| Age | Commit message (Collapse) | Author |
|---|
|
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
How to reproduce this bug ?
-----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24 \--|-- eth1-/ |
--------------------------------
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a regulator with a supply is being unregistered we will call
regulator_put() to release the supply with the regulator_list_mutex held
but this deadlocks as regulator_put() takes the same lock. Fix this by
releasing the supply before we take the mutex in regulator_unregister().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer core updates from Thomas Gleixner.
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ia64: vsyscall: Add missing paranthesis
alarmtimer: Don't call rtc_timer_init() when CONFIG_RTC_CLASS=n
x86: vdso: Put declaration before code
x86-64: Inline vdso clock_gettime helpers
x86-64: Simplify and optimize vdso clock_gettime monotonic variants
kernel-time: fix s/then/than/ spelling errors
time: remove no_sync_cmos_clock
time: Avoid scary backtraces when warning of > 11% adj
alarmtimer: Make sure we initialize the rtctimer
ntp: Fix leap-second hrtimer livelock
x86, tsc: Skip refined tsc calibration on systems with reliable TSC
rtc: Provide flag for rtc devices that don't support UIE
ia64: vsyscall: Use seqcount instead of seqlock
x86: vdso: Use seqcount instead of seqlock
x86: vdso: Remove bogus locking in update_vsyscall_tz()
time: Remove bogus comments
time: Fix change_clocksource locking
time: x86: Fix race switching from vsyscall to non-vsyscall clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"This contains the updated gpio_to_irq patches from Tarun, and a trivial
build fix from Govindraj to #include <asm/system_misc.h> in pm.c.
The DSI mux patch is the same."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: pm: fix compilation break
ARM: OMAP: Remove OMAP_GPIO_IRQ macro definition
drivers: input: Fix OMAP_GPIO_IRQ with gpio_to_irq() in ams_delta_serio_exit()
ARM: OMAP: boards: Fix OMAP_GPIO_IRQ usage with gpio_to_irq()
ARM: OMAP2+: Remove __init from DSI mux functions
|
|
Pull the intel i915 hibernation memory corruption fix from Dave Airlie:
"I tracked down the misc memory corruption after i915 hibernate to the
blinking fbcon cursor, and realised the i915 driver wasn't doing the
fbdev suspend/resume calls at all. nouveau and radeon have done these
calls for a long time.
This has been fairly well tested and is definitely the main culprit in
hibernate not working."
Yay.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: suspend fbdev device around suspend/hibernate
|
|
Conflicts:
arch/arm/mach-omap1/board-htcherald.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/plat-omap/include/plat/gpio.h
drivers/input/serio/ams_delta_serio.c
|
|
Even though ams-delta-serio input driver uses gpio_to_irq() in all
relevent places to get irq number, the ams_delta_serio_exit() still
uses OMAP_GPIO_IRQ macro. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This reverts commit a81f15499887d3f9f24ec70bb9b7e778942a6b7b.
Gah, we have a released userspace component using fixed subc assignment
that conflicts with this. To avoid breaking ABI this needs to be
reverted.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
wm8350_[ldo|dcdc]_set_suspend_disable
What we want is to disable output by setting [LDOx|DCx]_HIB_MODE bits.
Current code also clears other bits in LDOx/DCDCx Low Power register.
R202 (CAh) LDO1 Low Power
BIT[13:12] LDO1 Hibernate behaviour:
00 = Select voltage image settings
01 = disable output
10 = reserved
11 = reserved
R182 (B6h) DCDC1 Low Power
BIT[14:12] DC-DC1 Hibernate behaviour:
000 = Use current settings (no change)
001 = Select voltage image settings
010 = Force standby mode
011 = Force standby mode and voltage image settings.
100 = Force LDO mode
101 = Force LDO mode and voltage image settings.
110 = Reserved.
111 = Disable output
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Set BIT[8] of LDO7 ON Control mode for low power mode.
R16507 (407Bh) LDO7 ON Control
BIT[8] LDO7_ON_MODE: LDO7 ON Operating Mode
0 = Normal mode
1 = Low Power mode
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
I was trying to backport the following commit to RHEL-6
From 0cea73465cd22373c5cd43a3edd25fbd4bb532ef Mon Sep 17 00:00:00 2001
From: Oliver Neukum <oliver@neukum.org>
Date: Wed, 21 Sep 2011 11:37:15 +0200
Subject: [PATCH] btusb: add device entry for Broadcom SoftSailing
and noticed it wasn't working on an HP Elitebook. Looking into the patch I
noticed a very subtle typo in the ids. The patch has '0x05ac' instead of
'0x0a5c'. A snippet of the lsusb -v output also shows this:
Bus 002 Device 003: ID 0a5c:21e1 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a5c Broadcom Corp.
idProduct 0x21e1
bcdDevice 1.12
iManufacturer 1 Broadcom Corp
iProduct 2 BCM20702A0
iSerial 3 60D819F0338C
bNumConfigurations 1
Looking at other Broadcom ids, the fix matches them whereas the original patch
matches Apple's ids.
Tested on an HP Elitebook 8760w. The btusb binds and the userspace stuff loads
correctly.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
If a virtio disk is open in guest and a disk resize operation is done,
(virsh blockresize), new size is not visible to tools like "fdisk -l".
This seems to be happening as we update only part->nr_sects and not
bdev->bd_inode size.
Call revalidate_disk() which should take care of it. I tested growing disk
size of already open disk and it works for me.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Looking at hibernate overwriting I though it looked like a cursor,
so I tracked down this missing piece to stop the cursor blink
timer. I've no idea if this is sufficient to fix the hibernate
problems people are seeing, but please test it.
Both radeon and nouveau have done this for a long time.
I've run this personally all night hib/resume cycles with no fails.
Reviewed-by: Keith Packard <keithp@keithp.com>
Reported-by: Petr Tesarik <kernel@tesarici.cz>
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reported-by: Lots of misc segfaults after hibernate across the world.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=37142
Tested-by: Dave Airlie <airlied@redhat.com>
Tested-by: Bojan Smojver <bojan@rexursive.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This has been obsolescent for a while; time for the final push.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dave Jones <davej@redhat.com>
Cc: cpufreq@vger.kernel.org
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Martin Persson <martin.persson@stericsson.com>
Cc: Jonas Aaberg <jonas.aberg@stericsson.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
|
|
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
|
|
Fix typo in drivers/video/backlight/tosa_lcd.c
"tosa_lcd_reume" should be "tosa_lcd_resume".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
rename the nbd_device variable from "lo" to "nbd", since "lo" is just a name
copied from loop.c.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The IPMI watchdog timer clears or extends the timer on reboot/shutdown.
It was using the non-locking routine for setting the watchdog timer, but
this was causing race conditions. Instead, use the locking version to
avoid the races. It seems to work fine.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that the the IPMI driver is using a tasklet, we can simplify the
locking in the driver and get rid of the message lock.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The part of the IPMI driver that delivered panic information to the event
log and extended the watchdog timeout during a panic was not properly
handling the messages. It used static messages to avoid allocation, but
wasn't properly waiting for these, or wasn't properly handling the
refcounts.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The IPMI driver would release a lock, deliver a message, then relock.
This is obviously ugly, and this patch converts the message handler
interface to use a tasklet to schedule work. This lets the receive
handler be called from an interrupt handler with interrupts enabled.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We currently time out and retry KCS transactions after 1 second of waiting
for IBF or OBF. This appears to be too short for some hardware. The IPMI
spec says "All system software wait loops should include error timeouts.
For simplicity, such timeouts are not shown explicitly in the flow
diagrams. A five-second timeout or greater is recommended". Change the
timeout to five seconds to satisfy the slow hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Call the event handler immediately after starting the next message.
This change considerably decreases the IPMI transaction time (cuts off
~9ms for a single ipmitool transaction).
Signed-off-by: Srinivas_Gowda <srinivas_g_gowda@dell.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
|
|
Haven't seen this yet, but it doesn't hurt.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ValleyView has a new interrupt architecture; best to put it in a new set
of functions. Also make sure the ring mask functions handle ValleyView.
FIXME: fix flipping; need to enable interrupts and call prepare/finish
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ValleyView handles force wake differently than previous chipsets, so add
a couple of new functions for it. But leave it disabled by default
until we test it (need a chip with the Punit enabled first).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
... and bind it right to the PCI id.
Note that there are still a few things to fix here:
- we need to move the tlb flush to a better place in drm/i915.
- we need to check snoop support on vlv and implement it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: squash follow-on patch and add todo items to commit msg.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.linaro.org/people/sumitsemwal/linux-dma-buf
Pull dma-buf updates from Sumit Semwal:
"This includes the following key items:
- kernel cpu access support,
- flag-passing to dma_buf_fd,
- relevant Documentation updates, and
- some minor cleanups and fixes.
These changes are needed for the drm prime/dma-buf interface code that
Dave Airlie plans to submit in this merge window."
* 'for-linus-3.4' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: correct dummy function declarations.
dma-buf: document fd flags and O_CLOEXEC requirement
dma_buf: Add documentation for the new cpu access support
dma-buf: add support for kernel cpu access
dma-buf: don't hold the mutex around map/unmap calls
dma-buf: add get_dma_buf()
dma-buf: pass flags into dma_buf_fd.
dma-buf: add dma_data_direction to unmap dma_buf_op
dma-buf: Move code out of mutex-protected section in dma_buf_attach()
dma-buf: Return error instead of using a goto statement when possible
dma-buf: Remove unneeded sanity checks
dma-buf: Constify ops argument to dma_buf_export()
|
|
We need to flush the Gunit TLB when we update GTT PTEs on VLV, but the
register for doing so is above the range we normally map. Map the whole
register space to make sure we can get it.
v2: only map the larger space on gen7+ (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
HDMI register offsets are different in Valleyview. Add support for the
same.
v2: drop superfluous comments in HDMI init (Daniel)
Signed-off-by: Beeresh G <beeresh.g@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch adds support for programming drain latency registers of Pondicherry
memory arbiter of Valleyview.
v2: clarify function names (Daniel)
fix summary typo (Daniel)
v3: add parens (Ben)
make drain function return bool (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Reviewed-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Reviewed-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Set required clock gating and chicken bits on VLV.
v2: set PIXEL_SUBSPAN_COLLECT_OPT_DISABLE too (Ben)
move function below ivb version to pretend to be consistent (Ben)
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
ValleyView puts some display related registers like the PLL controls and
dividers behind the DPIO bus. Add simple indirect register access
routines to get to those registers.
v2: move new wait_for macro to intel_drv.h (Ben)
fix DPIO_PKT double write (Ben)
add debugfs file
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add register definitions for the new VLV PLL bits.
v2: remove unused bits & regs (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Add support for ValleyView watermark handling.
v2: remove unused reg & bit definitions (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
For use by the rest of the ValleyView code.
v2: fix desktop variant to not set is_mobile (Ben)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
|
|
Oddly enough a work_struct was already part of the firmware_work
structure but nobody was using it. Instead of creating a new
kthread for each request_firmware_nowait() call just schedule the
work on the system workqueue. This should avoid some overhead
in forking new threads when they're not strictly necessary.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
Recent patches to split up the three phases of request_firmware()
lead to a casting away of const in fw_create_instance(). We can
avoid this cast by splitting up fw_create_instance() a bit.
Make _request_firmware_setup() return a struct fw_priv and use
that struct instead of passing struct firmware to
_request_firmware(). Move the uevent and device file creation
bits to the loading phase and rename the function to
_request_firmware_load() to better reflect its purpose.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If firmware is requested asynchronously, by calling
request_firmware_nowait(), there is no reason to fail the request
(and warn the user) when the system is (presumably temporarily)
unready to handle it (because user space is not available yet or
frozen). For this reason, introduce an alternative routine for
read-locking umhelper_sem, usermodehelper_read_lock_wait(), that
will wait for usermodehelper_disabled to be unset (possibly with
a timeout) and make request_firmware_work_func() use it instead of
usermodehelper_read_trylock().
Accordingly, modify request_firmware() so that it uses
usermodehelper_read_trylock() to acquire umhelper_sem and remove
the code related to that lock from _request_firmware().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
|
|
Split _request_firmware() into three functions,
_request_firmware_prepare() doing preparatory work that need not be
done under umhelper_sem, _request_firmware_cleanup() doing the
post-error cleanup and _request_firmware() carrying out the remaining
operations.
This change is requisite for moving the acquisition of umhelper_sem
from _request_firmware() to the callers, which is going to be done
subsequently.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: stable@vger.kernel.org
|
|
Instead of two functions, read_lock_usermodehelper() and
usermodehelper_is_disabled(), used in combination, introduce
usermodehelper_read_trylock() that will only return with umhelper_sem
held if usermodehelper_disabled is unset (and will return -EAGAIN
otherwise) and make _request_firmware() use it.
Rename read_unlock_usermodehelper() to
usermodehelper_read_unlock() to follow the naming convention of the
new function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
|
|
Makes it more readable and maintainable. ValleyView will add its own
PLL update function in a later patch.
v2: split LVDS bits out of this patch (Daniel)
v3: fix dropped DP dithering hunk (Daniel)
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
danvet:
- fixup spurious whitespace change
- reorder patches to fix bisect breakage
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac
Pull EDAC fixes from Mauro Carvalho Chehab:
"A series of EDAC driver fixes. It also has one core fix at the
documentation, and a rename patch, fixing the name of the struct that
contains the rank information."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: rename channel_info to rank_info
i5400_edac: Avoid calling pci_put_device() twice
edac: i5100 ack error detection register after each read
edac: i5100 fix erroneous define for M1Err
edac: sb_edac: Fix a wrong value setting for the previous value
edac: sb_edac: Fix a INTERLEAVE_MODE() misuse
edac: sb_edac: Let the driver depend on PCI_MMCONFIG
edac: Improve the comments to better describe the memory concepts
edac/ppc4xx_edac: Fix compilation
Fix sb_edac compilation with 32 bits kernels
|
