| Age | Commit message (Collapse) | Author |
|---|
|
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The commit 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc385e ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.5-rc7
Here are a few fixes for issues related to unbound port devices which
could lead to NULL-pointer dereferences. Notably the bind attributes for
usb-serial (port) drivers are removed as almost none of the drivers can
handle individual ports going away once they've been bound.
Included are also some new device ids.
All but the unbound-port fixes have been in linux-next with no reported
issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-5.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: quatech2: handle unbound ports
USB: serial: keyspan: handle unbound ports
USB: serial: io_edgeport: add missing active-port sanity check
USB: serial: io_edgeport: handle unbound ports on URB completion
USB: serial: ch341: handle unbound port at reset_resume
USB: serial: suppress driver bind attributes
USB: serial: option: add support for Quectel RM500Q in QDL mode
USB: serial: opticon: fix control-message timeouts
USB: serial: option: Add support for Quectel RM500Q
USB: serial: simple: Add Motorola Solutions TETRA MTP3xxx and MTP85xx
|
|
The hwmon core uses device managed functions, tied to the hwmon parent
device, for various internal memory allocations. This is problematic
since hwmon device lifetime does not necessarily match its parent's
device lifetime. If there is a mismatch, memory leaks will accumulate
until the parent device is released.
Fix the problem by managing all memory allocations internally. The only
exception is memory allocation for thermal device registration, which
can be tied to the hwmon device, along with thermal device registration
itself.
Fixes: d560168b5d0f ("hwmon: (core) New hwmon registration API")
Cc: stable@vger.kernel.org # v4.14.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.14.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9.x: 3a412d5e4a1c: hwmon: (core) Simplify sysfs attribute name allocation
Cc: stable@vger.kernel.org # v4.9.x: 47c332deb8e8: hwmon: Deal with errors from the thermal subsystem
Cc: stable@vger.kernel.org # v4.9.x: 74e3512731bd: hwmon: (core) Fix double-free in __hwmon_device_register()
Cc: stable@vger.kernel.org # v4.9+
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191205231659.1301-1-luuk.paulussen@alliedtelesis.co.nz
cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
No alarm is reported by /sys/.../inX_alarm
In detail:
The SMI Voltage status register is the only register giving a status
for voltages, but it does not work like the non-SMI status registers
used for temperatures and fans.
A bit is set for each input crossing a threshold, in both direction,
but the "inside" or "outside" limits info is not available.
Also this register is cleared on read.
Note : this is not explicitly spelled out in the datasheet, but from
experiment.
As a result if an input is crossing a threshold (min or max in any
direction), the alarm is reported only once even if the input is
still outside limits. Also if the alarm for another input is read
before the one of this input, no alarm is reported at all.
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f566.tBga5POKAgHlmd0p%gilles.buloz@kontron.com
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
in0 thresholds are written to the in2 thresholds registers
in2 thresholds to in3 thresholds
in3 thresholds to in4 thresholds
in4 thresholds to in0 thresholds
Signed-off-by: Gilles Buloz <gilles.buloz@kontron.com>
Link: https://lore.kernel.org/r/5de0f509.rc0oEvPOMjbfPW1w%gilles.buloz@kontron.com
Fixes: 3434f3783580 ("hwmon: Driver for Nuvoton NCT7802Y")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org> # 3.5
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e109a ("USB Serial Keyspan: add support for USA-49WG & USA-28XG")
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"This reverts the GPIOLIB_IRQCHIP in the ThunderX driver.
ThunderX is a piece of Arm-based server chip. I converted the driver
to hierarchical gpiochip without access to real silicon and failed
miserably since I didn't take MSI's into account.
Kevin Hao helpfully stepped in and fixed it properly, let's revert it
for v5.5 and put the proper conversion into v5.6"
* tag 'gpio-v5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
Revert "gpio: thunderx: Switch to GPIOLIB_IRQCHIP"
|
|
Pull block fixes from Jens Axboe:
"Three fixes that should go into this release:
- The 32-bit segment size fix that I mentioned last week (Ming)
- Use uint for the block size (Mikulas)
- A null_blk zone write handling fix (Damien)"
* tag 'block-5.5-2020-01-16' of git://git.kernel.dk/linux-block:
block: fix an integer overflow in logical block size
null_blk: Fix zone write handling
block: fix get_max_segment_size() overflow on 32bit arch
|
|
The IORT specification [0] (Section 3, table 4, page 9) defines the
'Number of IDs' as 'The number of IDs in the range minus one'.
However, the IORT ID mapping function iort_id_map() treats the 'Number
of IDs' field as if it were the full IDs mapping count, with the
following check in place to detect out of boundary input IDs:
InputID >= Input base + Number of IDs
This check is flawed in that it considers the 'Number of IDs' field as
the full number of IDs mapping and disregards the 'minus one' from
the IDs count.
The correct check in iort_id_map() should be implemented as:
InputID > Input base + Number of IDs
this implements the specification correctly but unfortunately it breaks
existing firmwares that erroneously set the 'Number of IDs' as the full
IDs mapping count rather than IDs mapping count minus one.
e.g.
PCI hostbridge mapping entry 1:
Input base: 0x1000
ID Count: 0x100
Output base: 0x1000
Output reference: 0xC4 //ITS reference
PCI hostbridge mapping entry 2:
Input base: 0x1100
ID Count: 0x100
Output base: 0x2000
Output reference: 0xD4 //ITS reference
Two mapping entries which the second entry's Input base = the first
entry's Input base + ID count, so for InputID 0x1100 and with the
correct InputID check in place in iort_id_map() the kernel would map
the InputID to ITS 0xC4 not 0xD4 as it would be expected.
Therefore, to keep supporting existing flawed firmwares, introduce a
workaround that instructs the kernel to use the old InputID range check
logic in iort_id_map(), so that we can support both firmwares written
with the flawed 'Number of IDs' logic and the correct one as defined in
the specifications.
[0]: http://infocenter.arm.com/help/topic/com.arm.doc.den0049d/DEN0049D_IO_Remapping_Table.pdf
Reported-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Link: https://lore.kernel.org/linux-acpi/20191215203303.29811-1-pankaj.bansal@nxp.com/
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Pankaj Bansal <pankaj.bansal@nxp.com>
Cc: Will Deacon <will@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c440704661 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the implementation of the system reset controller we lost a setting
that is currently applied by the bootloader and which configures the IMP
port for 2Gb/sec, the default is 1Gb/sec. This is needed given the
number of ports and applications we expect to run so bring back that
setting.
Fixes: 01b0ac07589e ("net: dsa: bcm_sf2: Add support for optional reset controller line")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sja1105_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.
Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On machines which do not populate all nodes with DIMMs, the driver
doesn't initialize an instance there. However, the instance removal
remove_one_instance() path will warn unconditionally, which is wrong.
Remove the WARN_ON() even if the warning is innocent because it causes a
splat in dmesg.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200117115939.5524-1-bp@alien8.de
|
|
According to the Datasheet this bit should be 0 (Normal operation) in
default. With the FORCE_LINK_GOOD bit set, it is not possible to get a
link. This patch sets FORCE_LINK_GOOD to the default value after
resetting the phy.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a36 ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea54 ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.5-3
* Fix Interrupt Status register offset for Intel Sunrisepoint PCH-H.
The following is an automated git shortlog grouped by driver:
sunrisepoint:
- Add missing Interrupt Status register offset
|
|
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9ac9 ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This reverts commit a284e11c371e446371675668d8c8120a27227339.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c371e ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Second collection of clk fixes for the next release.
This one includes a fix for PM on TI SoCs with sysc devices and fixes
a bunch of clks that are stuck always enabled on Qualcomm SDM845 SoCs.
Allwinner SoCs get the usual set of fixes too, mostly correcting
drivers to have the right bits that match the hardware.
There's also a Samsung and Tegra fix in here to mark a clk critical
and avoid a double free.
And finally there's a fix for critical clks that silences a big
warning splat about trying to enable a clk that couldn't even be
prepared"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dra7-atl: Remove pm_runtime_irq_safe()
clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: Don't try to enable critical clocks if prepare failed
clk: tegra: Fix double-free in tegra_clk_init()
clk: samsung: exynos5420: Keep top G3D clocks enabled
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
|
|
In case of error, the function edac_device_alloc_ctl_info() returns a
NULL pointer, not ERR_PTR(). Replace the IS_ERR() test in the return
value check with a NULL test.
Fixes: 91abaeaaff35 ("EDAC/sifive: Add EDAC platform driver for SiFive SoCs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200115150303.112627-1-weiyongjun1@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a coding mistake in the teo cpuidle governor causing data to be
written beyond the last array element (Ikjoon Jang)"
* tag 'pm-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Fix intervals[] array indexing bug
|
|
... and do not kmalloc a three-pointer struct. Which simplifies
mce_amd_init() a bit.
No functional changes.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200116163403.GF27148@zn.tnic
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform fix from Benson Leung:
"One fix in the wilco_ec keyboard backlight driver to allow the EC
driver to continue loading in the absence of a backlight module"
* tag 'tag-chrome-platform-fixes-for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: Fix keyboard backlight probing
|
|
In general, "pvt->umc != NULL" is used to check if the system is Family
17h+. However, there are a few places that are using direct family
checks.
Replace the remaining family checks with a check for "pvt->umc != NULL".
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200110015651.14887-6-Yazen.Ghannam@amd.com
|
|
Add family ops to support AMD Family 19h systems. Existing Family 17h
functions can be used. Also, add Family 19h to the list of families to
automatically load the module.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200110015651.14887-5-Yazen.Ghannam@amd.com
|
|
MCA error decoding on SMCA systems is not dependent on family. Return
success early if the system supports the SMCA feature.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200110015651.14887-3-Yazen.Ghannam@amd.com
|
|
Add support for a new version of the Load Store unit bank type as
indicated by its McaType value, which will be present in future SMCA
systems.
Add the new (HWID, MCATYPE) tuple. Reuse the same name, since this is
logically the same to the user.
Also, add the new error descriptions to edac_mce_amd.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200110015651.14887-2-Yazen.Ghannam@amd.com
|
|
Add support for Quectel RM500Q in QDL mode.
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 24 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0800 Rev= 0.00
S: Manufacturer=Qualcomm CDMA Technologies MSM
S: Product=QUSB_BULK_SN:xxxxxxxx
S: SerialNumber=xxxxxxxx
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=10 Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
It is assumed that the ZLP flag required for other Qualcomm-based
5G devices also applies to Quectel RM500Q.
Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Commit 7ad2ed1dfcbe inadvertently mixed up a quirk flag's name and
broke SDR50 tuning override. Use correct NVQUIRK_ name.
Fixes: 7ad2ed1dfcbe ("mmc: tegra: enable UHS-I modes")
Cc: <stable@vger.kernel.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/9aff1d859935e59edd81e4939e40d6c55e0b55f6.1578390388.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The only callers of the function lapbeth_get_x25_dev()
are lapbeth_rcv() and lapbeth_device_event().
lapbeth_rcv() uses rcu_read_lock() whereas lapbeth_device_event()
is called with RTNL held (As mentioned in the comments).
Therefore, pass lockdep_rtnl_is_held() as cond argument in
list_for_each_entry_rcu();
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik04@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9e2 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jurgen Van Ham <juvanham@gmail.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sdhci_alloc_host() does its work not using managed infrastructure, so
needs explicit free on error path. Add it where needed.
Cc: <stable@vger.kernel.org>
Fixes: bb5f8ea4d514 ("mmc: sdhci-of-at91: introduce driver for the Atmel SDMMC")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/b2a44d5be2e06ff075f32477e466598bb0f07b36.1577961679.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.
Fixes: f545702b74f9 ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.
Fixes: 41fd4caeb00b ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.
Fixes: 1accbced1c32 ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
