| Age | Commit message (Collapse) | Author |
|---|
|
Indicate hardware (or firmware) supports that CQM packet-loss report
will be generated based on station kickout algorithm. As of now mac80211
tracks connection loss by missing msdu counts (50) whereas ath10k
firmware tracks them by missing ppdus (+ BAR tries). While firmware is
trying to adapt its rate table, mac80211 might send out low_ack event to
hostapd. This is causing frequent connect and disconnect iteration under
noisy environment or when station is roaming around.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
ath.git patches for 4.10. Major changes:
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull RCU updates from Paul E. McKenney:
- Documentation updates, yet again just simple changes.
- Miscellaneous fixes, including a change to call_rcu()'s
rcu_head alignment check.
- Security-motivated list consistency checks, which are
disabled by default behind DEBUG_LIST.
- Torture-test updates.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Conflicts:
arch/x86/kernel/fpu/core.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: rt@linuxtronix.de
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Link: http://lkml.kernel.org/r/20161117183541.8588-12-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Install the callbacks via the state machine and let the core invoke
the callbacks on the already online CPUs.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: Duc Dang <dhdang@apm.com>
Cc: rt@linuxtronix.de
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/20161117183541.8588-8-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
We accidentally allocate sizeof(u32) instead of sizeof(struct
be_cmd_get_session_resp).
Fixes: 50a4b824be9e ("scsi: be2iscsi: Fix to make boot discovery non-blocking")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While issuing any ATA passthrough command to firmware the driver will
block the device. But it will unblock the device only if the I/O
completes through the ISR path. If a controller reset occurs before
command completion the device will remain in blocked state.
Make sure we unblock the device following a controller reset if an ATA
passthrough command was queued.
[mkp: clarified patch description]
Cc: <stable@vger.kernel.org> # v4.4+
Fixes: ac6c2a93bd07 ("mpt3sas: Fix for SATA drive in blocked state, after diag reset")
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Older controllers use SCSI target id '0' for the first internal disk. As
the controllers are now placed on the same bus as the internal disks
this leads to a clash with the SCSI target id of controller. This patch
checks the SCSI revision, and moves older controller to bus '3' to be
compatible with older releases and avoid this problem.
[mkp: fixed uninitialized variable]
Fixes: 09371d623c9 ("hpsa: Change SAS transport devices to bus 0.")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fix from Zhang Rui:
"We only have one urgent fix this time.
Commit 3105f234e0ab ("thermal/powerclamp: correct cpu support check"),
which is shipped in 4.9-rc3, fixed a problem introduced by commit
b721ca0d1927 ("thermal/powerclamp: remove cpu whitelist").
But unfortunately, it broke intel_powerclamp driver module auto-
loading at the same time. Thus we need this change to add back module
auto-loading for 4.9"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal/powerclamp: add back module device table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes.
One prevents timeouts on mpt3sas when trying to use the secure erase
protocol which causes the erase protocol to be aborted. The second is
a regression in a prior fix which causes all commands to abort during
PCI extended error recovery, which is incorrect because PCI EEH is
independent from what's happening on the FC transport"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: do not abort all commands in the adapter during EEH recovery
scsi: mpt3sas: Fix secure erase premature termination
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of driver fixes.
The sunxi fixes are for an incorrect clk tree configuration and a bad
frequency calculation. The other two are fixes for passing the wrong
pointer in drivers recently converted to clk_hw style registration"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: efm32gg: Pass correct type to hw provider registration
clk: berlin: Pass correct type to hw provider registration
clk: sunxi: Fix M factor computation for APB1
clk: sunxi-ng: sun6i-a31: Force AHB1 clock to use PLL6 as parent
|
|
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:
drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.
Fixes: a0627f776a45 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6390 uses a different bit to select between bank0 and bank1
of the statistics. So implement an ops function for this, and pass the
selector bit to the generic stats read function. Also, the histogram
selection has moved for the mv88e6390, so abstract its selection as
well.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Different families have different sets of statistics. Abstract this
using a stats_get_stats op. The mv88e6390 needs a different
implementation, which will be added later.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Different families have different sets of statistics. Abstract this
using a stats_get_sset_count and stats_get_strings op. Each stat has a
bitmap, and the ops implementer uses a bit map mask to count the
statistics which apply for the family, or return the list of strings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename functions to avoid _ prefix.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The statistics unit on the mv88e6390 needs the histogram mode to be
configured in a different register compared to other devices. Add an
ops to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Rename to mv88e6390_g1_stats_set_histogram
Move into global1.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MV88E6390 has a control register for what the histogram statistics
actually contain. This means the stat_snapshot method should not set
this information. So implement the 6390 stats_snapshot function without
these bits.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Knowing the family of device belongs to helps with picking the ops
implementation which is appropriate to the device. So add a comment to
each structure of ops.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking a stats snapshot differs between same families. Abstract this
into an ops member. At the same time, move the code into global1.[ch],
since the registers are in the global1 range.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the devices added to the tables, the probe will recognize the
switch. This however is not sufficient to make it work properly, other
changes are needed because of incompatibilities.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
_mv88e6xxx_stats_wait() did not check the return value from
mv88e6xxx_g1_read(), so the compiler complained about set but unused
err.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch needs to be taken out of reset before we can read its ID
register on the MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing HDMI with Xorg on the Juno board, I find that when Xorg
starts up or shuts down, the display is shifted significantly to the
right and wrapped in the active region. (No sync bars are visible.)
The timings are correct, it behaves as if the start address has been
shifted many pixels _into_ the framebuffer.
This occurs whenever the display mode size is changed - using xrandr
in Xorg shows that changing the resolution triggers the problem
almost every time, but changing the refresh rate does not.
Using devmem2 to disable and re-enable the HDLCD resolves the issue,
and repeated disable/enable cycles do not make the issue re-appear.
Further debugging shows that we try to update the controller
configuration while enabled.
Alwys ensure that the HDLCD is disabled prior to updating the
controller timings, and use drm_crtc_vblank_off()/drm_crtc_vblank_on()
so that DRM knows whether it can expect vblank interrupts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Free memory mapping, if bcm2835_timer_init is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Pull sparc fixes from David Miller:
1) With modern networking cards we can run out of 32-bit DMA space, so
support 64-bit DMA addressing when possible on sparc64. From Dave
Tushar.
2) Some signal frame validation checks are inverted on sparc32, fix
from Andreas Larsson.
3) Lockdep tables can get too large in some circumstances on sparc64,
add a way to adjust the size a bit. From Babu Moger.
4) Fix NUMA node probing on some sun4v systems, from Thomas Tai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: drop duplicate header scatterlist.h
lockdep: Limit static allocations if PROVE_LOCKING_SMALL is defined
config: Adding the new config parameter CONFIG_PROVE_LOCKING_SMALL for sparc
sunbmac: Fix compiler warning
sunqe: Fix compiler warnings
sparc64: Enable 64-bit DMA
sparc64: Enable sun4v dma ops to use IOMMU v2 APIs
sparc64: Bind PCIe devices to use IOMMU v2 service
sparc64: Initialize iommu_map_table and iommu_pool
sparc64: Add ATU (new IOMMU) support
sparc64: Add FORCE_MAX_ZONEORDER and default to 13
sparc64: fix compile warning section mismatch in find_node()
sparc32: Fix inverted invalid_frame_pointer checks on sigreturns
sparc64: Fix find_node warning if numa node cannot be found
|
|
The WDAT watchdog driver uses functionality provided by the watchdog timer
core but it did not select it explicitly. This results following linker
error when only WDAT_WDT is enabled in Kconfig:
drivers/built-in.o: In function `wdat_wdt_probe':
drivers/watchdog/wdat_wdt.c:444: undefined reference to `devm_watchdog_register_device'
Fix this by explicitly selecting WATCHDOG_CORE when WDAT watchdog driver is
enabled.
Fixes: 058dfc767008 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull networking fixes from David Miller:
1) Clear congestion control state when changing algorithms on an
existing socket, from Florian Westphal.
2) Fix register bit values in altr_tse_pcs portion of stmmac driver,
from Jia Jie Ho.
3) Fix PTP handling in stammc driver for GMAC4, from Giuseppe
CAVALLARO.
4) Fix udplite multicast delivery handling, it ignores the udp_table
parameter passed into the lookups, from Pablo Neira Ayuso.
5) Synchronize the space estimated by rtnl_vfinfo_size and the space
actually used by rtnl_fill_vfinfo. From Sabrina Dubroca.
6) Fix memory leak in fib_info when splitting nodes, from Alexander
Duyck.
7) If a driver does a napi_hash_del() explicitily and not via
netif_napi_del(), it must perform RCU synchronization as needed. Fix
this in virtio-net and bnxt drivers, from Eric Dumazet.
8) Likewise, it is not necessary to invoke napi_hash_del() is we are
also doing neif_napi_del() in the same code path. Remove such calls
from be2net and cxgb4 drivers, also from Eric Dumazet.
9) Don't allocate an ID in peernet2id_alloc() if the netns is dead,
from WANG Cong.
10) Fix OF node and device struct leaks in of_mdio, from Johan Hovold.
11) We cannot cache routes in ip6_tunnel when using inherited traffic
classes, from Paolo Abeni.
12) Fix several crashes and leaks in cpsw driver, from Johan Hovold.
13) Splice operations cannot use freezable blocking calls in AF_UNIX,
from WANG Cong.
14) Link dump filtering by master device and kind support added an error
in loop index updates during the dump if we actually do filter, fix
from Zhang Shengju.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
tcp: zero ca_priv area when switching cc algorithms
net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit
ethernet: stmmac: make DWMAC_STM32 depend on it's associated SoC
tipc: eliminate obsolete socket locking policy description
rtnl: fix the loop index update error in rtnl_dump_ifinfo()
l2tp: fix racy SOCK_ZAPPED flag check in l2tp_ip{,6}_bind()
net: macb: add check for dma mapping error in start_xmit()
rtnetlink: fix FDB size computation
netns: fix get_net_ns_by_fd(int pid) typo
af_unix: conditionally use freezable blocking calls in read
net: ethernet: ti: cpsw: fix fixed-link phy probe deferral
net: ethernet: ti: cpsw: add missing sanity check
net: ethernet: ti: cpsw: fix secondary-emac probe error path
net: ethernet: ti: cpsw: fix of_node and phydev leaks
net: ethernet: ti: cpsw: fix deferred probe
net: ethernet: ti: cpsw: fix mdio device reference leak
net: ethernet: ti: cpsw: fix bad register access in probe error path
net: sky2: Fix shutdown crash
cfg80211: limit scan results cache size
net sched filters: pass netlink message flags in event notification
...
|
|
Declare the structure ieee802154_ops as const as it is only passed as an
argument to the function ieee802154_alloc_hw. This argument is of type
const struct ieee802154_ops *, so ieee80254_ops structures having this
property can be declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct ieee802154_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
expression e1;
@@
ieee802154_alloc_hw(e1,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct ieee802154_ops i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct ieee802154_ops i;
The before and after size details of the affected files are:
text data bss dec hex filename
8669 1176 16 9861 2685 drivers/net/ieee802154/adf7242.o
8805 1048 16 9869 268d drivers/net/ieee802154/adf7242.o
text data bss dec hex filename
7211 2296 32 9539 2543 drivers/net/ieee802154/atusb.o
7339 2160 32 9531 253b drivers/net/ieee802154/atusb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than comparing 64-bit tunnel-id, compare tunnel vni
which is 24-bit id. This also save conversion from vni
to tunnel id on each tunnel packet receive.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Geneve already has check for device socket in route
lookup function. So no need to check it in xmit
function.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are minimal difference in building Geneve header
between ipv4 and ipv6 geneve tunnels. Following patch
refactors code to unify it.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current geneve implementation has two separate cases to handle.
1. netdev xmit
2. LWT xmit.
In case of netdev, geneve configuration is stored in various
struct geneve_dev members. For example geneve_addr, ttl, tos,
label, flags, dst_cache, etc. For LWT ip_tunnel_info is passed
to the device in ip_tunnel_info.
Following patch uses ip_tunnel_info struct to store almost all
of configuration of a geneve netdevice. This allows us to unify
most of geneve driver code around ip_tunnel_info struct.
This dramatically simplify geneve code, since it does not
need to handle two different configuration cases. Removes
duplicate code, single code path can handle either type
of geneve devices.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PLL-MIPI clock is somewhat special as it has its own LDOs which
need to be turned on for this PLL to actually work and output a clock
signal.
Add the 2 LDO enable bits to the gate bits. This fixes issues with
the TCON not sending vblank interrupts when the tcon and dot clock are
indirectly clocked from the PLL-MIPI clock.
Fixes: c6e6c96d8fa6 ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
macvlan_forward_source
The function macvlan_forward_source_one has already checked the flag
IFF_UP, so needn't check it outside in macvlan_forward_source too.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's not much point, except compile test, enabling the stmmac
platform drivers unless the STM32 SoC is enabled. It's not
useful without it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While stressing a 40Gbit mlx4 NIC with busy polling, I found false
sharing in mlx4 driver that can be easily avoided.
This patch brings an additional 7 % performance improvement in UDP_RR
workload.
1) If we received no frame during one mlx4_en_process_rx_cq()
invocation, no need to call mlx4_cq_set_ci() and/or dirty ring->cons
2) Do not refill rx buffers if we have plenty of them.
This avoids false sharing and allows some bulk/batch optimizations.
Page allocator and its locks will thank us.
Finally, mlx4_en_poll_rx_cq() should not return 0 if it determined
cpu handling NIC IRQ should be changed. We should return budget-1
instead, to not fool net_rx_action() and its netdev_budget.
v2: keep AVG_PERF_COUNTER(... polled) even if polled is 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
barrier() is a big hammer compared to READ_ONCE(),
and requires comments explaining what is protected.
READ_ONCE() is more precise and compiler should generate
better overall code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlx5e_xdp_set() is currently the only place where we drop reference on the
prog sitting in priv->xdp_prog when it's exchanged by a new one. We also
need to make sure that we eventually release that reference, for example,
in case the netdev is dismantled, otherwise we leak the program.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are multiple issues in mlx5e_xdp_set():
1) The batched bpf_prog_add() is currently not checked for errors. When
doing so, it should be done at an earlier point in time to makes sure
that we cannot fail anymore at the time we want to set the program for
each channel. The batched refs short-cut can only be performed when we
don't need to perform a reset for changing the rq type and the device
was in opened state. In case the device was not in opened state, then
the next mlx5e_open_locked() will aquire the refs from the control prog
via mlx5e_create_rq(), same when we need to perform a reset.
2) When swapping the priv->xdp_prog, then no extra reference count must be
taken since we got that from call path via dev_change_xdp_fd() already.
Otherwise, we'd never be able to release the program. Also, bpf_prog_add()
without checking the return code could fail.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mlx5e_create_rq(), when creating a new queue, we call bpf_prog_add() but
without checking the return value. bpf_prog_add() can fail since 92117d8443bc
("bpf: fix refcnt overflow"), so we really must check it. Take the reference
right when we assign it to the rq from priv->xdp_prog, and just drop the
reference on error path. Destruction in mlx5e_destroy_rq() looks good, though.
Fixes: 86994156c736 ("net/mlx5e: XDP fast RX drop bpf programs support")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't try to guess what the errors from pci_irq_alloc_vectors mean, as
that's too fragile. Instead always try allocating a single vector
when multi-MSI mode fails. This makes various intel Desktop and
Laptop CPUs use MSI again.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Michael Marley <michael@michaelmarley.com>
Tested-by: Michael Marley <michael@michaelmarley.com>
Fixes: 0b9e2988ab22 ("ahci: use pci_alloc_irq_vectors")
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Revert commit 2c85025c75df (ACPI: Execute _PTS before system reboot)
as it is reported to cause poweroff and reboot to hang on Dell
Latitude E7250.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187061
Reported-by: Gianpaolo <gianpaoloc@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 3105f234e0aba43e44e277c20f9b32ee8add43d4 replaced module
cpu id table with a cpu feature check, which is logically correct.
But we need the module device table to allow module auto loading.
Cc: stable@vger.kernel.org # 4.8
Fixes:3105f234 thermal/powerclamp: correct cpu support check
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
|
