| Age | Commit message (Collapse) | Author |
|---|
|
The ice hardware has a synchronization mechanism used to drive the
simultaneous application of commands on both PHY ports and the source timer
in the MAC.
When issuing a sync via ice_ptp_exec_tmr_cmd(), the hardware will
simultaneously apply the commands programmed for the main timer and each
PHY port. Neither the main timer command register, nor the PHY port command
registers auto clear on command execution.
During the execution of a timer command intended for a single port on E822
devices, such as those used to configure a PHY during link up, the driver
is not correctly clearing the previous commands.
This results in unintentionally executing the last programmed command on
the main timer and other PHY ports whenever performing reconfiguration on
E822 ports after link up. This results in unintended side effects on other
timers, depending on what command was previously programmed.
To fix this, the driver must ensure that the main timer and all other PHY
ports are properly initialized to perform no action.
The enumeration for timer commands does not include an enumeration value
for doing nothing. Introduce ICE_PTP_NOP for this purpose. When writing a
timer command to hardware, leave the command bits set to zero which
indicates that no operation should be performed on that port.
Modify ice_ptp_one_port_cmd() to always initialize all ports. For all ports
other than the one being configured, write their timer command register to
ICE_PTP_NOP. This ensures that no side effect happens on the timer command.
To fix this for the PHY ports, modify ice_ptp_one_port_cmd() to always
initialize all other ports to ICE_PTP_NOP. This ensures that no side
effects happen on the other ports.
Call ice_ptp_src_cmd() with a command value if ICE_PTP_NOP in
ice_sync_phy_timer_e822() and ice_start_phy_timer_e822().
With both of these changes, the driver should no longer execute a stale
command on the main timer or another PHY port when reconfiguring one of the
PHY ports after link up.
Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support")
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the internal code inside a helper function, fix the
initialization of the parameters used in the helper function
(`hidpp->answer_available` was not reset and `*response` wasn't either),
and use a `do {...} while();` loop.
Fixes: 586e8fede795 ("HID: logitech-hidpp: Retry commands when device is busy")
Cc: stable@vger.kernel.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20230621-logitech-fixes-v2-1-3635f7f9c8af@kernel.org
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
|
|
Use is_multicast_ether_addr() to perform the Checking.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230814124212.302738-2-ruanjinjie@huawei.com
|
|
Commit d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
declared but never implemented these, remove it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230816130550.50896-1-yuehaibing@huawei.com
|
|
Currently the extraie length is directly used to allocate skb buffer. When
the length of skb is greater than the max message length which firmware
supports, error will happen in firmware side.
Hence add check for the skb length and drop extraie when overflow and
print a message.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230809081657.13858-1-quic_wgong@quicinc.com
|
|
The debugfs_create_dir() function returns error pointers,
it never returns NULL. Most incorrect error checks were fixed,
but the one in ath9k_htc_init_debug() was forgotten.
Fix the remaining error check.
Fixes: e5facc75fa91 ("ath9k_htc: Cleanup HTC debugfs")
Signed-off-by: Wang Ming <machel@vivo.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230713030358.12379-1-machel@vivo.com
|
|
Registers of mdio accessing are common defined in libwx, remove the
redundant macro definitions in ngbe driver.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wangxun SP chip supports to connect with external PHY (marvell 88x3310),
which links to 10GBASE-T/1000BASE-T/100BASE-T. Add the identification of
media types from subsystem device IDs. For sp_media_copper, register mdio
bus for the external PHY.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Disable data path before PCS VR reset while switching PCS mode, to prevent
the blocking of data path. Enable AN interrupt for CL37 auto-negotiation.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since XPCS device identifier is implemented in the firmware version
0x20010 and above, so add a warning to prompt the users to upgrade the
firmware to make sure the driver works.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Wangxun NICs support the connection with SFP to RJ45 module. In this case,
PCS need to be configured in SGMII mode.
According to chapter 6.11.1 "SGMII Auto-Negitiation" of DesignWare Cores
Ethernet PCS (version 3.20a) and custom design manual, do the following
configuration when the interface mode is SGMII.
1. program VR_MII_AN_CTRL bit(3) [TX_CONFIG] = 1b (PHY side SGMII)
2. program VR_MII_AN_CTRL bit(8) [MII_CTRL] = 1b (8-bit MII)
3. program VR_MII_DIG_CTRL1 bit(0) [PHY_MODE_CTRL] = 1b
Also CL37 AN in backplane configurations need to be enabled because of the
special hardware design. Another thing to note is that PMA needs to be
reconfigured before each CL37 AN configuration for SGMII, otherwise AN will
fail, although we don't know why.
On this device, CL37_ANSGM_STS (bit[4:1] of VR_MII_AN_INTR_STS) indicates
the status received from remote link during the auto-negotiation, and
self-clear after the auto-negotiation is complete.
Meanwhile, CL37_ANCMPLT_INTR will be set to 1, to indicate CL37 AN is
complete. So add another way to get the state for CL37 SGMII.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable CL37 AN complete interrupt for DW XPCS. It requires to clear the
bit(0) [CL37_ANCMPLT_INTR] of VR_MII_AN_INTR_STS after AN completed.
And there is a quirk for Wangxun devices to enable CL37 AN in backplane
configurations because of the special hardware design.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching interface
mode.
If the interface changes, the following setting is required:
1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good)
2. write SR_XS_PCS_CTRL2 to select various PCS type
3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed
4. program PMA registers
5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific
Soft Reset)
6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared
Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun
devices. And there is a quirk for Wangxun devices to switch mode although
the interface in phylink state has not changed, since PCS will change to
default 10GBASE-R when the ethernet driver(txgbe) do LAN reset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Wangxun 10Gb NICs require some special configuration on the IP of
Synopsys Designware XPCS, introduce dev_flag for different vendors. Read
OUI from device identifier registers, to detect Wangxun devices.
And xpcs_soft_reset() is skipped to avoid the reset of device identifier
registers.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don Brace <don.brace@microchip.com> says:
cat smartpqi_6.6_cover_letter
These patches are based on Martin Petersen's 6.6/scsi-queue tree
https://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi.git
6.6/scsi-queue
The biggest functional change to smartpqi is the addition of an abort
handler. Some customers were complaining about I/O stalls to all
devices when only one device is reset. Adding an abort handler helps
to prevent I/O stalls to all devices.
All of the reset of the patches are small changes to logging messages,
MACRO and variable name changes, and one minor change for LUN
assignments.
This set of changes consists of:
* smartpqi-add-abort-handler
When a device reset occurs, the SML pauses I/O to all devices presented
by a controller instance causing some performance issues.
To only affect device with a problematic request, we added an abort handler.
The abort handler is implemented by using a device reset, but I/O to the
other devices is no longer affected.
* smartpqi-refactor-rename-MACRO-to-clarify-purpose
The MACRO SOP_RC_INCORRECT_LOGICAL_UNIT was used to check for a condition
where a TMF was sent an incorrect LUN. We renamed this MACRO to
SOP_TMF_INCORRECT_LOGICAL_UNIT for clarity.
* smartpqi-refactor-rename-pciinfo-to-pci_info
Change the pciinfo variable to pci_info to make more readable code.
No functional changes.
* smartpqi-simplify-lun_number-assignment
We simplified the conditional expression used to populate LUN numbers
for requests.
* smartpqi-enhance-shutdown-notification
Clarify controller cache flush errors. We added in more precise information
to the cache flush informational message.
No functional changes.
* smartpqi-enhance-controller-offline-notification
The driver can offline a controller for multiple reasons. We added
a description of why these rare offline actions are taken. And a function
to provide the specific details of the shutdown.
* smartpqi-enhance-error-messages
We added host:bus:target:lun to messages emitted in our reset/abort handlers.
No functional changes.
* smartpqi-change-driver-version-to-2.1.24-046
Link: https://lore.kernel.org/r/20230824155812.789913-1-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Fix TLB invalidation (Alan)
- Fix Display HPD polling (Imre)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZOdOP31OE/Cf1ojo@intel.com
|
|
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-9-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add more detail to some TMF messages.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-8-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add a description for the reason the controller has been taken off-line.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: David Strahan <David.Strahan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-7-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Provide more detailed information about cache flush errors during shutdown.
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: David Strahan <David.Strahan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-6-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Simplify lun_number assignment. lun_number assignment is only required for
non-AIO requests.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: David Strahan <David.Strahan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-5-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Make pci device structure names consistent and readable.
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-4-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Rename SOP_RC_INCORRECT_LOGICAL_UNIT to SOP_TMF_INCORRECT_LOGICAL_UNIT to
clarify the intended purpose.
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-3-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Implement aborts as resets.
Avoid I/O stalls across all devices attached to a controller when device
I/O requests time out.
Reviewed-by: Mahesh Rajashekhara <mahesh.rajashekhara@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Link: https://lore.kernel.org/r/20230824155812.789913-2-don.brace@microchip.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit 41320b18a0e0 ("scsi: snic: Fix possible memory leak if device_add()
fails") fixed the memory leak caused by dev_set_name() when device_add()
failed. However, it did not consider that 'tgt' has already been released
when put_device(&tgt->dev) is called. Remove kfree(tgt) in the error path
to avoid double free of 'tgt' and move put_device(&tgt->dev) after the
removed kfree(tgt) to avoid a use-after-free.
Fixes: 41320b18a0e0 ("scsi: snic: Fix possible memory leak if device_add() fails")
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230819083941.164365-1-wangzhu9@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move the sd_pm_ops and sd_template data structures to just above init_sd()
such that the number of forward function declarations can be reduced.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230823210628.523244-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Many tape devices will automatically rewind following a poweron/reset.
This can result in data loss as other operations in the driver can write to
the tape when the position is unknown. E.g. MTEOM can write a filemark at
the beginning of the tape. This patch adds code to detect poweron/reset
unit attentions and prevents the driver from writing to the tape when the
position could be unknown.
Customer reported problem description:
We have experienced an issue with the SCSI tape driver (st) which has led
to data loss for us on two separate occasions in production, as well as in
a third case in which we were able to reproduce the failure in our test
environment.
The tape device involved is an Amazon Tape Gateway, a virtual tape library
(VTL) appliance which presents as a series of iSCSI targets (multiple tape
drives and a changer) and is backed by storage in Amazon S3. The problem is
a general one and not limited to any particular SCSI transport or tape
device, though the nature of both iSCSI and the VTL make data loss somewhat
more likely with this combination than with a physical tape drive.
The observed behavior occurs when an error causes the VTL tape gateway
process (on the appliance) to crash and restart. This interrupts the iSCSI
TCP connections and, when it occurs during a write, causes the write to
fail with EIO. However, we then find that the virtual tape in question is
now completely blank. We raised this issue with AWS support, thinking this
must be a bug in the VTL appliance, but that turns out not to be the case.
Per AWS support, when the gateway crashes in this manner, its notion of the
current tape position is reset to the beginning of the tape. It also sets a
unit attention condition, such that the next request results in a CHECK
CONDITION status with sense key UNIT ATTENTION and asc/ascq indicating a
device reset. According to their logs the next command being sent is WRITE
FILEMARK, which results in writing an FM at the beginning of the tape,
effectively discarding its contents.
In fact, once the write fails with EIO, our software attempts to recover by
rewinding and repositioning the tape, then resuming operation. If this
fails, it attempts to rewind and reposition again, write a marker at the
end of the tape, and then unmount. It does not under any circumstances
write either data or filemarks without having successfully positioned the
tape to a known point.
What actually happens is that, since the last operation was a write, the
kernel executes an implied MTWEOF operation (which translate to a Write
Filemarks command) before the rewind that was actually requested. This
seems not entirely unreasonable, provided the tape position is known.
However, once this request fails (due to the unit attention condition), our
next rewind attempt also triggers an implied MTWEOF, which does _not_ fail
(the unit attention condition persists only until the initiator has been
notified); this is the command that unexpectedly erases the tape.
Our analysis is that the st driver is in fact completely ignoring the UNIT
ATTENTION and associated reset notification from the device. This is not a
condition that can be detected in the transport or mid-layer, as it occurs
entirely within the target and is reported only via the UNIT ATTENTION
sense key. The upper driver (i.e. st) needs to detect this indication and
reset its internal model of the device to an unknown state.
Suggested-by: Jeffrey Hutzelman <jhutz@cmu.edu>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Link: https://lore.kernel.org/r/20230822181413.1210647-1-jmeneghi@redhat.com
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Provide information in debugfs about SCSI error handling to make it easier
to debug the SCSI error handler. Additionally, report the maximum number of
retries in debugfs (.allowed).
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230822163811.219569-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most callers of scsi_rescan_device() have the scsi_device pointer readily
available. Pass a struct scsi_device pointer to scsi_rescan_device()
instead of a struct device pointer. This change prevents that a pointer to
another struct device would be passed accidentally to scsi_rescan_device().
Remove the scsi_rescan_device() declaration from the scsi_priv.h header
file since it duplicates the declaration in <scsi/scsi_host.h>.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
Cc: Mike Christie <michael.christie@oracle.com>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230822153043.4046244-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"Fix a potential array out-of-bounds in the mediatek vcodec driver"
* tag 'media/v6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vcodec: Fix potential array out-of-bounds in encoder queue_setup
|
|
These declarations were never implemented, remove them.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230822143338.19120-1-yuehaibing@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This declaration was never implemented, remove it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20230822143338.19120-1-yuehaibing@huawei.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There is no need to check whether shost_priv() returns a non-NULL value, as
the pointer returned is just an offset to the passed in parameter.
While at it replace an open coded shost_priv() instance.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20230822064817.27257-1-jgross@suse.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
used as core library"
Recent merge had a conflict in:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/macsec_fs.c
between commit:
aeb660171b06 ("net/mlx5e: fix double free in macsec_fs_tx_create_crypto_table_groups")
from Linus' tree and commit:
cb5ebe4896f9 ("net/mlx5e: Move MACsec flow steering operations to be used as core library")
from the mlx5-next tree. This was missed and the former commit
got lost, bring it back.
Fixes: 3c5066c6b0a5 ("Merge branch 'mlx5-next' of https://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20230815123725.4ef5b7b9@canb.auug.org.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The raid_component_add() function was added to the kernel tree via patch
"[SCSI] embryonic RAID class" (2005). Remove this function since it never
has had any callers in the Linux kernel. And also raid_component_release()
is only used in raid_component_add(), so it is also removed.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com>
Link: https://lore.kernel.org/r/20230822015254.184270-1-wangzhu9@huawei.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Fixes: 04b5b5cb0136 ("scsi: core: Fix possible memory leak if device_add() fails")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
John Garry <john.g.garry@oracle.com> says:
This series tidies-up libsas a bit, including:
- delete structure(s) with only one member
- delete structure members which are only ever set
- delete structure members which are never set and code which relies on
that member being set
This conflicts with the following series:
https://lore.kernel.org/linux-scsi/20230809132249.37948-1-yuehaibing@huawei.com/
Any conflict should be trivial to resolve.
Based on mkp-scsi staging at a18e81d17a7e ("scsi: ufs: ufs-pci: Add support for QEMU")
Link: https://lore.kernel.org/r/20230815115156.343535-1-john.g.garry@oracle.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Igor Pylypiv <ipylypiv@google.com> says:
This patch series plumbs libata's request for a result taskfile
(ATA_QCFLAG_RESULT_TF) through libsas to pm80xx LLDD. Other libsas LLDDs
can start using the newly added return_fis_on_success as well, if needed.
For Command Duration Limits policy 0xD (command completes without an
error) libata needs FIS in order to detect the ATA_SENSE bit and read
the Sense Data for Successful NCQ Commands log (0Fh). pm80xx HBAs do
not return FIS on success by default, hence, the driver is updated to
set the RETFIS bit (Return FIS on good completion) when requested by
libsas.
Link: https://lore.kernel.org/r/20230819213040.1101044-1-ipylypiv@google.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use a dynamic calculation to determine the shift value for the internal
timer cyclecounter that will lead to the highest precision frequency
adjustments. Previously used a constant for the shift value assuming all
devices supported by the driver had a nominal frequency of 1GHz. However,
there are devices that operate at different frequencies. The previous shift
value constant would break the PHC functionality for those devices.
Reported-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Closes: https://lore.kernel.org/netdev/20230815151507.3028503-1-vadfed@meta.com/
Fixes: 6a4010927562 ("net/mlx5: Update cyclecounter shift value to improve ptp free running mode precision")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Tested-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Saeed Mahameed <saeedm@nvidia.com>
Link: https://lore.kernel.org/r/20230821230554.236210-1-rrameshbabu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ms_hyperv_init_platform(), do not distinguish between a SNP VM with
the paravisor and a SNP VM without the paravisor.
Replace hv_isolation_type_en_snp() with
!ms_hyperv.paravisor_present && hv_isolation_type_snp().
The hv_isolation_type_en_snp() in drivers/hv/hv.c and
drivers/hv/hv_common.c can be changed to hv_isolation_type_snp() since
we know !ms_hyperv.paravisor_present is true there.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-10-decui@microsoft.com
|
|
The post_msg_page was removed in
commit 9a6b1a170ca8 ("Drivers: hv: vmbus: Remove the per-CPU post_msg_page")
However, it turns out that we need to bring it back, but only for a TDX VM
with the paravisor: in such a VM, the hyperv_pcpu_input_arg is not decrypted,
but the HVCALL_POST_MESSAGE in such a VM needs a decrypted page as the
hypercall input page: see the comments in hyperv_init() for a detailed
explanation.
Except for HVCALL_POST_MESSAGE and HVCALL_SIGNAL_EVENT, the other hypercalls
in a TDX VM with the paravisor still use hv_hypercall_pg and must use the
hyperv_pcpu_input_arg (which is encrypted in such a VM), when a hypercall
input page is used.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-8-decui@microsoft.com
|
|
The new variable hyperv_paravisor_present is set only when the VM
is a SNP/TDX VM with the paravisor running: see ms_hyperv_init_platform().
We introduce hyperv_paravisor_present because we can not use
ms_hyperv.paravisor_present in arch/x86/include/asm/mshyperv.h:
struct ms_hyperv_info is defined in include/asm-generic/mshyperv.h, which
is included at the end of arch/x86/include/asm/mshyperv.h, but at the
beginning of arch/x86/include/asm/mshyperv.h, we would already need to use
struct ms_hyperv_info in hv_do_hypercall().
We use hyperv_paravisor_present only in include/asm-generic/mshyperv.h,
and use ms_hyperv.paravisor_present elsewhere. In the future, we'll
introduce a hypercall function structure for different VM types, and
at boot time, the right function pointers would be written into the
structure so that runtime testing of TDX vs. SNP vs. normal will be
avoided and hyperv_paravisor_present will no longer be needed.
Call hv_vtom_init() when it's a VBS VM or when ms_hyperv.paravisor_present
is true, i.e. the VM is a SNP VM or TDX VM with the paravisor.
Enhance hv_vtom_init() for a TDX VM with the paravisor.
In hv_common_cpu_init(), don't decrypt the hyperv_pcpu_input_arg
for a TDX VM with the paravisor, just like we don't decrypt the page
for a SNP VM with the paravisor.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-7-decui@microsoft.com
|
|
Don't set *this_cpu_ptr(hyperv_pcpu_input_arg) before the function
set_memory_decrypted() returns, otherwise we run into this ticky issue:
For a fully enlightened TDX/SNP VM, in hv_common_cpu_init(),
*this_cpu_ptr(hyperv_pcpu_input_arg) is an encrypted page before
the set_memory_decrypted() returns.
When such a VM has more than 64 VPs, if the hyperv_pcpu_input_arg is not
NULL, hv_common_cpu_init() -> set_memory_decrypted() -> ... ->
cpa_flush() -> on_each_cpu() -> ... -> hv_send_ipi_mask() -> ... ->
__send_ipi_mask_ex() tries to call hv_do_rep_hypercall() with the
hyperv_pcpu_input_arg as the hypercall input page, which must be a
decrypted page in such a VM, but the page is still encrypted at this
point, and a fatal fault is triggered.
Fix the issue by setting *this_cpu_ptr(hyperv_pcpu_input_arg) after
set_memory_decrypted(): if the hyperv_pcpu_input_arg is NULL,
__send_ipi_mask_ex() returns HV_STATUS_INVALID_PARAMETER immediately,
and hv_send_ipi_mask() falls back to orig_apic.send_IPI_mask(),
which can use x2apic_send_IPI_all(), which may be slightly slower than
the hypercall but still works correctly in such a VM.
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-6-decui@microsoft.com
|
|
Add Hyper-V specific code so that a fully enlightened TDX guest (i.e.
without the paravisor) can run on Hyper-V:
Don't use hv_vp_assist_page. Use GHCI instead.
Don't try to use the unsupported HV_REGISTER_CRASH_CTL.
Don't trust (use) Hyper-V's TLB-flushing hypercalls.
Don't use lazy EOI.
Share the SynIC Event/Message pages with the hypervisor.
Don't use the Hyper-V TSC page for now, because non-trivial work is
required to share the page with the hypervisor.
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-4-decui@microsoft.com
|
|
A fully enlightened TDX guest on Hyper-V (i.e. without the paravisor) only
uses the GHCI call rather than hv_hypercall_pg. Do not initialize
hypercall_pg for such a guest.
In hv_common_cpu_init(), the hyperv_pcpu_input_arg page needs to be
decrypted in such a guest.
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-3-decui@microsoft.com
|
|
No logic change to SNP/VBS guests.
hv_isolation_type_tdx() will be used to instruct a TDX guest on Hyper-V to
do some TDX-specific operations, e.g. for a fully enlightened TDX guest
(i.e. without the paravisor), hv_do_hypercall() should use
__tdx_hypercall() and such a guest on Hyper-V should handle the Hyper-V
Event/Message/Monitor pages specially.
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Tianyu Lan <tiala@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20230824080712.30327-2-decui@microsoft.com
|
|
Merge padding, shrinking "struct memdev" from 32 bytes to 24 bytes
on 64-bit.
Link: https://lkml.kernel.org/r/fe4d62ab-2427-4635-b9f4-467853fb63e3@p183
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Introduce the crash_hotplug attribute for memory and CPUs for use by
userspace. These attributes directly facilitate the udev rule for
managing userspace re-loading of the crash kernel upon hot un/plug
changes.
For memory, expose the crash_hotplug attribute to the
/sys/devices/system/memory directory. For example:
# udevadm info --attribute-walk /sys/devices/system/memory/memory81
looking at device '/devices/system/memory/memory81':
KERNEL=="memory81"
SUBSYSTEM=="memory"
DRIVER==""
ATTR{online}=="1"
ATTR{phys_device}=="0"
ATTR{phys_index}=="00000051"
ATTR{removable}=="1"
ATTR{state}=="online"
ATTR{valid_zones}=="Movable"
looking at parent device '/devices/system/memory':
KERNELS=="memory"
SUBSYSTEMS==""
DRIVERS==""
ATTRS{auto_online_blocks}=="offline"
ATTRS{block_size_bytes}=="8000000"
ATTRS{crash_hotplug}=="1"
For CPUs, expose the crash_hotplug attribute to the
/sys/devices/system/cpu directory. For example:
# udevadm info --attribute-walk /sys/devices/system/cpu/cpu0
looking at device '/devices/system/cpu/cpu0':
KERNEL=="cpu0"
SUBSYSTEM=="cpu"
DRIVER=="processor"
ATTR{crash_notes}=="277c38600"
ATTR{crash_notes_size}=="368"
ATTR{online}=="1"
looking at parent device '/devices/system/cpu':
KERNELS=="cpu"
SUBSYSTEMS==""
DRIVERS==""
ATTRS{crash_hotplug}=="1"
ATTRS{isolated}==""
ATTRS{kernel_max}=="8191"
ATTRS{nohz_full}==" (null)"
ATTRS{offline}=="4-7"
ATTRS{online}=="0-3"
ATTRS{possible}=="0-7"
ATTRS{present}=="0-3"
With these sysfs attributes in place, it is possible to efficiently
instruct the udev rule to skip crash kernel reloading for kernels
configured with crash hotplug support.
For example, the following is the proposed udev rule change for RHEL
system 98-kexec.rules (as the first lines of the rule file):
# The kernel updates the crash elfcorehdr for CPU and memory changes
SUBSYSTEM=="cpu", ATTRS{crash_hotplug}=="1", GOTO="kdump_reload_end"
SUBSYSTEM=="memory", ATTRS{crash_hotplug}=="1", GOTO="kdump_reload_end"
When examined in the context of 98-kexec.rules, the above rules test if
crash_hotplug is set, and if so, the userspace initiated
unload-then-reload of the crash kernel is skipped.
CPU and memory checks are separated in accordance with CONFIG_HOTPLUG_CPU
and CONFIG_MEMORY_HOTPLUG kernel config options. If an architecture
supports, for example, memory hotplug but not CPU hotplug, then the
/sys/devices/system/memory/crash_hotplug attribute file is present, but
the /sys/devices/system/cpu/crash_hotplug attribute file will NOT be
present. Thus the udev rule skips userspace processing of memory hot
un/plug events, but the udev rule will evaluate false for CPU events, thus
allowing userspace to process CPU hot un/plug events (ie the
unload-then-reload of the kdump capture kernel).
Link: https://lkml.kernel.org/r/20230814214446.6659-5-eric.devolder@oracle.com
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Sourabh Jain <sourabhjain@linux.ibm.com>
Acked-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Baoquan He <bhe@redhat.com>
Cc: Akhil Raj <lf32.dev@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Weißschuh <linux@weissschuh.net>
Cc: Valentin Schneider <vschneid@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add the missing MODULE_DESCRIPTION() to avoid warnings such as:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/ata/sata_gemini.o
when compiling with W=1.
Fixes: be4e456ed3a5 ("ata: Add driver for Faraday Technology FTIDE010")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add the missing MODULE_DESCRIPTION() to avoid warnings such as:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/ata/pata_ftide010.o
when compiling with W=1.
Fixes: be4e456ed3a5 ("ata: Add driver for Faraday Technology FTIDE010")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove the unnecessary encoding of page order into an enum and pass the
page order directly. That lets us get rid of pe_order().
The switch constructs have to be changed to if/else constructs to prevent
GCC from warning on builds with 3-level page tables where PMD_ORDER and
PUD_ORDER have the same value.
If you are looking at this commit because your driver stopped compiling,
look at the previous commit as well and audit your driver to be sure it
doesn't depend on mmap_lock being held in its ->huge_fault method.
[willy@infradead.org: use "order %u" to match the (non dev_t) style]
Link: https://lkml.kernel.org/r/ZOUYekbtTv+n8hYf@casper.infradead.org
Link: https://lkml.kernel.org/r/20230818202335.2739663-4-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
