| Age | Commit message (Collapse) | Author |
|---|
|
Add missing external device timeout notification. Recognize
it as a failed LNI signal from the 8051 firmware.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is a a bug in defered ack stuff that causes a race with the
destroy of a QP.
A packet causes a defered ack to be pended by putting the QP
into an rcd queue.
A return from the driver interrupt processing will process that rcd
queue of QPs and attempt to do a direct send of the ack. At this
point no locks are held and the above QP could now be put in the reset
state in the qp destroy logic. A refcount protects the QP while it
is in the rcd queue so it isn't going anywhere yet.
If the direct send fails to allocate a pio buffer,
hfi1_schedule_send() is called to trigger sending an ack from the
send engine. There is no state test in that code path.
The refcount is then dropped from the driver.c caller
potentially allowing the qp destroy to continue from its
refcount wait in parallel with the workqueue scheduling of the qp.
Cc: stable@vger.kernel.org
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Prevent over-reading the SGE length by using byte
reads for non quad-word reads.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In certain cases, if the tail of an SGE is not
8-byte aligned, bytes beyond the end to an 8-byte
alignment can be read. Change the copy routine
to avoid the over-read. Instead, stop on the final
whole quad-word, then read the remaining bytes.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Allow a longer timeout for i2c due to clock stretching and
inaccurate jiffy timing when under a spin lock. This timeout
is consistent with other i2c-algo-bit users.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The ib_write_bw test allows using up to 16384 QPs. When a relatively
large number of QPs (within that range) is used, the test can fail
because the number of CQ entries needed exceeds the limit set by the
driver.
This patch increases the default setting of max_cqes from 0x2FFFF
(196607) to 0x2FFFFF(3145727), which is sufficient to cover the
maximum number needed by the ib_write_bw test (2097152). The default
setting of max_qps is also increased from 16384 to 32768 to allow
the test to run successfully with 16383 or 16384 QPs.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The FM should have full control to set the pkeys in the
driver pkey table. Remove filtering done by the driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
There is no need to have a global qpt_mask as that does not support the
multiple chip model which qib has. Instead rely on the value which
exists already in the device data (dd).
Fixes: 898fa52b4ac3 "IB/qib: Remove qpn, qp tables and related variables from qib"
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This allows for adding additional pages of adaptive pio
opcode control including manufacturer specific ones.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
This patch adds lockdep asserts in key code paths for
insuring lock correctness.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Add an rvt_qp_init() to initialize specific
common fields as the qp is created or reset.
The routine is shared by the rvt_reset_qp() and
the rvt_create_qp().
The intent is that lock dep assertions will only
appear in the rvt_reset_qp().
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The reset calldown is misplaced.
It should only be called in the code that actually
transitions the QP to reset.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The call is misplaced in the reset calldown function
and causes issues with lockdep assertions that are to
be added.
Fixes: Commit a2c2d608957c ("staging/rdma/hfi1: Remove create_qp functionality")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The __must_hold() is sufficent to correct the sparse
context imbalance inside a function.
Per Documentation/sparse.txt:
__must_hold - The specified lock is held on function entry and exit.
Fixes: Commit c0a67f6ba356 ("IB/rdmavt: Annotate rvt_reset_qp()")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Existing locking scheme in affinity.c file using the
&node_affinity.lock spinlock is not very elegant.
We acquire the lock to get hfi1_affinity_node entry,
unlock, and then use the entry without the lock held.
With more functions being added, which access and
modify the entries, this can lead to race conditions.
This patch makes this locking scheme more consistent.
It changes the spinlock to mutex. Since all the code
is executed in a user process context there is no need
for a spinlock. This also allows to keep the lock
not only while we look up for the node affinity entry,
but over the whole section where the entry is being used.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The dma_XXX API functions return bus addresses which are
physical addresses when IOMMU is disabled. Buffer
mapping to user-space is done via remap_pfn_range() with PFN
based on bus address instead of physical. This results in
wrong pages being mapped to user-space when IOMMU is enabled.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tymoteusz Kielan <tymoteusz.kielan@intel.com>
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Each user SDMA request coming into the driver may contain multiple packets.
Each user packet may use multiple SDMA descriptors to fill the send buffer.
The field seqsubmitted in struct user_sdma_request counts the number of
user packets submitted to an SDMA engine. Sometimes, the intermediate count
may not be updated properly. However, once all the packets' descriptors
are successfully submitted to the SDMA engine, the final count is updated
correctly. But, if only some of the packets are submitted to the engine due
to an error, the intermediate count doesn't reflect the partial number of
packets submitted to the SDMA engine. This can cause a hang later in the
code as the count of packets submitted to the SDMA engine doesn't match the
the count of packets processed by the SDMA engine.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
All calls to tune_serdes and start_link are paired. Move
tune_serdes inside start_link.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Use common header file structs, defines, and accessors
in the drivers. The old declarations are removed.
The repositioning of the includes allows for the removal
of hfi1_message_header and replaces its use with ib_header.
Also corrected are two issues with set_armed_to_active():
- The "packet" parameter is now a pointer as it should have been
- The etype is validated to insure that the header is correct
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
* pm-devfreq:
PM / devfreq: rk3399_dmc: Remove explictly regulator_put call in .remove
PM / devfreq: rockchip: add PM_DEVFREQ_EVENT dependency
partial revert of "PM / devfreq: Add COMPILE_TEST for build coverage"
PM / devfreq: rockchip: add devfreq driver for rk3399 dmc
Documentation: bindings: add dt documentation for rk3399 dmc
PM / devfreq: event: support rockchip dfi controller
Documentation: bindings: add dt documentation for dfi controller
PM / devfreq: event: remove duplicate devfreq_event_get_drvdata()
PM / devfreq: fix Kconfig indent style
PM / devfreq: Add COMPILE_TEST for build coverage
PM / devfreq: exynos-ppmu: remove unneeded of_node_put()
* pm-sleep:
PM / Hibernate: allow hibernation with PAGE_POISONING_ZERO
PM / sleep: enable suspend-to-idle even without registered suspend_ops
PM / sleep: Increase default DPM watchdog timeout to 120
|
|
* pm-cpuidle:
ARM: cpuidle: Fix error return code
* pm-opp:
PM / OPP: Don't support OPP if it provides supported-hw but platform does not
PM / OPP: avoid maybe-uninitialized warning
* pm-avs:
PM / AVS: SmartReflex: Neaten logging
|
|
* pm-cpufreq: (24 commits)
cpufreq: st: add missing \n to end of dev_err message
cpufreq: kirkwood: add missing \n to end of dev_err messages
cpufreq: CPPC: Avoid overflow when calculating desired_perf
cpufreq: ti: Use generic platdev driver
cpufreq: intel_pstate: Add io_boost trace
cpufreq: intel_pstate: Use IOWAIT flag in Atom algorithm
cpufreq: schedutil: Add iowait boosting
cpufreq / sched: SCHED_CPUFREQ_IOWAIT flag to indicate iowait condition
cpufreq: CPPC: Force reporting values in KHz to fix user space interface
cpufreq: create link to policy only for registered CPUs
intel_pstate: constify local structures
cpufreq: dt: Support governor tunables per policy
cpufreq: dt: Update kconfig description
cpufreq: dt: Remove unused code
MAINTAINERS: Add Documentation/cpu-freq/
cpufreq: dt: Add support for r8a7792
cpufreq / sched: ignore SMT when determining max cpu capacity
cpufreq: Drop unnecessary check from cpufreq_policy_alloc()
ARM: multi_v7_defconfig: Don't attempt to enable schedutil governor as module
ARM: exynos_defconfig: Don't attempt to enable schedutil governor as module
...
|
|
|
|
* pm-domains:
PM / Domains: Rename pm_genpd_sync_poweron|poweroff()
PM / Domains: Don't measure latency of ->power_on|off() during system PM
PM / Domains: Remove redundant system PM callbacks
PM / Domains: Simplify detaching a device from its genpd
PM / Domains: Allow holes in genpd_data.domains array
PM / Domains: Add support for removing nested PM domains by provider
PM / Domains: Add support for removing PM domains
PM / Domains: Store the provider in the PM domain structure
PM / Domains: Prepare for adding support to remove PM domains
PM / Domains: Verify the PM domain is present when adding a provider
PM / Domains: Don't expose xlate and provider helper functions
PM / Domains: Don't expose generic_pm_domain structure to clients
staging: board: Remove calls to of_genpd_get_from_provider()
ARM: EXYNOS: Remove calls to of_genpd_get_from_provider()
PM / Domains: Add new helper functions for device-tree
PM / Domains: Always enable debugfs support if available
|
|
* acpi-button:
ACPI / button: Add document for ACPI control method lid device restrictions
ACPI / button: Fix an issue in button.lid_init_state=ignore mode
* acpi-battery:
ACPI / battery: Add sysfs representation after checking _BST
* acpi-doc:
ACPI / documentation: Use recommended name in GPIO property names
|
|
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
|
|
* acpi-x86:
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
* acpi-cppc:
ACPI / CPPC: Support PCC with interrupt flag
ACPI / CPPC: Add prefix cppc to cpudata structure name
ACPI / CPPC: Add support for functional fixed hardware address
ACPI / CPPC: Don't return on CPPC probe failure
ACPI / CPPC: Allow build with ACPI_CPU_FREQ_PSS config
ACPI / CPPC: check for error bit in PCC status field
ACPI / CPPC: move all PCC related information into pcc_data
ACPI / CPPC: add sysfs support to compute delivered performance
ACPI / CPPC: set a non-zero value for transition_latency
ACPI / CPPC: support for batching CPPC requests
ACPI / CPPC: acquire pcc_lock only while accessing PCC subspace
ACPI / CPPC: restructure read/writes for efficient sys mapped reg ops
mailbox: pcc: Support HW-Reduced Communication Subspace type 2
* acpi-soc:
ACPI / APD: constify local structures
ACPI / APD: Add device HID for Vulcan SPI controller
|
|
* acpi-bus:
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPI / bus: Make acpi_get_first_physical_node() public
|
|
* acpi-sysfs:
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPI / sysfs: Use new GPE masking mechanism in GPE interface
* acpi-pci:
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / PCI: fix GIC irq model default PCI IRQ polarity
* acpi-tables:
ACPI / tables: Remove duplicated include from tables.c
ACPI / tables: do not report the number of entries ignored by acpi_parse_entries()
ACPI / tables: fix acpi_parse_entries_array() so it traverses all subtables
ACPI / tables: fix incorrect counts returned by acpi_parse_entries_array()
|
|
* acpica: (45 commits)
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPICA: Update version to 20160831
ACPICA: Tables: Tune table mutex to be a leaf lock
ACPICA: Dispatcher: Fix a mutex issue for method auto serialization
ACPICA: Namespace: Fix dynamic table loading issues
ACPICA: Namespace: Add acpi_ns_get_node_unlocked()
ACPICA: Interpreter: Fix MLC issues by switching to new term_list grammar for table loading
ACPICA: Update return value for intenal _OSI method
ACPICA: Tables: Override all 64-bit GAS fields when acpi_gbl_use32_bit_fadt_addresses is TRUE
ACPICA: Tables: Add new table events indicating table installation/uninstallation
ACPICA: Tables: Remove wrong table event macros
ACPICA: Tables: Remove acpi_tb_install_fixed_table()
ACPICA: Add a couple of casts to uthex.c
ACPICA: Cleanup for all string-to-integer conversions
ACPICA: Debugger: Add subcommand for predefined name execution
ACPICA: Update version to 20160729
ACPICA: OSL: Fix a regression that old GCC requires a workaround for strchr()
ACPICA: OSL: Cleanup the inclusion order of the compiler-specific headers
...
|
|
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One final fix before 4.8.
There was a memory leak triggered by turning scsi mq off due to the
fact that we assume on host release that the already running hosts
weren't mq based because that's the state of the global flag (even
though they were).
Fix it by tracking this on a per host host basis"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Avoid that toggling use_blk_mq triggers a memory leak
|
|
Driver was reporting invalid raw read values for MAX6675 on big
endian architectures. MAX6675 buffered mode is not affected, nor
is the MAX31855.
The driver was losing a 2 byte read value when it used a 32 bit
integer buffer to store a 16 bit big endian value. Use big endian
types to properly align buffers on big endian architectures.
Fixes following sparse endianness warnings:
warning: cast to restricted __be16
warning: cast to restricted __be32
Fixes checkpatch issue:
CHECK: No space is necessary after a cast
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Fixes: 1f25ca11d84a ("iio: temperature: add support for Maxim
thermocouple chips")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We get 2 warnings when building kernel with W=1:
drivers/dma/virt-dma.c:22:14: warning: no previous prototype for 'vchan_tx_submit' [-Wmissing-prototypes]
drivers/dma/virt-dma.c:52:5: warning: no previous prototype for 'vchan_tx_desc_free' [-Wmissing-prototypes]
In fact, these two functions are incorrectly declared in a function.
So this patch moves function declarations out of this function.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Enable the burst and data pack modes for the scatter-gather
in order to improve the throughput of the data transfers.
The improvement has been verified with MMC HS200 mode in
the DRA72 EVM using the iozone tool to compare the read
throughput (in kB/s) with and without burst/pack for
different reclens (in kB).
With
reclen Baseline sDMA burst/pack
------ -------- ---------------
64 46568 50820
128 57564 63413
256 65634 74937
512 72427 83483
1024 74563 84504
2048 76265 86079
4096 78045 87335
8192 78989 88154
16384 81265 91034
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"One small change to make joydev (which is used by older games) to bind
to devices that export Z axis but not X or Y (such as TRC rudder)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - recognize devices with Z axis as joysticks
|
|
In preparation for enabling multiple namespaces per pmem region, convert
the label tracking to use a linked list. In particular this will allow
select_pmem_id() to move labels from the unvalidated state to the
validated state. Currently we only track one validated set per-region.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Before we add more libnvdimm-private fields to nd_mapping make it clear
which parameters are input vs libnvdimm internals. Use struct
nd_mapping_desc instead of struct nd_mapping in nd_region_desc and make
struct nd_mapping private to libnvdimm.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Existing implemenetation writes to all the flush hint addresses for a
given ND region. This is not necessary as the flushes are per imc and
not per DIMM. Search the mappings and clear out the duplicates at init
to avoid multiple flush to the same imc.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
nvdimm_clear_poison cleared the user-visible badblocks, and sent
commands to the NVDIMM to clear the areas marked as 'poison', but it
neglected to clear the same areas from the internal poison_list which is
used to marshal ARS results before sorting them by namespace. As a
result, once on-demand ARS functionality was added:
37b137f nfit, libnvdimm: allow an ARS scrub to be triggered on demand
A scrub triggered from either sysfs or an MCE was found to be adding
stale entries that had been cleared from gendisk->badblocks, but were
still present in nvdimm_bus->poison_list. Additionally, the stale entries
could be triggered into producing stale disk->badblocks by simply disabling
and re-enabling the namespace or region.
This adds the missing step of clearing poison_list entries when clearing
poison, so that it is always in sync with badblocks.
Fixes: 37b137f ("nfit, libnvdimm: allow an ARS scrub to be triggered on demand")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
pmem_do_bvec used to kmap_atomic at the begin, and only unmap at the
end. Things like nvdimm_clear_poison may want to do nvdimm subsystem
bookkeeping operations that may involve taking locks or doing memory
allocations, and we can't do that from the atomic context. Reduce the
atomic context to just what needs it - the memcpy to/from pmem.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Starting a full Address Range Scrub (ARS) on hitting a memory error
machine check exception may not always be desirable. Provide a way
through sysfs to toggle the behavior between just adding the address
(cache line) where the MCE happened to the poison list and doing a full
scrub. The former (selective insertion of the address) is done
unconditionally.
Cc: linux-acpi@vger.kernel.org
Cc: Linda Knippers <linda.knippers@hpe.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Free memory mapping, if probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In two cases when jz4780_dma_setup_hwdesc fails, there is a memory
leak on the allocated desc and associated DMA pools on the error
exit return path. Fix this by free'ing the resources before
returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Currently U300_DMA_CHANNELS is set to 40, meaning that the shift of 1 can
be more than 32 places, which leads to a 32 bit integer overflow. Fix this
by using 1ULL instead of 1 before shifting it. Also add braces on the
for-loop to keep with coding style conventions.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If edma_read_slot() gets an invalid argument, it does not set a result,
as found by "gcc -Wmaybe-uninitialized"
drivers/dma/edma.c: In function 'dma_ccerr_handler':
drivers/dma/edma.c:1499:21: error: 'p.a_b_cnt' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/dma/edma.c:1499:21: error: 'p.ccnt' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (p.a_b_cnt == 0 && p.ccnt == 0) {
If we change the function to return an error in this case, we can handle
the failure more gracefully and treat this the same way as a null slot
that we already catch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
'spi/topic/txx9' and 'spi/topic/xlp' into spi-next
|
|
'spi/topic/sh-msiof', 'spi/topic/spidev-test' and 'spi/topic/st-ssc4' into spi-next
|
|
'spi/topic/pxa2xx' and 'spi/topic/qup' into spi-next
|
|
'spi/topic/jcore', 'spi/topic/loopback' and 'spi/topic/meson' into spi-next
|
