| Age | Commit message (Collapse) | Author |
|---|
|
Newer firmware for the E810 devices support a 'low latency' interface to
interact with the PHY without using the Admin Queue. This is interacted
with via the REG_LL_PROXY_L and REG_LL_PROXY_H registers.
Currently, this interface is only used for Tx timestamps. There are two
different mechanisms, including one which uses an interrupt for firmware to
signal completion. However, these two methods are mutually exclusive, so no
synchronization between them was necessary.
This low latency interface is being extended in future firmware to support
also programming the PHY timers. Use of the interface for PHY timers will
need synchronization to ensure there is no overlap with a Tx timestamp.
The interrupt-based response complicates the locking somewhat. We can't use
a simple spinlock. This would require being acquired in
ice_ptp_req_tx_single_tstamp, and released in
ice_ptp_complete_tx_single_tstamp. The ice_ptp_req_tx_single_tstamp
function is called from the threaded IRQ, and the
ice_ptp_complete_tx_single_stamp is called from the low latency IRQ, so we
would need to acquire the lock with IRQs disabled.
To handle this, we'll use a wait queue along with
wait_event_interruptible_locked_irq in the update flows which don't use the
interrupt.
The interrupt flow will acquire the wait queue lock, set the
ATQBAL_FLAGS_INTR_IN_PROGRESS, and then initiate the firmware low latency
request, and unlock the wait queue lock.
Upon receipt of the low latency interrupt, the lock will be acquired, the
ATQBAL_FLAGS_INTR_IN_PROGRESS bit will be cleared, and the firmware
response will be captured, and wake_up_locked() will be called on the wait
queue.
The other flows will use wait_event_interruptible_locked_irq() to wait
until the ATQBAL_FLAGS_INTR_IN_PROGRESS is clear. This function checks the
condition under lock, but does not hold the lock while waiting. On return,
the lock is held, and a return of zero indicates we hold the lock and the
in-progress flag is not set.
This will ensure that threads which need to use the low latency interface
will sleep until they can acquire the lock without any pending low latency
interrupt flow interfering.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The TS_LL_READ macros are used as part of the low latency Tx timestamp
interface. A future firmware extension will add support for performing PHY
timer updates over this interface. Using TS_LL_READ as the prefix for these
macros will be confusing once the interface is used for other purposes.
Rename the macros, using the prefix REG_LL_PROXY_H, to better clarify that
this is for the low latency interface.
Additionally add macros for PF_SB_ATQBAH and PF_SB_ATQBAL registers to
better clarify content of this registers as PF_SB_ATQBAH contain low
part of Tx timestamp
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_read_phy_tstamp_ll_e810 function repeatedly reads the PF_SB_ATQBAL
register until the TS_LL_READ_TS bit is cleared. This is a perfect
candidate for using rd32_poll_timeout. However, the default implementation
uses a sleep-based wait. Use read_poll_timeout_atomic macro which is based
on the non-sleeping implementation and use it to replace the loop reading
in the ice_read_phy_tstamp_ll_e810 function.
Co-developed-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anton Nadezhdin <anton.nadezhdin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use string choice helpers for better readability.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202410121553.SRNFzc2M-lkp@intel.com/
Signed-off-by: R Sundar <prosunofficial@gmail.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Firmware generates events for global events or port specific events.
Driver shall subscribe for health status events from firmware on supported
FW versions >= 1.7.6.
Driver shall expose those under specific health reporter, two new
reporters are introduced:
- FW health reporter shall represent global events (problems with the
image, recovery mode);
- Port health reporter shall represent port-specific events (module
failure).
Firmware only reports problems when those are detected, it does not store
active fault list.
Driver will hold only last global and last port-specific event.
Driver will report all events via devlink health report,
so in case of multiple events of the same source they can be reviewed
using devlink autodump feature.
$ devlink health
pci/0000:b1:00.3:
reporter fw
state healthy error 0 recover 0 auto_dump true
reporter port
state error error 1 recover 0 last_dump_date 2024-03-17
last_dump_time 09:29:29 auto_dump true
$ devlink health diagnose pci/0000:b1:00.3 reporter port
Syndrome: 262
Description: Module is not present.
Possible Solution: Check that the module is inserted correctly.
Port Number: 0
Tested on Intel Corporation Ethernet Controller E810-C for SFP
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Sharon Haroni <sharon.haroni@intel.com>
Signed-off-by: Sharon Haroni <sharon.haroni@intel.com>
Co-developed-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Konrad Knitter <konrad.knitter@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The new recipe should be added even if exactly the same recipe already
exists with different priority.
Example use case is when the rule is being added from TC tool context.
It should has the highest priority, but if the recipe already exists
the rule will inherit it priority. It can lead to the situation when
the rule added from TC tool has lower priority than expected.
The solution is to check the recipe priority when trying to find
existing one.
Previous recipe is still useful. Example:
RID 8 -> priority 4
RID 10 -> priority 7
The difference is only in priority rest is let's say eth + mac +
direction.
Adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
After that IP + MAC_B + RX on RID 10 (from TC tool), forward to PF0
Both will work.
In case of adding ARP + MAC_A + RX on RID 8, forward to VF0_VSI
ARP + MAC_A + RX on RID 10, forward to PF0.
Only second one will match, but this is expected.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move ice_adapter initialization to be after HW init, so it could use HW
capabilities, like number of PFs. This is needed for devlink-resource
based RSS LUT size management for PF/VF (not in this series).
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Clean up goto labels after previous commit, to conform to single naming
scheme in ice_probe() and ice_init_dev().
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Split ice_init_hw() call out from ice_init_dev(). Such move enables
pulling the former to be even earlier on call path, what would enable
moving ice_adapter init to be between the two (in subsequent commit).
Such move enables ice_adapter to know about number of PFs.
Do the same for ice_deinit_hw(), so the init and deinit calls could
be easily mirrored.
Next commit will rename unrelated goto labels to unroll prefix.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move call to ice_wait_for_fw() from ice_init_dev() into ice_init_hw(),
where it fits better. This requires also to move ice_wait_for_fw()
to ice_common.c.
ice_is_pf_c827() is now used only in ice_common.c, so it could be static.
CC: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove hard-coded strings by using the str_off_on() helper.
Signed-off-by: Thorsten Blum <thorsten.blum@linux.dev>
Link: https://lore.kernel.org/r/20241202154603.1193-2-thorsten.blum@linux.dev
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114192701.912430-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Fix E825 initialization
Grzegorz Nitka says:
E825 products have incorrect initialization procedure, which may lead to
initialization failures and register values.
Fix E825 products initialization by adding correct sync delay, checking
the PHY revision only for current PHY and adding proper destination
device when reading port/quad.
In addition, E825 uses PF ID for indexing per PF registers and as
a primary PHY lane number, which is incorrect.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Add correct PHY lane assignment
ice: Fix ETH56G FC-FEC Rx offset value
ice: Fix quad registers read on E825
ice: Fix E825 initialization
====================
Link: https://patch.msgid.link/20250113182840.3564250-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a typo in a phydev_err message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250113091555.23594-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, an interface is created in the driver during channel assignment.
If mac80211 attempts to set a key for an interface before this assignment,
the driver caches the key. Once the interface is created, the driver
installs the cached key to the hardware. This sequence is exemplified in
mesh mode operation where the group key is set before channel assignment.
However, in ath12k_mac_update_key_cache(), after caching the key, due to
incorrect logic, it is deleted from the cache during the subsequent loop
iteration. As a result, after the interface is created, the driver does not
find any cached key, and the key is not installed to the hardware which is
wrong. This leads to issue in mesh, where broadcast traffic is not
encrypted over the air.
Fix this issue by adjusting the logic of ath12k_mac_update_key_cache()
properly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3-03253.1-QCAHKSWPL_SILICONZ-29 # Nicolas Escande <nico.escande@gmail.com>
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 # Nicolas Escande <nico.escande@gmail.com>
Fixes: 25e18b9d6b4b ("wifi: ath12k: modify ath12k_mac_op_set_key() for MLO")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Tested-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://patch.msgid.link/20250112-fix_key_cache_handling-v2-1-70e142c6153e@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
function
Currently, the uninitialized variable 'ab' is accessed in the
ath12k_mac_allocate() function. Initialize 'ab' with the first radio device
present in the hardware abstraction handle (ah). Additionally, move the
default setting procedure from the pdev mapping iteration to the total
radio calculating iteration for better code readability. Perform the
maximum radio validation check for total_radio to ensure that both num_hw
and radio_per_hw are validated indirectly, as these variables are derived
from total_radio. This also fixes the below Smatch static checker warning.
Smatch warning:
ath12k_mac_allocate() error: uninitialized symbol 'ab'
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the ath12k_get_num_hw() helper function takes the device handle
as an argument. Here, the number of hardware is retrieved from the group
handle. Demanding the device handle from the caller is unnecessary since
in some cases the group handle is already available. Additionally, there
is no longer a need for multiple indirections to get the number of
hardware. Therefore, remove this helper function and directly use
ag->num_hw. This change also fixes the below Smatch static checker
warning.
Smatch warning:
ath12k_mac_destroy() error: we previously assumed 'ab' could be null
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/
Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340
Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw get helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle
to the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the
ath12k_hw set helper function takes the device handle and the index as
parameters. Here, the index parameter is specific to the group handle.
Therefore, change this helper function argument from the device handle to
the group handle.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250112071630.4059410-2-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
After a job completes, the corresponding pointer in the device must
be set to NULL. Failing to do so triggers a warning when unloading
the driver, as it appears the job is still active. To prevent this,
assign the job pointer to NULL after completing the job, indicating
the job has finished.
Fixes: 14d1d1908696 ("drm/v3d: Remove the bad signaled() implementation.")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113154741.67520-1-mcanal@igalia.com
|
|
Allow configuring the DPM watchdog to warn about slow suspend/resume
functions without causing a system panic(). This allows you to set the
DPM_WATCHDOG_WARNING_TIMEOUT to something like 5 or 10 seconds to get
warnings about slow suspend/resume functions that eventually succeed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://patch.msgid.link/20250109125957.v2.1.I4554f931b8da97948f308ecc651b124338ee9603@changeid
[ rjw: Subject edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover
boost frequencies") introduced an assumption in acpi_cpufreq_cpu_init()
that the first entry in the P-state table was the nominal frequency.
This assumption is incorrect. The frequency corresponding to the P0
P-State need not be the same as the nominal frequency advertised via
CPPC.
Since the driver is using the CPPC.highest_perf and CPPC.nominal_perf
to compute the boost-ratio, it makes sense to use CPPC.nominal_freq to
compute the max-frequency. CPPC.nominal_freq is advertised on
platforms supporting CPPC revisions 3 or higher.
Hence, fallback to using the first entry in the P-State table only on
platforms that do not advertise CPPC.nominal_freq.
Fixes: 3c55e94c0ade ("cpufreq: ACPI: Extend frequency tables to cover boost frequencies")
Tested-by: Dhananjay Ugwekar <Dhananjay.Ugwekar@amd.com>
Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://patch.msgid.link/20250113044107.566-1-gautham.shenoy@amd.com
[ rjw: Retain reverse X-mas tree ordering of local variable declarations ]
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
It is possible to enable few cpufreq drivers, without the framework
being enabled. This happened due to a bug while moving the entries
earlier. Fix it.
Fixes: 7ee1378736f0 ("cpufreq: Move CPPC configs to common Kconfig and add RISC-V")
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://patch.msgid.link/84ac7a8fa72a8fe20487bb0a350a758bce060965.1736488384.git.viresh.kumar@linaro.org
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fix from Bjorn Helgaas:
- Prevent bwctrl NULL pointer dereference that caused hangs on shutdown
on ASUS ROG Strix SCAR 17 G733PYV (Lukas Wunner)
* tag 'pci-v6.13-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Fix NULL pointer deref on unbind and bind
|
|
Since commit 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer
overflow in flexible-array member access"), the clk provider register is
failed.
The count of `clks_num` is shown below:
for (p = data; p->name; p++)
clks_num++;
In fact, `clks_num` represents the number of SoC clocks and should be
expressed as the maximum value of the clock binding id in use (p->id + 1).
Now we fix it to avoid the following error when trying to register a clk
provider:
[ 13.409595] of_clk_hw_onecell_get: invalid index 17
Cc: stable@vger.kernel.org
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Fixes: 02fb4f008433 ("clk: clk-loongson2: Fix potential buffer overflow in flexible-array member access")
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/82e43d89a9a6791129cf8ea14f4eeb666cd87be4.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Since commit 706ae6446494 ("clk: fixed-rate: add
devm_clk_hw_register_fixed_rate_parent_data()"), we can use the
devm_clk_hw_register_fixed_rate_parent_data() helper and from then on
there is no need to manually unregister the fixed rate hw.
Since clk_hw_unregister_fixed_rate() was not called before, we also fix
the memory leak that was present.
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/8733a7485619bdb791de25201a3d7984d1849c9f.1736856470.git.zhoubinbin@loongson.cn
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Tariq Toukan says:
====================
mlx5-next updates 2025-01-14
The following pull-request contains mlx5 IFC updates.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: Add nic_cap_reg and vhca_icm_ctrl registers
net/mlx5: SHAMPO: Introduce new SHAMPO specific HCA caps
net/mlx5: Add support for MRTCQ register
net/mlx5: Update mlx5_ifc to support FEC for 200G per lane link modes
====================
Link: https://patch.msgid.link/20250114055700.1928736-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce num_reg to store the number of clocks, this helps to make
_clk_get become a common helper function which called jh71x0_clk_get().
With this, it helps to simplify the code and extend the code in the
future.
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20250114081300.36600-1-changhuang.liang@starfivetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"One iscsi driver fix and one core fix.
The core fix is an important one because a retry efficiency update is
now causing some USB devices to get the wrong size on discovery (it
upset their retry logic for READ_CAPACITY_16)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: Fix redundant response for ISCSI_UEVENT_GET_HOST_STATS request
scsi: core: Fix command pass through retry regression
|
|
Adds a new BO param that keeps the reservation locked after creation.
This removes the need to re-reserve the BO after creation which is a
waste of cycles.
This also fixes a bug in vmw_prime_import_sg_table where the imported
reservation is unlocked twice.
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Fixes: b32233acceff ("drm/vmwgfx: Fix prime import/export")
Reviewed-by: Zack Rusin <zack.rusin@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110185335.15301-1-ian.forbes@broadcom.com
|
|
Unused since commit a78a8da51b36
("drm/ttm: replace busy placement with flags v6")
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Reviewed-by: Martin Krastev <martin.krastev@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250108201355.2521070-1-ian.forbes@broadcom.com
|
|
Unlock BOs in reverse order.
Add an acquire context so that lockdep doesn't complain.
Fixes: d6667f0ddf46 ("drm/vmwgfx: Fix handling of dumb buffers")
Signed-off-by: Ian Forbes <ian.forbes@broadcom.com>
Signed-off-by: Zack Rusin <zack.rusin@broadcom.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241210195535.2074918-1-ian.forbes@broadcom.com
|
|
The recently introduced hotplug event handler in the HDMI Connector
framework attempts to unconditionally read the EDID data, leading to a
bunch of non-harmful, yet quite annoying DDC/I2C related errors being
reported.
Ensure the operation is done only for connectors having the status
connected or unknown. Additionally, perform an explicit reset of the
connector information when dealing with a disconnected status.
Fixes: ab716b74dc9d ("drm/display/hdmi: implement hotplug functions")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250113-hdmi-conn-edid-read-fix-v2-1-d2a0438a44ab@collabora.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Atomic check should succeed when disabling a connector. Add a test
case drm_test_check_disabling_connector() to make sure of this.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110084821.3239518-3-victor.liu@nxp.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
It's ok to pass atomic check successfully if an atomic commit tries to
disable the display pipeline which the connector belongs to. That is,
when the crtc or the best_encoder pointers in struct drm_connector_state
are NULL, drm_atomic_helper_connector_hdmi_check() should return 0.
Without the check against the NULL pointers, drm_default_rgb_quant_range()
called by drm_atomic_helper_connector_hdmi_check() would dereference
the NULL pointer to_match in drm_match_cea_mode().
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
drm_default_rgb_quant_range+0x0/0x4c (P)
drm_bridge_connector_atomic_check+0x20/0x2c
drm_atomic_helper_check_modeset+0x488/0xc78
drm_atomic_helper_check+0x20/0xa4
drm_atomic_check_only+0x4b8/0x984
drm_atomic_commit+0x48/0xc4
drm_framebuffer_remove+0x44c/0x530
drm_mode_rmfb_work_fn+0x7c/0xa0
process_one_work+0x150/0x294
worker_thread+0x2dc/0x3dc
kthread+0x130/0x204
ret_from_fork+0x10/0x20
Fixes: 8ec116ff21a9 ("drm/display: bridge_connector: provide atomic_check for HDMI bridges")
Fixes: 84e541b1e58e ("drm/sun4i: use drm_atomic_helper_connector_hdmi_check()")
Fixes: 65548c8ff0ab ("drm/rockchip: inno_hdmi: Switch to HDMI connector")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20250110084821.3239518-2-victor.liu@nxp.com
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
The GHES driver overrides the panic= setting by force-rebooting the
system after a fatal hw error has been reported. The intent being that
such an error would be reported earlier.
However, this is not optimal when a hard-to-debug issue requires long
time to reproduce and when that happens, the box will get rebooted after
30 seconds and thus destroy the whole hw context of when the error
happened.
So rip out the default GHES panic timeout and honor the global one.
In the panic disabled (panic=0) case, the error will still be logged to
dmesg for later inspection and if panic after a hw error is really
required, then that can be controlled the usual way - use panic= on the
cmdline or set it in the kernel .config's CONFIG_PANIC_TIMEOUT.
Reported-by: Feng Tang <feng.tang@linux.alibaba.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Feng Tang <feng.tang@linux.alibaba.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Link: https://patch.msgid.link/20250113125224.GFZ4UMiNtWIJvgpveU@fat_crate.local
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
FW attestation was disabled on MP0_14_0_{2/3}.
V2:
Move check into is_fw_attestation_support func. (Frank)
Remove DRM_WARN log info. (Alex)
Fix format. (Christian)
Signed-off-by: Gui Chengming <Jack.Gui@amd.com>
Reviewed-by: Frank.Min <Frank.Min@amd.com>
Reviewed-by: Christian König <Christian.Koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 62952a38d9bcf357d5ffc97615c48b12c9cd627c)
Cc: stable@vger.kernel.org # 6.12.x
|
|
That is needed to enforce isolation between contexts.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit def59436fb0d3ca0f211d14873d0273d69ebb405)
Cc: stable@vger.kernel.org
|
|
Disable gfxoff with the compute workload on gfx12. This is a
workaround for the opencl test failure.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 2affe2bbc997b3920045c2c434e480c81a5f9707)
Cc: stable@vger.kernel.org # 6.12.x
|
|
This commit addresses a circular locking dependency issue within the GFX
isolation mechanism. The problem was identified by a warning indicating
a potential deadlock due to inconsistent lock acquisition order.
- The `amdgpu_gfx_enforce_isolation_ring_begin_use` and
`amdgpu_gfx_enforce_isolation_ring_end_use` functions previously
acquired `enforce_isolation_mutex` and called `amdgpu_gfx_kfd_sch_ctrl`,
leading to potential deadlocks. ie., If `amdgpu_gfx_kfd_sch_ctrl` is
called while `enforce_isolation_mutex` is held, and
`amdgpu_gfx_enforce_isolation_handler` is called while `kfd_sch_mutex` is
held, it can create a circular dependency.
By ensuring consistent lock usage, this fix resolves the issue:
[ 606.297333] ======================================================
[ 606.297343] WARNING: possible circular locking dependency detected
[ 606.297353] 6.10.0-amd-mlkd-610-311224-lof #19 Tainted: G OE
[ 606.297365] ------------------------------------------------------
[ 606.297375] kworker/u96:3/3825 is trying to acquire lock:
[ 606.297385] ffff9aa64e431cb8 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}, at: __flush_work+0x232/0x610
[ 606.297413]
but task is already holding lock:
[ 606.297423] ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu]
[ 606.297725]
which lock already depends on the new lock.
[ 606.297738]
the existing dependency chain (in reverse order) is:
[ 606.297749]
-> #2 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}:
[ 606.297765] __mutex_lock+0x85/0x930
[ 606.297776] mutex_lock_nested+0x1b/0x30
[ 606.297786] amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu]
[ 606.298007] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu]
[ 606.298225] amdgpu_ring_alloc+0x48/0x70 [amdgpu]
[ 606.298412] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu]
[ 606.298603] amdgpu_job_run+0xac/0x1e0 [amdgpu]
[ 606.298866] drm_sched_run_job_work+0x24f/0x430 [gpu_sched]
[ 606.298880] process_one_work+0x21e/0x680
[ 606.298890] worker_thread+0x190/0x350
[ 606.298899] kthread+0xe7/0x120
[ 606.298908] ret_from_fork+0x3c/0x60
[ 606.298919] ret_from_fork_asm+0x1a/0x30
[ 606.298929]
-> #1 (&adev->enforce_isolation_mutex){+.+.}-{3:3}:
[ 606.298947] __mutex_lock+0x85/0x930
[ 606.298956] mutex_lock_nested+0x1b/0x30
[ 606.298966] amdgpu_gfx_enforce_isolation_handler+0x87/0x370 [amdgpu]
[ 606.299190] process_one_work+0x21e/0x680
[ 606.299199] worker_thread+0x190/0x350
[ 606.299208] kthread+0xe7/0x120
[ 606.299217] ret_from_fork+0x3c/0x60
[ 606.299227] ret_from_fork_asm+0x1a/0x30
[ 606.299236]
-> #0 ((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work)){+.+.}-{0:0}:
[ 606.299257] __lock_acquire+0x16f9/0x2810
[ 606.299267] lock_acquire+0xd1/0x300
[ 606.299276] __flush_work+0x250/0x610
[ 606.299286] cancel_delayed_work_sync+0x71/0x80
[ 606.299296] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu]
[ 606.299509] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu]
[ 606.299723] amdgpu_ring_alloc+0x48/0x70 [amdgpu]
[ 606.299909] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu]
[ 606.300101] amdgpu_job_run+0xac/0x1e0 [amdgpu]
[ 606.300355] drm_sched_run_job_work+0x24f/0x430 [gpu_sched]
[ 606.300369] process_one_work+0x21e/0x680
[ 606.300378] worker_thread+0x190/0x350
[ 606.300387] kthread+0xe7/0x120
[ 606.300396] ret_from_fork+0x3c/0x60
[ 606.300406] ret_from_fork_asm+0x1a/0x30
[ 606.300416]
other info that might help us debug this:
[ 606.300428] Chain exists of:
(work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work) --> &adev->enforce_isolation_mutex --> &adev->gfx.kfd_sch_mutex
[ 606.300458] Possible unsafe locking scenario:
[ 606.300468] CPU0 CPU1
[ 606.300476] ---- ----
[ 606.300484] lock(&adev->gfx.kfd_sch_mutex);
[ 606.300494] lock(&adev->enforce_isolation_mutex);
[ 606.300508] lock(&adev->gfx.kfd_sch_mutex);
[ 606.300521] lock((work_completion)(&(&adev->gfx.enforce_isolation[i].work)->work));
[ 606.300536]
*** DEADLOCK ***
[ 606.300546] 5 locks held by kworker/u96:3/3825:
[ 606.300555] #0: ffff9aa5aa1f5d58 ((wq_completion)comp_1.1.0){+.+.}-{0:0}, at: process_one_work+0x3f5/0x680
[ 606.300577] #1: ffffaa53c3c97e40 ((work_completion)(&sched->work_run_job)){+.+.}-{0:0}, at: process_one_work+0x1d6/0x680
[ 606.300600] #2: ffff9aa64e463c98 (&adev->enforce_isolation_mutex){+.+.}-{3:3}, at: amdgpu_gfx_enforce_isolation_ring_begin_use+0x1c3/0x5d0 [amdgpu]
[ 606.300837] #3: ffff9aa64e432338 (&adev->gfx.kfd_sch_mutex){+.+.}-{3:3}, at: amdgpu_gfx_kfd_sch_ctrl+0x51/0x4d0 [amdgpu]
[ 606.301062] #4: ffffffff8c1a5660 (rcu_read_lock){....}-{1:2}, at: __flush_work+0x70/0x610
[ 606.301083]
stack backtrace:
[ 606.301092] CPU: 14 PID: 3825 Comm: kworker/u96:3 Tainted: G OE 6.10.0-amd-mlkd-610-311224-lof #19
[ 606.301109] Hardware name: Gigabyte Technology Co., Ltd. X570S GAMING X/X570S GAMING X, BIOS F7 03/22/2024
[ 606.301124] Workqueue: comp_1.1.0 drm_sched_run_job_work [gpu_sched]
[ 606.301140] Call Trace:
[ 606.301146] <TASK>
[ 606.301154] dump_stack_lvl+0x9b/0xf0
[ 606.301166] dump_stack+0x10/0x20
[ 606.301175] print_circular_bug+0x26c/0x340
[ 606.301187] check_noncircular+0x157/0x170
[ 606.301197] ? register_lock_class+0x48/0x490
[ 606.301213] __lock_acquire+0x16f9/0x2810
[ 606.301230] lock_acquire+0xd1/0x300
[ 606.301239] ? __flush_work+0x232/0x610
[ 606.301250] ? srso_alias_return_thunk+0x5/0xfbef5
[ 606.301261] ? mark_held_locks+0x54/0x90
[ 606.301274] ? __flush_work+0x232/0x610
[ 606.301284] __flush_work+0x250/0x610
[ 606.301293] ? __flush_work+0x232/0x610
[ 606.301305] ? __pfx_wq_barrier_func+0x10/0x10
[ 606.301318] ? mark_held_locks+0x54/0x90
[ 606.301331] ? srso_alias_return_thunk+0x5/0xfbef5
[ 606.301345] cancel_delayed_work_sync+0x71/0x80
[ 606.301356] amdgpu_gfx_kfd_sch_ctrl+0x287/0x4d0 [amdgpu]
[ 606.301661] amdgpu_gfx_enforce_isolation_ring_begin_use+0x2a4/0x5d0 [amdgpu]
[ 606.302050] ? srso_alias_return_thunk+0x5/0xfbef5
[ 606.302069] amdgpu_ring_alloc+0x48/0x70 [amdgpu]
[ 606.302452] amdgpu_ib_schedule+0x176/0x8a0 [amdgpu]
[ 606.302862] ? drm_sched_entity_error+0x82/0x190 [gpu_sched]
[ 606.302890] amdgpu_job_run+0xac/0x1e0 [amdgpu]
[ 606.303366] drm_sched_run_job_work+0x24f/0x430 [gpu_sched]
[ 606.303388] process_one_work+0x21e/0x680
[ 606.303409] worker_thread+0x190/0x350
[ 606.303424] ? __pfx_worker_thread+0x10/0x10
[ 606.303437] kthread+0xe7/0x120
[ 606.303449] ? __pfx_kthread+0x10/0x10
[ 606.303463] ret_from_fork+0x3c/0x60
[ 606.303476] ? __pfx_kthread+0x10/0x10
[ 606.303489] ret_from_fork_asm+0x1a/0x30
[ 606.303512] </TASK>
v2: Refactor lock handling to resolve circular dependency (Alex)
- Introduced a `sched_work` flag to defer the call to
`amdgpu_gfx_kfd_sch_ctrl` until after releasing
`enforce_isolation_mutex`.
- This change ensures that `amdgpu_gfx_kfd_sch_ctrl` is called outside
the critical section, preventing the circular dependency and deadlock.
- The `sched_work` flag is set within the mutex-protected section if
conditions are met, and the actual function call is made afterward.
- This approach ensures consistent lock acquisition order.
Fixes: afefd6f24502 ("drm/amdgpu: Implement Enforce Isolation Handler for KGD/KFD serialization")
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 0b6b2dd38336d5fd49214f0e4e6495e658e3ab44)
Cc: stable@vger.kernel.org
|
|
The yt2_1380_fc_serdev_probe() function calls devm_serdev_device_open()
before setting the client ops via serdev_device_set_client_ops(). This
ordering can trigger a NULL pointer dereference in the serdev controller's
receive_buf handler, as it assumes serdev->ops is valid when
SERPORT_ACTIVE is set.
This is similar to the issue fixed in commit 5e700b384ec1
("platform/chrome: cros_ec_uart: properly fix race condition") where
devm_serdev_device_open() was called before fully initializing the
device.
Fix the race by ensuring client ops are set before enabling the port via
devm_serdev_device_open().
Note, serdev_device_set_baudrate() and serdev_device_set_flow_control()
calls should be after the devm_serdev_device_open() call.
Fixes: b2ed33e8d486 ("platform/x86: Add lenovo-yoga-tab2-pro-1380-fastcharger driver")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250111180951.2277757-1-chenyuan0y@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The dell_uart_bl_serdev_probe() function calls devm_serdev_device_open()
before setting the client ops via serdev_device_set_client_ops(). This
ordering can trigger a NULL pointer dereference in the serdev controller's
receive_buf handler, as it assumes serdev->ops is valid when
SERPORT_ACTIVE is set.
This is similar to the issue fixed in commit 5e700b384ec1
("platform/chrome: cros_ec_uart: properly fix race condition") where
devm_serdev_device_open() was called before fully initializing the
device.
Fix the race by ensuring client ops are set before enabling the port via
devm_serdev_device_open().
Note, serdev_device_set_baudrate() and serdev_device_set_flow_control()
calls should be after the devm_serdev_device_open() call.
Fixes: 484bae9e4d6a ("platform/x86: Add new Dell UART backlight driver")
Signed-off-by: Chenyuan Yang <chenyuan0y@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20250111180118.2274516-1-chenyuan0y@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
Here is a (big) series supposed to bring DTR support in SPI-NAND.
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() combined with getting the syscon
argument. Except simpler code this annotates within one line that given
phandle has arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250111185400.183760-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
After commit e6204f39fe3a ("spi: amd: Drop redundant check"), clang warns (or
errors with CONFIG_WERROR=y):
drivers/spi/spi-amd.c:695:9: error: variable 'ret' is uninitialized when used here [-Werror,-Wuninitialized]
695 | return ret;
| ^~~
drivers/spi/spi-amd.c:673:9: note: initialize the variable 'ret' to silence this warning
673 | int ret;
| ^
| = 0
1 error generated.
ret is no longer set on anything other than the default switch path.
Replace ret with a direct return of 0 at the end of the function and
-EOPNOTSUPP in the default case to resolve the warning.
Fixes: e6204f39fe3a ("spi: amd: Drop redundant check")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501112315.ugYQ7Ce7-lkp@intel.com/
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20250111-spi-amd-fix-uninitialized-ret-v1-1-c66ab9f6a23d@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
namespaces
DEFAULT_SYMBOL_NAMESPACE must already be defined when <linux/export.h>
is included. So move the define above the include block.
Fixes: fd57a3325a77 ("i2c: designware: Move exports to I2C_DW namespaces")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
irq_chip functions may be called in raw spinlock context. Therefore, we
must also use a raw spinlock for our own internal locking.
This fixes the following lockdep splat:
[ 5.349336] =============================
[ 5.353349] [ BUG: Invalid wait context ]
[ 5.357361] 6.13.0-rc5+ #69 Tainted: G W
[ 5.363031] -----------------------------
[ 5.367045] kworker/u17:1/44 is trying to lock:
[ 5.371587] ffffff88018b02c0 (&chip->gpio_lock){....}-{3:3}, at: xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8))
[ 5.380079] other info that might help us debug this:
[ 5.385138] context-{5:5}
[ 5.387762] 5 locks held by kworker/u17:1/44:
[ 5.392123] #0: ffffff8800014958 ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3204)
[ 5.402260] #1: ffffffc082fcbdd8 (deferred_probe_work){+.+.}-{0:0}, at: process_one_work (kernel/workqueue.c:3205)
[ 5.411528] #2: ffffff880172c900 (&dev->mutex){....}-{4:4}, at: __device_attach (drivers/base/dd.c:1006)
[ 5.419929] #3: ffffff88039c8268 (request_class#2){+.+.}-{4:4}, at: __setup_irq (kernel/irq/internals.h:156 kernel/irq/manage.c:1596)
[ 5.428331] #4: ffffff88039c80c8 (lock_class#2){....}-{2:2}, at: __setup_irq (kernel/irq/manage.c:1614)
[ 5.436472] stack backtrace:
[ 5.439359] CPU: 2 UID: 0 PID: 44 Comm: kworker/u17:1 Tainted: G W 6.13.0-rc5+ #69
[ 5.448690] Tainted: [W]=WARN
[ 5.451656] Hardware name: xlnx,zynqmp (DT)
[ 5.455845] Workqueue: events_unbound deferred_probe_work_func
[ 5.461699] Call trace:
[ 5.464147] show_stack+0x18/0x24 C
[ 5.467821] dump_stack_lvl (lib/dump_stack.c:123)
[ 5.471501] dump_stack (lib/dump_stack.c:130)
[ 5.474824] __lock_acquire (kernel/locking/lockdep.c:4828 kernel/locking/lockdep.c:4898 kernel/locking/lockdep.c:5176)
[ 5.478758] lock_acquire (arch/arm64/include/asm/percpu.h:40 kernel/locking/lockdep.c:467 kernel/locking/lockdep.c:5851 kernel/locking/lockdep.c:5814)
[ 5.482429] _raw_spin_lock_irqsave (include/linux/spinlock_api_smp.h:111 kernel/locking/spinlock.c:162)
[ 5.486797] xgpio_irq_unmask (drivers/gpio/gpio-xilinx.c:433 (discriminator 8))
[ 5.490737] irq_enable (kernel/irq/internals.h:236 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
[ 5.494060] __irq_startup (kernel/irq/internals.h:241 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
[ 5.497645] irq_startup (kernel/irq/chip.c:270)
[ 5.501143] __setup_irq (kernel/irq/manage.c:1807)
[ 5.504728] request_threaded_irq (kernel/irq/manage.c:2208)
Fixes: a32c7caea292 ("gpio: gpio-xilinx: Add interrupt support")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250110163354.2012654-1-sean.anderson@linux.dev
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
Remove PSE-specific structures from the ethtool header to improve code
modularity, maintain independent headers, and reduce incremental build
time.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The PI of_node was not assigned in the regulator_config structure, leading
to failures in resolving the correct supply when different power supplies
are assigned to multiple PIs of a PSE controller. This fix ensures that the
of_node is properly set in the regulator_config, allowing accurate supply
resolution for each PI.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Expand PSE callbacks to support the newly introduced
pi_get/set_pw_limit() and pi_get_voltage() functions. These callbacks
allow for power limit configuration in the TPS23881 controller.
Additionally, the patch includes the pi_get_pw_class() the
pi_get_actual_pw(), and the pi_get_pw_limit_ranges') callbacks providing
more comprehensive PoE status reporting.
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
