| Age | Commit message (Collapse) | Author |
|---|
|
When creating kernel CQs use 128B CQE stride if the
cache line size is 128B, 64B otherwise. This prevents
multiple CQEs from residing in a 128B cache line,
which can cause retries when there are concurrent
read and writes in one cache line.
Tested with IPoIB on PPC64, saw ~5% throughput
improvement.
Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Validate that the requested size of RQT is supported by firmware.
Fixes: c5f9092936fe ('IB/mlx5: Add Receive Work Queue Indirection table operations')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
We need to free dev->port when we fail to enable RoCE or
initialize node data.
Fixes: 0837e86a7a34 ('IB/mlx5: Add per port counters')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
sg_alloc_table gets unsigned int as parameter while the driver
returns it as size_t. Check npages isn't greater than maximum
unsigned int.
Fixes: eeb8461e36c9 ("IB: Refactor umem to use linear SG table")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When calling rdma_resolve_ip inside rdma_addr_find_l2_eth_by_grh,
the return status of the request was ignored in the callback function
causing a successful return and an empty dmac.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
On Thu, Oct 27, 2016 at 04:36:28PM +0300, Leon Romanovsky wrote:
> From: Mark Bloch <markb@mellanox.com>
>
> If the underlying netowrk type is ipv4 or ipv6 and the device supports
> routable RoCE, prefer it so the traffic could cross subnets.
>
> Signed-off-by: Mark Bloch <markb@mellanox.com>
> Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
> Signed-off-by: Leon Romanovsky <leon@kernel.org>
> ---
Hi Doug,
Please take the following v1 of this patch where I fixed spelling error
from "netowrk" to be "network".
Thanks.
>From 09f96ba3e9b4442cfb44dca04c6726e55525c9c3 Mon Sep 17 00:00:00 2001
From: Mark Bloch <markb@mellanox.com>
Date: Sun, 11 Sep 2016 06:25:10 +0000
Subject: [PATCH rdma-rc v1 3/6] IB/core: Set routable RoCE gid type for ipv4/ipv6
networks
If the underlying network type is ipv4 or ipv6 and the device supports
routable RoCE, prefer it so the traffic could cross subnets.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When there is a CM id object that has port assigned to it, it means that
the cm-id asked for the specific port that it should go by it, but if
that port was removed (hot-unplug event) the cm-id was not updated.
In order to fix that the port keeps a list of all the cm-id's that are
planning to go by it, whenever the port is removed it marks all of them
as invalid.
This commit fixes a kernel panic which happens when running traffic between
guests and we force reboot a guest mid traffic, it triggers a kernel panic:
Call Trace:
[<ffffffff815271fa>] ? panic+0xa7/0x16f
[<ffffffff8152b534>] ? oops_end+0xe4/0x100
[<ffffffff8104a00b>] ? no_context+0xfb/0x260
[<ffffffff81084db2>] ? del_timer_sync+0x22/0x30
[<ffffffff8104a295>] ? __bad_area_nosemaphore+0x125/0x1e0
[<ffffffff81084240>] ? process_timeout+0x0/0x10
[<ffffffff8104a363>] ? bad_area_nosemaphore+0x13/0x20
[<ffffffff8104aabf>] ? __do_page_fault+0x31f/0x480
[<ffffffff81065df0>] ? default_wake_function+0x0/0x20
[<ffffffffa0752675>] ? free_msg+0x55/0x70 [mlx5_core]
[<ffffffffa0753434>] ? cmd_exec+0x124/0x840 [mlx5_core]
[<ffffffff8105a924>] ? find_busiest_group+0x244/0x9f0
[<ffffffff8152d45e>] ? do_page_fault+0x3e/0xa0
[<ffffffff8152a815>] ? page_fault+0x25/0x30
[<ffffffffa024da25>] ? cm_alloc_msg+0x35/0xc0 [ib_cm]
[<ffffffffa024e821>] ? ib_send_cm_dreq+0xb1/0x1e0 [ib_cm]
[<ffffffffa024f836>] ? cm_destroy_id+0x176/0x320 [ib_cm]
[<ffffffffa024fb00>] ? ib_destroy_cm_id+0x10/0x20 [ib_cm]
[<ffffffffa034f527>] ? ipoib_cm_free_rx_reap_list+0xa7/0x110 [ib_ipoib]
[<ffffffffa034f590>] ? ipoib_cm_rx_reap+0x0/0x20 [ib_ipoib]
[<ffffffffa034f5a5>] ? ipoib_cm_rx_reap+0x15/0x20 [ib_ipoib]
[<ffffffff81094d20>] ? worker_thread+0x170/0x2a0
[<ffffffff8109b2a0>] ? autoremove_wake_function+0x0/0x40
[<ffffffff81094bb0>] ? worker_thread+0x0/0x2a0
[<ffffffff8109aef6>] ? kthread+0x96/0xa0
[<ffffffff8100c20a>] ? child_rip+0xa/0x20
[<ffffffff8109ae60>] ? kthread+0x0/0xa0
[<ffffffff8100c200>] ? child_rip+0x0/0x20
Fixes: a977049dacde ("[PATCH] IB: Add the kernel CM implementation")
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The real QP is destroyed in case of the ref count reaches zero, but
for XRC target QPs this call was missed and caused to QP leaks.
Let's call to destroy for all flows.
Fixes: 0e0ec7e0638e ('RDMA/core: Export ib_open_qp() to share XRC...')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
into drm-fixes
Just a few bug fixes for 4.9. The big one is Mario's prime fencing fix.
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu:fix vpost_needed routine
drm/amdgpu/powerplay: drop a redundant NULL check
drm/amdgpu: Attach exclusive fence to prime exported bo's. (v5)
|
|
https://github.com/ckhu-mediatek/linux.git-tags into drm-fixes
This branch include one patch to fix a typo, two patches to disable
vblank interrupt, and three patches to support HDMI 4K resolution.
* 'mediatek-drm-fixes-2016-11-11' of https://github.com/ckhu-mediatek/linux.git-tags:
drm/mediatek: modify the factor to make the pll_rate set in the 1G-2G range
drm/mediatek: enhance the HDMI driving current
drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable
drm/mediatek: clear IRQ status before enable OVL interrupt
drm/mediatek: set vblank_disable_allowed to true
drm/mediatek: fix a typo of OD_CFG to OD_RELAYMODE
|
|
New Cadence GEM hardware support Large Segment Offload (LSO):
TCP segmentation offload (TSO) as well as UDP fragmentation
offload (UFO). Support for those features was added to the driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With RGMII, we need a 1.5 to 2ns skew between clock and data lines. The
VSC8601 can handle this internally. While the VSC8601 can set more
fine-grained delays, the standard skew settings work out of the box.
The same heuristic is used to determine when this skew should be enabled
as in vsc824x_config_init().
Tested on custom board with AM3352 SOC and VSC801 PHY.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I returned to Synopsys and so I am sending this patch to update the email
address of the pcie-designware-plat author.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling napi_hash_del() before netif_napi_del() is dangerous
if a synchronize_rcu() is not enforced before NAPI struct freeing.
Lets leave this detail to core networking stack and feel
more comfortable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netdev->real_num_rx_queues setting is only available if CONFIG_SYSFS
is enabled, so we now get a build failure when that is turned off:
netronome/nfp/nfp_net_common.c: In function 'nfp_net_ring_swap_enable':
netronome/nfp/nfp_net_common.c:2489:18: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?
As far as I can tell, the check here is only used as an optimization that
we can skip in order to fix the compilation. If sysfs is disabled,
the following netif_set_real_num_rx_queues() has no effect.
Fixes: 164d1e9e5d52 ("nfp: add support for ethtool .set_channels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent merge commit bb598c1b8c9b ("Merge
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") would cause
the FIB abort warning to fire whenever we flush the FIB tables - either
during module removal or actual abort.
Move it back to its rightful location in the FIB abort function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems many drivers do not respect napi_hash_del() contract.
When napi_hash_del() is used before netif_napi_del(), an RCU grace
period is needed before freeing NAPI object.
Fixes: 91815639d880 ("virtio-net: rx busy polling support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This option was added in 6a89a314ab107a12af08c71420c19a37a30fc2d3 to
allow use of the devm_gpio_* functions without CONFIG_GPIOLIB.
However, only a few months later in
b69ac52449c658b7ac40034dc3c5f5f4a71a723d, CONFIG_GPIOLIB was added
as a dependency, defeating the original purpose of this option.
Instead of that patch, the original commit could have just been
reverted (and in fact was partially so in
403c1d0be5ccbd750d25c59d8358843a81e52e3b). Further, since this
option has a dependency on HAS_IOMEM, even though it does not
require it, it causes build failures when !HAS_IOMEM (e.g. in a
uml build).
Fix that by completely removing the option, in essence completing
the reversion of the original commit.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The nvme_remove function tears down all allocated resources in the correct
order, so no need to free queues on error during initialization. This
fixes possible use-after-free errors when queues are still associated
with a blk-mq hctx.
Reported-by: Scott Bauer <scott.bauer@intel.com>
Tested-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimbeg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
check array index first and then visit the array.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
Two fixes, one for the old clock code, one for the new implementation.
* tag 'sunxi-clk-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: Fix M factor computation for APB1
clk: sunxi-ng: sun6i-a31: Force AHB1 clock to use PLL6 as parent
|
|
Dan Carpenter reports that we're passing a pointer to a pointer
here when we should just be passing a pointer. Pass the right
pointer so that the of_clk_hw_onecell_get() sees the appropriate
data pointer on its end.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 9337631f52a8 ("clk: efm32gg: Migrate to clk_hw based OF and registration APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Dan Carpenter reports that we're passing a pointer to a pointer
here when we should just be passing a pointer. Pass the right
pointer so that the of_clk_hw_onecell_get() sees the appropriate
data pointer on its end.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Fixes: f6475e298297 ("clk: berlin: Migrate to clk_hw based registration and OF APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
The GPIO support in the hardware allows for up to 16 GPIO pins, enumerated
from 0 to 15. The driver uses the wrong value (16) to validate the GPIO
pin range in the routines to set and clear the GPIO output pins. Update
the code to use the correct value (15).
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The debugfs support in the driver uses a common routine to write the
debugfs values. In this routine, if the input file position is non-zero
then the write routine will not return an error and an output parameter
will not have been set. Because an error isn't returned an uninitialized
value will be written into a register.
Fix the common write routine to return an error if the input file position
is non-zero, which will propagate back to the caller.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ethtool::nway_reset using phy_ethtool_nway_reset. We are
already using dev->phydev all over the place so this comes for free.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Utilize the generic phy_ethtool_nway_reset() helper function to
implement an autonegotiation restart.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.
Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not rearm interrupts if we are busy polling.
mlx4 uses separate CQ for TX and RX, so number of TX interrupts
does not change, unfortunately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the following
1. When interface is being teardown and queues are being cleaned up,
free pending SKBs that are in SQ which are either not transmitted
or freed as NAPI is disabled by that time.
2. While interface initialization, delay CFG_DONE notification till
the end to avoid corner cases where TXQs are enabled but CQ
interrupts are not which results blocking transmission and kicking
off watchdog.
3. Check for IFF_UP while re-enabling RBDR interrupts from tasklet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes multiple issues
1. Convert all driver statistics to percpu counters for accuracy.
2. To avoid multiple CQEs posted by a TSO packet appended to HW,
TSO pkt's SQE has 'post_cqe' not set but a dummy SQE is added
for getting HW transmit completion notification. This dummy
SQE has 'dont_send' set and HW drops the pkt pointed to in this
thus Tx drop counter increases. This patch fixes this by subtracting
SW tx tso counter from HW Tx drop counter for actual packet drop counter.
3. Reset all individual queue's and VNIC HW stats when interface is going down.
4. Getrid off unnecessary counters in hot path.
5. Bringout all CQE error stats i.e both Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes enabling of HW verification of L3/L4 length and
TCP/UDP checksum which is currently being cleared. Also fixed VLAN
stripping config which is being cleared when multiqset is enabled.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Programming LMAC credits taking 9K frame size by default is incorrect
as for an interface which is one of the many on the same BGX/QLM
no of credits available will be less as Tx FIFO will be divided
across all interfaces. So let's say a BGX with 40G interface and another
BGX with multiple 10G, bandwidth of 10G interfaces will be effected when
traffic is running on both 40G and 10G interfaces simultaneously.
This patch fixes this issue by programming credits based on netdev's MTU.
Also fixed configuring MTU to HW and added CQE counter for pkts which
exceed this value.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the 'bgx_id' determination on 83xx where there are
4 BGX blocks instead of 2 on other platforms.
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
- Fix PCI properties in intel-lpss-pci
- Fix Resetting issue during suspend in intel-lpss-pci
- Seperate IRQs for USBC device and CHRG in intel_soc_pmic_bxtwc
- Add timeout to fix Resetting issue in stmpe
- Ensure we 'put' reference to device when done in mfd-core
* tag 'mfd-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: core: Fix device reference leak in mfd_clone_cell
mfd: stmpe: Fix RESET regression on STMPE2401
mfd: intel_soc_pmic_bxtwc: Fix usbc interrupt
mfd: intel-lpss: Do not put device in reset state on suspend
mfd: lpss: Fix Intel Kaby Lake PCH-H properties
|
|
The device-dax implementation originally tried to be tricky and allow
private read-only mappings, but in the process allowed writable
MAP_PRIVATE + MAP_NORESERVE mappings. For simplicity and predictability
just fail all private mapping attempts since device-dax memory is
statically allocated and will never support overcommit.
Cc: <stable@vger.kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap")
Reported-by: Pawel Lebioda <pawel.lebioda@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The BRIM Brothers Zone DPMX is a bicycle powermeter. This ID is for the USB
serial interface in its charging dock for the control pods, via which some
settings for the pods can be modified.
Signed-off-by: Paul Jakma <paul@jakma.org>
Cc: Barry Redmond <barry@brimbrothers.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from mfd_clone_cell().
Fixes: a9bbba996302 ("mfd: add platform_device sharing support for mfd")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Since commit c4dd1ba355aae2bc3d1213da6c66c53e3c31e028
("mfd: stmpe: Add reset support for all STMPE variant")
we're resetting the STMPE expanders before use.
This caused a regression on the STMP2401 on the Nomadik
NHK8815:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out
nmk-i2c 101f8000.i2c0: no ack received after address transmission
It turns out that we start to poll for the reset bit to
go low again too quickly: the STMPE2401 is not yet online and
ready to be asked for the status of the RESET bit.
By introducing a 10ms delay before starting to hammer
the register for information, we get back to normal:
stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101
stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101
Cc: stable@vger.kernel.org
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Fixes: c4dd1ba355aa ("mfd: stmpe: Add reset support for all STMPE variant")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The wcove USB Type-C driver is currently being flooded with
interrupts that are not targeted to it. The reason for that
is because all CHRG first level interrupts are mapped to it.
This fixes the issue by introducing separate irq for the
usbc device, and mapping only USB Type-C PHY interrupts to
it.
Fixes: 9c6235c86332 ("mfd: intel_soc_pmic_bxtwc: Add bxt_wcove_usbc device")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 41a3da2b8e163 ("mfd: intel-lpss: Save register context on
suspend") saved the register context while going to suspend and
also put the device in reset state.
Due to the resetting of device, system cannot enter S3/S0ix
states when no_console_suspend flag is enabled. The system
and serial console both hang. The resetting of device is not
needed while going to suspend. Hence remove this code.
Cc: stable@vger.kernel.org
Fixes: 41a3da2b8e163 ("mfd: intel-lpss: Save register context on suspend")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There are a few issues on Intel Kaby Lake PCH-H properties added by
commit a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs"):
- Input clock of I2C controller on Intel Kaby Lake PCH-H is 120 MHz not
133 MHz. This was probably copy-paste error from Intel Broxton I2C
properties.
- There is no default I2C SDA hold time specified which is used when
ACPI doesn't provide it. I got information from Windows driver team
that Kaby Lake PCH-H can use the same configuration than Intel
Sunrisepoint PCH.
- Common HS-UART properties are not used.
Fix these by reusing the Sunrisepoint properties on Kaby Lake PCH-H.
Fixes: a6a576b78e09 ("mfd: lpss: Add Intel Kaby Lake PCH-H PCI IDs")
Reported-by: Xiang A Wang <xiang.a.wang@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
With the s390 special case of a yielding cpu_relax() implementation gone,
we can now remove all users of cpu_relax_lowlatency() and replace them
with cpu_relax().
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: virtualization@lists.linux-foundation.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/1477386195-32736-5-git-send-email-borntraeger@de.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Some embedded systems have no use for them. This removes about
25KB from the kernel binary size when configured out.
Corresponding syscalls are routed to a stub logging the attempt to
use those syscalls which should be enough of a clue if they were
disabled without proper consideration. They are: timer_create,
timer_gettime: timer_getoverrun, timer_settime, timer_delete,
clock_adjtime, setitimer, getitimer, alarm.
The clock_settime, clock_gettime, clock_getres and clock_nanosleep
syscalls are replaced by simple wrappers compatible with CLOCK_REALTIME,
CLOCK_MONOTONIC and CLOCK_BOOTTIME only which should cover the vast
majority of use cases with very little code.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Cc: Edward Cree <ecree@solarflare.com>
Link: http://lkml.kernel.org/r/1478841010-28605-7-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
