| Age | Commit message (Collapse) | Author |
|---|
|
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Current code set incorrect bits when set ramp_delay for AXP20X_DCDC2,
fix it.
Fixes: d29f54df8b16 ("regulator: axp20x: add support for set_ramp_delay for AXP209")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20191221081049.32490-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit:
0d95981438c3 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table")
causes the drivers/efi/libstub/random.c code to get used on x86 for the first time.
But this code was not written with EFI mixed mode in mind (running a 64
bit kernel on 32 bit EFI firmware), this causes the kernel to crash during
early boot when running in mixed mode.
The problem is that in mixed mode pointers are 64 bit, but when running on
a 32 bit firmware, EFI calls which return a pointer value by reference only
fill the lower 32 bits of the passed pointer, leaving the upper 32 bits
uninitialized which leads to crashes.
This commit fixes this by initializing pointers which are passed by
reference to EFI calls to NULL before passing them, so that the upper 32
bits are initialized to 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 0d95981438c3 ("x86: efi/random: Invoke EFI_RNG_PROTOCOL to seed the UEFI RNG table")
Link: https://lkml.kernel.org/r/20191224132909.102540-3-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
On x86, until PAT is initialized, WC translates into UC-. Since we
calculate and store pgprot_writecombine(PAGE_KERNEL) when earlycon is
initialized, this means we actually use UC- mappings instead of WC
mappings, which makes scrolling very slow.
Instead store a boolean flag to indicate whether we want to use
writeback or write-combine mappings, and recalculate the actual pgprot_t
we need on every mapping. Once PAT is initialized, we will start using
write-combine mappings, which speeds up the scrolling considerably.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 69c1f396f25b ("efi/x86: Convert x86 EFI earlyprintk into generic earlycon implementation")
Link: https://lkml.kernel.org/r/20191224132909.102540-2-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d40831d ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx threshold means the value to inform the receiver when the number of words
in Rx FIFO is equal to or more than the value. Similarly, Tx threshold means
the value to inform the sender when the number of words in Tx FIFO is equal
to or less than the value. The controller triggers the driver to start
the transfer.
In case of Rx, the driver wants to detect that the specified number of words
N are in Rx FIFO, so the value of Rx threshold should be N. In case of Tx,
the driver wants to detect that the same number of spaces as Rx are in
Tx FIFO, so the value of Tx threshold should be (FIFO size - N).
For example, in order for the driver to receive at least 3 words from
Rx FIFO, set 3 to Rx threshold.
+-+-+-+-+-+-+-+-+
| | | | | |*|*|*|
+-+-+-+-+-+-+-+-+
In order for the driver to send at least 3 words to Tx FIFO, because
it needs at least 3 spaces, set 8(FIFO size) - 3 = 5 to Tx threshold.
+-+-+-+-+-+-+-+-+
|*|*|*|*|*| | | |
+-+-+-+-+-+-+-+-+
This adds new function uniphier_spi_set_fifo_threshold() to set
threshold value to the register.
And more, FIFO counts by 'words', so this renames 'fill_bytes' with
'fill_words', and fixes the calculation using bytes_per_words.
Fixes: 37ffab817098 ("spi: uniphier: introduce polling mode")
Cc: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1577149107-30670-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's unlikely to happen in practice ever, but makes static checkers happy.
Fixes: 535f296d47de ("clk: tegra: Add suspend and resume support on Tegra210")
Reported-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lkml.kernel.org/r/20191210020512.6088-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In Exynos542x/5800 SoCs, the G3D leaf clocks are located in the G3D power
domain. This is similar to the other hardware modules and their power
domains. However there is one thing specific to G3D clocks hierarchy.
Unlike other hardware modules, the G3D clocks hierarchy doesn't have any
gate clock between the TOP part of the hierarchy and the part located in
the power domain and some SoC internal busses are sourced directly from
the TOP muxes. The consequence of this design if the fact that the TOP
part of the hierarchy has to be enabled permanently to ensure proper
operation of the SoC power related components (G3D power domain and
Exynos Power Management Unit for system suspend/resume).
This patch adds an explicit call to clk_prepare_enable() on the last MUX
in the TOP part of G3D clock hierarchy to keep it enabled permanently to
ensure that the internal busses get their clock regardless of the main
G3D clock enablement status.
This fixes following imprecise abort issue observed on Odroid XU3/XU4
after enabling Panfrost driver by commit 1a5a85c56402 "ARM: dts: exynos:
Add Mali/GPU node on Exynos5420 and enable it on Odroid XU3/4"):
panfrost 11800000.gpu: clock rate = 400000000
panfrost 11800000.gpu: failed to get regulator: -517
panfrost 11800000.gpu: regulator init failed -517
Power domain G3D disable failed
...
panfrost 11800000.gpu: clock rate = 400000000
8<--- cut here ---
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: : 1406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 7 PID: 53 Comm: kworker/7:1 Not tainted 5.4.0-rc8-next-20191119-00032-g56f1001191a6 #6923
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at panfrost_gpu_soft_reset+0x94/0x110
LR is at ___might_sleep+0x128/0x2dc
...
[<c05c231c>] (panfrost_gpu_soft_reset) from [<c05c2704>] (panfrost_gpu_init+0x10/0x67c)
[<c05c2704>] (panfrost_gpu_init) from [<c05c15d0>] (panfrost_device_init+0x158/0x2cc)
[<c05c15d0>] (panfrost_device_init) from [<c05c0cb0>] (panfrost_probe+0x80/0x178)
[<c05c0cb0>] (panfrost_probe) from [<c05cfaa0>] (platform_drv_probe+0x48/0x9c)
[<c05cfaa0>] (platform_drv_probe) from [<c05cd20c>] (really_probe+0x1c4/0x474)
[<c05cd20c>] (really_probe) from [<c05cd694>] (driver_probe_device+0x78/0x1bc)
[<c05cd694>] (driver_probe_device) from [<c05cb374>] (bus_for_each_drv+0x74/0xb8)
[<c05cb374>] (bus_for_each_drv) from [<c05ccfa8>] (__device_attach+0xd4/0x16c)
[<c05ccfa8>] (__device_attach) from [<c05cc110>] (bus_probe_device+0x88/0x90)
[<c05cc110>] (bus_probe_device) from [<c05cc634>] (deferred_probe_work_func+0x4c/0xd0)
[<c05cc634>] (deferred_probe_work_func) from [<c0149df0>] (process_one_work+0x300/0x864)
[<c0149df0>] (process_one_work) from [<c014a3ac>] (worker_thread+0x58/0x5a0)
[<c014a3ac>] (worker_thread) from [<c0151174>] (kthread+0x12c/0x160)
[<c0151174>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xee03dfb0 to 0xee03dff8)
...
Code: e594300c e5933020 e3130c01 1a00000f (ebefff50).
---[ end trace badde2b74a65a540 ]---
In the above case, the Panfrost driver disables G3D clocks after failure
of getting the needed regulator and return with -EPROVE_DEFER code. This
causes G3D power domain disable failure and then, during second probe
an imprecise abort is triggered due to undefined power domain state.
Fixes: 45f10dabb56b ("clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path")
Fixes: c9f7567aff31 ("clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lkml.kernel.org/r/20191216131407.17225-1-m.szyprowski@samsung.com
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In the for loop where we are supposed to go through the entire table,
we are using a non-static local to keep the pos index. This makes
each iteration start with 3, so we always access the first item on the
table. Fix this by moving the variable outside of the loo so it
doesn't lose its value at every iteration.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: ba3224db7803 ("iwlwifi: mvm: fix an out-of-bound access")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This is an old parameter that was used supposed to be used only when
LAR was still under development. It should not be used anymore, but,
since it's available, end-users have been mangling with it
unnecessarily. In some cases it can cause problems because when LAR
is supported the driver and the firmware do not expect it to be
disabled.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The driver is required to stop the debug monitor HW recording regardless
of the debug configuration since the driver is responsible to halt the
FW DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
L0S states have been found to be unstable with our devices and in
newer hardware they are not supported at all, so we must always set
the L0S_DISABLED bit. Previously we were only disabling L0S states if
L1 was supported, because the assumption was that transitions from L0S
to L1 state was the problematic case. But now we should never use
L0S, so do it regardless of whether L1 is supported or not.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This bit has been misnamed since the initial implementation of the
driver. The correct semantics is that setting this bit disables L0S
states, and we already clearly use it as such in the code. Rename it
to avoid confusion.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b91 ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b91 ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since obj->frontbuffer is no longer protected by the struct_mutex, as we
are processing the execbuf, it may be removed. Mark the
intel_frontbuffer as rcu protected, and so acquire a reference to
the struct as we track activity upon it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/827
Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk
(cherry picked from commit da42104f589d979bbe402703fd836cec60befae1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
For very light workloads that frequently park, acquiring the display
power well (required to prevent the dmc from trashing the system) takes
longer than the execution. A good example is the igt_coherency selftest,
which is slowed down by an order of magnitude in the worst case with
powerwell cycling. To prevent frequent cycling, while keeping our fast
soft-rc6, use a timer to delay release of the display powerwell.
Fixes: 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles")
References: https://gitlab.freedesktop.org/drm/intel/issues/848
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218093504.3477048-1-chris@chris-wilson.co.uk
(cherry picked from commit 81ff52b705775433a955b2746d37b87bdc89a3d0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Avoid rc6 counter going backward in close to 0% RC6 scenarios like:
15.005477996 114,246,613 ns i915/rc6-residency/
16.005876662 667,657 ns i915/rc6-residency/
17.006131417 7,286 ns i915/rc6-residency/
18.006615031 18,446,744,073,708,914,688 ns i915/rc6-residency/
19.007158361 18,446,744,073,709,447,168 ns i915/rc6-residency/
20.007806498 0 ns i915/rc6-residency/
21.008227495 1,440,403 ns i915/rc6-residency/
There are two aspects to this fix.
First is not assuming rc6 value zero means GT is asleep since that can
also mean GPU is fully busy and we do not want to enter the estimation
path in that case.
Second is ensuring monotonicity on the estimation path itself. I suspect
what is happening is with extremely rapid park/unpark cycles we get no
updates on the real rc6 and therefore have to careful not to
unconditionally trust use last known real rc6 when creating a new
estimation.
v2:
* Simplify logic by not tracking the estimate but last reported value.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 16ffe73c186b ("drm/i915/pmu: Use GT parked for estimating RC6 while asleep")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217142057.1000-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit df6a42053513846475ae1fbd224dfbdbcd0c7010)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
After more investigation on the hardware side, it appears that the
hardware bug regarding 2^32 boundary reaching/crossing also affects
other uses of the DMA engine, in particular the ones triggered by
the context-info (image loader) mechanism.
It also turns out that the bug only affects devices with gen2 TX
hardware engine, so we don't need to change context info for gen3.
The TX path workarounds are simpler to still keep for both though.
Add the workaround to that code as well; this is a lot simpler as
we have just a single way to allocate DMA memory there.
I made the algorithm recursive (with a small limit) since it's
actually (almost) impossible to hit this today - dma_alloc_coherent
is currently documented to always return 32-bit addressable memory
regardless of the DMA mask for it, and so we could only get REALLY
unlucky to get the very last page in that area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we have offloaded rate scaling, which is always true for those
devices supporting HE, then report the TX rate directly from the
data the firmware gives us, instead of only passing it to mac80211
on frame status only and for it to track it.
First of all, this makes us always report the last good rate that
the rate scaling algorithm picked, which is better than reporting
the last rate for any frame since management frames etc. are sent
with very low rates and could interfere.
Additionally, this allows us to properly report HE rates, though
in case there's a lot of trigger-based traffic, we don't get any
choice in the rates and don't report that properly right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We had a check on !NVM_EXT and then a check for NVM_SDP in the else
block of this if. The else block, obviously, could only be reached if
using NVM_EXT, so it would never be NVM_SDP.
Fix that by checking whether the nvm_type is IWL_NVM instead of
checking for !IWL_NVM_EXT to solve this issue.
Reported-by: Stefan Sperling <stsp@stsp.name>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In the allocation loop, "pages" will never become zero (because of the
DIV_ROUND_UP), so if we can't allocate any size and pages becomes 1,
we will keep trying to allocate 1 page until it succeeds. And in that
case, as coverity reported, block will never be NULL.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1487402 ("Control flow issues")
Fixes: 14124b25780d ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 14124b25780d ("iwlwifi: dbg_ini: implement monitor allocation flow")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Warn if the DMA bug is going to happen. We don't have a good
way of actually aborting in this case and we have workarounds
in place for the cases where it happens, but in order to not
be surprised add a safety-check and warn.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's a hardware bug in the flow handler (DMA engine), if the
address + len of some TB wraps around a 2^32 boundary, the carry
bit is then carried over into the next TB.
Work around this by copying the data to a new page when we find
this situation, and then copy it in a way that we cannot hit the
very end of the page.
To be able to free the new page again later we need to chain it
to the TSO page, use the last pointer there to make sure we can
never use the page fully for DMA, and thus cannot cause the same
overflow situation on this page.
This leaves a few potential places (where we didn't observe the
problem) unaddressed:
* The second TB could reach or cross the end of a page (and thus
2^32) due to the way we allocate the dev_cmd for the header
* For host commands, a similar thing could happen since they're
just kmalloc().
We'll address these in further commits.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
vchan_vdesc_fini() is freeing up 'vd' so the access to vd->tx_result is
via already freed up memory.
Move the vchan_vdesc_fini() after invoking the callback to avoid this.
Fixes: 09d5b702b0f97 ("dmaengine: virt-dma: store result on dma descriptor")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191220131100.21804-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In some cases we seem to submit two transactions in a row, which
causes us to lose track of the first. If we then cancel the
request, we may still get an interrupt, which traverses a null
ds_run value.
So try to avoid starting a new transaction if the ds_run value
is set.
While this patch avoids the null pointer crash, I've had some
reports of the k3dma driver still getting confused, which
suggests the ds_run/ds_done value handling still isn't quite
right. However, I've not run into an issue recently with it
so I think this patch is worth pushing upstream to avoid the
crash.
Signed-off-by: John Stultz <john.stultz@linaro.org>
[add ss tag]
Link: https://lore.kernel.org/r/20191218190906.6641-1-john.stultz@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Compile-testing this driver fails if CONFIG_COMMON_CLK is not set:
drivers/devfreq/tegra30-devfreq.o: In function `tegra_devfreq_target':
tegra30-devfreq.c:(.text+0x164): undefined reference to `clk_set_min_rate'
Fixes: 35f8dbc72721 ("PM / devfreq: tegra: Enable COMPILE_TEST for the driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
CONFIG_PM_OPP is already selected by CONFIG_PM_DEVFREQ
since commit b9c69e043266 ("PM / devfreq: Add dependency on PM_OPP").
This means that individual drivers shouldn't "select PM_OPP" explicitly.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
[cw00.choi: Edit the patch title]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Pull block fixes from Jens Axboe:
"Let's try this one again, this time without the compat_ioctl changes.
We've got those fixed up, but that can go out next week.
This contains:
- block queue flush lockdep annotation (Bart)
- Type fix for bsg_queue_rq() (Bart)
- Three dasd fixes (Stefan, Jan)
- nbd deadlock fix (Mike)
- Error handling bio user map fix (Yang)
- iocost fix (Tejun)
- sbitmap waitqueue addition fix that affects the kyber IO scheduler
(David)"
* tag 'block-5.5-20191221' of git://git.kernel.dk/linux-block:
sbitmap: only queue kyber's wait callback if not already active
block: fix memleak when __blk_rq_map_user_iov() is failed
s390/dasd: fix typo in copyright statement
s390/dasd: fix memleak in path handling error case
s390/dasd/cio: Interpret ccw_device_get_mdc return value correctly
block: Fix a lockdep complaint triggered by request queue flushing
block: Fix the type of 'sts' in bsg_queue_rq()
block: end bio with BLK_STS_AGAIN in case of non-mq devs and REQ_NOWAIT
nbd: fix shutdown and recv work deadlock v2
iocost: over-budget forced IOs should schedule async delay
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Several fixes, and one cleanup, for RISC-V.
Fixes:
- Fix an error in a Kconfig file that resulted in an undefined
Kconfig option "CONFIG_CONFIG_MMU"
- Fix undefined Kconfig option "CONFIG_CONFIG_MMU"
- Fix scratch register clearing in M-mode (affects nommu users)
- Fix a mismerge on my part that broke the build for
CONFIG_SPARSEMEM_VMEMMAP users
Cleanup:
- Move SiFive L2 cache-related code to drivers/soc, per request"
* tag 'riscv/for-v5.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: move sifive_l2_cache.c to drivers/soc
riscv: define vmemmap before pfn_to_page calls
riscv: fix scratch register clearing in M-mode.
riscv: Fix use of undefined config option CONFIG_CONFIG_MMU
|
|
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
|
|
The support for the compat ioctl did not actually do what it was
supposed to do because of a typo, instead it broke native support for
CDROM_LAST_WRITTEN and CDROM_SEND_PACKET on all architectures with
CONFIG_COMPAT enabled.
Fixes: 1b114b0817cc ("pktcdvd: add compat_ioctl handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
Please apply for v5.5, I just noticed the regression while
rebasing some of the patches I created on top.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains two cleanup patches and a small series for supporting
reloading the Xen block backend driver"
* tag 'for-linus-5.5b-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grant-table: remove multiple BUG_ON on gnttab_interface
xen-blkback: support dynamic unbind/bind
xen/interface: re-define FRONT/BACK_RING_ATTACH()
xenbus: limit when state is forced to closed
xenbus: move xenbus_dev_shutdown() into frontend code...
xen/blkfront: Adjust indentation in xlvbd_alloc_gendisk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two weeks worth of accumulated fixes:
- A fix for a performance regression seen on PowerVM LPARs using
dedicated CPUs, caused by our vcpu_is_preempted() returning true
even for idle CPUs.
- One of the ultravisor support patches broke KVM on big endian hosts
in v5.4.
- Our KUAP (Kernel User Access Prevention) code missed allowing
access in __clear_user(), which could lead to an oops or erroneous
SEGV when triggered via PTRACE_GETREGSET.
- Two fixes for the ocxl driver, an open/remove race, and a memory
leak in an error path.
- A handful of other small fixes.
Thanks to: Andrew Donnellan, Christian Zigotzky, Christophe Leroy,
Christoph Hellwig, Daniel Axtens, David Hildenbrand, Frederic Barrat,
Gautham R. Shenoy, Greg Kurz, Ihor Pasichnyk, Juri Lelli, Marcus
Comstedt, Mike Rapoport, Parth Shah, Srikar Dronamraju, Vaidyanathan
Srinivasan"
* tag 'powerpc-5.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S HV: Fix regression on big endian hosts
powerpc: Fix __clear_user() with KUAP enabled
powerpc/pseries/cmm: fix managed page counts when migrating pages between zones
powerpc/8xx: fix bogus __init on mmu_mapin_ram_chunk()
ocxl: Fix potential memory leak on context creation
powerpc/irq: fix stack overflow verification
powerpc: Ensure that swiotlb buffer is allocated from low memory
powerpc/shared: Use static key to detect shared processor
powerpc/vcpu: Assume dedicated processors as non-preempt
ocxl: Fix concurrent AFU open and device removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One core framework fix to walk the orphan list and match up clks to
parents when clk providers register the DT provider after registering
all their clks (as they should).
Then a handful of driver fixes for the qcom, imx, and at91 drivers.
The driver fixes are relatively small fixes for incorrect register
settings or missing locks causing race conditions"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: qcom: Avoid SMMU/cx gdsc corner cases
clk: qcom: gcc-sc7180: Fix setting flag for votable GDSCs
clk: Move clk_core_reparent_orphans() under CONFIG_OF
clk: at91: fix possible deadlock
clk: walk orphan list on clock provider registration
clk: imx: pll14xx: fix clk_pll14xx_wait_lock
clk: imx: clk-imx7ulp: Add missing sentinel of ulp_div_table
clk: imx: clk-composite-8m: add lock to gate/mux
|
|
Correct a mismatch between rx_page_buf_step and the actual step size
used when filling buffer pages.
This patch fixes the page overrun that occured when the MTU was set to
anything bigger than 1692.
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues")
Signed-off-by: Charles McLachlan <cmclachlan@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
