| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 PASID updates from Borislav Petkov:
"Initial support for sharing virtual addresses between the CPU and
devices which doesn't need pinning of pages for DMA anymore.
Add support for the command submission to devices using new x86
instructions like ENQCMD{,S} and MOVDIR64B. In addition, add support
for process address space identifiers (PASIDs) which are referenced by
those command submission instructions along with the handling of the
PASID state on context switch as another extended state.
Work by Fenghua Yu, Ashok Raj, Yu-cheng Yu and Dave Jiang"
* tag 'x86_pasid_for_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Add an enqcmds() wrapper for the ENQCMDS instruction
x86/asm: Carve out a generic movdir64b() helper for general usage
x86/mmu: Allocate/free a PASID
x86/cpufeatures: Mark ENQCMD as disabled when configured out
mm: Add a pasid member to struct mm_struct
x86/msr-index: Define an IA32_PASID MSR
x86/fpu/xstate: Add supervisor PASID state for ENQCMD
x86/cpufeatures: Enumerate ENQCMD and ENQCMDS instructions
Documentation/x86: Add documentation for SVA (Shared Virtual Addressing)
iommu/vt-d: Change flags type to unsigned int in binding mm
drm, iommu: Change type of pasid to u32
|
|
Define a new configuration entry VFIO_PCI_ZDEV for VFIO/PCI.
When this s390-only feature is configured we add capabilities to the
VFIO_DEVICE_GET_INFO ioctl that describe features of the associated
zPCI device and its underlying hardware.
This patch is based on work previously done by Pierre Morel.
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Currently only resetting the DPRC container is supported which
will reset all the objects inside it. Resetting individual
objects is possible from the userspace by issueing commands
towards MC firmware.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The software uses a memory-mapped I/O command interface (MC portals) to
communicate with the MC hardware. This command interface is used to
discover, enumerate, configure and remove DPAA2 objects. The DPAA2
objects use MSIs, so the command interface needs to be emulated
such that the correct MSI is configured in the hardware (the guest
has the virtual MSIs).
This patch is adding read/write support for fsl-mc devices. The mc
commands are emulated by the userspace. The host is just passing
the correct command to the hardware.
Also the current patch limits userspace to write complete
64byte command once and read 64byte response by one ioctl.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This patch allows to set an eventfd for fsl-mc device interrupts
and also to trigger the interrupt eventfd from userspace for testing.
All fsl-mc device interrupts are MSIs. The MSIs are allocated from
the MSI domain only once per DPRC and used by all the DPAA2 objects.
The interrupts are managed by the DPRC in a pool of interrupts. Each
device requests interrupts from this pool. The pool is allocated
when the first virtual device is setting the interrupts.
The pool of interrupts is protected by a lock.
The DPRC has an interrupt of its own which indicates if the DPRC
contents have changed. However, currently, the contents of a DPRC
assigned to the guest cannot be changed at runtime, so this interrupt
is not configured.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
This patch adds the skeleton for interrupt support
for fsl-mc devices. The interrupts are not yet functional,
the functionality will be added by subsequent patches.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Only the DPRC object allocates interrupts from the MSI
interrupt domain. The interrupts are managed by the DPRC in
a pool of interrupts. The access to this pool of interrupts
has to be protected with a lock.
This patch extends the current lock implementation to have a
lock per DPRC.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Allow userspace to mmap device regions for direct access of
fsl-mc devices.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Expose to userspace information about the memory regions.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Allow userspace to get fsl-mc device info (number of regions
and irqs).
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The DPRC (Data Path Resource Container) device is a bus device and has
child devices attached to it. When the vfio-fsl-mc driver is probed
the DPRC is scanned and the child devices discovered and initialized.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@nxp.com>
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 platform updates from Borislav Petkov:
- Cleanup different aspects of the UV code and start adding support for
the new UV5 class of systems (Mike Travis)
- Use a flexible array for a dynamically sized struct uv_rtc_timer_head
(Gustavo A. R. Silva)
* tag 'x86_platform_for_v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/platform/uv: Update Copyrights to conform to HPE standards
x86/platform/uv: Update for UV5 NMI MMR changes
x86/platform/uv: Update UV5 TSC checking
x86/platform/uv: Update node present counting
x86/platform/uv: Update UV5 MMR references in UV GRU
x86/platform/uv: Adjust GAM MMR references affected by UV5 updates
x86/platform/uv: Update MMIOH references based on new UV5 MMRs
x86/platform/uv: Add and decode Arch Type in UVsystab
x86/platform/uv: Add UV5 direct references
x86/platform/uv: Update UV MMRs for UV5
drivers/misc/sgi-xp: Adjust references in UV kernel modules
x86/platform/uv: Remove SCIR MMR references for UV systems
x86/platform/uv: Remove UV BAU TLB Shootdown Handler
x86/uv/time: Use a flexible array in struct uv_rtc_timer_head
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RAS updates from Borislav Petkov:
- Extend the recovery from MCE in kernel space also to processes which
encounter an MCE in kernel space but while copying from user memory
by sending them a SIGBUS on return to user space and umapping the
faulty memory, by Tony Luck and Youquan Song.
- memcpy_mcsafe() rework by splitting the functionality into
copy_mc_to_user() and copy_mc_to_kernel(). This, as a result, enables
support for new hardware which can recover from a machine check
encountered during a fast string copy and makes that the default and
lets the older hardware which does not support that advance recovery,
opt in to use the old, fragile, slow variant, by Dan Williams.
- New AMD hw enablement, by Yazen Ghannam and Akshay Gupta.
- Do not use MSR-tracing accessors in #MC context and flag any fault
while accessing MCA architectural MSRs as an architectural violation
with the hope that such hw/fw misdesigns are caught early during the
hw eval phase and they don't make it into production.
- Misc fixes, improvements and cleanups, as always.
* tag 'ras_updates_for_v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Allow for copy_mc_fragile symbol checksum to be generated
x86/mce: Decode a kernel instruction to determine if it is copying from user
x86/mce: Recover from poison found while copying from user space
x86/mce: Avoid tail copy when machine check terminated a copy from user
x86/mce: Add _ASM_EXTABLE_CPY for copy user access
x86/mce: Provide method to find out the type of an exception handler
x86/mce: Pass pointer to saved pt_regs to severity calculation routines
x86/copy_mc: Introduce copy_mc_enhanced_fast_string()
x86, powerpc: Rename memcpy_mcsafe() to copy_mc_to_{user, kernel}()
x86/mce: Drop AMD-specific "DEFERRED" case from Intel severity rule list
x86/mce: Add Skylake quirk for patrol scrub reported errors
RAS/CEC: Convert to DEFINE_SHOW_ATTRIBUTE()
x86/mce: Annotate mce_rd/wrmsrl() with noinstr
x86/mce/dev-mcelog: Do not update kflags on AMD systems
x86/mce: Stop mce_reign() from re-computing severity for every CPU
x86/mce: Make mce_rdmsrl() panic on an inaccessible MSR
x86/mce: Increase maximum number of banks to 64
x86/mce: Delay clearing IA32_MCG_STATUS to the end of do_machine_check()
x86/MCE/AMD, EDAC/mce_amd: Remove struct smca_hwid.xec_bitmap
RAS/CEC: Fix cec_init() prototype
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Add Amazon's Annapurna Labs memory controller EDAC driver (Talel
Shenhar)
- New AMD CPUs support (Yazen Ghannam)
- The usual misc fixes and cleanups all over the subsystem
* tag 'edac_updates_for_v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Set proper family type for Family 19h Models 20h-2Fh
EDAC/mc_sysfs: Add missing newlines when printing {max,dimm}_location
EDAC/aspeed: Use module_platform_driver() to simplify
EDAC, sb_edac: Simplify switch statement
EDAC/ti: Fix handling of platform_get_irq() error
EDAC/aspeed: Fix handling of platform_get_irq() error
EDAC/i5100: Fix error handling order in i5100_init_one()
EDAC/highbank: Handover Calxeda Highbank maintenance to Andre Przywara
EDAC/socfpga: Transfer SoCFPGA EDAC maintainership
EDAC/thunderx: Make symbol lmc_dfs_ents static
EDAC/al-mc-edac: Add Amazon's Annapurna Labs Memory Controller driver
dt-bindings: EDAC: Add Amazon's Annapurna Labs Memory Controller binding
EDAC/mce_amd: Add new error descriptions for existing types
EDAC: Replace HTTP links with HTTPS ones
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- Conversion of the Mac IDE driver to a platform driver
- Minor cleanups and fixes
* tag 'm68k-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
ide/macide: Convert Mac IDE driver to platform driver
m68k: Replace HTTP links with HTTPS ones
m68k: mm: Remove superfluous memblock_alloc*() casts
m68k: mm: Use PAGE_ALIGNED() helper
m68k: Sort selects in main Kconfig
m68k: amiga: Clean up Amiga hardware configuration
m68k: Revive _TIF_* masks
m68k: Correct some typos in comments
m68k: Use get_kernel_nofault() in show_registers()
zorro: Fix address space collision message with RAM expansion boards
m68k: amiga: Fix Denise detection on OCS
|
|
kmalloc returns KSEG0 addresses so convert back from KSEG1
in kfree. Also make sure array is freed when the driver is
unloaded from the kernel.
Fixes: ef11291bcd5f ("Add support the Korina (IDT RC32434) Ethernet MAC")
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"There's quite a lot of code here, but much of it is due to the
addition of a new PMU driver as well as some arm64-specific selftests
which is an area where we've traditionally been lagging a bit.
In terms of exciting features, this includes support for the Memory
Tagging Extension which narrowly missed 5.9, hopefully allowing
userspace to run with use-after-free detection in production on CPUs
that support it. Work is ongoing to integrate the feature with KASAN
for 5.11.
Another change that I'm excited about (assuming they get the hardware
right) is preparing the ASID allocator for sharing the CPU page-table
with the SMMU. Those changes will also come in via Joerg with the
IOMMU pull.
We do stray outside of our usual directories in a few places, mostly
due to core changes required by MTE. Although much of this has been
Acked, there were a couple of places where we unfortunately didn't get
any review feedback.
Other than that, we ran into a handful of minor conflicts in -next,
but nothing that should post any issues.
Summary:
- Userspace support for the Memory Tagging Extension introduced by
Armv8.5. Kernel support (via KASAN) is likely to follow in 5.11.
- Selftests for MTE, Pointer Authentication and FPSIMD/SVE context
switching.
- Fix and subsequent rewrite of our Spectre mitigations, including
the addition of support for PR_SPEC_DISABLE_NOEXEC.
- Support for the Armv8.3 Pointer Authentication enhancements.
- Support for ASID pinning, which is required when sharing
page-tables with the SMMU.
- MM updates, including treating flush_tlb_fix_spurious_fault() as a
no-op.
- Perf/PMU driver updates, including addition of the ARM CMN PMU
driver and also support to handle CPU PMU IRQs as NMIs.
- Allow prefetchable PCI BARs to be exposed to userspace using normal
non-cacheable mappings.
- Implementation of ARCH_STACKWALK for unwinding.
- Improve reporting of unexpected kernel traps due to BPF JIT
failure.
- Improve robustness of user-visible HWCAP strings and their
corresponding numerical constants.
- Removal of TEXT_OFFSET.
- Removal of some unused functions, parameters and prototypes.
- Removal of MPIDR-based topology detection in favour of firmware
description.
- Cleanups to handling of SVE and FPSIMD register state in
preparation for potential future optimisation of handling across
syscalls.
- Cleanups to the SDEI driver in preparation for support in KVM.
- Miscellaneous cleanups and refactoring work"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (148 commits)
Revert "arm64: initialize per-cpu offsets earlier"
arm64: random: Remove no longer needed prototypes
arm64: initialize per-cpu offsets earlier
kselftest/arm64: Check mte tagged user address in kernel
kselftest/arm64: Verify KSM page merge for MTE pages
kselftest/arm64: Verify all different mmap MTE options
kselftest/arm64: Check forked child mte memory accessibility
kselftest/arm64: Verify mte tag inclusion via prctl
kselftest/arm64: Add utilities and a test to validate mte memory
perf: arm-cmn: Fix conversion specifiers for node type
perf: arm-cmn: Fix unsigned comparison to less than zero
arm64: dbm: Invalidate local TLB when setting TCR_EL1.HD
arm64: mm: Make flush_tlb_fix_spurious_fault() a no-op
arm64: Add support for PR_SPEC_DISABLE_NOEXEC prctl() option
arm64: Pull in task_stack_page() to Spectre-v4 mitigation code
KVM: arm64: Allow patching EL2 vectors even with KASLR is not enabled
arm64: Get rid of arm64_ssbd_state
KVM: arm64: Convert ARCH_WORKAROUND_2 to arm64_get_spectre_v4_state()
KVM: arm64: Get rid of kvm_arm_have_ssbd()
KVM: arm64: Simplify handling of ARCH_WORKAROUND_2
...
|
|
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa86 ("net: dsa: microchip: add MIB counter reading support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd
Pull tpm updates from Jarkko Sakkinen:
"Support for a new TPM device and fixes and Git URL change (infraded ->
korg)"
* tag 'tpmdd-next-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
MAINTAINERS: TPM DEVICE DRIVER: Update GIT
tpm_tis: Add a check for invalid status
tpm: use %*ph to print small buffer
dt-bindings: Add SynQucer TPM MMIO as a trivial device
tpm: tis: add support for MMIO TPM on SynQuacer
|
|
Use netdev_err for better device identification in syslog.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the router is rebooted without a power cycle, the USB device
remains connected but its configuration is reset. This results in
a non-working ethernet connection with messages like this in syslog:
usb 2-2: RX packet too long: 65535 B
Re-enable ethernet mode when receiving a packet with invalid size of
0xffff.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
These fixes missed the v5.9 merge window, pick them up for early v5.10 merge.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
|
|
Fix following warning:
drivers/cpufreq/cpufreq_stats.c:63:10: warning: %d in format string (no.
1) requires 'int' but the argument type is 'unsigned int'
Fixes: 40c3bd4cfa6f ("cpufreq: stats: Defer stats update to cpufreq_stats_record_transition()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
thermal_genl_sampling_temp() misses to call nlmsg_free() in an error path.
Jump to out_free to fix it.
Fixes: 1ce50e7d408ef2 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200929082652.59876-1-jingxiangfeng@huawei.com
|
|
The bandgap sensor can be idled when the processor is too, but it
isn't currently being done, so the power consumption of OMAP3
boards can elevated if the bangap sensor is enabled.
This patch attempts to use some additional power management
to idle the clock to the bandgap when not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200911123157.759379-1-aford173@gmail.com
|
|
This patch add thermal sensor controller support for A100,
which is similar to the previous ones.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/48cc75920b5c69027134626157089d8b94942711.1595572867.git.frank@allwinnertech.com
|
|
sun50i_h6_ths_calibrate
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
|
|
1. devfreq_cooling.c: The variable *tz is not used in
devfreq_cooling_get_requested_power(), devfreq_cooling_state2power()
and devfreq_cooling_power2state().
2. cpufreq_cooling.c: After 84fe2cab48590, the variable *tz is not used
anymore in cpufreq_get_requested_power(), cpufreq_state2power() and
cpufreq_power2state().
Remove the variable *tz.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200914071101.13575-1-zhuguangqing83@gmail.com
|
|
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
|
|
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
|
|
The mutex poweroff_lock is initialized statically. It is
unnecessary to initialize by mutex_init().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200916062139.191233-1-miaoqinglang@huawei.com
|
|
The comment of idle_duration_us and the name of latency_ns can be misleading,
so fix them.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200917073553.898-1-zhuguangqing83@gmail.com
|
|
The rcar_gen3_thermal driver also supports RZ/G2 SoC's, update the
description to reflect this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Chris Paterson <Chris.Paterson2@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200917152141.30070-1-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
Simplify the return expression.
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200921131107.93273-1-miaoqinglang@huawei.com
|
|
According to Documentation/process/coding-style.rst, if one branch of a
conditional statement needs braces, both branches should use braces.
Fixes: bbcf90c0646ac797 ("thermal: Explicitly enable non-changing thermal zone devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200819092716.3191-1-geert+renesas@glider.be
|
|
Use kobj_to_dev() instead of container_of()
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597799671-11530-1-git-send-email-tiantao6@hisilicon.com
|
|
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-2-git-send-email-Anson.Huang@nxp.com
|
|
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-1-git-send-email-Anson.Huang@nxp.com
|
|
There is a spelling mistake in the Kconfig text, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200810082739.48007-1-colin.king@canonical.com
|
|
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-next
amd-drm-fixes-5.10-2020-10-09:
amdgpu:
- Clean up indirect register access
- Navy Flounder fixes
- SMU11 AC/DC interrupt fixes
- GPUVM alignment fix
- Display fixes
- Misc other fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201009222810.4030-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
Propagated from drm-intel-next-queued:
- Fix CRTC state checker (Ville)
Propated from drm-intel-gt-next:
- Avoid implicit vmpa for highmem on 32b (Chris)
- Prevent PAT attriutes for writecombine if CPU doesn't support PAT (Chris)
- Clear the buffer pool age before use. (Chris)
- Fix error code (Dan)
- Break up error capture compression loops (Chris)
- Fix uninitialized variable in context_create_request (Maarten)
- Check for errors on i915_vm_alloc_pt_stash to avoid NULL dereference (Matt)
- Serialize debugfs i915_gem_objects with ctx->mutex (Chris)
- Fix a rebase mistake caused during drm-intel-gt-next creation (Chris)
- Hold request reference for canceling an active context (Chris)
- Heartbeats fixes (Chris)
- Use usigned during batch copies (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201002182610.GA2204465@intel.com
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next
HyperBus changes
* DMA support for TI's AM654 HyperBus controller driver.
* HyperBus frontend driver for Renesas RPC-IF driver.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- Support for Winbond w25q64jwm flash
- Enable 4K sector support for mx25l12805d
SPI NOR controller drivers changes:
- intel-spi:
- Add Alder Lake-S PCI ID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
NAND core changes:
* Use the new generic ECC object
* Create helpers to set/extract the ECC requirements
* Create a helper to extract the ECC configuration
* Add a NAND page I/O request type
* Introduce the ECC engine framework
Raw NAND core changes:
* Don't overwrite the error code from nand_set_ecc_soft_ops()
* Introduce nand_set_ecc_on_host_ops()
* Use the NAND framework user_conf object for ECC flags
* Use the ECC framework user input parsing bits
* Use the ECC framework nand_ecc_is_strong_enough() helper
* Use the ECC framework OOB layouts
* Make use of the ECC framework
* Use nanddev_get/set_ecc_requirements() when relevant
* Use the new ECC engine type enumeration
* Separate the ECC engine type and the ECC byte placement
* Move the nand_ecc_algo enum to the generic NAND layer
* Rename the ECC algorithm enumeration items
* Add a kernel doc to the ECC algorithm enumeration
* DT bindings:
- Document boolean NAND ECC properties
- Document nand-ecc-engine
- Document nand-ecc-placement
Raw NAND drivers changes:
* Ams-Delta: Fix non-OF build warning
* Atmel:
- Check return values for nand_read_data_op
- Simplify with dev_err_probe()
- Get rid of the legacy interface implementation
- Convert the driver to exec_op()
- Use nand_prog_page_end_op()
- Use nand_{write,read}_data_op()
- Drop redundant nand_read_page_op()
- Enable the NFC controller at probe time
- Disable clk on error handling path in probe
* Cadence: remove a redundant dev_err call
* Gpmi:
- Simplify with dev_err_probe()
* Marvell:
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Fix and update kerneldoc
- Simplify with dev_err_probe()
- Support panic_write for mtdoops
* Onenand:
- Simplify the return expression of onenand_transfer_auto_oob
- Simplify with dev_err_probe()
* Oxnas: cleanup/simplify code
* Pasemi: Make pasemi_device_ready() static
* Qcom: Simplify with dev_err_probe()
* Stm32_fmc2: fix a buffer overflow
* Vf610: Remove unused function vf610_nfc_transfer_size()
SPI-NAND changes:
* Use nanddev_get_ecc_conf() when relevant
* Gigadevice:
- Add support for GD5F4GQ4xC
- Add QE Bit
- Use only one dummy byte in QUADIO
* Macronix:
- Add support for MX31UF1GE4BC
- Add support for MX31LF1GE4BC
|
|
The VCAP_IS1_ACT_VID_REPLACE_ENA action, from the VCAP IS1 ingress TCAM,
changes the classified VLAN.
We are only exposing this ability for switch ports that are under VLAN
aware bridges. This is because in standalone ports mode and under a
bridge with vlan_filtering=0, the ocelot driver configures the switch to
operate as VLAN-unaware, so the classified VLAN is not derived from the
802.1Q header from the packet, but instead is always equal to the
port-based VLAN ID of the ingress port. We _can_ still change the
classified VLAN for packets when operating in this mode, but the end
result will most likely be a drop, since both the ingress and the egress
port need to be members of the modified VLAN. And even if we install the
new classified VLAN into the VLAN table of the switch, the result would
still not be as expected: we wouldn't see, on the output port, the
modified VLAN tag, but the original one, even though the classified VLAN
was indeed modified. This is because of how the hardware works: on
egress, what is pushed to the frame is a "port tag", which gives us the
following options:
- Tag all frames with port tag (derived from the classified VLAN)
- Tag all frames with port tag, except if the classified VLAN is 0 or
equal to the native VLAN of the egress port
- No port tag
Needless to say, in VLAN-unaware mode we are disabling the port tag.
Otherwise, the existing VLAN tag would be ignored, and a second VLAN
tag (the port tag), holding the classified VLAN, would be pushed
(instead of replacing the existing 802.1Q tag). This is definitely not
what the user wanted when installing a "vlan modify" action.
So it is simply not worth bothering with VLAN modify rules under other
configurations except when the ports are fully VLAN-aware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a methodical transition of the driver from phylib
to phylink, following the guidelines from sfp-phylink.rst.
The MAC register configurations based on interface mode
were moved from the probing path to the mac_config() hook.
MAC enable and disable commands (enabling Rx and Tx paths
at MAC level) were also extracted and assigned to their
corresponding phylink hooks.
As part of the migration to phylink, the serdes configuration
from the driver was offloaded to the PCS_LYNX module,
introduced in commit 0da4c3d393e4 ("net: phy: add Lynx PCS module"),
the PCS_LYNX module being a mandatory component required to
make the enetc driver work with phylink.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.cionei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Decouple internal mdio bus creation from serdes
configuration, as a prerequisite to offloading
serdes configuration to a different module.
Group together mdio bus creation routines, cleanup.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
