| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Two bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mpc: Poll for MCF
misc: eeprom: at24: Always append device id even if label property is set.
|
|
We use the timecounter APIs for the 48-bit PHC and packet timestamps.
We must periodically update the timecounter at roughly half the
overflow interval. The overflow interval is about 78 hours, so
update it every 19 hours (1/4 interval) for some extra margins.
Fixes: 390862f45c85 ("bnxt_en: Get the full 48-bit hardware timestamp periodically")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The datasheets have the following note for the conversion time
specification: "This parameter is specified by design and/or
characterization and it is not tested in production."
Parts have been seen that require more time to do 14-bit conversions for
the relative humidity channel. The result is ENXIO due to the address
phase of a transfer not getting an ACK.
Delay an additional 1 ms per conversion to allow for additional margin.
Fixes: 4839367d99e3 ("iio: humidity: add HDC100x support")
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Link: https://lore.kernel.org/r/20210614141820.2034827-1-chris.lesiak@licor.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In case an error occurred in the IRQ handler, the chip status is
dumped via devcoredump and all IRQs are disabled, but the chip stays
powered for further analysis.
The chip is in an undefined state and will not receive any CAN frames,
so shut down the timestamping worker, which reads the TBC register
regularly, too. This avoids any CRC read error messages if there is a
communication problem with the chip.
Fixes: efd8d98dfb90 ("can: mcp251xfd: add HW timestamp infrastructure")
Link: https://lore.kernel.org/r/20210724155131.471303-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes an incorrect way of reading error counters in messages
received for this purpose from the PCAN-USB interface. These messages
inform about the increase or decrease of the error counters, whose values
are placed in bytes 1 and 2 of the message data (not 0 and 1).
Fixes: ea8b33bde76c ("can: pcan_usb: add support of rxerr/txerr counters")
Link: https://lore.kernel.org/r/20210625130931.27438-4-s.grosjean@peak-system.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
With CONFIG_SPI=y and CONFIG_I2C=m, building fxls8962af into vmlinux
causes a link error against the I2C module:
aarch64-linux-ld: drivers/iio/accel/fxls8962af-core.o: in function `fxls8962af_fifo_flush':
fxls8962af-core.c:(.text+0x3a0): undefined reference to `i2c_verify_client'
Work around it by adding a Kconfig dependency that forces the SPI driver
to be a loadable module whenever I2C is a module.
Fixes: af959b7b96b8 ("iio: accel: fxls8962af: fix errata bug E3 - I2C burst reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210721151330.2176653-1-arnd@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Be sure to count the csum_none cases when csum offload is
enabled.
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to count the correct Tx and/or Rx packets for dynamic
interrupt moderation, depending on which we're processing on
the queue interrupt.
Fixes: 04a834592bf5 ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the interrupt coalesce value update out of the napi
thread and into the dim_work thread and set it only when it
has actually changed.
Fixes: 04a834592bf5 ("ionic: dynamic interrupt moderation")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If PTP configuration is attempted on ports that don't support
it, such as VF ports, the driver will return an error status
-95, or EOPNOSUPP and print an error message
enp98s0: hwstamp set failed: -95
Because some daemons can retry every few seconds, this can end
up filling the dmesg log and pushing out other more useful
messages.
We can catch this issue earlier in our handling and return
the error without a log message.
Fixes: 829600ce5e4e ("ionic: add ts_config replay")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the bulk of the code from ionic_set_rx_mode(), which
can be called from atomic context, into ionic_lif_rx_mode()
which is a safe context.
A call from the stack will get pushed off into a work thread,
but it is also possible to simultaneously have a call driven
by a queue reconfig request from an ethtool command or fw
recovery event. We add a mutex around the rx_mode work to be
sure they don't collide.
Fixes: 81dbc24147f9 ("ionic: change set_rx_mode from_ndo to can_sleep")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2021-07-23
This series contains updates to i40e driver only.
Arkadiusz corrects the order of calls for disabling queues to resolve
a false error message and adds a better message to the user when
transitioning FW LLDP back on while the firmware is still processing
the off request.
Lukasz adds additional information regarding possible incorrect cable
use when a PHY type error occurs.
Jedrzej adds ndo_select_queue support to resolve incorrect queue
selection when SW DCB is used and adds a warning when there are not
enough queues for desired TC configuration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ceph fixes from Ilya Dryomov:
"A subtle deadlock on lock_rwsem (marked for stable) and rbd fixes for
a -rc1 regression.
Also included a rare WARN condition tweak"
* tag 'ceph-for-5.14-rc3' of git://github.com/ceph/ceph-client:
rbd: resurrect setting of disk->private_data in rbd_init_disk()
ceph: don't WARN if we're still opening a session to an MDS
rbd: don't hold lock_rwsem while running_list is being drained
rbd: always kick acquire on "acquired" and "released" notifications
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a recently broken Kconfig dependency and ACPI device
reference counting in an iterator macro.
Specifics:
- Fix recently broken Kconfig dependency for the ACPI table override
via built-in initrd (Robert Richter)
- Fix ACPI device reference counting in the for_each_acpi_dev_match()
helper macro to avoid use-after-free (Andy Shevchenko)"
* tag 'acpi-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: utils: Fix reference counting in for_each_acpi_dev_match()
ACPI: Kconfig: Fix table override from built-in initrd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core fixes to resolve some reported problems
for 5.14-rc3. They include:
- aux bus memory leak fix
- unneeded warning message removed when removing a device link.
Both have been in linux-next with no reported problems"
* tag 'driver-core-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Prevent warning when removing a device link from unregistered consumer
driver core: auxiliary bus: Fix memory leak when driver_register() fail
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are some small char/misc driver fixes for 5.14-rc3.
Included in here are:
- MAINTAINERS file updates for two changes in different driver
subsystems
- mhi bus bugfixes
- nds32 bugfix that resolves a reported problem
All have been in linux-next with no reported problems"
* tag 'char-misc-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
nds32: fix up stack guard gap
MAINTAINERS: Change ACRN HSM driver maintainer
MAINTAINERS: Update for VMCI driver
bus: mhi: pci_generic: Fix inbound IPCR channel
bus: mhi: core: Validate channel ID when processing command completions
bus: mhi: pci_generic: Apply no-op for wake using sideband wake boolean
|
|
Similar to [1], this patch fixes the same bug in raid10. Also cleanup the
comments.
[1] commit 2417b9869b81 ("md/raid1: properly indicate failure when ending
a failed write request")
Cc: stable@vger.kernel.org
Fixes: 7cee6d4e6035 ("md/raid10: end bio when the device faulty")
Signed-off-by: Wei Shuyu <wsy@dogben.com>
Acked-by: Guoqing Jiang <jiangguoqing@kylinos.cn>
Signed-off-by: Song Liu <song@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 5.14-rc3 to resolve a bunch of tiny
problems reported. Included in here are:
- dtsi revert to resolve a problem which broke android systems that
relied on the dts name to find the USB controller device.
People are still working out the "real" solution for this, but for
now the revert is needed.
- core USB fix for pipe calculation found by syzbot
- typec fixes
- gadget driver fixes
- new usb-serial device ids
- new USB quirks
- xhci fixes
- usb hub fixes for power management issues reported
- other tiny fixes
All have been in linux-next with no reported problems"
* tag 'usb-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (27 commits)
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
Revert "USB: quirks: ignore remote wake-up on Fibocom L850-GL LTE modem"
usb: cdc-wdm: fix build error when CONFIG_WWAN_CORE is not set
Revert "arm64: dts: qcom: Harmonize DWC USB3 DT nodes name"
usb: dwc2: gadget: Fix sending zero length packet in DDMA mode.
usb: dwc2: Skip clock gating on Samsung SoCs
usb: renesas_usbhs: Fix superfluous irqs happen after usb_pkt_pop()
usb: dwc2: gadget: Fix GOUTNAK flow for Slave mode.
usb: phy: Fix page fault from usb_phy_uevent
usb: xhci: avoid renesas_usb_fw.mem when it's unusable
usb: gadget: u_serial: remove WARN_ON on null port
usb: dwc3: avoid NULL access of usb_gadget_driver
usb: max-3421: Prevent corruption of freed memory
usb: gadget: Fix Unbalanced pm_runtime_enable in tegra_xudc_probe
MAINTAINERS: repair reference in USB IP DRIVER FOR HISILICON KIRIN 970
usb: typec: stusb160x: Don't block probing of consumer of "connector" nodes
usb: typec: stusb160x: register role switch before interrupt registration
USB: usb-storage: Add LaCie Rugged USB3-FW to IGNORE_UAS
usb: ehci: Prevent missed ehci interrupts with edge-triggered MSI
usb: hub: Disable USB 3 device initiated lpm if exit latency is too high
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Couple of fixes:
* fix aggregation on mesh
* fix late enabling of 4-addr mode
* leave monitor SKBs with some headroom
* limit band information for old applications
* fix virt-wifi WARN_ON
* fix memory leak in cfg80211 BSS list maintenance
|
|
Commit 7930742d6, reverting 26fd962, missed out on reverting an incorrect
change to a return value. The niu_pci_vpd_scan_props(..) == 1 case appears
to be a normal path - treating it as an error and return -EINVAL was
breaking VPD_SCAN and causing the driver to fail to load.
Fix, so my Neptune card works again.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Shannon Nelson <shannon.lee.nelson@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Fixes: 7930742d ('Revert "niu: fix missing checks of niu_pci_eeprom_read"')
Signed-off-by: Paul Jakma <paul@jakma.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get the number of VFs of a PF correctly by calling
rvu_get_pf_numvfs in rvu_switch_disable function.
Also hwvf is not required hence remove it.
Fixes: 23109f8dd06d ("octeontx2-af: Introduce internal packet switching")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 6cc8e7430801fa23 ("loop: scale loop device by introducing per
device lock") re-opened a race window for NULL pointer dereference at
loop_validate_file() where commit 310ca162d779efee ("block/loop: Use
global lock for ioctl() operation.") has closed.
Although we need to guarantee that other loop devices will not change
during traversal, we can't take remote "struct loop_device"->lo_mutex
inside loop_validate_file() in order to avoid AB-BA deadlock. Therefore,
introduce a global lock dedicated for loop_validate_file() which is
conditionally taken before local "struct loop_device"->lo_mutex is taken.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 6cc8e7430801fa23 ("loop: scale loop device by introducing per device lock")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A wwan link created via the wwan_create_default_link procedure is
never notified to the user (RTM_NEWLINK), causing issues with user
tools relying on such event to track network links (NetworkManager).
This is because the procedure misses a call to rtnl_configure_link(),
which sets the link as initialized and notifies the new link (cf
proper usage in __rtnl_newlink()).
Cc: stable@vger.kernel.org
Fixes: ca374290aaad ("wwan: core: support default netdev creation")
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The blamed commit modified the driver to accept the addition of VID 0
without doing anything, but deleting that VID still fails:
[ 32.080780] mv88e6085 d0032004.mdio-mii:10 lan8: failed to kill vid 0081/0
Modify mv88e6xxx_port_vlan_leave() to do the same thing as the addition.
Fixes: b8b79c414eca ("net: dsa: mv88e6xxx: Fix adding vlan 0")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some pin doesn't support PUPD register, if it fails and fallbacks with
bias_set_combo case, it will call mtk_pinconf_bias_set_pupd_r1_r0() to
modify the PUPD pin again.
Since the general bias set are either PU/PD or PULLSEL/PULLEN, try
bias_set or bias_set_rev1 for the other fallback case. If the pin
doesn't support neither PU/PD nor PULLSEL/PULLEN, it will return
-ENOTSUPP.
Fixes: 81bd1579b43e ("pinctrl: mediatek: Fix fallback call path")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20210701080955.2660294-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* acpi-utils:
ACPI: utils: Fix reference counting in for_each_acpi_dev_match()
|
|
Remove devm_kfree of memory where VLAN entry to RVU PF mapping
info is saved. This will be freed anyway at driver exit.
Having this could result in warning from devm_kfree() if
the memory is not allocated due to errors in rvu_nix_block_init()
before nix_setup_txvlan().
Fixes: 9a946def264d ("octeontx2-af: Modify nix_vtag_cfg mailbox to support TX VTAG entries")
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix missing failed message if driver does not have enough queues to
complete TC command. Without this fix no message is displayed in dmesg.
Fixes: a9ce82f744dc ("i40e: Enable 'channel' mode in mqprio for TC configs")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In SW DCB mode the packets sent receive incorrect UP tags. They are
constructed correctly and put into tx_ring, but UP is later remapped by
HW on the basis of TCTUPR register contents according to Tx queue
selected, and BW used is consistent with the new UP values. This is
caused by Tx queue selection in kernel not taking into account DCB
configuration. This patch fixes the issue by implementing the
ndo_select_queue NDO callback.
Fixes: fd0a05ce74ef ("i40e: transmit, receive, and NAPI")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of PHY type error occurs, the message was too generic.
Add additional info to PHY type error indicating that it can be
wrong cable connected.
Fixes: 124ed15bf126 ("i40e: Add dual speed module support")
Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com>
Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make warning meaningful for the user.
Previously the trace:
"Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN"
was produced when user tried to start Firmware LLDP agent,
just after it was stopped with sequence:
ethtool --set-priv-flags <dev> disable-fw-lldp on
ethtool --set-priv-flags <dev> disable-fw-lldp off
(without any delay between the commands)
At that point the firmware is still processing stop command, the behavior
is expected.
Fixes: c1041d070437 ("i40e: Missing response checks in driver when starting/stopping FW LLDP")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Correct the message flow between driver and firmware when disabling
queues.
Previously in case of PF reset (due to required reinit after reconfig),
the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up
occasionally. The error was not a real issue of hardware or firmware,
it was caused by wrong sequence of messages invoked by the driver.
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Enabling the PINCTRL_SM8350 symbol without GPIOLIB or SCM causes a build
failure:
WARNING: unmet direct dependencies detected for PINCTRL_MSM
Depends on [m]: PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && (QCOM_SCM [=m] || !QCOM_SCM [=m])
Selected by [y]:
- PINCTRL_SM8350 [=y] && PINCTRL [=y] && (ARCH_QCOM [=y] || COMPILE_TEST [=y]) && GPIOLIB [=y] && OF [=y]
aarch64-linux-ld: drivers/pinctrl/qcom/pinctrl-msm.o: in function `msm_gpio_irq_set_type':
pinctrl-msm.c:(.text.msm_gpio_irq_set_type+0x1c8): undefined reference to `qcom_scm_io_readl'
The main problem here is the 'select PINCTRL_MSM', which needs to be a
'depends on' as it is for all the other front-ends. As the GPIOLIB
dependency is now implied by that, symbol, remove the duplicate
dependencies in the process.
Fixes: d5d348a3271f ("pinctrl: qcom: Add SM8350 pinctrl driver")
Fixes: 376f9e34c10f ("drivers: pinctrl: qcom: fix Kconfig dependency on GPIOLIB")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210723091400.1669716-1-arnd@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When connecting without first doing a scan, the BSS list is empty
and __cfg80211_connect_result() generates this warning:
$ iw dev wlan0 connect -w VirtWifi
[ 15.371989] ------------[ cut here ]------------
[ 15.372179] WARNING: CPU: 0 PID: 92 at net/wireless/sme.c:756 __cfg80211_connect_result+0x402/0x440
[ 15.372383] CPU: 0 PID: 92 Comm: kworker/u2:2 Not tainted 5.13.0-kvm #444
[ 15.372512] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-3.fc34 04/01/2014
[ 15.372597] Workqueue: cfg80211 cfg80211_event_work
[ 15.372756] RIP: 0010:__cfg80211_connect_result+0x402/0x440
[ 15.372818] Code: 48 2b 04 25 28 00 00 00 75 59 48 8b 3b 48 8b 76 10 48 8d 65 e0 5b 41 5c 41 5d 41 5e 5d 49 8d 65 f0 41 5d e9 d0 d4 fd ff 0f 0b <0f> 0b e9 f6 fd ff ff e8 f2 4a b4 ff e9 ec fd ff ff 0f 0b e9 19 fd
[ 15.372966] RSP: 0018:ffffc900005cbdc0 EFLAGS: 00010246
[ 15.373022] RAX: 0000000000000000 RBX: ffff8880028e2400 RCX: ffff8880028e2472
[ 15.373088] RDX: 0000000000000002 RSI: 00000000fffffe01 RDI: ffffffff815335ba
[ 15.373149] RBP: ffffc900005cbe00 R08: 0000000000000008 R09: ffff888002bdf8b8
[ 15.373209] R10: ffff88803ec208f0 R11: ffffffffffffe9ae R12: ffff88801d687d98
[ 15.373280] R13: ffff88801b5fe000 R14: ffffc900005cbdc0 R15: dead000000000100
[ 15.373330] FS: 0000000000000000(0000) GS:ffff88803ec00000(0000) knlGS:0000000000000000
[ 15.373382] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 15.373425] CR2: 000056421c468958 CR3: 000000001b458001 CR4: 0000000000170eb0
[ 15.373478] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 15.373529] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 15.373580] Call Trace:
[ 15.373611] ? cfg80211_process_wdev_events+0x10e/0x170
[ 15.373743] cfg80211_process_wdev_events+0x10e/0x170
[ 15.373783] cfg80211_process_rdev_events+0x21/0x40
[ 15.373846] cfg80211_event_work+0x20/0x30
[ 15.373892] process_one_work+0x1e9/0x340
[ 15.373956] worker_thread+0x4b/0x3f0
[ 15.374017] ? process_one_work+0x340/0x340
[ 15.374053] kthread+0x11f/0x140
[ 15.374089] ? set_kthread_struct+0x30/0x30
[ 15.374153] ret_from_fork+0x1f/0x30
[ 15.374187] ---[ end trace 321ef0cb7e9c0be1 ]---
wlan0 (phy #0): connected to 00:00:00:00:00:00
Add the fake bss just before the connect so that cfg80211_get_bss()
finds the virtual network.
As some code was duplicated, move it in a common function.
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Link: https://lore.kernel.org/r/20210706154423.11065-1-mcroce@linux.microsoft.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable]
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Pull drm fixes from Dave Airlie:
"Regular fixes - a bunch of amdgpu fixes are the main thing mostly for
the new gpus. There is also some i915 reverts for older changes that
were having some unwanted side effects. One nouveau fix for a report
regressions, and otherwise just some misc fixes.
core:
- fix for non-drm ioctls on drm fd
panel:
- avoid double free
ttm:
- refcounting fix
- NULL checks
amdgpu:
- Yellow Carp updates
- Add some Yellow Carp DIDs
- Beige Goby updates
- CIK 10bit 4K regression fix
- GFX10 golden settings updates
- eDP panel regression fix
- Misc display fixes
- Aldebaran fix
- fix COW checks
nouveau:
- init BO GEM fields
i915:
- revert async command parsing
- revert fence error propogation
- GVT fix for shadow ppgtt
vc4:
- fix interrupt handling"
* tag 'drm-fixes-2021-07-23' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/panel: raspberrypi-touchscreen: Prevent double-free
drm/amdgpu - Corrected the video codecs array name for yellow carp
drm/amd/display: Fix ASSR regression on embedded panels
drm/amdgpu: add yellow carp pci id (v2)
drm/amdgpu: update yellow carp external rev_id handling
drm/amd/pm: Support board calibration on aldebaran
drm/amd/display: change zstate allow msg condition
drm/amd/display: Populate dtbclk entries for dcn3.02/3.03
drm/amd/display: Line Buffer changes
drm/amd/display: Remove MALL function from DCN3.1
drm/amd/display: Only set default brightness for OLED
drm/amd/display: Update bounding box for DCN3.1
drm/amd/display: Query VCO frequency from register for DCN3.1
drm/amd/display: Populate socclk entries for dcn3.02/3.03
drm/amd/display: Fix max vstartup calculation for modes with borders
drm/amd/display: implement workaround for riommu related hang
drm/amd/display: Fix comparison error in dcn21 DML
drm/i915: Correct the docs for intel_engine_cmd_parser
drm/ttm: add missing NULL checks
drm/ttm: Force re-init if ttm_global_init() fails
...
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* Return -ENOTTY for non-DRM ioctls
* amdgpu: Fix COW checks
* nouveau: init BO GME fields
* panel: Avoid double free
* ttm: Fix refcounting in ttm_global_init(); NULL checks
* vc4: Fix interrupt handling
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YPlbkmH6S4VAHP9j@linux-uq9g.fritz.box
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Couple reverts from Jason getting rid of asynchronous command parsing
and fence error propagation and a GVT fix of shadow ppgtt invalidation
with proper D3 state tracking from Colin.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YPl1sIyruD0U5Orl@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull array bounds warning fix from Gustavo Silva:
"Fix a couple of out-of-bounds warnings in the media subsystem.
This is part of the ongoing efforts to globally enable -Warray-bounds"
* tag 'array-bounds-fixes-5.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
media: ngene: Fix out-of-bounds bug in ngene_command_config_free_buf()
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.14-rc3
Here are some new device ids and a device-id comment fix.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.14-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: cp210x: add ID for CEL EM3588 USB ZigBee stick
USB: serial: cp210x: fix comments for GE CS1000
USB: serial: option: add support for u-blox LARA-R6 family
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- bug fix from Haiyang for vmbus CPU assignment
- revert of a bogus patch that went into 5.14-rc1
* tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
Revert "x86/hyperv: fix logical processor creation"
Drivers: hv: vmbus: Fix duplicate CPU assignments within a device
|
|
Pull networking fixes from David Miller:
1) Fix type of bind option flag in af_xdp, from Baruch Siach.
2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao.
3) PM refcnt imbakance in r8152, from Takashi Iwai.
4) Sign extension ug in liquidio, from Colin Ian King.
5) Mising range check in s390 bpf jit, from Colin Ian King.
6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan.
7) Fix skb page recycling race, from Ilias Apalodimas.
8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin.
9) netrom timer sk refcnt issues, from Nguyen Dinh Phi.
10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric
Dumazet.
11) act_skbmod should only operate on ethernet packets, from Peilin Ye.
12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo
Abeni.
13) Fix sparx5 dependencies, from Yajun Deng.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
dpaa2-switch: seed the buffer pool after allocating the swp
net: sched: cls_api: Fix the the wrong parameter
net: sparx5: fix unmet dependencies warning
net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum
net: dsa: ensure linearized SKBs in case of tail taggers
ravb: Remove extra TAB
ravb: Fix a typo in comment
net: dsa: sja1105: make VID 4095 a bridge VLAN too
tcp: disable TFO blackhole logic by default
sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set
net: ixp46x: fix ptp build failure
ibmvnic: Remove the proper scrq flush
selftests: net: add ESP-in-UDP PMTU test
udp: check encap socket in __udp_lib_err
sctp: update active_key for asoc when old key is being replaced
r8169: Avoid duplicate sysfs entry creation error
ixgbe: Fix packet corruption due to missing DMA sync
Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()"
ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions
fsl/fman: Add fibre support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Use kref to fix KASAN splats triggered during card removal
- Don't allocate IDA for OF aliases
* tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Don't allocate IDA for OF aliases
mmc: core: Use kref in place of struct mmc_blk_data::usage
|
|
Commit 3ce6c9e2617e ("spi: add of_device_uevent_modalias support") is
incomplete, as it didn't update the modalias_show function to generate the
of: modalias string if available.
Fixes: 3ce6c9e2617e ("spi: add of_device_uevent_modalias support")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmwnpi4fya.fsf@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: 454fa271bc4e("spi: Add Meson SPICC driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The cursor plane should use the current plane state in atomic_async_update
because it would not be the new plane state in the global atomic state
since _swap_state happened when those hook are run.
Fix cursor plane issue by below modification:
1. Remove plane_helper_funcs->atomic_update(plane, state) in
mtk_drm_crtc_async_update.
2. Add mtk_drm_update_new_state in to mtk_plane_atomic_async_update to
update the cursor plane by current plane state hook and update
others plane by the new_state.
Fixes: 37418bf14c13 ("drm: Use state helper instead of the plane state pointer")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
atomic_get_output_bus_fmts() is only called when the bridge is the last
element in the bridge chain.
If mtk-dpi is not the last bridge, the format of output_bus_cfg is
MEDIA_BUS_FMT_FIXED, and mtk_dpi_dual_edge() will fail to write correct
value to regs.
Fixes: ec8747c52434 ("drm/mediatek: dpi: Add bus format negotiation")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
Any interraction with the buffer pool (seeding a buffer, acquire one) is
made through a software portal (SWP, a DPIO object).
There are circumstances where the dpaa2-switch driver probes on a DPSW
before any DPIO devices have been probed. In this case, seeding of the
buffer pool will lead to a panic since no SWPs are initialized.
To fix this, seed the buffer pool after making sure that the software
portals have been probed and are ready to be used.
Fixes: 0b1b71370458 ("staging: dpaa2-switch: handle Rx path on control interface")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the spi device table udev can autoload the spi-mux module in
the presence of an spi-mux device.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210721095321.2165453-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We create a bunch of debugfs entries as a side-effect of
ttm_global_init() and then never clean them up. This isn't usually a
problem because we free the whole debugfs directory on module unload.
However, if the global reference count ever goes to zero and then
ttm_global_init() is called again, we'll re-create those debugfs entries
and debugfs will complain in dmesg that we're creating entries that
already exist. This patch fixes this problem by changing the lifetime
of the whole TTM debugfs directory to match that of the TTM global
state.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210721152358.2893314-6-jason@jlekstrand.net
|
