsi_device instance for "RPMB" (Replay Protected
Memory Block) LU so user space process can control this LU. User space may
also want to have access to BOOT LU.
This patch adds the scsi device instances for each of all well known LUs
(except "REPORT LUNS" LU).
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The maximum power consumption in active is determined by bActiveICCLevel.
The configuration is done by reading max current supported by the
regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and
reading the current consumption levels from the device for each rails
(vcc/vccq/vccq2) using power descriptor.
We configure the bActiveICCLevel attribute, with the max value that
correspond to the minimum-of(VCC-current-level,VCCQ-current-level,
VCCQ2-current-level).
In order to minimize resume latency, pre-fetch icc levels and reference
clock during initialization and avoid reading them each link startup
during resume.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In ->hce_enable_notify() callback the vendor specific initialization
may carry out additional DME configuration using UIC commands and
hence the UIC command completion interrupt enable bit should be set
before the post reset notification.
Add retries if the link-startup fails. This is required since due to
hardware timing issues, the Uni-Pro link-startup might fail. The UFS
HCI recovery procedure contradicts the Uni-Pro sequence. The UFS HCI
specifies to resend DME_LINKSTARTUP command after IS.ULLS (link-lost
interrupt) is received. The Uni-Pro specifies that if link-startup
fails the link is in "down" state. The link-lost is indicated to the
DME user only when the link is up. Hence, the UFS HCI recovery procedure
of waiting for IS.ULLS and retrying link-startup may not work properly.
At the end, if detection fails, power off (disable clocks, regulators,
phy) if the UFS device detection fails. This saves power while UFS device
is not embedded into the system.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently reading query descriptor is more tightened to each
descriptor type. This patch generalize the approach and allows
reading any parameter from any query descriptor.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add the support for voting of the regulator powering the
host controller logic.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add generic clock initialization support for UFSHCD platform
driver. The clock info is read from device tree using standard
clock bindings. A generic max-clock-frequency-hz property is
defined to save information on maximum operating clock frequency
the h/w supports.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS devices are powered by at most three external power supplies -
- VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V
- VCCQ - The controller and I/O power supply, 1.1V to 1.3V
- VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V
For some devices VCCQ or VCCQ2 are optional as they can be
generated using internal LDO inside the UFS device.
Add DT bindings for voltage regulators that can be controlled
from host driver.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some vendor specific controller versions might need to configure
vendor specific - registers, clocks, voltage regulators etc. to
initialize the host controller UTP layer and Uni-Pro stack.
Provide some common initialization operations that can be used
to configure vendor specifics. The methods can be extended in
future, for example, for power mode transitions.
The operations are vendor/board specific and hence determined with
the help of compatible property in device tree.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If LLD has added scsi device (by calling scsi_add_device) before scheduling
async scsi_scan_host then scsi_finish_async_scan() will end up calling
scsi_sysfs_add_sdev for scsi device which was already added by LLD.
This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev()
if it's already visible to rest of the kernel.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some devices may respond with wrong type for well-known logical units.
This patch forces well-known type for devices which doesn't report it
correct.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
CEA VICs 44 and 45 were missing DRM_MODE_FLAG_INTERLACE.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://people.freedesktop.org/~mlankhorst/linux into drm-next
fixups for nouveau and fencing
* 'for-airlied-next' of git://people.freedesktop.org/~mlankhorst/linux:
drm/nouveau: export reservation_object from dmabuf to ttm
drm/ttm: add reservation_object as argument to ttm_bo_init
drm: Pass dma-buf as argument to gem_prime_import_sg_table
drm/nouveau: assign fence_chan->name correctly
drm/nouveau: specify if interruptible wait is desired in nouveau_fence_sync
drm/nouveau: bump driver patchlevel to 1.2.1
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
Ok, here's the update core-stuff pull request with the locking fixup patch
fixed up with another patch.
* tag 'topic/core-stuff-2014-09-29' of git://anongit.freedesktop.org/drm-intel:
drm: Drop grab fpriv->fbs_lock in drm_fb_release
drm/udl: use container_of to resolve udl_fbdev from drm_fb_helper
drm/ast: use container_of to resolve ast_fbdev from drm_fb_helper
drm/gma500: use container_of to resolve psb_fbdev from drm_fb_helper
drm/qxl: use container_of to resolve qxl_fbdev from drm_fb_helper
drm/nouveau: use container_of to resolve nouveau_plane from drm_plane
drm/nouveau: use container_of to resolve nouveau_fbdev from drm_fb_helper
drm/radeon: use container_of to resolve radeon_fbdev from drm_fb_helper
drm/mgag200: use container_of to resolve mga_fbdev from drm_fb_helper
drm/cirrus: use container_of to resolve cirrus_fbdev from drm_fb_helper
drm: Improve debug output for drm_wait_one_vblank
drm: Fixup locking for universal cursor planes
drm: Don't update vblank timestamp when the counter didn't change
|
|
Adds an extra argument to nouveau_bo_new, which is only used in nouveau_prime.c.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
|
|
Immutable branch with restart handler patches for v3.18
|
|
The relation of i2s nodes as follows:
i2s_src 0 0 594000000 0
i2s_frac 0 0 11289600 0
i2s_pre 0 0 11289600 0
sclk_i2s0 0 0 11289600 0
i2s0_clkout 0 0 11289600 0
hclk_i2s0 1 1 99000000 0
sclk_i2s0 is the master clock, when to set rate of sclk_i2s0, should
allow to set its parent's rate, by add flag CLK_SET_RATE_PARENT for
"i2s_frac", "i2s_pre", "i2s0_clkout" and "sclk_i2s0".
Tested on rk3288 board using max98090, with command "aplay <music.wav>"
Change-Id: I12faad082566532b65a7de8c0a6845e1c17870e6
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Haswell and later silicon has added a new pixel replication register
to the pipe timings for each transcoder. Now in addition to the
DPLL_A_MD register for the pixel clock double, we also need to write
to the TRANS_MULT_n (0x6002c) register to double the pixel data. Writing
to the DPLL only double the pixel clock.
ver2: Macro name change from MULTIPLY to PIPE_MULTI. (Daniel)
ver3: Do not set pixel multiplier if transcoder is eDP (Ville)
ver4: Macro name change to PIPE_MULT and default else pixel_multiplier
Cc: Ville =?iso-8859-1?Q?Syrj=E4l=E4?= <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Appease checkpatch and move one hunk back into the right
place that git am misplace!?]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
ISDv4 and v5 are plain HID devices. We can directly implement a generic
HID parsing/handling and remove the need to manually add those PID in
the list of supported devices.
This patch implements the pen support only. The finger part will come in
a later patch.
To be properly notified of an .event() and a .report(), we need to force
hid-core to go through the HID parsing. By default, wacom.ko binds only
hidraw, so the hid parsing is not done by hid-core. When a true HID device
is there, we add the flag HID_CLAIMED_DRIVER to hid->claimed which will
force hid-core to parse the incoming reports.
(Note that this can be easily backported by directly setting the .claimed
flag to HID_CLAIMED_DRIVER even if hid-core does not support
HID_CONNECT_DRIVER)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This allows to have the input devices ready in while parsing the reports
descriptor.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If the input can be created earlier during probe, we can already populate
them while reading the report descriptor. This way, we can rely on the
hid subsystem directly for tablets which already provide a meaningful
report descriptor (like ISDv4-5).
This patch only splits the allocation and registration, but do not
change where we allocate the input. This will come in a later patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
When we have to deal with new elements in probe, having the exit labels
named sequencially is a pain to maintain. Put a meaningful name instead
so that we do not have to renumber them on inserts.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add a generic SYSCON register mapped reset mechanism.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
This patch fix the following issues.
- Flag for bq27742 is 2 bytes contracy to 1 byte for older hardware
- Don't read FLAG_CI as bq27742 does not have it
- Use Battery full capacity register as last measure discharge
Signed-off-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Add pci_remap_iospace() to map bus I/O resources into the CPU virtual
address space. Architectures with special needs may provide their own
version, but most should be able to use this one.
This function is useful for PCI host bridge drivers that need to map the
PCI I/O resources into virtual memory space.
[bhelgaas: phys_addr description, drop temporary "err" variable]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
CC: Arnd Bergmann <arnd@arndb.de>
|
|
Provide a function to parse the PCI DT ranges that can be used to create a
pci_host_bridge structure together with its associated bus.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
[make io_base parameter optional]
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add pci_get_new_domain_nr() to allocate a new domain number and
of_get_pci_domain_nr() to retrieve the PCI domain number of a given device
from DT. Host bridge drivers or architecture-specific code can choose to
implement their PCI domain number policy using these two functions.
Using of_get_pci_domain_nr() guarantees a stable PCI domain number on every
boot provided that all host bridge controllers are assigned a number in the
device tree using "linux,pci-domain" property. Mixing use of
pci_get_new_domain_nr() and of_get_pci_domain_nr() is not recommended as it
can lead to potentially conflicting domain numbers being assigned to root
buses behind different host bridges.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
|
|
The handling of PCI domains (or PCI segments in ACPI speak) is usually a
straightforward affair but its implementation is currently left to the
architectural code, with pci_domain_nr(b) querying the value of the domain
associated with bus b.
This patch introduces CONFIG_PCI_DOMAINS_GENERIC as an option that can be
selected if an architecture wants a simple implementation where the value
of the domain associated with a bus is stored in struct pci_bus.
The architectures that select CONFIG_PCI_DOMAINS_GENERIC will then have to
implement pci_bus_assign_domain_nr() as a way of setting the domain number
associated with a root bus. All child buses except the root bus will
inherit the domain_nr value from their parent.
Signed-off-by: Catalin Marinas <Catalin.Marinas@arm.com>
[Renamed pci_set_domain_nr() to pci_bus_assign_domain_nr()]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
|
|
The ranges property for a host bridge controller in DT describes the
mapping between the PCI bus address and the CPU physical address. The
resources framework however expects that the IO resources start at a pseudo
"port" address 0 (zero) and have a maximum size of IO_SPACE_LIMIT. The
conversion from PCI ranges to resources failed to take that into account,
returning a CPU physical address instead of a port number.
Also fix all the drivers that depend on the old behaviour by fetching the
CPU physical address based on the port number where it is being needed.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Catalin Marinas <catalin.marinas@arm.com>
|
|
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ldc_map_sg() could fail its check that the number of pages referred to
by the sg scatterlist was <= the number of cookies.
This fixes the issue by doing a similar thing to the xen-blkfront driver,
ensuring that the scatterlist will only ever contain a segment count <=
port->ring_cookies, and each segment will be page aligned, and <= page
size. This ensures that the scatterlist is always mappable.
Orabug: 19347817
OraBZ: 15945
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LDom diskserver doesn't return reliable geometry data. In addition,
the types for all fields in the vio_disk_geom are u16, which were being
truncated in the cast into the u8's of the Linux struct hd_geometry.
Modify vdc_getgeo() to compute the geometry from the disk's capacity in a
manner consistent with xen-blkfront::blkif_getgeo().
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interpret the media type from v1.1 protocol to support CDROM/DVD.
For v1.0 protocol, a disk's size continues to be calculated from the
geometry returned by the vdisk server. The geometry returned by the server
can be less than the actual number of sectors available in the backing
image/device due to the rounding in the division used to compute the
geometry in the vdisk server.
In v1.1 protocol a disk's actual size in sectors is returned during the
handshake. Use this size when v1.1 protocol is negotiated. Since this size
will always be larger than the former geometry computed size, disks created
under v1.0 will be forwards compatible to v1.1, but not vice versa.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A set of flags introduced in the block layer enable better control over
how protection information is handled. These flags are useful for both
error injection and data recovery purposes. Checking can be enabled and
disabled for controller and disk, and the guard tag format is now a
per-I/O property.
Update sd_protect_op to communicate the relevant information to the
low-level device driver via a set of flags in scsi_cmnd.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch sends ICMP and ICMPv6 messages for Path MTU Discovery when a remote
port MTU is smaller than the device MTU. This allows mixing newer VIO protocol
devices that support MTU negotiation with older devices that do not on the
same vswitch. It also allows Linux-Linux LDOMs to use 64K-1 data packets even
though Solaris vswitch is limited to <16K MTU.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch allows an admin to set the MTU on a sunvnet device to arbitrary
values between the minimum (68) and maximum (65535) IPv4 packet sizes.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes pre-allocated transmit buffers and instead directly maps
pending packets on demand. This saves O(n^2) maximum-sized transmit buffers,
for n hosts on a vswitch, as well as a copy to those buffers.
Single-stream TCP throughput linux-solaris dropped ~5% for 1500-byte MTU,
but linux-linux at 1500-bytes increased ~20%.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch upgrades the sunvnet driver to support VIO protocol version 1.6.
In particular, it adds per-port MTU negotiation, allowing MTUs other than
ETH_FRAMELEN with ports using newer VIO protocol versions.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setup_irq function is supposed to set up exactly one MSI IRQ. Multiple
IRQ setup is handled differently, to respect the choices made by the upper
layers.
Also only clear one MSI IRQ at a time; the PCI core will call into this
function multiple times if it has to tear down more than one MSI IRQ.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
|
|
Currently the HCI/SCI read/write functions are returning
the status of the ACPI call and also assigning the
returned value of the HCI/SCI function, however, only
the HCI/SCI status is being checked.
This patch changes such functions, returning the value
of the HCI/SCI function instead of the ACPI call status,
eliminating one parameter, and returning something
useful that indeed is being checked.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
The return codes are split in between HCI/SCI prefixes,
but they are shared (used) by both interfaces, mixing
hci_read/write calls with SCI_* return codes, and
sci_read/write calls with HCI_* ones.
This patch changes the prefix of the return codes
definitions, dropping the HCI/SCI naming and instead
replacing it with TOS (for TOShiba).
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
The function name hci_raw was used before to reflect
a raw (read/write) call to Toshiba's Hardware
Configuration Interface (HCI), however, since the
introduction of the System Configuration Interface
(SCI), that "name" no longer applies.
This patch changes the name of that function to
tci_raw (for Toshiba Configuration Interface), and
change the comments about it.
Also, the HCI_WORDS definition was changed to TCI_RAW,
to better reflect that we're no longer using pure HCI
calls, but a combination of HCI and SCI, which form
part of the Toshiba Configuration Interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Add a dependency to COMPILE_TEST so that the driver can be compiled for
test purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
