| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- partition parser: Support MTD names containing one or more colons.
- mtdblock: clear cache_state to avoid writing to bad blocks
repeatedly.
Raw NAND core changes:
- Stop using nand_release(), patched all drivers.
- Give more information about the ECC weakness when not matching the
chip's requirement.
- MAINTAINERS updates.
- Support emulated SLC mode on MLC NANDs.
- Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
- Take check_only into account.
- Add an invalid ECC mode to discriminate with valid ones.
- Return an enum from of_get_nand_ecc_algo().
- Drop OOB_FIRST placement scheme.
- Introduce nand_extract_bits().
- Ensure a consistent bitflips numbering.
- BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
- Fix nand_gpio_waitrdy().
- Propage CS selection to sub operations.
- Add a NAND_NO_BBM_QUIRK flag.
- Give the possibility to verify a read operation is supported.
- Add a helper to check supported operations.
- Avoid indirect access to ->data_buf().
- Rename the use_bufpoi variables.
- Fix comments about the use of bufpoi.
- Rename a NAND chip option.
- Reorder the nand_chip->options flags.
- Translate obscure bitfields into readable macros.
- Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
- Fixed many error paths.
- Arasan
- New driver
- Au1550nd:
- Various cleanups
- Migration to ->exec_op()
- brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
- Cadence
- Make cadence_nand_attach_chip static.
- Cafe:
- Set the NAND_NO_BBM_QUIRK flag
- cmx270:
- Remove this controller driver.
- cs553x:
- Misc cleanup
- Migration to ->exec_op()
- Davinci:
- Misc cleanup.
- Migration to ->exec_op()
- Denali:
- Add more delays before latching incoming data
- Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
- Fsmc:
- Change to non-atomic bit operations.
- GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
- Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
- Marvell:
- Misc cleanup and small fixes
- Nandsim:
- Fix the error paths, driver wide.
- Omap_elm:
- Fix runtime PM imbalance.
- STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
SPI NOR core changes:
- Add, update support and fix few flashes.
- Prepare BFPT parsing for JESD216 rev D.
- Kernel doc fixes.
CFI changes:
- Support the absence of protection registers for Intel CFI flashes.
- Replace zero-length array with flexible-arrays"
* tag 'mtd/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (208 commits)
mtd: clear cache_state to avoid writing to bad blocks repeatedly
mtd: parser: cmdline: Support MTD names containing one or more colons
mtd: physmap_of_gemini: remove defined but not used symbol 'syscon_match'
mtd: rawnand: Add an invalid ECC mode to discriminate with valid ones
mtd: rawnand: Return an enum from of_get_nand_ecc_algo()
mtd: rawnand: Drop OOB_FIRST placement scheme
mtd: rawnand: Avoid a typedef
mtd: Fix typo in mtd_ooblayout_set_databytes() description
mtd: rawnand: Stop using nand_release()
mtd: rawnand: nandsim: Reorganize ns_cleanup_module()
mtd: rawnand: nandsim: Rename a label in ns_init_module()
mtd: rawnand: nandsim: Manage lists on error in ns_init_module()
mtd: rawnand: nandsim: Fix the label pointing on nand_cleanup()
mtd: rawnand: nandsim: Free erase_block_wear on error
mtd: rawnand: nandsim: Use an additional label when freeing the nandsim object
mtd: rawnand: nandsim: Stop using nand_release()
mtd: rawnand: nandsim: Free the partition names in ns_free()
mtd: rawnand: nandsim: Free the allocated device on error in ns_init()
mtd: rawnand: nandsim: Free partition names on error in ns_init()
mtd: rawnand: nandsim: Fix the two ns_alloc_device() error paths
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time around we have four lines of diff in the core framework,
removing a function that isn't used anymore. Otherwise the main new
thing for the common clk framework is that it is selectable in the
Kconfig language now. Hopefully this will let clk drivers and clk
consumers be testable on more than the architectures that support the
clk framework. The goal is to introduce some Kunit tests for the
framework.
Outside of the core framework we have the usual set of various driver
updates and non-critical fixes. The dirstat shows that the new
Baikal-T1 driver is the largest addition this time around in terms of
lines of code. After that the x86 (Intel), Qualcomm, and Mediatek
drivers introduce many lines to support new or upcoming SoCs. After
that the dirstat shows the usual suspects working on their SoC support
by fixing minor bugs, correcting data and converting some of their DT
bindings to YAML.
Core:
- Allow the COMMON_CLK config to be selectable
New Drivers:
- Clk driver for Baikal-T1 SoCs
- Mediatek MT6765 clock support
- Support for Intel Agilex clks
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for the new Renesas RZ/G1H (R8A7742) SoC
- Add support for Qualcomm's MSM8939 Generic Clock Controller
Updates:
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- A single minor rounding fix for the legacy Allwinner clock support
- A few patches from Abel Vesa as preparation of adding audiomix
clock support on i.MX
- A couple of cleanups from Anson Huang for i.MX clk-sscg-pll and
clk-pllv3 drivers
- Drop dependency on ARM64 for i.MX8M clock driver, to support
aarch32 mode on aarch64 hardware
- A series from Peng Fan to improve i.MX8M clock drivers, using
composite clock for core and bus clk slice
- Set a better parent clock for flexcan on i.MX6UL to support CiA102
defined bit rates
- A couple changes for EMC frequency scaling on Tegra210
- Support for CPU frequency scaling on Tegra20/Tegra30
- New clk gate for CSI test pattern generator on Tegra210
- Regression fixes for Samsung exynos542x and exynos5433 SoCs
- Use of fallthrough; attribute for Samsung s3c24xx
- Updates and fixup HDMI and video clocks on Meson8b
- Fixup reset polarity on Meson8b
- Fix GPU glitch free mux switch on Meson gx and g12
- A minor fix for the currently unused suspend/resume handling on
Renesas RZ/A1 and RZ/A2
- Two more conversions of Renesas DT bindings to json-schema
- Add support for the USB 2.0 clock selector on Renesas R-Car M3-W+"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (155 commits)
clk: mediatek: Remove ifr{0,1}_cfg_regs structures
clk: baikal-t1: remove redundant assignment to variable 'divider'
clk: baikal-t1: fix spelling mistake "Uncompatible" -> "Incompatible"
dt-bindings: clock: Add a missing include to MMP Audio Clock binding
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
clk: clk-si5341: Add support for the Si5345 series
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"This time there are lots of changes. Quite a few changes to the core,
lots of driver changes and one change to kobject core (with Ack from
Greg).
Summary:
kobject:
- Increase number of allowed uevent variables
power-supply core:
- Add power-supply type in uevent
- Cleanup property handling in core
- Make property and usb_type pointers const
- Convert core power-supply DT binding to YAML
- Cleanup HWMON code
- Add new health status "calibration required"
- Add new properties for manufacture date and capacity error margin
battery drivers:
- new cw2015 battery driver used by pine64 Pinebook Pro laptop
- axp22: blacklist on Meegopad T02
- sc27xx: support current/voltage reading
- max17042: support time-to-empty reading
- simple-battery: add more battery parameters
- bq27xxx: convert DT binding document to YAML
- sbs-battery: add TI BQ20Z65 support, fix technology property,
convert DT binding to YAML, add option to disable charger
broadcasts, add new properties: manufacture date, capacity
error margin, average current, charge current and voltage and
support calibration required health status
- misc fixes
charger drivers:
- bq25890: cleanup, implement charge type, precharge current and
input current limiting properties
- bd70528: use new linear range helper library
- bd99954: new charger driver
- mp2629: new charger driver
- misc fixes
reboot drivers:
- oxnas-restart: introduce new driver
- syscon-reboot: convert DT binding to YAML, add parent syscon device
support
- misc fixes"
* tag 'for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (85 commits)
power: supply: cw2015: Attach OF ID table to the driver
power: reset: gpio-poweroff: add missing '\n' in dev_err()
Revert "power: supply: sbs-battery: simplify read_read_string_data"
Revert "power: supply: sbs-battery: add PEC support"
dt-bindings: power: sbs-battery: Convert to yaml
power: supply: sbs-battery: constify power-supply property array
power: supply: sbs-battery: switch to i2c's probe_new
power: supply: sbs-battery: switch from of_property_* to device_property_*
power: supply: sbs-battery: add ability to disable charger broadcasts
power: supply: sbs-battery: fix idle battery status
power: supply: sbs-battery: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED support
power: supply: sbs-battery: add MANUFACTURE_DATE support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT/VOLTAGE_MAX support
power: supply: sbs-battery: Improve POWER_SUPPLY_PROP_TECHNOLOGY support
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CURRENT_AVG support
power: supply: sbs-battery: add PEC support
power: supply: sbs-battery: simplify read_read_string_data
power: supply: sbs-battery: add POWER_SUPPLY_PROP_CAPACITY_ERROR_MARGIN support
power: supply: sbs-battery: Add TI BQ20Z65 support
power: supply: core: add POWER_SUPPLY_HEALTH_CALIBRATION_REQUIRED
...
|
|
No user pointers for sysctls anymore.
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Reported-by: build test robot <lkp@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull dmaengine updates from Vinod Koul:
"A fairly small dmaengine update which includes mostly driver updates
(dmatest, dw-edma, ioat, mmp-tdma and k3-udma) along with Renesas
binding update to json-schema"
* tag 'dmaengine-5.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (39 commits)
dmaengine: imx-sdma: initialize all script addresses
dmaengine: ti: k3-udma: Use proper return code in alloc_chan_resources
dmaengine: ti: k3-udma: Remove udma_chan.in_ring_cnt
dmaengine: ti: k3-udma: Add missing dma_sync call for rx flush descriptor
dmaengine: at_xdmac: Replace zero-length array with flexible-array
dmaengine: at_hdmac: Replace zero-length array with flexible-array
dmaengine: qcom: bam_dma: Replace zero-length array with flexible-array
dmaengine: ti: k3-udma: Use PTR_ERR_OR_ZERO() to simplify code
dmaengine: moxart-dma: Drop pointless static qualifier in moxart_probe()
dmaengine: sf-pdma: Simplify the error handling path in 'sf_pdma_probe()'
dmaengine: qcom_hidma: use true,false for bool variable
dmaengine: dw-edma: support local dma device transfer semantics
dmaengine: Fix doc strings to satisfy validation script
dmaengine: Include dmaengine.h into dmaengine.c
dmaengine: dmatest: Describe members of struct dmatest_info
dmaengine: dmatest: Describe members of struct dmatest_params
dmaengine: dmatest: Allow negative timeout value to specify infinite wait
Revert "dmaengine: dmatest: timeout value of -1 should specify infinite wait"
dmaengine: stm32-dma: direct mode support through device tree
dt-bindings: dma: add direct mode support through device tree in stm32-dma
...
|
|
Move all files related to the Intel IOMMU driver into its own
subdirectory.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20200609130303.26974-3-joro@8bytes.org
|
|
Move all files related to the AMD IOMMU driver into its own
subdirectory.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Reviewed-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20200609130303.26974-2-joro@8bytes.org
|
|
The word 'descriptor' is misspelled throughout the tree.
Fix it up accordingly:
decriptors -> descriptors
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609124610.3445662-9-kieran.bingham+renesas@ideasonboard.com
|
|
* acpica:
ACPICA: Update version to 20200528
ACPICA: iASL: add new OperationRegion subtype keyword PlatformRtMechanism
ACPICA: acpidump: Removed dead code from oslinuxtbl.c
|
|
* pm-cpufreq:
cpufreq: CPPC: add SW BOOST support
cpufreq: change '.set_boost' to act on one policy
cpufreq: tegra186: add CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
* pm-acpi:
ACPI: PM: Avoid using power resources if there are none for D0
|
|
* pm-opp:
opp: Don't parse icc paths unnecessarily
opp: Remove bandwidth votes when target_freq is zero
opp: core: add regulators enable and disable
opp: Reorder the code for !target_freq case
opp: Expose bandwidth information via debugfs
cpufreq: dt: Add support for interconnect bandwidth scaling
opp: Update the bandwidth on OPP frequency changes
opp: Add sanity checks in _read_opp_key()
opp: Add support for parsing interconnect bandwidth
interconnect: Remove unused module exit code from core
interconnect: Disallow interconnect core to be built as a module
interconnect: Add of_icc_get_by_index() helper function
OPP: Add helpers for reading the binding properties
dt-bindings: opp: Introduce opp-peak-kBps and opp-avg-kBps bindings
|
|
'ret' is known to be 0 at this point. Explicitly return -ENOMEM if one of
the 'ecardm_iomap()' calls fail.
Link: https://lore.kernel.org/r/20200530081622.577888-1-christophe.jaillet@wanadoo.fr
Fixes: e95a1b656a98 ("[ARM] rpc: acornscsi: update to new style ecard driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The HACT_ACT field only needs to be written to when using a DSI display.
Let's move that setup to our DSI branch to clear a bit the common path.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/7a93436f97666a2aa025686ef3ff3606de4bec67.1590594512.git-series.maxime@cerno.tech
|
|
The hvs_latency_pix variable doesn't need to be a variable and can just be
defined.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/8535c679f79af8abaa1b7796261bfeda11f874fd.1590594512.git-series.maxime@cerno.tech
|
|
We'll need to access the crtc_state from outside of vc4_crtc.c, so let's
move it to vc4_drv.h
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/1e6e563f9c75961e2885c9d648a3130d3b46b6d1.1590594512.git-series.maxime@cerno.tech
|
|
of_device_get_match_data allow to simplify a bit the retrieval of the data
associated to the pixelvalve compatible. Let's use it.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/1ff06413a1350d28bc3e88b034ed7ad23834e5bd.1590594512.git-series.maxime@cerno.tech
|
|
Since we're going to introduce pixelvalve data structures for other SoCs
than the BCM2835, let's rename the structures defined in the code to
make it obvious which SoC we're targeting.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/39aed7dd512ce2a4560902974ec26b16b88ec68b.1590594512.git-series.maxime@cerno.tech
|
|
So far the plane creation was done when each CRTC was bound, and those
planes were only tied to the CRTC that was registering them.
This causes two main issues:
- The planes in the vc4 hardware are actually not tied to any CRTC, but
can be used with every combination
- More importantly, so far, we allocate 10 planes per CRTC, with 3 CRTCs.
However, the next generation of hardware will have 5 CRTCs, putting us
well above the maximum of 32 planes currently allowed by DRM.
This patch is the first one in a series of patches that will take down both
of these issues so that we can support the next generation of hardware
while keeping a good amount of planes.
We start by changing the way the planes are registered to first registering
the primary planes for each CRTC in the CRTC bind function as we used to,
but moving the overlay and cursor creation to the main driver bind
function, after all the CRTCs have been bound, and make the planes
associated to all CRTCs.
This will slightly change the ID order of the planes, since the primary
planes of all CRTCs will be first, and then a pattern of 8 overlays, 1
cursor plane for each CRTC.
This shouldn't cause any trouble since the ordering between the planes is
preserved though.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/0b85a3fdb20bb4ff85fb62cabd082d5a65e2730b.1590594512.git-series.maxime@cerno.tech
|
|
The planes so far were created as part of the CRTC binding code with
each planes created associated only to one CRTC. However, the hardware
in the vc4 doesn't really have such constraint and can be used with any
CRTC.
In order to rework this, let's first move the overlay and cursor planes
creation to a function of its own.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/a378ea56214179f1f25fcd36ecc69511edd1e790.1590594512.git-series.maxime@cerno.tech
|
|
vc4_drv.h doesn't have any include guards which prevents it from being
included twice. Let's add them.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/68e89e315c4c35b313efc277c9642eca684e0ade.1590594512.git-series.maxime@cerno.tech
|
|
The udl driver contains an implementation of GEM vmap and mmap
operations that is identical to the common SHMEM helper; except
that udl's code uses cached pages by default.
Convert udl to regular SHMEM helper functions. There's no reason
to have udl behave differently from all other SHMEM drivers. The
udl driver uses the SHMEM helper to enable caching.
v3:
* rebased onto Daniel's shmem untangle series
v2:
* implement .gem_create_object with SHMEM helper
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609090820.20256-3-tzimmermann@suse.de
|
|
The helper drm_gem_shmem_create_object_cached() allocates an GEM SHMEM
object and sets the map_cached flag. Useful for drivers that want cached
mappings.
v3:
* style fixes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200609090820.20256-2-tzimmermann@suse.de
|
|
m divider in DDC clock register is 4 bits wide. Fix that.
Fixes: 9c5681011a0c ("drm/sun4i: Add HDMI support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200413095457.1176754-1-jernej.skrabec@siol.net
|
|
The .gem_print_info callback in struct drm_driver is obsolete and has
no users left. Remove it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Suggested-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-44-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-43-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-42-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-41-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-40-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-39-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-38-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-37-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-36-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in
struct drm_driver to their defaults. No functional changes are
made.
v2:
* update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-35-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-34-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-33-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-32-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in
struct drm_driver to their defaults. No functional changes are
made.
v2:
* update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-31-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-30-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-29-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-28-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in
struct drm_driver to their defaults. No functional changes are
made.
v2:
* update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-27-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-26-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-25-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-24-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in
struct drm_driver to their defaults. No functional changes are
made.
v2:
* update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-23-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-22-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE sets the functions in
struct drm_driver to their defaults. No functional changes are
made.
v2:
* update for DRM_GEM_CMA_DRIVER_OPS_WITH_DUMB_CREATE
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-21-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-20-tzimmermann@suse.de
|
|
DRM_GEM_CMA_DRIVER_OPS sets the functions in struct drm_driver
to their defaults. No functional changes are made.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-19-tzimmermann@suse.de
|
|
Create GEM objects with drm_gem_cma_create_object_default_funcs(), which
allocates the object and sets CMA's default object functions. Corresponding
callbacks in struct drm_driver are cleared. No functional changes are made.
Driver and object-function instances use the same callback functions, with
the exception of vunmap. The implementation of vunmap is empty and left out
in CMA's default object functions.
v3:
* convert to DRIVER_OPS macro in a separate patch
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200605073247.4057-18-tzimmermann@suse.de
|
