summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2021-04-21rtw88: refine napi deinit flowPo-Hao Huang
We used to stop napi before disabling irqs. And it turns out to cause some problem when we try to stop device while interrupt arrives. To safely stop pci, we do three steps: 1. disable interrupt 2. synchronize_irq 3. stop_napi Since step 2 and 3 may not finish as expected when interrupt is enabled, use rtwpci->running to decide whether interrupt should be re-enabled at the time. Fixes: 9e2fd29864c5 ("rtw88: add napi support") Signed-off-by: Po-Hao Huang <phhuang@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210415084703.27255-4-pkshih@realtek.com
2021-04-21rtw88: Fix potential unrecoverable tx queue stopYu-Yen Ting
If there are lots of packets to be transmitted, the driver would check whether the available descriptors are sufficient according the read/write point of tx queue. Once the available descriptor is not enough, ieee80211_stop_queue is called. TX ISR, meanwhile, is releasing the tx resources after the packets are transmitted. This routine may call ieee80211_wake_queue by checking the available descriptor. The potential queue stop problem would occur when the tx queue is stopped due to the heavy traffic. Then thare is no chance to wake the queue up because the read point is not updated immediately, as a result, no more packets coulde be transmitted in this queue. This patch makes sure the ieee80211_wake_queue could be called properly and avoids the race condition when ring->r.rp, ring->queue_stopped are updated. Signed-off-by: Yu-Yen Ting <steventing@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210415084703.27255-3-pkshih@realtek.com
2021-04-21rtw88: 8821c: Don't set RX_FLAG_DECRYPTED if packet has no encryptionGuo-Feng Fan
The value of GET_RX_DESC_SWDEC() indicates that if this RX packet requires software decryption or not. And software decryption is required when the packet was encrypted and the hardware failed to decrypt it. So, GET_RX_DESC_SWDEC() is negative does not mean that this packet is decrypted, it might just have no encryption at all. To actually see if the packet is decrypted, driver needs to further check if the hardware has successfully decrypted it, with a specific type of encryption algorithm. Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210415084703.27255-2-pkshih@realtek.com
2021-04-21rtw88: 8822c: debug: allow debugfs to enable/disable TXGAPKGuo-Feng Fan
Use "cat dm_cap" to show all features; where, prefix +/- means feature is enabled/disabled: $ cat dm_cap DM capability 0x00000002 ( 1) +TXGAPK To control dm_cap: use "echo +1 > dm_cap" to enable TXGAPK use "echo -1 > dm_cap" to disable TXGAPK Below is an example to disable TXGAPK. $ echo -1 > dm_cap $ cat dm_cap DM capability 0x00000000 ( 1) -TXGAPK Below is an example to show TXGAPK status $ echo 1 > dm_cap; cat dm_cap ( 1) +TXGAPK path 0: 0x56 = 0x88c89 [TXGAPK] offset 1 0 [TXGAPK] offset 1 1 [TXGAPK] offset 1 2 [TXGAPK] offset 1 3 [TXGAPK] offset 0 4 [TXGAPK] offset 0 5 [TXGAPK] offset 0 6 [TXGAPK] offset 0 7 [TXGAPK] offset 0 8 [TXGAPK] offset 0 9 path 1: 0x56 = 0x89c89 [TXGAPK] offset 1 0 [TXGAPK] offset 1 1 [TXGAPK] offset 1 2 [TXGAPK] offset 1 3 [TXGAPK] offset 0 4 [TXGAPK] offset 0 5 [TXGAPK] offset 0 6 [TXGAPK] offset 0 7 [TXGAPK] offset 0 8 [TXGAPK] offset 0 9 Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210419003748.3224-4-pkshih@realtek.com
2021-04-21rtw88: 8822c: Add gap-k calibration to improve long range performanceGuo-Feng Fan
gap-k is a calibration mechanism to eliminate power gaps between two nearly rate groups. This mechanism improves performance in long range test by applying proper power value to those rate groups which have nonlinear power gap. Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210419003748.3224-3-pkshih@realtek.com
2021-04-21rtw88: 8822c: reorder macro position according to the register numberGuo-Feng Fan
This patch doesn't change logic at all, just a refactor patch. 1. Move BIT MASK and BIT definition along with the register definition 2. Remove redundant definition 3. Align macros with Tab key Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com> Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210419003748.3224-2-pkshih@realtek.com
2021-04-20net: wwan: mhi_wwan_ctrl: Fix RX buffer starvationLoic Poulain
The mhi_wwan_rx_budget_dec function is supposed to return true if RX buffer budget has been successfully decremented, allowing to queue a new RX buffer for transfer. However the current implementation is broken when RX budget is '1', in which case budget is decremented but false is returned, preventing to requeue one buffer, and leading to RX buffer starvation. Fixes: fa588eba632d ("net: Add Qcom WWAN control driver") Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: davinci_emac: Fix incorrect masking of tx and rx error channelColin Ian King
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels) are incorrect and always lead to a zero result. The mask values are currently the incorrect post-right shifted values, fix this by setting them to the currect values. (I double checked these against the TMS320TCI6482 data sheet, section 5.30, page 127 to ensure I had the correct mask values for the TXERRCH and RXERRCH fields in the MACSTATUS register). Addresses-Coverity: ("Operands don't affect result") Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: marvell: prestera: fix port event handling on initVadym Kochan
For some reason there might be a crash during ports creation if port events are handling at the same time because fw may send initial port event with down state. The crash points to cancel_delayed_work() which is called when port went is down. Currently I did not find out the real cause of the issue, so fixed it by cancel port stats work only if previous port's state was up & runnig. The following is the crash which can be triggered: [ 28.311104] Unable to handle kernel paging request at virtual address 000071775f776600 [ 28.319097] Mem abort info: [ 28.321914] ESR = 0x96000004 [ 28.324996] EC = 0x25: DABT (current EL), IL = 32 bits [ 28.330350] SET = 0, FnV = 0 [ 28.333430] EA = 0, S1PTW = 0 [ 28.336597] Data abort info: [ 28.339499] ISV = 0, ISS = 0x00000004 [ 28.343362] CM = 0, WnR = 0 [ 28.346354] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000100bf7000 [ 28.352842] [000071775f776600] pgd=0000000000000000, p4d=0000000000000000 [ 28.359695] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 28.365310] Modules linked in: prestera_pci(+) prestera uio_pdrv_genirq [ 28.372005] CPU: 0 PID: 1291 Comm: kworker/0:1H Not tainted 5.11.0-rc4 #1 [ 28.378846] Hardware name: DNI AmazonGo1 A7040 board (DT) [ 28.384283] Workqueue: prestera_fw_wq prestera_fw_evt_work_fn [prestera_pci] [ 28.391413] pstate: 60000085 (nZCv daIf -PAN -UAO -TCO BTYPE=--) [ 28.397468] pc : get_work_pool+0x48/0x60 [ 28.401442] lr : try_to_grab_pending+0x6c/0x1b0 [ 28.406018] sp : ffff80001391bc60 [ 28.409358] x29: ffff80001391bc60 x28: 0000000000000000 [ 28.414725] x27: ffff000104fc8b40 x26: ffff80001127de88 [ 28.420089] x25: 0000000000000000 x24: ffff000106119760 [ 28.425452] x23: ffff00010775dd60 x22: ffff00010567e000 [ 28.430814] x21: 0000000000000000 x20: ffff80001391bcb0 [ 28.436175] x19: ffff00010775deb8 x18: 00000000000000c0 [ 28.441537] x17: 0000000000000000 x16: 000000008d9b0e88 [ 28.446898] x15: 0000000000000001 x14: 00000000000002ba [ 28.452261] x13: 80a3002c00000002 x12: 00000000000005f4 [ 28.457622] x11: 0000000000000030 x10: 000000000000000c [ 28.462985] x9 : 000000000000000c x8 : 0000000000000030 [ 28.468346] x7 : ffff800014400000 x6 : ffff000106119758 [ 28.473708] x5 : 0000000000000003 x4 : ffff00010775dc60 [ 28.479068] x3 : 0000000000000000 x2 : 0000000000000060 [ 28.484429] x1 : 000071775f776600 x0 : ffff00010775deb8 [ 28.489791] Call trace: [ 28.492259] get_work_pool+0x48/0x60 [ 28.495874] cancel_delayed_work+0x38/0xb0 [ 28.500011] prestera_port_handle_event+0x90/0xa0 [prestera] [ 28.505743] prestera_evt_recv+0x98/0xe0 [prestera] [ 28.510683] prestera_fw_evt_work_fn+0x180/0x228 [prestera_pci] [ 28.516660] process_one_work+0x1e8/0x360 [ 28.520710] worker_thread+0x44/0x480 [ 28.524412] kthread+0x154/0x160 [ 28.527670] ret_from_fork+0x10/0x38 [ 28.531290] Code: a8c17bfd d50323bf d65f03c0 9278dc21 (f9400020) [ 28.537429] ---[ end trace 5eced933df3a080b ]--- Fixes: 501ef3066c89 ("net: marvell: prestera: Add driver for Prestera family ASIC devices") Signed-off-by: Vadym Kochan <vkochan@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: at803x: fix probe error if copper page is selectedMichael Walle
The commit c329e5afb42f ("net: phy: at803x: select correct page on config init") selects the copper page during probe. This fails if the copper page was already selected. In this case, the value of the copper page (which is 1) is propagated through phy_restore_page() and is finally returned for at803x_probe(). Fix it, by just using the at803x_page_write() directly. Also in case of an error, the regulator is not disabled and leads to a WARN_ON() when the probe fails. This couldn't happen before, because at803x_parse_dt() was the last call in at803x_probe(). It is hard to see, that the parse_dt() actually enables the regulator. Thus move the regulator_enable() to the probe function and undo it in case of an error. Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: David Bauer <mail@david-bauer.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: mana: remove redundant initialization of variable errColin Ian King
The variable err is being initialized with a value that is never read and it is being updated later with a new value. The initialization is redundant and can be removed Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20sfc: ef10: fix TX queue lookup in TX event handlingEdward Cree
We're starting from a TXQ label, not a TXQ type, so efx_channel_get_tx_queue() is inappropriate. This worked by chance, because labels and types currently match on EF10, but we shouldn't rely on that. Fixes: 12804793b17c ("sfc: decouple TXQ type from label") Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20sfc: farch: fix TX queue lookup in TX event handlingEdward Cree
We're starting from a TXQ label, not a TXQ type, so efx_channel_get_tx_queue() is inappropriate (and could return NULL, leading to panics). Fixes: 12804793b17c ("sfc: decouple TXQ type from label") Cc: stable@vger.kernel.org Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20sfc: farch: fix TX queue lookup in TX flush done handlingEdward Cree
We're starting from a TXQ instance number ('qid'), not a TXQ type, so efx_get_tx_queue() is inappropriate (and could return NULL, leading to panics). Fixes: 12804793b17c ("sfc: decouple TXQ type from label") Reported-by: Trevor Hemsley <themsley@voiceflex.com> Cc: stable@vger.kernel.org Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20virtio-net: fix use-after-free in page_to_skb()Eric Dumazet
KASAN/syzbot had 4 reports, one of them being: BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:191 [inline] BUG: KASAN: slab-out-of-bounds in page_to_skb+0x5cf/0xb70 drivers/net/virtio_net.c:480 Read of size 12 at addr ffff888014a5f800 by task systemd-udevd/8445 CPU: 0 PID: 8445 Comm: systemd-udevd Not tainted 5.12.0-rc8-next-20210419-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:79 [inline] dump_stack+0x141/0x1d7 lib/dump_stack.c:120 print_address_description.constprop.0.cold+0x5b/0x2f8 mm/kasan/report.c:233 __kasan_report mm/kasan/report.c:419 [inline] kasan_report.cold+0x7c/0xd8 mm/kasan/report.c:436 check_region_inline mm/kasan/generic.c:180 [inline] kasan_check_range+0x13d/0x180 mm/kasan/generic.c:186 memcpy+0x20/0x60 mm/kasan/shadow.c:65 memcpy include/linux/fortify-string.h:191 [inline] page_to_skb+0x5cf/0xb70 drivers/net/virtio_net.c:480 receive_mergeable drivers/net/virtio_net.c:1009 [inline] receive_buf+0x2bc0/0x6250 drivers/net/virtio_net.c:1119 virtnet_receive drivers/net/virtio_net.c:1411 [inline] virtnet_poll+0x568/0x10b0 drivers/net/virtio_net.c:1516 __napi_poll+0xaf/0x440 net/core/dev.c:6962 napi_poll net/core/dev.c:7029 [inline] net_rx_action+0x801/0xb40 net/core/dev.c:7116 __do_softirq+0x29b/0x9fe kernel/softirq.c:559 invoke_softirq kernel/softirq.c:433 [inline] __irq_exit_rcu+0x136/0x200 kernel/softirq.c:637 irq_exit_rcu+0x5/0x20 kernel/softirq.c:649 common_interrupt+0xa4/0xd0 arch/x86/kernel/irq.c:240 Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Cc: Jason Wang <jasowang@redhat.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: virtualization@lists.linux-foundation.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20phy: nxp-c45-tja11xx: fix phase offset calculationRadu Pirea (NXP OSS)
Fix phase offset calculation. Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: enetc: automatically select IERB moduleMichael Walle
Now that enetc supports flow control we have to make sure the settings in the IERB are correct. Therefore, we actually depend on the enetc-ierb module. Previously it was possible that this module was disabled while the enetc was enabled. Fix it by automatically select the enetc-ierb module. Fixes: e7d48e5fbf30 ("net: enetc: add a mini driver for the Integrated Endpoint Register Block") Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20virtio-net: restrict build_skb() use to some archesEric Dumazet
build_skb() is supposed to be followed by skb_reserve(skb, NET_IP_ALIGN), so that IP headers are word-aligned. (Best practice is to reserve NET_IP_ALIGN+NET_SKB_PAD, but the NET_SKB_PAD part is only a performance optimization if tunnel encaps are added.) Unfortunately virtio_net has not provisioned this reserve. We can only use build_skb() for arches where NET_IP_ALIGN == 0 We might refine this later, with enough testing. Fixes: fb32856b16ad ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Cc: Jason Wang <jasowang@redhat.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: virtualization@lists.linux-foundation.org Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: wwan: Fix bit ops double shiftLoic Poulain
bit operation helpers such as test_bit, clear_bit, etc take bit position as parameter and not value. Current usage causes double shift => BIT(BIT(0)). Fix that in wwan_core and mhi_wwan_ctrl. Fixes: 9a44c1cc6388 ("net: Add a WWAN subsystem") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: dsa: mv88e6xxx: Allow dynamic reconfiguration of tag protocolTobias Waldekranz
For devices that supports both regular and Ethertyped DSA tags, allow the user to change the protocol. Additionally, because there are ethernet controllers that do not handle regular DSA tags in all cases, also allow the protocol to be changed on devices with undocumented support for EDSA. But, in those cases, make sure to log the fact that an undocumented feature has been enabled. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: dsa: mv88e6xxx: Mark chips with undocumented EDSA tag supportTobias Waldekranz
All devices are capable of using regular DSA tags. Support for Ethertyped DSA tags sort into three categories: 1. No support. Older chips fall into this category. 2. Full support. Datasheet explicitly supports configuring the CPU port to receive FORWARDs with a DSA tag. 3. Undocumented support. Datasheet lists the configuration from category 2 as "reserved for future use", but does empirically behave like a category 2 device. So, instead of listing the one true protocol that should be used by a particular chip, specify the level of support for EDSA (support for regular DSA is implicit on all chips). As before, we use EDSA for all chips that fully supports it. In upcoming changes, we will use this information to support dynamically changing the tag protocol. Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20Merge tag 'mac80211-next-for-net-next-2021-04-20' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Another set of updates, all over the map: * set sk_pacing_shift for 802.3->802.11 encap offload * some monitor support for 802.11->802.3 decap offload * HE (802.11ax) spec updates * userspace API for TDLS HE support * along with various other small features, cleanups and fixups ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Index future FIFOs by band numberPetr Machata
mlxsw used to hold an array of qdiscs indexed by the TC number. In the previous patch, it was changed to allocate child qdiscs dynamically, and they are now indexed by band number. Follow suit with the array of future FIFOs. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Allocate child qdiscs dynamicallyPetr Machata
Instead of keeping qdiscs in globally-preallocated arrays, introduce a per-qdisc-kind value num_classes, and then allocate the necessary child qdiscs (if any) based on that value. Since now dynamic allocation is involved, mlxsw_sp_qdisc_replace() gets messy enough that it is worth it to split it to two cases: a new qdisc allocation and a change of existing qdisc. (Note that the change also includes what TC formally calls replace, if the qdisc kind is the same.) Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Guard all qdisc accesses with a lockPetr Machata
The FIFO handler currently guards accesses to the future FIFO tracking by asserting RTNL. In the future, the changes to the qdisc state will be more thorough, so other qdiscs will need this guarding is as well. In order to not further the RTNL infestation, instead convert to a custom lock that will guard accesses to the qdisc state. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Track children per qdiscPetr Machata
mlxsw currently allows a two-level structure of qdiscs: the root and possibly a number of children. In order to support offloading more general qdisc trees, introduce to struct mlxsw_sp_qdisc a pointer to child qdiscs. Refer to the child qdiscs through this pointer, instead of going through the tclass_qdiscs in qdisc_state. Additionally introduce a field num_classes, which holds number of given qdisc's children. Also introduce a generic function for walking qdisc trees. Rewrite mlxsw_sp_qdisc_find() and _find_by_handle() to use the generic walker. For now, keep the qdisc_state.tclass_qdisc, and just point root_qdiscs's children to this array. Following patches will make the allocation dynamic. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Promote backlog reduction to mlxsw_sp_qdisc_destroy()Petr Machata
When a qdisc is removed, it is necessary to update the backlog value at its parent--unless the qdisc is at root position. RED, TBF and FIFO all do that, each separately. Since all of them need to do this, just promote the operation directly to mlxsw_sp_qdisc_destroy(), instead of deferring it to individual destructors. Since FIFO dtor thus becomes trivial, remove it. Add struct mlxsw_sp_qdisc.parent to point at the parent qdisc. This will be handy later as deeper structures are offloaded. Use the parent qdisc to find the chain of parents whose backlog value needs to be updated. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Track tclass_num as int, not u8Petr Machata
tclass_num is just a number, a value that would be ordinarily passed around as an int. (Which is unlike a u8 prio_bitmap.) In several places, tclass_num already is an int. Convert the remaining instances. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Drop an always-true conditionPetr Machata
The function mlxsw_sp_qdisc_compare() is invoked a couple lines above this check, which will bounce any requests where this condition does not hold. Therefore drop it. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Simplify mlxsw_sp_qdisc_compare()Petr Machata
The purpose of this function is to filter out events that are related to qdiscs that are not offloaded, or are not offloaded anymore. But the function is unnecessarily thorough: - mlxsw_sp_qdisc pointer is never NULL in the context where it is called - Two qdiscs with the same handle will never have different types. Even when replacing one qdisc with another in the same class, Linux will not permit handle reuse unless the qdisc type also matches. Simplify the function by omitting these two unnecessary conditions. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20mlxsw: spectrum_qdisc: Drop one argument from check_params callbackPetr Machata
The mlxsw_sp_qdisc argument is not used in any of the actual callbacks. Drop it. Signed-off-by: Petr Machata <petrm@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20korina: Fix build.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: marvell: add support for Amethyst internal PHYMarek Behún
Add support for Amethyst internal PHY. The only difference from Peridot is HWMON. Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: dsa: mv88e6xxx: simulate Amethyst PHY model numberMarek Behún
Amethyst internal PHYs also report empty model number in MII_PHYSID2. Fill in switch product number, as is done for Topaz and Peridot. Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: marvell: use assignment by bitwise AND operatorMarek Behún
Use the &= operator instead of ret = ret & ... Signed-off-by: Marek Behún <kabel@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: marvell: fix HWMON enable register for 6390Marek Behún
Register 27_6.15:14 has the following description in 88E6393X documentation: Temperature Sensor Enable 0x0 - Sample every 1s 0x1 - Sense rate decided by bits 10:8 of this register 0x2 - Use 26_6.5 (One shot Temperature Sample) to enable 0x3 - Disable This is compatible with how the 6390 code uses this register currently, but the 6390 code handles it as two 1-bit registers (somewhat), instead of one register with 4 possible values. (A newer version of the 6390 documentation removed temperature sensor section completely. In an older version, the above mentioned register is reserved, although it is R/W. Since the code works, I think we can assume that it is correct.) Rename this register and define all 4 values according to 6393X documentation. Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: marvell: refactor HWMON OOP styleMarek Behún
Use a structure of Marvell PHY specific HWMON methods to reduce code duplication. Store a pointer to this structure into the PHY driver's driver_data member. Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20korina: Fix conflict with global symbol desc_empty on x86.David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20Merge tag 'mlx5-updates-2021-04-19' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2021-04-19 This patchset provides some updates to mlx5e and mlx5 SW steering drivers: 1) Tariq and Vladyslav they both provide some trivial update to mlx5e netdev. The next 12 patches in the patchset are focused toward mlx5 SW steering: 2) 3 trivial cleanup patches 3) Dynamic Flex parser support: Flex parser is a HW parser that can support protocols that are not natively supported by the HCA, such as Geneve (TLV options) and GTP-U. There are 8 such parsers, and each of them can be assigned to parse a specific set of protocols. 4) Enable matching on Geneve TLV options 5) Use Flex parser for MPLS over UDP/GRE 6) Enable matching on tunnel GTP-U and GTP-U first extension header using 7) Improved QoS for SW steering internal QPair for a better insertion rate ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: dsa: felix: disable always guard band bit for TAS configXiaoliang Yang
ALWAYS_GUARD_BAND_SCH_Q bit in TAS config register is descripted as this: 0: Guard band is implemented for nonschedule queues to schedule queues transition. 1: Guard band is implemented for any queue to schedule queue transition. The driver set guard band be implemented for any queue to schedule queue transition before, which will make each GCL time slot reserve a guard band time that can pass the max SDU frame. Because guard band time could not be set in tc-taprio now, it will use about 12000ns to pass 1500B max SDU. This limits each GCL time interval to be more than 12000ns. This patch change the guard band to be only implemented for nonschedule queues to schedule queues transition, so that there is no need to reserve guard band on each GCL. Users can manually add guard band time for each schedule queues in their configuration if they want. Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: ag71xx: make use of generic NET_SELFTESTS libraryOleksij Rempel
With this patch the ag71xx on Atheros AR9331 will able to run generic net selftests. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: fec: make use of generic NET_SELFTESTS libraryOleksij Rempel
With this patch FEC on iMX will able to run generic net selftests Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: genphy_loopback: add link speed configurationOleksij Rempel
In case of loopback, in most cases we need to disable autoneg support and force some speed configuration. Otherwise, depending on currently active auto negotiated link speed, the loopback may or may not work. This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031, AT8035, AR9331. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20net: phy: execute genphy_loopback() per default on all PHYsOleksij Rempel
The generic loopback is really generic and is defined by the 802.3 standard, we should just mandate that drivers implement a custom loopback if the generic one cannot work. Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-20drbd: Fix fall-through warnings for ClangGustavo A. R. Silva
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple of warnings by explicitly adding a break statement instead of just letting the code fall through to the next, and by adding a fallthrough pseudo-keyword in places whre the code is intended to fall through. Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-04-20libata: Fix fall-through warnings for ClangGustavo A. R. Silva
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning by explicitly adding a break statement instead of letting the code fall through to the next case. Link: https://github.com/KSPP/linux/issues/115 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2021-04-20video: hyperv_fb: Add ratelimit on error messageMichael Kelley
Due to a full ring buffer, the driver may be unable to send updates to the Hyper-V host. But outputing the error message can make the problem worse because console output is also typically written to the frame buffer. As a result, in some circumstances the error message is output continuously. Break the cycle by rate limiting the error message. Also output the error code for additional diagnosability. Signed-off-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/1618933459-10585-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-04-20Drivers: hv: vmbus: Increase wait time for VMbus unloadMichael Kelley
When running in Azure, disks may be connected to a Linux VM with read/write caching enabled. If a VM panics and issues a VMbus UNLOAD request to Hyper-V, the response is delayed until all dirty data in the disk cache is flushed. In extreme cases, this flushing can take 10's of seconds, depending on the disk speed and the amount of dirty data. If kdump is configured for the VM, the current 10 second timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD complete message may arrive well after the kdump kernel is already running, causing problems. Note that no problem occurs if kdump is not enabled because Hyper-V waits for the cache flush before doing a reboot through the BIOS/UEFI code. Fix this problem by increasing the timeout in vmbus_wait_for_unload() to 100 seconds. Also output periodic messages so that if anyone is watching the serial console, they won't think the VM is completely hung. Fixes: 911e1987efc8 ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-04-20Drivers: hv: vmbus: Initialize unload_event staticallyAndrea Parri (Microsoft)
If a malicious or compromised Hyper-V sends a spurious message of type CHANNELMSG_UNLOAD_RESPONSE, the function vmbus_unload_response() will call complete() on an uninitialized event, and cause an oops. Reported-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20210420014350.2002-1-parri.andrea@gmail.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
2021-04-20Merge series "spi: altera: Add DFL bus support for Altera SPI" from ↵Mark Brown
matthew.gerlach@linux.intel.com Matthew Gerlach <matthew.gerlach@linux.intel.com>: From: Matthew Gerlach <matthew.gerlach@linux.intel.com> This patch set adds Device Feature List (DFL) bus support for the Altera SPI Master controller. Patch 1 separates spi-altera.c into spi-altera-core.c and spi-altera-platform.c. Patch 2 adds spi-altera-dfl.c. Matthew Gerlach (2): spi: altera: separate core code from platform code spi: altera: Add DFL bus driver for Altera API Controller drivers/spi/Kconfig | 18 +- drivers/spi/Makefile | 4 +- drivers/spi/spi-altera-core.c | 222 ++++++++++++++++++++++ drivers/spi/spi-altera-dfl.c | 204 ++++++++++++++++++++ drivers/spi/spi-altera-platform.c | 172 +++++++++++++++++ drivers/spi/spi-altera.c | 378 -------------------------------------- include/linux/spi/altera.h | 21 +++ 7 files changed, 639 insertions(+), 380 deletions(-) create mode 100644 drivers/spi/spi-altera-core.c create mode 100644 drivers/spi/spi-altera-dfl.c create mode 100644 drivers/spi/spi-altera-platform.c delete mode 100644 drivers/spi/spi-altera.c -- 1.8.3.1
generated by cgit (git 2.34.1) at 2025-09-13 02:46:09 +0000