| Age | Commit message (Collapse) | Author |
|---|
|
KSZ8463 uses 16-bit register definitions so it writes differently for
8-bit switch MAC address.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250725001753.6330-5-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 does not use same set of registers as KSZ8863 so it is necessary
to change some registers when using KSZ8463.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250725001753.6330-4-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
KSZ8463 switch is a 3-port switch based from KSZ8863. Its major
difference from other KSZ SPI switches is its register access is not a
simple continual 8-bit transfer with automatic address increase but uses
a byte-enable mechanism specifying 8-bit, 16-bit, or 32-bit access. Its
registers are also defined in 16-bit format because it shares a design
with a MAC controller using 16-bit access. As a result some common
register accesses need to be re-arranged.
This patch adds the basic structure for using KSZ8463. It cannot use the
same regmap table for other KSZ switches as it interprets the 16-bit
value as little-endian and its SPI commands are different.
KSZ8463 uses a byte-enable mechanism to specify 8-bit, 16-bit, and 32-bit
access. The register is first shifted right by 2 then left by 4. Extra
4 bits are added. If the access is 8-bit one of the 4 bits is set. If
the access is 16-bit two of the 4 bits are set. If the access is 32-bit
all 4 bits are set. The SPI command for read or write is then added.
Because of this register transformation separate SPI read and write
functions are provided for KSZ8463.
KSZ8463's internal PHYs use standard PHY register definitions so there is
no need to remap things. However, the hardware has a bug that the high
word and low word of the PHY id are swapped. In addition the port
registers are arranged differently so KSZ8463 has its own mapping for
port registers and PHY registers. Therefore the PORT_CTRL_ADDR macro is
replaced with the get_port_addr helper function.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250725001753.6330-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Agilex5 compatible value.
Signed-off-by: Mun Yew Tham <mun.yew.tham@altera.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@altera.com>
Link: https://patch.msgid.link/20250724154052.205706-5-matthew.gerlach@altera.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2025-07-25
The first patch is by Khaled Elnaggar and converts the janz-ican3
driver's fwinfo_show() to sysfs_emit().
Vincent Mailhol contributes 3 patches that first fix a warning in the
ti_hecc driver and then add missing COMPILE_TEST more compile
coverage to the ti_hecc and tscan1 driver.
Randy Dunlap's patch let's the tscan1 driver depend on PC104.
A patch by Luis Felipe Hernandez fixes a kernel-doc error in the
ctucanfd driver.
Jimmy Assarsson contributes 10 patches for the kvaser_pciefd and 11
for the kvaser_usb driver. Both series simplify the identification of
physical the CAN interfaces and add devlink support to get information
about the running firmware.
* tag 'linux-can-next-for-6.17-20250725' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (27 commits)
Documentation: devlink: add devlink documentation for the kvaser_usb driver
can: kvaser_usb: Add devlink port support
can: kvaser_usb: Expose device information via devlink info_get()
can: kvaser_usb: Add devlink support
can: kvaser_usb: Store additional device information
can: kvaser_usb: Store the different firmware version components in a struct
can: kvaser_usb: Move comment regarding max_tx_urbs
can: kvaser_usb: Add intermediate variables
can: kvaser_usb: Assign netdev.dev_port based on device channel index
can: kvaser_usb: Add support for ethtool set_phys_id()
can: kvaser_usb: Add support to control CAN LEDs on device
Documentation: devlink: add devlink documentation for the kvaser_pciefd driver
can: kvaser_pciefd: Add devlink port support
can: kvaser_pciefd: Expose device firmware version via devlink info_get()
can: kvaser_pciefd: Add devlink support
can: kvaser_pciefd: Split driver into C-file and header-file.
can: kvaser_pciefd: Store device channel index
can: kvaser_pciefd: Store the different firmware version components in a struct
can: kvaser_pciefd: Add intermediate variable for device struct in probe()
can: kvaser_pciefd: Add support for ethtool set_phys_id()
...
====================
Link: https://patch.msgid.link/20250725161327.4165174-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
libie: commonize adminq structure
Michal Swiatkowski says:
It is a prework to allow reusing some specific Intel code (eq. fwlog).
Move common *_aq_desc structure to libie header and changing
it in ice, ixgbe, i40e and iavf.
Only generic adminq commands can be easily moved to common header, as
rest is slightly different. Format remains the same. It will be better
to correctly move it when it will be needed to commonize other part of
the code.
Move *_aq_str() to new libie module (libie_adminq) and use it across
drivers. The functions are exactly the same in each driver. Some more
adminq helpers/functions can be moved to libie_adminq when needed.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
i40e: use libie_aq_str
iavf: use libie_aq_str
ice: use libie_aq_str
libie: add adminq helper for converting err to str
iavf: use libie adminq descriptors
i40e: use libie adminq descriptors
ixgbe: use libie adminq descriptors
ice, libie: move generic adminq descriptors to lib
====================
Link: https://patch.msgid.link/20250724182826.3758850-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As part of the removal of the variably-sized sockaddr for kernel
internals, replace struct sockaddr with sockaddr_inet in the endpoint
union.
No binary changes; the union size remains unchanged due to sockaddr_inet
matching the size of sockaddr_in6.
Signed-off-by: Kees Cook <kees@kernel.org>
Link: https://patch.msgid.link/20250722171836.1078436-2-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Underneath "TIS Config" tag expose TIS diagnostic information.
Expose the tisn of each TC under each lag port.
$ sudo devlink health diagnose auxiliary/mlx5_core.eth.2/131072 reporter tx
......
TIS Config:
lag port: 0 tc: 0 tisn: 0
lag port: 1 tc: 0 tisn: 8
......
Signed-off-by: Feng Liu <feliu@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1753194228-333722-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remote IPsec tunnel endpoint may refer to a network segment that is
not directly connected to the host. In such a case, IPsec tunnel
endpoints are connected to a router and reachable via a routing path.
In IPsec packet offload mode, HW is initialized with the MAC address
of both IPsec tunnel endpoints.
Extend the current IPsec init MACs procedure to resolve nexthop for
routed networks. Direct neighbour lookup and probe is still used
for directly connected networks and as a fallback mechanism if fib
lookup fails.
Signed-off-by: Alexandre Cassen <acassen@corp.free.fr>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/1753194228-333722-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement the phy enable/disable calls for b53 mmap, and
set the power down registers in the ephy control register
appropriately.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-8-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ephy register info for bcm6368.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-7-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add ephy register info for bcm6318, which also applies to
bcm6328 and bcm6362.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-6-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On bcm63xx SoCs there are registers that control the PHYs in
the GPIO controller. Allow the b53 driver to access them
by passing in the syscon through the device tree.
Add a structure to describe the ephy control register
and add register info for bcm63268.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-5-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add defines for bcm6318, bcm6328, bcm6362, bcm6368 chip IDs,
update tables and switch init.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-4-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add phy enable/disable to b53 ops to be called when
enabling/disabling ports.
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250724035300.20497-2-kylehendrydev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The local variable i is used to iterate over unsigned
values. The lower bound of the loop is set to 0. While
the upper bound is cgx->lmac_count, where they lmac_count is
an u8. So the theoretical upper bound is 255.
As is, GCC can't see this range of values and warns that
a formatted string, which includes the %d representation of i,
may overflow the buffer provided.
GCC 15.1.0 says:
.../cgx.c: In function 'cgx_lmac_init':
.../cgx.c:1737:49: warning: '%d' directive writing between 1 and 11 bytes into a region of size between 4 and 6 [-Wformat-overflow=]
1737 | sprintf(lmac->name, "cgx_fwi_%d_%d", cgx->cgx_id, i);
| ^~
.../cgx.c:1737:37: note: directive argument in the range [-2147483641, 254]
1737 | sprintf(lmac->name, "cgx_fwi_%d_%d", cgx->cgx_id, i);
| ^~~~~~~~~~~~~~~
.../cgx.c:1737:17: note: 'sprintf' output between 12 and 24 bytes into a destination of size 16
1737 | sprintf(lmac->name, "cgx_fwi_%d_%d", cgx->cgx_id, i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Empirically, changing the type of i from (signed) int to unsigned int
addresses this problem. I assume by allowing GCC to see the range of
values described above.
Also update the format specifiers for the integer values in the string
in question from %d to %u. This seems appropriate as they are now both
unsigned.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250724-octeontx2-af-unsigned-v1-1-c745c106e06f@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, USB CDC devices that do not use MDIO to get link status have
their duplex mode set to half-duplex by default. However, since the CDC
specification does not define a duplex status, this can be misleading.
This patch changes the default to DUPLEX_UNKNOWN in the absence of MII,
which more accurately reflects the state of the link and avoids implying
an incorrect or error state.
Link: https://lore.kernel.org/all/20250723152151.70a8034b@kernel.org/
Signed-off-by: Yi Cong <yicong@kylinos.cn>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://patch.msgid.link/20250724013133.1645142-1-yicongsrfy@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cosmin reports the following locking issue:
# BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:275
# dump_stack_lvl+0x4f/0x60
# __might_resched+0xeb/0x140
# mutex_lock+0x1a/0x40
# dev_set_promiscuity+0x26/0x90
# __dev_set_promiscuity+0x85/0x170
# __dev_set_rx_mode+0x69/0xa0
# dev_uc_add+0x6d/0x80
# vlan_dev_open+0x5f/0x120 [8021q]
# __dev_open+0x10c/0x2a0
# __dev_change_flags+0x1a4/0x210
# netif_change_flags+0x22/0x60
# do_setlink.isra.0+0xdb0/0x10f0
# rtnl_newlink+0x797/0xb00
# rtnetlink_rcv_msg+0x1cb/0x3f0
# netlink_rcv_skb+0x53/0x100
# netlink_unicast+0x273/0x3b0
# netlink_sendmsg+0x1f2/0x430
Which is similar to recent syzkaller reports in [0] and [1] and triggers
because macsec does not advertise IFF_UNICAST_FLT although it has proper
ndo_set_rx_mode callback that takes care of pushing uc/mc addresses
down to the real device.
In general, dev_uc_add call path is problematic for stacking
non-IFF_UNICAST_FLT because we might grab netdev instance lock under
addr_list_lock spinlock, so this is not a systemic fix.
0: https://lore.kernel.org/netdev/686d55b4.050a0220.1ffab7.0014.GAE@google.com
1: https://lore.kernel.org/netdev/68712acf.a00a0220.26a83e.0051.GAE@google.com/
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/netdev/2aff4342b0f5b1539c02ffd8df4c7e58dd9746e7.camel@nvidia.com
Fixes: 7e4d784f5810 ("net: hold netdev instance lock during rtnetlink operations")
Reported-by: Cosmin Ratiu <cratiu@nvidia.com>
Tested-by: Cosmin Ratiu <cratiu@nvidia.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250723224715.1341121-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a statistical item to count the number of reset failures.
This statistical item can be queried using ethtool -S or
reported through diagnose information.
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Link: https://patch.msgid.link/20250723074826.2756135-1-shaojijie@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix typos in comments and error messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250723201528.2908218-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Register each CAN channel of the device as an devlink physical port.
This makes it easier to get device information for a given network
interface (i.e. can2).
Example output:
$ devlink dev
usb/1-1.3:1.0
$ devlink port
usb/1-1.3:1.0/0: type eth netdev can0 flavour physical port 0 splittable false
usb/1-1.3:1.0/1: type eth netdev can1 flavour physical port 1 splittable false
$ devlink port show can1
usb/1-1.3:1.0/1: type eth netdev can1 flavour physical port 0 splittable false
$ devlink dev info
usb/1-1.3:1.0:
driver kvaser_usb
serial_number 1020
versions:
fixed:
board.rev 1
board.id 7330130009653
running:
fw 3.22.527
$ ethtool -i can1
driver: kvaser_usb
version: 6.12.10-arch1-1
firmware-version: 3.22.527
expansion-rom-version:
bus-info: 1-1.3:1.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-11-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Expose device information via devlink info_get():
* Serial number
* Firmware version
* Hardware revision
* EAN (product number)
Example output:
$ devlink dev
usb/1-1.2:1.0
$ devlink dev info
usb/1-1.2:1.0:
driver kvaser_usb
serial_number 1020
versions:
fixed:
board.rev 1
board.id 7330130009653
running:
fw 3.22.527
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add devlink support at device level.
Example output:
$ devlink dev
usb/1-1.3:1.0
$ devlink dev info
usb/1-1.3:1.0:
driver kvaser_usb
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Store additional device information; EAN (product number), serial_number
and hardware revision.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-8-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Store firmware version in kvaser_usb_fw_version struct, specifying the
different components of the version number.
And drop debug prinout of firmware version, since later patches will expose
it via the devlink interface.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Move comment regarding max_tx_urbs, to where the struct member is declared.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add intermediate variables, for readability and to simplify future patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Assign netdev.dev_port based on the device channel index, to indicate the
port number of the network device.
While this driver already uses netdev.dev_id for that purpose, dev_port is
more appropriate. However, retain dev_id to avoid potential regressions.
Fixes: 3e66d0138c05 ("can: populate netdev::dev_id for udev discrimination")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for ethtool set_phys_id(), to physically locate devices by
flashing a LED on the device.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support to turn on/off CAN LEDs on device.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123452.41-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Register each CAN channel of the device as an devlink physical port.
This makes it easier to get device information for a given network
interface (i.e. can2).
Example output:
$ devlink dev
pci/0000:07:00.0
pci/0000:08:00.0
pci/0000:09:00.0
$ devlink port
pci/0000:07:00.0/0: type eth netdev can0 flavour physical port 0 splittable false
pci/0000:07:00.0/1: type eth netdev can1 flavour physical port 1 splittable false
pci/0000:07:00.0/2: type eth netdev can2 flavour physical port 2 splittable false
pci/0000:07:00.0/3: type eth netdev can3 flavour physical port 3 splittable false
pci/0000:08:00.0/0: type eth netdev can4 flavour physical port 0 splittable false
pci/0000:08:00.0/1: type eth netdev can5 flavour physical port 1 splittable false
pci/0000:09:00.0/0: type eth netdev can6 flavour physical port 0 splittable false
pci/0000:09:00.0/1: type eth netdev can7 flavour physical port 1 splittable false
pci/0000:09:00.0/2: type eth netdev can8 flavour physical port 2 splittable false
pci/0000:09:00.0/3: type eth netdev can9 flavour physical port 3 splittable false
$ devlink port show can2
pci/0000:07:00.0/2: type eth netdev can2 flavour physical port 2 splittable false
$ devlink dev info
pci/0000:07:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.75
pci/0000:08:00.0:
driver kvaser_pciefd
versions:
running:
fw 2.4.29
pci/0000:09:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.72
$ sudo ethtool -i can2
driver: kvaser_pciefd
version: 6.8.0-40-generic
firmware-version: 1.3.75
expansion-rom-version:
bus-info: 0000:07:00.0
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-10-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Expose device firmware version via devlink info_get().
Example output:
$ devlink dev
pci/0000:07:00.0
pci/0000:08:00.0
pci/0000:09:00.0
$ devlink dev info
pci/0000:07:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.75
pci/0000:08:00.0:
driver kvaser_pciefd
versions:
running:
fw 2.4.29
pci/0000:09:00.0:
driver kvaser_pciefd
versions:
running:
fw 1.3.72
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-9-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add devlink support at device level.
Example output:
$ devlink dev
pci/0000:07:00.0
pci/0000:08:00.0
pci/0000:09:00.0
$ devlink dev info
pci/0000:07:00.0:
driver kvaser_pciefd
pci/0000:08:00.0:
driver kvaser_pciefd
pci/0000:09:00.0:
driver kvaser_pciefd
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-8-extja@kvaser.com
[mkl: kvaser_pciefd_remove(): fix use-after-free]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Split driver into C-file and header-file, to simplify future patches.
Move common definitions and declarations to a header file.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-7-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Store device channel index in netdev.dev_port.
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-6-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Store firmware version in kvaser_pciefd_fw_version struct, specifying the
different components of the version number.
And drop debug prinout of firmware version, since later patches will expose
it via the devlink interface.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-5-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add intermediate variable, for readability and to simplify future patches.
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-4-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support for ethtool set_phys_id(), to physically locate devices by
flashing a LED on the device.
Reviewed-by: Axel Forsman <axfo@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-3-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add support to turn on/off CAN LEDs on device.
Turn off all CAN LEDs in probe, since they are default on after a reset or
power on.
Reviewed-by: Axel Forsman <axfo@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Link: https://patch.msgid.link/20250725123230.8-2-extja@kvaser.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix kernel-doc formatting issue causing unexpected indentation error
in ctucanfd driver documentation build. Convert main return values
to bullet list format while preserving numbered sub-list in order to
correct indentation error and visual structure in rendered html.
Signed-off-by: Luis Felipe Hernandez <luis.hernandez093@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Reviewed-by: Pavel Pisa <pisa@fel.cvut.cz>
Link: https://patch.msgid.link/20250722035352.21807-1-luis.hernandez093@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add a dependency on PC104 to limit (restrict) this driver kconfig
prompt to kernel configs that have PC104 set.
Add COMPILE_TEST as a possibility for more complete build coverage.
I tested this build config on x86_64 5 times without problems.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20250721002823.3548945-1-rdunlap@infradead.org
[mkl: fix conflict, remove Fixes: tag]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When building, the following warnings will appear.
"
pci_irq.c: In function ‘mlx5_ctrl_irq_request’:
pci_irq.c:494:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
pci_irq.c: In function ‘mlx5_irq_request_vector’:
pci_irq.c:561:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
eq.c: In function ‘comp_irq_request_sf’:
eq.c:897:1: warning: the frame size of 1080 bytes is larger than 1024 bytes [-Wframe-larger-than=]
irq_affinity.c: In function ‘irq_pool_request_irq’:
irq_affinity.c:74:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
"
These warnings indicate that the stack frame size exceeds 1024 bytes in
these functions.
To resolve this, instead of allocating large memory buffers on the stack,
it is better to use kvzalloc to allocate memory dynamically on the heap.
This approach reduces stack usage and eliminates these frame size warnings.
Acked-by: Junxian Huang <huangjunxian6@hisilicon.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250722212023.244296-1-yanjun.zhu@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare for adding an enum type for NAPI threaded states by adding
netif_threaded_enable API. De-export the existing netif_set_threaded API
and only use it internally. Update existing drivers to use
netif_threaded_enable instead of the de-exported netif_set_threaded.
Note that dev_set_threaded used by mt76 debugfs file is unchanged.
Signed-off-by: Samiullah Khawaja <skhawaja@google.com>
Link: https://patch.msgid.link/20250723013031.2911384-3-skhawaja@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
core:
- hci_sync: fix double free in 'hci_discovery_filter_clear()'
- hci_event: Mask data status from LE ext adv reports
- hci_devcd_dump: fix out-of-bounds via dev_coredumpv
- ISO: add socket option to report packet seqnum via CMSG
- hci_event: Add support for handling LE BIG Sync Lost event
- ISO: Support SCM_TIMESTAMPING for ISO TS
- hci_core: Add PA_LINK to distinguish BIG sync and PA sync connections
- hci_sock: Reset cookie to zero in hci_sock_free_cookie()
drivers:
- btusb: Add new VID/PID 0489/e14e for MT7925
- btusb: Add a new VID/PID 2c7c/7009 for MT7925
- btusb: Add RTL8852BE device 0x13d3:0x3618
- btusb: Add support for variant of RTL8851BE (USB ID 13d3:3601)
- btusb: Add USB ID 3625:010b for TP-LINK Archer TX10UB Nano
- btusb: QCA: Support downloading custom-made firmwares
- btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
- nxp: add support for supply and reset
- btnxpuart: Add support for 4M baudrate
- btnxpuart: Correct the Independent Reset handling after FW dump
- btnxpuart: Add uevents for FW dump and FW download complete
- btintel: Define a macro for Intel Reset vendor command
- btintel_pcie: Support Function level reset
- btintel_pcie: Add support for device 0x4d76
- btintel_pcie: Make driver wait for alive interrupt
- btintel_pcie: Fix Alive Context State Handling
- hci_qca: Enable ISO data packet RX
* tag 'for-net-next-2025-07-23' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (42 commits)
Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections
Bluetooth: hci_event: Mask data status from LE ext adv reports
Bluetooth: btintel_pcie: Fix Alive Context State Handling
Bluetooth: btintel_pcie: Make driver wait for alive interrupt
Bluetooth: hci_devcd_dump: fix out-of-bounds via dev_coredumpv
Bluetooth: hci_sync: fix double free in 'hci_discovery_filter_clear()'
Bluetooth: btusb: Add one more ID 0x28de:0x1401 for Qualcomm WCN6855
Bluetooth: btusb: Sort WCN6855 device IDs by VID and PID
Bluetooth: btusb: QCA: Support downloading custom-made firmwares
Bluetooth: btnxpuart: Add uevents for FW dump and FW download complete
Bluetooth: btnxpuart: Correct the Independent Reset handling after FW dump
Bluetooth: ISO: Support SCM_TIMESTAMPING for ISO TS
Bluetooth: ISO: add socket option to report packet seqnum via CMSG
Bluetooth: btintel: Define a macro for Intel Reset vendor command
Bluetooth: Fix typos in comments
Bluetooth: RFCOMM: Fix typos in comments
Bluetooth: aosp: Fix typo in comment
Bluetooth: hci_bcm4377: Fix typo in comment
Bluetooth: btrtl: Fix typo in comment
Bluetooth: btmtk: Fix typo in log string
...
====================
Link: https://patch.msgid.link/20250723190233.166823-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Another wireless update:
- rtw89:
- STA+P2P concurrency
- support for USB devices RTL8851BU/RTL8852BU
- ath9k: OF support
- ath12k:
- more EHT/Wi-Fi 7 features
- encapsulation/decapsulation offload
- iwlwifi: some FIPS interoperability
- brcm80211: support SDIO 43751 device
- rt2x00: better DT/OF support
- cfg80211/mac80211:
- improved S1G support
- beacon monitor for MLO
* tag 'wireless-next-2025-07-24' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (199 commits)
ssb: use new GPIO line value setter callbacks for the second GPIO chip
wifi: Fix typos
wifi: brcmsmac: Use str_true_false() helper
wifi: brcmfmac: fix EXTSAE WPA3 connection failure due to AUTH TX failure
wifi: brcm80211: Remove yet more unused functions
wifi: brcm80211: Remove more unused functions
wifi: brcm80211: Remove unused functions
wifi: iwlwifi: Revert "wifi: iwlwifi: remove support of several iwl_ppag_table_cmd versions"
wifi: iwlwifi: check validity of the FW API range
wifi: iwlwifi: don't export symbols that we shouldn't
wifi: iwlwifi: mld: use spec link id and not FW link id
wifi: iwlwifi: mld: decode EOF bit for AMPDUs
wifi: iwlwifi: Remove support for rx OMI bandwidth reduction
wifi: iwlwifi: stop supporting iwl_omi_send_status_notif ver 1
wifi: iwlwifi: remove SC2F firmware support
wifi: iwlwifi: mvm: Remove NAN support
wifi: iwlwifi: mld: avoid outdated reorder buffer head_sn
wifi: iwlwifi: mvm: avoid outdated reorder buffer head_sn
wifi: iwlwifi: disable certain features for fips_enabled
wifi: iwlwifi: mld: support channel survey collection for ACS scans
...
====================
Link: https://patch.msgid.link/20250724100349.21564-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.16-rc8).
Conflicts:
drivers/net/ethernet/microsoft/mana/gdma_main.c
9669ddda18fb ("net: mana: Fix warnings for missing export.h header inclusion")
755391121038 ("net: mana: Allocate MSI-X vectors dynamically")
https://lore.kernel.org/20250711130752.23023d98@canb.auug.org.au
Adjacent changes:
drivers/net/ethernet/ti/icssg/icssg_prueth.h
6e86fb73de0f ("net: ti: icssg-prueth: Fix buffer allocation for ICSSG")
ffe8a4909176 ("net: ti: icssg-prueth: Read firmware-names from device tree")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is no need to store the err string in hw->err_str. Simplify it and
use common helper. hw->err_str is still used for other purpouse.
It should be marked that previously for unknown error the numeric value
was passed as a string. Now the "LIBIE_AQ_RC_UNKNOWN" is used for such
cases.
Add libie_aminq module in i40e Kconfig.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is no need to store the err string in hw->err_str. Simplify it and
use common helper. hw->err_str is still used for other purpouse.
It should be marked that previously for unknown error the numeric value
was passed as a string. Now the "LIBIE_AQ_RC_UNKNOWN" is used for such
cases.
Add libie_aminq module in iavf Kconfig.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Simple:
s/ice_aq_str/libie_aq_str
Add libie_aminq module in ice Kconfig.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a new module for common handling of Admin Queue related logic.
Start by a helper for error to string conversion. This lives inside
libie/, but is a separate module what follows our logic of splitting
into topical modules, to avoid pulling in not needed stuff, and have
better organization in general.
Olek suggested how to better solve the error to string conversion.
It will be used in follow-up patches in ice, i40e and iavf.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
