| Age | Commit message (Collapse) | Author |
|---|
|
When moving the imx219 driver to the subdev active state, commit
e8a5b1df000e ("media: i2c: imx219: Use subdev active state") used the
pad crop rectangle stored in the subdev state to report the crop
rectangle of the active mode. That crop rectangle was however not set in
the state when setting the format, which resulted in reporting an
incorrect crop rectangle to userspace. Fix it.
Fixes: e8a5b1df000e ("media: i2c: imx219: Use subdev active state")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The imx219_init_cfg() function has stopped operating on the try format
since commit 7e700847b1fe ("media: i2c: imx219: Switch from open to
init_cfg"), but a comment in the function wasn't updated. Fix it.
While at it, improve spelling in a second comment in the function.
Fixes: 7e700847b1fe ("media: i2c: imx219: Switch from open to init_cfg")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The commit in Fixes has removed an fwnode_handle_put() call in the error
handling path of max9286_v4l2_register().
Remove the same call from max9286_v4l2_unregister().
Fixes: 1029939b3782 ("media: v4l: async: Simplify async sub-device fwnode matching")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
CONFIG_VIDEO_DEV is required by other selected symbols. Depend on it.
Link: https://lore.kernel.org/linux-media/20230828085718.3912335-1-sakari.ailus@linux.intel.com
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 29006e196a56 ("media: pci: intel: ivsc: Add CSI submodule")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The following debug output was observed while testing CXL
cxl_core:cxl_walk_cel:721: cxl_mock_mem cxl_mem.0: Opcode 0x4300 unsupported by driver
opcode 0x4300 (Get Poison) is supported by the driver and the mock
device supports it. The logic should be checking that the opcode is
both not poison and not security.
Fix the logic to allow poison and security commands.
Fixes: ad64f5952ce3 ("cxl/memdev: Only show sanitize sysfs files when supported")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20230903-cxl-cel-fix-v1-1-e260c9467be3@intel.com
[cleanup cxl_walk_cel() to centralized "enabled" checks]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Some devices are reporting controller ready mode support, but return 0
for CRTO. These devices require a much higher time to ready than that,
so they are failing to initialize after the driver starter preferring
that value over CAP.TO.
The spec requires that CAP.TO match the appropritate CRTO value, or be
set to 0xff if CRTO is larger than that. This means that CAP.TO can be
used to validate if CRTO is reliable, and provides an appropriate
fallback for setting the timeout value if not. Use whichever is larger.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217863
Reported-by: Cláudio Sampaio <patola@gmail.com>
Reported-by: Felix Yan <felixonmars@archlinux.org>
Tested-by: Felix Yan <felixonmars@archlinux.org>
Based-on-a-patch-by: Felix Yan <felixonmars@archlinux.org>
Cc: stable@vger.kernel.org
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Commit bc840ea5f9a9 ("thermal: core: Do not handle trip points with
invalid temperature") added a check for invalid temperature to the
disabled trip point check in handle_thermal_trip(), but that check was
added at a point when the trip structure has not been initialized yet.
This may cause handle_thermal_trip() to skip a valid trip point in some
cases, so fix it by moving the check to a suitable place, after
__thermal_zone_get_trip() has been called to populate the trip
structure.
Fixes: bc840ea5f9a9 ("thermal: core: Do not handle trip points with invalid temperature")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into block-6.6
Pull MD fixes from Song:
"These commits fix a bugzilla report [1] and some recent issues in 6.5
and 6.6.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=217798"
* tag 'md-fixes-20230914' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md: Put the right device in md_seq_next
md/raid1: fix error: ISO C90 forbids mixed declarations
md: fix warning for holder mismatch from export_rdev()
md: don't dereference mddev after export_rdev()
|
|
If there are multiple arrays in system and one mddevice is marked
with MD_DELETED and md_seq_next() is called in the middle of removal
then it _get()s proper device but it may _put() deleted one. As a result,
active counter may never be zeroed for mddevice and it cannot
be removed.
Put the device which has been _get with previous md_seq_next() call.
Cc: stable@vger.kernel.org
Fixes: 12a6caf27324 ("md: only delete entries from all_mddevs when the disk is freed")
Reported-by: AceLan Kao <acelan@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217798
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@linux.intel.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230914152416.10819-1-mariusz.tkaczyk@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Quite unusually, this does not contains any fix coming from subtrees
(nf, ebpf, wifi, etc).
Current release - regressions:
- bcmasp: fix possible OOB write in bcmasp_netfilt_get_all_active()
Previous releases - regressions:
- ipv4: fix one memleak in __inet_del_ifa()
- tcp: fix bind() regressions for v4-mapped-v6 addresses.
- tls: do not free tls_rec on async operation in
bpf_exec_tx_verdict()
- dsa: fixes for SJA1105 FDB regressions
- veth: update XDP feature set when bringing up device
- igb: fix hangup when enabling SR-IOV
Previous releases - always broken:
- kcm: fix memory leak in error path of kcm_sendmsg()
- smc: fix data corruption in smcr_port_add
- microchip: fix possible memory leak for vcap_dup_rule()"
* tag 'net-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
kcm: Fix error handling for SOCK_DGRAM in kcm_sendmsg().
net: renesas: rswitch: Add spin lock protection for irq {un}mask
net: renesas: rswitch: Fix unmasking irq condition
igb: clean up in all error paths when enabling SR-IOV
ixgbe: fix timestamp configuration code
selftest: tcp: Add v4-mapped-v6 cases in bind_wildcard.c.
selftest: tcp: Move expected_errno into each test case in bind_wildcard.c.
selftest: tcp: Fix address length in bind_wildcard.c.
tcp: Fix bind() regression for v4-mapped-v6 non-wildcard address.
tcp: Fix bind() regression for v4-mapped-v6 wildcard address.
tcp: Factorise sk_family-independent comparison in inet_bind2_bucket_match(_addr_any).
ipv6: fix ip6_sock_set_addr_preferences() typo
veth: Update XDP feature set when bringing up device
net: macb: fix sleep inside spinlock
net/tls: do not free tls_rec on async operation in bpf_exec_tx_verdict()
net: ethernet: mtk_eth_soc: fix pse_port configuration for MT7988
net: ethernet: mtk_eth_soc: fix uninitialized variable
kcm: Fix memory leak in error path of kcm_sendmsg()
r8152: check budget for r8152_poll()
net: dsa: sja1105: block FDB accesses that are concurrent with a switch reset
...
|
|
There's a race condition in the multipath target when retrieve_deps
races with multipath_message calling dm_get_device and dm_put_device.
retrieve_deps walks the list of open devices without holding any lock
but multipath may add or remove devices to the list while it is
running. The end result may be memory corruption or use-after-free
memory access.
See this description of a UAF with multipath_message():
https://listman.redhat.com/archives/dm-devel/2022-October/052373.html
Fix this bug by introducing a new rw semaphore "devices_lock". We grab
devices_lock for read in retrieve_deps and we grab it for write in
dm_get_device and dm_put_device.
Reported-by: Luo Meng <luomeng12@huawei.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Tested-by: Li Lingfeng <lilingfeng3@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One doc fix for drm/connector, one fix for amdgpu for an crash when
VRAM usage is high, and one fix in gm12u320 to fix the timeout units in
the code
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maxime Ripard <mripard@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/w5nlld5ukeh6bgtljsxmkex3e7s7f4qquuqkv5lv4cv3uxzwqr@pgokpejfsyef
|
|
This reverts commit a0e6a017ab56936c0405fe914a793b241ed25ee0.
Unlocking a mutex in the context of a hrtimer callback is violating mutex
locking rules, as mutex_unlock() from interrupt context is not permitted.
Link: https://lore.kernel.org/dri-devel/ZQLAc%2FFwkv%2FGiVoK@phenom.ffwll.local/T/#t
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230914102024.1789154-1-mcanal@igalia.com
|
|
The via camera controller driver selected ov7670 driver, however now that
driver has dependencies and may no longer be selected unconditionally.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 7d3c7d2a2914 ("media: i2c: Add a camera sensor top level menu")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
The Kconfig option that enables compiling camera sensor drivers is
VIDEO_CAMERA_SENSOR rather than MEDIA_CAMERA_SUPPORT as it was previously.
Fix this.
Also select VIDEO_OV7670 for marvell platform drivers only if
MEDIA_SUBDRV_AUTOSELECT and VIDEO_CAMERA_SENSOR are enabled.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 7d3c7d2a2914 ("media: i2c: Add a camera sensor top level menu")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Select MEDIA_CONTROLLER, VIDEO_V4L2_SUBDEV_API and V4L2_ASYNC as the IVSC
driver depends on all these.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308170227.ymiFlMbT-lkp@intel.com/
Fixes: 29006e196a56 ("media: pci: intel: ivsc: Add CSI submodule")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
|
|
Add spin lock protection for irq {un}mask registers' control.
After napi_complete_done() and this protection were applied,
a lot of redundant interrupts no longer occur.
For example: when "iperf3 -c <ipaddr> -R" on R-Car S4-8 Spider
Before the patches are applied: about 800,000 times happened
After the patches were applied: about 100,000 times happened
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Fix unmasking irq condition by using napi_complete_done(). Otherwise,
redundant interrupts happen.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
During rmmod, when dev_loss_tmo callback is called, an ndlp kref count is
decremented twice. Once for SCSI transport registration and second to
remove the initial node allocation kref. If there is also an NVMe
transport registration, another reference count decrement is expected in
lpfc_nvme_unregister_port().
Race conditions between the NVMe transport remoteport_delete and
dev_loss_tmo callbacks sometimes results in premature ndlp object release
resulting in use-after-free issues.
Fix by not dropping the ndlp object in dev_loss_tmo callback with an
outstanding NVMe transport registration. Inversely, mark the final
NLP_DROPPED flag in lpfc_nvme_unregister_port when rmmod flag is set.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230908211923.37603-1-justintee8345@gmail.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When a dev_loss_tmo event occurs, an ndlp lock is taken before checking
nlp_flag for NLP_DROPPED. There is an attempt to restore the ndlp lock
when exiting the if statement, but the nlp_put kref could be the final
decrement causing a use-after-free memory access on a released ndlp object.
Instead of trying to reacquire the ndlp lock after checking nlp_flag, just
return after calling nlp_put.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Link: https://lore.kernel.org/r/20230908211852.37576-1-justintee8345@gmail.com
Reviewed-by: "Ewan D. Milne" <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since debugfs_create_file() returns ERR_PTR and never NULL, use IS_ERR() to
check the return value.
Fixes: 2fcbc569b9f5 ("scsi: lpfc: Make debugfs ktime stats generic for NVME and SCSI")
Fixes: 4c47efc140fa ("scsi: lpfc: Move SCSI and NVME Stats to hardware queue structures")
Fixes: 6a828b0f6192 ("scsi: lpfc: Support non-uniform allocation of MSIX vectors to hardware queues")
Fixes: 95bfc6d8ad86 ("scsi: lpfc: Make FW logging dynamically configurable")
Fixes: 9f77870870d8 ("scsi: lpfc: Add debugfs support for cm framework buffers")
Fixes: c490850a0947 ("scsi: lpfc: Adapt partitioned XRI lists to efficient sharing")
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230906030809.2847970-1-ruanjinjie@huawei.com
Reviewed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The target_cmd_counter struct allocated via target_alloc_cmd_counter() is
never freed, resulting in leaks across various transport types, e.g.:
unreferenced object 0xffff88801f920120 (size 96):
comm "sh", pid 102, jiffies 4294892535 (age 713.412s)
hex dump (first 32 bytes):
07 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 38 01 92 1f 80 88 ff ff ........8.......
backtrace:
[<00000000e58a6252>] kmalloc_trace+0x11/0x20
[<0000000043af4b2f>] target_alloc_cmd_counter+0x17/0x90 [target_core_mod]
[<000000007da2dfa7>] target_setup_session+0x2d/0x140 [target_core_mod]
[<0000000068feef86>] tcm_loop_tpg_nexus_store+0x19b/0x350 [tcm_loop]
[<000000006a80e021>] configfs_write_iter+0xb1/0x120
[<00000000e9f4d860>] vfs_write+0x2e4/0x3c0
[<000000008143433b>] ksys_write+0x80/0xb0
[<00000000a7df29b2>] do_syscall_64+0x42/0x90
[<0000000053f45fb8>] entry_SYSCALL_64_after_hwframe+0x6e/0xd8
Free the structure alongside the corresponding iscsit_conn / se_sess
parent.
Signed-off-by: David Disseldorp <ddiss@suse.de>
Link: https://lore.kernel.org/r/20230831183459.6938-1-ddiss@suse.de
Fixes: becd9be6069e ("scsi: target: Move sess cmd counter to new struct")
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The function pm8001_pci_resume() only calls pm8001_request_irq() without
calling pm8001_setup_irq(). This causes the IRQ allocation to fail, which
leads all drives being removed from the system.
Fix this issue by integrating the code for pm8001_setup_irq() directly
inside pm8001_request_irq() so that MSI-X setup is performed both during
normal initialization and resume operations.
Fixes: dbf9bfe61571 ("[SCSI] pm8001: add SAS/SATA HBA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20230911232745.325149-2-dlemoal@kernel.org
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
OPC_INB_SET_CONTROLLER_CONFIG command
Tags allocated for OPC_INB_SET_CONTROLLER_CONFIG command need to be freed
when we receive the response.
Signed-off-by: Michal Grzedzicki <mge@meta.com>
Link: https://lore.kernel.org/r/20230911170340.699533-2-mge@meta.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some cards have more than one SAS address. Using an incorrect address
causes communication issues with some devices like expanders.
Closes: https://lore.kernel.org/linux-kernel/A57AEA84-5CA0-403E-8053-106033C73C70@fb.com/
Signed-off-by: Michal Grzedzicki <mge@meta.com>
Link: https://lore.kernel.org/r/20230913155611.3183612-1-mge@meta.com
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull in staged fixes for 6.6.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull genpm / pmdomain rename from Ulf Hansson:
"This renames the genpd subsystem to pmdomain.
As discussed on LKML, using 'genpd' as the name of a subsystem isn't
very self-explanatory and the acronym itself that means Generic PM
Domain, is known only by a limited group of people.
The suggestion to improve the situation is to rename the subsystem to
'pmdomain', which there seems to be a good consensus around using.
Ideally it should indicate that its purpose is to manage Power Domains
or 'PM domains' as we often also use within the Linux Kernel
terminology"
* tag 'pmdomain-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: Rename the genpd subsystem to pmdomain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm fix from Jarkko Sakkinen.
* tag 'tpmdd-v6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: Fix typo in tpmrm class definition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix reference to exported symbols for parisc64 [Masahiro Yamada]
- Block-TLB (BTLB) support on 32-bit CPUs
- sparse and build-warning fixes
* tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
linux/export: fix reference to exported functions for parisc64
parisc: BTLB: Initialize BTLB tables at CPU startup
parisc: firmware: Simplify calling non-PA20 functions
parisc: BTLB: _edata symbol has to be page aligned for BTLB support
parisc: BTLB: Add BTLB insert and purge firmware function wrappers
parisc: BTLB: Clear possibly existing BTLB entries
parisc: Prepare for Block-TLB support on 32-bit kernel
parisc: shmparam.h: Document aliasing requirements of PA-RISC
parisc: irq: Make irq_stack_union static to avoid sparse warning
parisc: drivers: Fix sparse warning
parisc: iosapic.c: Fix sparse warnings
parisc: ccio-dma: Fix sparse warnings
parisc: sba-iommu: Fix sparse warnigs
parisc: sba: Fix compile warning wrt list of SBA devices
parisc: sba_iommu: Fix build warning if procfs if disabled
|
|
Change the logging of each algorithm from info level to debug level.
On the original devices supported by this code there were typically only
one or two algorithms in a firmware and one or two DSPs so this logging
only used a small number of log lines.
However, for the latest devices there could be 30-40 algorithms in a
firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log
for information that isn't particularly important to have logged.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After commit 50f303496d92 ("igb: Enable SR-IOV after reinit"), removing
the igb module could hang or crash (depending on the machine) when the
module has been loaded with the max_vfs parameter set to some value != 0.
In case of one test machine with a dual port 82580, this hang occurred:
[ 232.480687] igb 0000:41:00.1: removed PHC on enp65s0f1
[ 233.093257] igb 0000:41:00.1: IOV Disabled
[ 233.329969] pcieport 0000:40:01.0: AER: Multiple Uncorrected (Non-Fatal) err0
[ 233.340302] igb 0000:41:00.0: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.352248] igb 0000:41:00.0: device [8086:1516] error status/mask=00100000
[ 233.361088] igb 0000:41:00.0: [20] UnsupReq (First)
[ 233.368183] igb 0000:41:00.0: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.376846] igb 0000:41:00.1: PCIe Bus Error: severity=Uncorrected (Non-Fata)
[ 233.388779] igb 0000:41:00.1: device [8086:1516] error status/mask=00100000
[ 233.397629] igb 0000:41:00.1: [20] UnsupReq (First)
[ 233.404736] igb 0000:41:00.1: AER: TLP Header: 40000001 0000040f cdbfc00c c
[ 233.538214] pci 0000:41:00.1: AER: can't recover (no error_detected callback)
[ 233.538401] igb 0000:41:00.0: removed PHC on enp65s0f0
[ 233.546197] pcieport 0000:40:01.0: AER: device recovery failed
[ 234.157244] igb 0000:41:00.0: IOV Disabled
[ 371.619705] INFO: task irq/35-aerdrv:257 blocked for more than 122 seconds.
[ 371.627489] Not tainted 6.4.0-dirty #2
[ 371.632257] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this.
[ 371.641000] task:irq/35-aerdrv state:D stack:0 pid:257 ppid:2 f0
[ 371.650330] Call Trace:
[ 371.653061] <TASK>
[ 371.655407] __schedule+0x20e/0x660
[ 371.659313] schedule+0x5a/0xd0
[ 371.662824] schedule_preempt_disabled+0x11/0x20
[ 371.667983] __mutex_lock.constprop.0+0x372/0x6c0
[ 371.673237] ? __pfx_aer_root_reset+0x10/0x10
[ 371.678105] report_error_detected+0x25/0x1c0
[ 371.682974] ? __pfx_report_normal_detected+0x10/0x10
[ 371.688618] pci_walk_bus+0x72/0x90
[ 371.692519] pcie_do_recovery+0xb2/0x330
[ 371.696899] aer_process_err_devices+0x117/0x170
[ 371.702055] aer_isr+0x1c0/0x1e0
[ 371.705661] ? __set_cpus_allowed_ptr+0x54/0xa0
[ 371.710723] ? __pfx_irq_thread_fn+0x10/0x10
[ 371.715496] irq_thread_fn+0x20/0x60
[ 371.719491] irq_thread+0xe6/0x1b0
[ 371.723291] ? __pfx_irq_thread_dtor+0x10/0x10
[ 371.728255] ? __pfx_irq_thread+0x10/0x10
[ 371.732731] kthread+0xe2/0x110
[ 371.736243] ? __pfx_kthread+0x10/0x10
[ 371.740430] ret_from_fork+0x2c/0x50
[ 371.744428] </TASK>
The reproducer was a simple script:
#!/bin/sh
for i in `seq 1 5`; do
modprobe -rv igb
modprobe -v igb max_vfs=1
sleep 1
modprobe -rv igb
done
It turned out that this could only be reproduce on 82580 (quad and
dual-port), but not on 82576, i350 and i210. Further debugging showed
that igb_enable_sriov()'s call to pci_enable_sriov() is failing, because
dev->is_physfn is 0 on 82580.
Prior to commit 50f303496d92 ("igb: Enable SR-IOV after reinit"),
igb_enable_sriov() jumped into the "err_out" cleanup branch. After this
commit it only returned the error code.
So the cleanup didn't take place, and the incorrect VF setup in the
igb_adapter structure fooled the igb driver into assuming that VFs have
been set up where no VF actually existed.
Fix this problem by cleaning up again if pci_enable_sriov() fails.
Fixes: 50f303496d92 ("igb: Enable SR-IOV after reinit")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:
[root@hostname ~]# hwstamp_ctl -i eth0 -r 12 -t 1
current settings:
tx_type 0
rx_filter 0
new settings:
tx_type 1
rx_filter 12
The eth0 device is properly configured to timestamp any PTPv2 events.
[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.
The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:
[root@hostname ~]# hwstamp_ctl -i eth0
current settings:
tx_type 1
rx_filter 12
Fix the issue by applying new flags only when the HW was actually
configured.
Fixes: a9763f3cb54c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes the below warnings
drivers/i2c/busses/i2c-cadence.c:221: warning: Function parameter or
member 'rinfo' not described in 'cdns_i2c'
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308171510.bKHBcZQW-lkp@intel.com/
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It has been pointed out that naming a subsystem "genpd" isn't very
self-explanatory and the acronym itself that means Generic PM Domain, is
known only by a limited group of people.
In a way to improve the situation, let's rename the subsystem to pmdomain,
which ideally should indicate that this is about so called Power Domains or
"PM domains" as we often also use within the Linux Kernel terminology.
Suggested-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230912221127.487327-1-ulf.hansson@linaro.org
|
|
Reset the i2c controller when an i2c transfer timeout occurs.
The remaining interrupts and device should be reset to avoid
unpredictable controller behavior.
Fixes: 2e57b7cebb98 ("i2c: aspeed: Add multi-master use case support")
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Tommy Huang <tommy_huang@aspeedtech.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The "i2c_mlxcpld" platform device is only instantiated on X86 systems
(through drivers/platform/x86/mlx-platform.c), or on ARM64 systems with
ACPI (through drivers/platform/mellanox/nvsw-sn2201.c). Hence further
restrict the dependency on ARM64 to ACPI, to prevent asking the user
about this driver when configuring an ARM64 kernel without ACPI support.
While at it, document in the Kconfig help text that the driver supports
ARM64/ACPI based systems, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
I2C Address Translator (ATR) support is not a stand-alone driver, but a
library. All of its users select I2C_ATR. Hence there is no need for
the user to enable this symbol manually, except when compile-testing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/lkml/20230612072807.839689-1-u.kleine-koenig@pengutronix.de/
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Heavy-weight TLB flush is required after unmap on all GPUs for
correctness and security.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Commit d2e8071bed0be ("tpm: make all 'class' structures const")
unfortunately had a typo for the name on tpmrm.
Fixes: d2e8071bed0b ("tpm: make all 'class' structures const")
Signed-off-by: Justin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
|
|
If a device has no NUMA node information associated with it, the driver
puts the device in node first_memory_node (say node 0). Not having a
NUMA node and being associated with node 0 are completely different
things and it makes little sense to mix the two.
Signed-off-by: Pratyush Yadav <ptyadav@amazon.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
There's an early return in veth_set_features() if the device is in a down
state, which leads to the XDP feature flags not being updated when enabling
GRO while the device is down. Which in turn leads to XDP_REDIRECT not
working, because the redirect code now checks the flags.
Fix this by updating the feature flags after bringing the device up.
Before this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: no
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: no
After this patch:
NETDEV_XDP_ACT_BASIC: yes
NETDEV_XDP_ACT_REDIRECT: yes
NETDEV_XDP_ACT_NDO_XMIT: yes
NETDEV_XDP_ACT_XSK_ZEROCOPY: no
NETDEV_XDP_ACT_HW_OFFLOAD: no
NETDEV_XDP_ACT_RX_SG: yes
NETDEV_XDP_ACT_NDO_XMIT_SG: yes
Fixes: fccca038f300 ("veth: take into account device reconfiguration for xdp_features flag")
Fixes: 66c0e13ad236 ("drivers: net: turn on XDP features")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20230911135826.722295-1-toke@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commit d21fdd07cea4 ("driver core: Return proper error code when
dev_set_name() fails") rewrote the logic of handling the dev_set_name()
error codes, but missed the point that initially set error value to
-EINVAL might be rewritten and hence the error path can't be triggered
at some circumstances. To fix this, make sure that error variable is
set to -EINVAL when other conditionals are false.
Reported-by: syzbot+bdfb03b1ec8b342c12cb@syzkaller.appspotmail.com
Fixes: d21fdd07cea4 ("driver core: Return proper error code when dev_set_name() fails")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230828145824.3895288-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b5c75b68b7ded84d4c82118974ce3975a4dcaa74.
The commit makes it impossible to select configuration options that
depend on COMEDI_8254, COMEDI_DAS08, COMEDI_NI_LABPC, or
COMEDI_AMPLC_DIO200 options due to changing 'select' directives to
'depends on' directives and there being no other way to select those
codependent configuration options.
Fixes: b5c75b68b7de ("comedi: add HAS_IOPORT dependencies")
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Arnd Bergmann <arnd@kernel.org>
Cc: <stable@vger.kernel.org> # v6.5+
Acked-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20230905090922.3314-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
macb_set_tx_clk() is called under a spinlock but itself calls clk_set_rate()
which can sleep. This results in:
| BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
| pps pps1: new PPS source ptp1
| in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 40, name: kworker/u4:3
| preempt_count: 1, expected: 0
| RCU nest depth: 0, expected: 0
| 4 locks held by kworker/u4:3/40:
| #0: ffff000003409148
| macb ff0c0000.ethernet: gem-ptp-timer ptp clock registered.
| ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #1: ffff8000833cbdd8 ((work_completion)(&pl->resolve)){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
| #2: ffff000004f01578 (&pl->state_mutex){+.+.}-{4:4}, at: phylink_resolve+0x44/0x4e8
| #3: ffff000004f06f50 (&bp->lock){....}-{3:3}, at: macb_mac_link_up+0x40/0x2ac
| irq event stamp: 113998
| hardirqs last enabled at (113997): [<ffff800080e8503c>] _raw_spin_unlock_irq+0x30/0x64
| hardirqs last disabled at (113998): [<ffff800080e84478>] _raw_spin_lock_irqsave+0xac/0xc8
| softirqs last enabled at (113608): [<ffff800080010630>] __do_softirq+0x430/0x4e4
| softirqs last disabled at (113597): [<ffff80008001614c>] ____do_softirq+0x10/0x1c
| CPU: 0 PID: 40 Comm: kworker/u4:3 Not tainted 6.5.0-11717-g9355ce8b2f50-dirty #368
| Hardware name: ... ZynqMP ... (DT)
| Workqueue: events_power_efficient phylink_resolve
| Call trace:
| dump_backtrace+0x98/0xf0
| show_stack+0x18/0x24
| dump_stack_lvl+0x60/0xac
| dump_stack+0x18/0x24
| __might_resched+0x144/0x24c
| __might_sleep+0x48/0x98
| __mutex_lock+0x58/0x7b0
| mutex_lock_nested+0x24/0x30
| clk_prepare_lock+0x4c/0xa8
| clk_set_rate+0x24/0x8c
| macb_mac_link_up+0x25c/0x2ac
| phylink_resolve+0x178/0x4e8
| process_one_work+0x1ec/0x51c
| worker_thread+0x1ec/0x3e4
| kthread+0x120/0x124
| ret_from_fork+0x10/0x20
The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.
Fixes: 633e98a711ac0 ("net: macb: use resolved link config in mac_link_up()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230908112913.1701766-1-s.hauer@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Apparently Acer Chromebook C740 (BDW-ULT) doesn't have the
eDP HPD line properly connected, and thus fails the new
HPD check during eDP probe. The result is that we lose the
eDP output.
I suspect all such machines would be Chromebooks or other
Linux exclusive systems as the Windows driver likely wouldn't
work either. I did check a few other BDW machines here and
those do have eDP HPD connected, one of them even is a
different Chromebook (Samus).
To account for these funky machines let's skip the HPD check when
it looks like the eDP port is the only one using that specific AUX
channel. In case of multiple ports sharing the same AUX CH (eg. on
Asrock B250M-HDV) we still do the check and thus should correctly
ignore the eDP port in favor of the other DP port (usually a DP->VGA
converter).
v2: Don't oops during list iteration
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9264
Fixes: cfe5bdfb27fa ("drm/i915: Check HPD live state during eDP probe")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230908052527.685-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
(cherry picked from commit 70052100fabec5d8c1b09c9959817a2f4517e6b5)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Forwarding to v6.6-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
[HOW & Why]
There seems to be an issue with 2nd DPIA acquiring link encoder for tiled displays.
Solution is to remove check for eng_id before we get first dynamic encoder for it
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For DPIA we should have preferred DIG assignment based on DPIA selected
as per the ASIC design.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Fix the typo in the kernel-doc for @replay_mode to prevent
kernel-doc warnings:
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:623: warning: Incorrect use of kernel-doc format: * @replay mode: Replay supported
drivers/gpu/drm/amd/display/amdgpu_dm/amdgpu_dm.h:626: warning: Function parameter or member 'replay_mode' not described in 'amdgpu_hdmi_vsdb_info'
Fixes: ec8e59cb4e0c ("drm/amd/display: Get replay info from VSDB")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
