summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2023-02-20octeontx2-af: Add NIX Errata workaround on CN10K siliconGeetha sowjanya
This patch adds workaround for below 2 HW erratas 1. Due to improper clock gating, NIXRX may free the same NPA buffer multiple times.. to avoid this, always enable NIX RX conditional clock. 2. NIX FIFO does not get initialized on reset, if the SMQ flush is triggered before the first packet is processed, it will lead to undefined state. The workaround to perform SMQ flush only if packet count is non-zero in MDQ. Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: Sai Krishna <saikrishnag@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20net: phy: Read EEE abilities when using .featuresAndrew Lunn
A PHY driver can use a static integer value to indicate what link mode features it supports, i.e, its abilities.. This is the old way, but useful when dynamically determining the devices features does not work, e.g. support of fibre. EEE support has been moved into phydev->supported_eee. This needs to be set otherwise the code assumes EEE is not supported. It is normally set as part of reading the devices abilities. However if a static integer value was used, the dynamic reading of the abilities is not performed. Add a call to genphy_c45_read_eee_abilities() to read the EEE abilities. Fixes: 8b68710a3121 ("net: phy: start using genphy_c45_ethtool_get/set_eee()") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20net: phy: Add locks to ethtool functionsAndrew Lunn
The phydev lock should be held while accessing members of phydev, or calling into the driver. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20net: phy: marvell: Use the unlocked genphy_c45_ethtool_get_eee()Andrew Lunn
phy_ethtool_get_eee() is about to gain locking of the phydev lock. This means it cannot be used within a PHY driver without causing a deadlock. Swap to using genphy_c45_ethtool_get_eee() which assumes the lock has already been taken. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20net: bcmgenet: fix MoCA LED controlDoug Berger
When the bcmgenet_mii_config() code was refactored it was missed that the LED control for the MoCA interface got overwritten by the port_ctrl value. Its previous programming is restored here. Fixes: 4f8d81b77e66 ("net: bcmgenet: Refactor register access in bcmgenet_mii_config") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20HID: mcp-2221: prevent UAF in delayed workBenjamin Tissoires
If the device is plugged/unplugged without giving time for mcp_init_work() to complete, we might kick in the devm free code path and thus have unavailable struct mcp_2221 while in delayed work. Canceling the delayed_work item is enough to solve the issue, because cancel_delayed_work_sync will prevent the work item to requeue itself. Fixes: 960f9df7c620 ("HID: mcp2221: add ADC/DAC support via iio subsystem") CC: stable@vger.kernel.org Acked-by: Jiri Kosina <jkosina@suse.cz> Link: https://lore.kernel.org/r/20230215-wip-mcp2221-v2-1-109f71fd036e@redhat.com Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
2023-02-20qede: fix interrupt coalescing configurationManish Chopra
On default driver load device gets configured with unexpected higher interrupt coalescing values instead of default expected values as memory allocated from krealloc() is not supposed to be zeroed out and may contain garbage values. Fix this by allocating the memory of required size first with kcalloc() and then use krealloc() to resize and preserve the contents across down/up of the interface. Signed-off-by: Manish Chopra <manishc@marvell.com> Fixes: b0ec5489c480 ("qede: preserve per queue stats across up/down of interface") Cc: stable@vger.kernel.org Cc: Bhaskar Upadhaya <bupadhaya@marvell.com> Cc: David S. Miller <davem@davemloft.net> Link: https://bugzilla.redhat.com/show_bug.cgi?id=2160054 Signed-off-by: Alok Prasad <palok@marvell.com> Signed-off-by: Ariel Elior <aelior@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-20net: ipa: add HW_PARAM_4 GSI registerAlex Elder
Starting at IPA v5.0, the number of event rings per EE is defined in a field in a new HW_PARAM_4 GSI register rather than HW_PARAM_2. Define this new register and its fields, and update the code that checks the number of rings supported by hardware to use the proper field based on IPA version. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: ipa: support different event ring encodingAlex Elder
Starting with IPA v5.0, a channel's event ring index is encoded in a field in the CH_C_CNTXT_1 GSI register rather than CH_C_CNTXT_0. Define a new field ID for the former register and encode the event ring in the appropriate register. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: ipa: avoid setting an undefined fieldAlex Elder
The GSI channel protocol field in the CH_C_CNTXT_0 GSI register is widened starting IPA v5.0, making the CHTYPE_PROTOCOL_MSB field added in IPA v4.5 unnecessary. Update the code to reflect this. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: ipa: kill ev_ch_e_cntxt_1_length_encode()Alex Elder
Now that we explicitly define each register field width there is no need to have a special encoding function for the event ring length. Add a field for this to the EV_CH_E_CNTXT_1 GSI register, and use it in place of ev_ch_e_cntxt_1_length_encode() (which can be removed). Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: ipa: kill gsi->virt_rawAlex Elder
Starting at IPA v4.5, almost all GSI registers had their offsets changed by a fixed amount (shifted downward by 0xd000). Rather than defining offsets for all those registers dependent on version, an adjustment was applied for most register accesses. This was implemented in commit cdeee49f3ef7f ("net: ipa: adjust GSI register addresses"). It was later modified to be a bit more obvious about the adjusment, in commit 571b1e7e58ad3 ("net: ipa: use a separate pointer for adjusted GSI memory"). We now are able to define every GSI register with its own offset, so there's no need to implement this special adjustment. So get rid of the "virt_raw" pointer, and just maintain "virt" as the (non-adjusted) base address of I/O mapped GSI register memory. Redefine the offsets of all GSI registers (other than the INTER_EE ones, which were not subject to the adjustment) for IPA v4.5+, subtracting 0xd000 from their defined offsets instead. Move the ERROR_LOG and ERROR_LOG_CLR definitions further down in the register definition files so all registers are defined in order of their offset. Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: ipa: fix an incorrect assignmentAlex Elder
I spotted an error in a patch posted this week, unfortunately just after it got accepted. The effect of the bug is that time-based interrupt moderation is disabled. This is not technically a bug, but it is not what is intended. The problem is that a |= assignment got implemented as a simple assignment, so the previously assigned value was ignored. Fixes: edc6158b18af ("net: ipa: define fields for event-ring related registers") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-20net: dpaa2-eth: do not always set xsk support in xdp_features flagLorenzo Bianconi
Do not always add NETDEV_XDP_ACT_XSK_ZEROCOPY bit in xdp_features flag but check if the NIC really supports it. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Link: https://lore.kernel.org/r/3dba6ea42dc343a9f2d7d1a6a6a6c173235e1ebf.1676471386.git.lorenzo@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2023-02-19firmware/efi sysfb_efi: Add quirk for Lenovo IdeaPad Duet 3Darrell Kavanagh
Another Lenovo convertable which reports a landscape resolution of 1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes. Signed-off-by: Darrell Kavanagh <darrell.kavanagh@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
2023-02-19IB/mlx5: Extend debug control for CC parametersEdward Srouji
This patch adds rtt_resp_dscp to the current debug controllability of congestion control (CC) parameters. rtt_resp_dscp can be read or written through debugfs. If set, its value overwrites the DSCP of the generated RTT response. Signed-off-by: Edward Srouji <edwards@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Link: https://lore.kernel.org/r/1dcc3440ee53c688f19f579a051ded81a2aaa70a.1676538714.git.leon@kernel.org Signed-off-by: Leon Romanovsky <leon@kernel.org>
2023-02-19Merge tag 'irqchip-6.3' of ↵Thomas Gleixner
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core Pull irqchip updates from Marc Zyngier: - New and improved irqdomain locking, closing a number of races that became apparent now that we are able to probe drivers in parallel - A bunch of OF node refcounting bugs have been fixed - We now have a new IPI mux, lifted from the Apple AIC code and made common. It is expected that riscv will eventually benefit from it - Two small fixes for the Broadcom L2 drivers - Various cleanups and minor bug fixes Link: https://lore.kernel.org/r/20230218143452.3817627-1-maz@kernel.org
2023-02-18Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 regression fix from Will Deacon: "Apologies for the _extremely_ late pull request here, but we had a 'perf' (i.e. CPU PMU) regression on the Apple M1 reported on Wednesday [1] which was introduced by bd2756811766 ("perf: Rewrite core context handling") during the merge window. Mark and I looked into this and noticed an additional problem caused by the same patch, where the 'CHAIN' event (used to combine two adjacent 32-bit counters into a single 64-bit counter) was not being filtered correctly. Mark posted a series on Thursday [2] which addresses both of these regressions and I queued it the same day. The changes are small, self-contained and have been confirmed to fix the original regression. Summary: - Fix 'perf' regression for non-standard CPU PMU hardware (i.e. Apple M1)" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: perf: reject CHAIN events at creation time arm_pmu: fix event CPU filtering
2023-02-18Merge tag 'block-6.2-2023-02-17' of git://git.kernel.dk/linuxLinus Torvalds
Pull block fix from Jens Axboe: "I guess this is what can happen when you prep things early for going away, something else comes in last minute. This one fixes another regression in 6.2 for NVMe, from this release, and hence we should probably get it submitted for 6.2. Still waiting for the original reporter (see bugzilla linked in the commit) to test this, but Keith managed to setup and recreate the issue and tested the patch that way" * tag 'block-6.2-2023-02-17' of git://git.kernel.dk/linux: nvme-pci: refresh visible attrs for cmb attributes
2023-02-18xen: sysfs: make kobj_type structure constantThomas Weißschuh
Since commit ee6d3dd4ed48 ("driver core: make kobj_type constant.") the driver core allows the usage of const struct kobj_type. Take advantage of this to constify the structure definition to prevent modification at runtime. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20230216-kobj_type-xen-v1-1-742423de7d71@weissschuh.net Signed-off-by: Juergen Gross <jgross@suse.com>
2023-02-18Merge branches 'apple/dart', 'arm/exynos', 'arm/renesas', 'arm/smmu', ↵Joerg Roedel
'x86/vt-d', 'x86/amd' and 'core' into next
2023-02-18iommu/amd: Skip attach device domain is same as new domainVasant Hegde
If device->domain is same as new domain then we can skip the device attach process. Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20230215052642.6016-2-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2023-02-18iommu: Attach device group to old domain in error pathVasant Hegde
iommu_attach_group() attaches all devices in a group to domain and then sets group domain (group->domain). Current code (__iommu_attach_group()) does not handle error path. This creates problem as devices to domain attachment is in inconsistent state. Flow: - During boot iommu attach devices to default domain - Later some device driver (like amd/iommu_v2 or vfio) tries to attach device to new domain. - In iommu_attach_group() path we detach device from current domain. Then it tries to attach devices to new domain. - If it fails to attach device to new domain then device to domain link is broken. - iommu_attach_group() returns error. - At this stage iommu_attach_group() caller thinks, attaching device to new domain failed and devices are still attached to old domain. - But in reality device to old domain link is broken. It will result in all sort of failures (like IO page fault) later. To recover from this situation, we need to attach all devices back to the old domain. Also log warning if it fails attach device back to old domain. Suggested-by: Lu Baolu <baolu.lu@linux.intel.com> Reported-by: Matt Fagnani <matt.fagnani@bell.net> Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Tested-by: Matt Fagnani <matt.fagnani@bell.net> Link: https://lore.kernel.org/r/20230215052642.6016-1-vasant.hegde@amd.com Link: https://bugzilla.kernel.org/show_bug.cgi?id=216865 Link: https://lore.kernel.org/lkml/15d0f9ff-2a56-b3e9-5b45-e6b23300ae3b@leemhuis.info/ Signed-off-by: Joerg Roedel <jroedel@suse.de>
2023-02-18Merge branch irq/bcm-l2-fixes into irq/irqchip-nextMarc Zyngier
* irq/bcm-l2-fixes: : . : Broadcom L2 irqchip fixes for correct handling of level interrupts, : courtesy of Florian Fainelli. : . irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interrupts irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interrupts Signed-off-by: Marc Zyngier <maz@kernel.org>
2023-02-18irqchip/irq-bcm7120-l2: Set IRQ_LEVEL for level triggered interruptsFlorian Fainelli
When support for the interrupt controller was added with a5042de2688d, we forgot to update the flags to be set to contain IRQ_LEVEL. While the flow handler is correct, the output from /proc/interrupts does not show such interrupts as being level triggered when they are, correct that. Fixes: a5042de2688d ("irqchip: bcm7120-l2: Add Broadcom BCM7120-style Level 2 interrupt controller") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221216230934.2478345-3-f.fainelli@gmail.com
2023-02-18irqchip/irq-brcmstb-l2: Set IRQ_LEVEL for level triggered interruptsFlorian Fainelli
When support for the level triggered interrupt controller flavor was added with c0ca7262088e, we forgot to update the flags to be set to contain IRQ_LEVEL. While the flow handler is correct, the output from /proc/interrupts does not show such interrupts as being level triggered when they are, correct that. Fixes: c0ca7262088e ("irqchip/brcmstb-l2: Add support for the BCM7271 L2 controller") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20221216230934.2478345-2-f.fainelli@gmail.com
2023-02-18watchdog: sbsa_wdog: Make sure the timeout programming is within the limitsGeorge Cherian
Make sure to honour the max_hw_heartbeat_ms while programming the timeout value to WOR. Clamp the timeout passed to sbsa_gwdt_set_timeout() to make sure the programmed value is within the permissible range. Fixes: abd3ac7902fb ("watchdog: sbsa: Support architecture version 1") Signed-off-by: George Cherian <george.cherian@marvell.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20230209021117.1512097-1-george.cherian@marvell.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: report options in sysfsThomas Weißschuh
This synchronizes the information reported by ioctl and sysfs. The mismatch is confusing because "wdctl" from util-linux uses the ioctl when used with root privileges and sysfs without. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221216-watchdog-sysfs-v2-2-6189311103a9@weissschuh.net [groeck: Fixed continuation line alignment] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: report fw_version in sysfsThomas Weißschuh
This synchronizes the information reported by ioctl and sysfs. The mismatch is confusing because "wdctl" from util-linux uses the ioctl when used with root privileges and sysfs without. The file is called "fw_version" instead of "firmware_version" as "firmware_version" is already used as custom attribute by single drivers. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221216-watchdog-sysfs-v2-1-6189311103a9@weissschuh.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: imx2_wdg: suspend watchdog in WAIT modeAndrej Picej
Putting device into the "Suspend-To-Idle" mode causes watchdog to trigger and resets the board after set watchdog timeout period elapses. Introduce new device-tree property "fsl,suspend-in-wait" which suspends watchdog in WAIT mode. This is done by setting WDW bit in WCR (Watchdog Control Register). Watchdog operation is restored after exiting WAIT mode as expected. WAIT mode corresponds with Linux's "Suspend-To-Idle". Signed-off-by: Andrej Picej <andrej.picej@norik.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221104070358.426657-2-andrej.picej@norik.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: pcwd_usb: Fix attempting to access uninitialized memoryLi Hua
The stack variable msb and lsb may be used uninitialized in function usb_pcwd_get_temperature and usb_pcwd_get_timeleft when usb card no response. The build waring is: drivers/watchdog/pcwd_usb.c:336:22: error: ‘lsb’ is used uninitialized in this function [-Werror=uninitialized] *temperature = (lsb * 9 / 5) + 32; ~~~~^~~ drivers/watchdog/pcwd_usb.c:328:21: note: ‘lsb’ was declared here unsigned char msb, lsb; ^~~ cc1: all warnings being treated as errors scripts/Makefile.build:250: recipe for target 'drivers/watchdog/pcwd_usb.o' failed make[3]: *** [drivers/watchdog/pcwd_usb.o] Error 1 Fixes: b7e04f8c61a4 ("mv watchdog tree under drivers") Signed-off-by: Li Hua <hucool.lihua@huawei.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221116020706.70847-1-hucool.lihua@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: Fix kmemleak in watchdog_cdev_registerChen Jun
kmemleak reports memory leaks in watchdog_dev_register, as follows: unreferenced object 0xffff888116233000 (size 2048): comm ""modprobe"", pid 28147, jiffies 4353426116 (age 61.741s) hex dump (first 32 bytes): 80 fa b9 05 81 88 ff ff 08 30 23 16 81 88 ff ff .........0#..... 08 30 23 16 81 88 ff ff 00 00 00 00 00 00 00 00 .0#............. backtrace: [<000000007f001ffd>] __kmem_cache_alloc_node+0x157/0x220 [<000000006a389304>] kmalloc_trace+0x21/0x110 [<000000008d640eea>] watchdog_dev_register+0x4e/0x780 [watchdog] [<0000000053c9f248>] __watchdog_register_device+0x4f0/0x680 [watchdog] [<00000000b2979824>] watchdog_register_device+0xd2/0x110 [watchdog] [<000000001f730178>] 0xffffffffc10880ae [<000000007a1a8bcc>] do_one_initcall+0xcb/0x4d0 [<00000000b98be325>] do_init_module+0x1ca/0x5f0 [<0000000046d08e7c>] load_module+0x6133/0x70f0 ... unreferenced object 0xffff888105b9fa80 (size 16): comm ""modprobe"", pid 28147, jiffies 4353426116 (age 61.741s) hex dump (first 16 bytes): 77 61 74 63 68 64 6f 67 31 00 b9 05 81 88 ff ff watchdog1....... backtrace: [<000000007f001ffd>] __kmem_cache_alloc_node+0x157/0x220 [<00000000486ab89b>] __kmalloc_node_track_caller+0x44/0x1b0 [<000000005a39aab0>] kvasprintf+0xb5/0x140 [<0000000024806f85>] kvasprintf_const+0x55/0x180 [<000000009276cb7f>] kobject_set_name_vargs+0x56/0x150 [<00000000a92e820b>] dev_set_name+0xab/0xe0 [<00000000cec812c6>] watchdog_dev_register+0x285/0x780 [watchdog] [<0000000053c9f248>] __watchdog_register_device+0x4f0/0x680 [watchdog] [<00000000b2979824>] watchdog_register_device+0xd2/0x110 [watchdog] [<000000001f730178>] 0xffffffffc10880ae [<000000007a1a8bcc>] do_one_initcall+0xcb/0x4d0 [<00000000b98be325>] do_init_module+0x1ca/0x5f0 [<0000000046d08e7c>] load_module+0x6133/0x70f0 ... The reason is that put_device is not be called if cdev_device_add fails and wdd->id != 0. watchdog_cdev_register wd_data = kzalloc [1] err = dev_set_name [2] .. err = cdev_device_add if (err) { if (wdd->id == 0) { // wdd->id != 0 .. } return err; // [1],[2] would be leaked To fix it, call put_device in all wdd->id cases. Fixes: 72139dfa2464 ("watchdog: Fix the race between the release of watchdog_core_data and cdev") Signed-off-by: Chen Jun <chenjun102@huawei.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221116012714.102066-1-chenjun102@huawei.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: Include <linux/kstrtox.h> when appropriateChristophe JAILLET
The kstrto<something>() functions have been moved from kernel.h to kstrtox.h. So, in order to eventually remove <linux/kernel.h> from <linux/watchdog.h>, include the latter directly in the appropriate files. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/08fd5512e569558231247515c04c8596a1d11004.1667646547.git.christophe.jaillet@wanadoo.fr Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: at91sam9_wdt: use devm_request_irq to avoid missing free_irq() in ↵ruanjinjie
error path free_irq() is missing in case of error in at91_wdt_init(), use devm_request_irq to fix that. Fixes: 5161b31dc39a ("watchdog: at91sam9_wdt: better watchdog support") Signed-off-by: ruanjinjie <ruanjinjie@huawei.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221116094950.3141943-1-ruanjinjie@huawei.com [groeck: Adjust multi-line alignment] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: rzg2l_wdt: Handle TYPE-B reset for RZ/V2MFabrizio Castro
As per section 48.4 of the HW User Manual, IPs in the RZ/V2M SoC need either a TYPE-A reset sequence or a TYPE-B reset sequence. More specifically, the watchdog IP needs a TYPE-B reset sequence. If the proper reset sequence isn't implemented, then resetting IPs may lead to undesired behaviour. In the restart callback of the watchdog driver the reset has basically no effect on the desired funcionality, as the register writes following the reset happen before the IP manages to come out of reset. Implement the TYPE-B reset sequence in the watchdog driver to address the issues with the restart callback on RZ/V2M. Fixes: ec122fd94eeb ("watchdog: rzg2l_wdt: Add rzv2m support") Signed-off-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20221117114907.138583-3-fabrizio.castro.jz@renesas.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: rzg2l_wdt: Issue a reset before we put the PM clocksLad Prabhakar
On RZ/Five SoC it was observed that setting timeout (to say 1 sec) wouldn't reset the system. The procedure described in the HW manual (Procedure for Activating Modules) for activating the target module states we need to start supply of the clock module before applying the reset signal. This patch makes sure we follow the same procedure to clear the registers of the WDT module, fixing the issues seen on RZ/Five SoC. While at it re-used rzg2l_wdt_stop() in rzg2l_wdt_set_timeout() as it has the same function calls. Fixes: 4055ee81009e ("watchdog: rzg2l_wdt: Add set_timeout callback") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20221117114907.138583-2-fabrizio.castro.jz@renesas.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: dw_wdt: stop on rebootCosmin Tanislav
HW running watchdogs are just watchdogs that are enabled before the Linux driver is probed, usually by the bootloader (eg. U-Boot). When the system is shutting down, the mechanism for keeping a HW running watchdog pinged is also stopped, but the watchdog itself is not stopped, causing a reset, and preventing the system from being shut down. Opt into stopping watchdogs on reboot. Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221118150809.102505-1-cosmin.tanislav@analog.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: ziirave_wdt: Convert to i2c's .probe_new()Uwe Kleine-König
The probe function doesn't make use of the i2c_device_id * parameter so it can be trivially converted. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221118224540.619276-597-uwe@kleine-koenig.org Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: iTCO_wdt: Report firmware_versionThomas Weißschuh
Synchronize the reported information in dmesg and the watchdog APIs. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221125221240.2818-1-linux@weissschuh.net Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18watchdog: da9062: da9063: use unlocked xfer function in restartPrimoz Fiser
Machine resets via da9062/da9063 PMICs are challenging since one needs to use special i2c atomic transfers due to the fact interrupts are disabled in such late system stages. This is the reason both PMICs don't use regmap and have instead opted for i2c_smbus_write_byte_data() in restart handlers. However extensive testing revealed that even using atomic safe function is not enough and occasional resets fail with error message "Failed to shutdown (err = -11)". This is due to the fact that function i2c_smbus_write_byte_data() in turn calls __i2c_lock_bus_helper() which might fail with -EAGAIN when bus lock is already taken and cannot be released anymore. Thus replace i2c_smbus_write_byte_data() with unlocked flavor of i2c_smbus_xfer() function to avoid above dead-lock scenario. At this system stage we don't care about proper locking anymore and only want proper machine reset to be carried out. Signed-off-by: Primoz Fiser <primoz.fiser@norik.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20221216083645.2574077-1-primoz.fiser@norik.com [groeck: Fixed continuation line alignment] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
2023-02-18platform/x86: nvidia-wmi-ec-backlight: Add force module parameterHans de Goede
On some Lenovo Legion models, the backlight might be driven by either one of nvidia_wmi_ec_backlight or amdgpu_bl0 at different times. When the Nvidia WMI EC backlight interface reports the backlight is controlled by the EC, the current backlight handling only registers nvidia_wmi_ec_backlight (and registers no other backlight interfaces). This hides (never registers) the amdgpu_bl0 interface, where as prior to 6.1.4 users would have both nvidia_wmi_ec_backlight and amdgpu_bl0 and could work around things in userspace. Add a force module parameter which can be used with acpi_backlight=native to restore the old behavior as a workound (for now) by passing: "acpi_backlight=native nvidia-wmi-ec-backlight.force=1" Fixes: 8d0ca287fd8c ("platform/x86: nvidia-wmi-ec-backlight: Use acpi_video_get_backlight_type()") Link: https://bugzilla.kernel.org/show_bug.cgi?id=217026 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Daniel Dadap <ddadap@nvidia.com> Link: https://lore.kernel.org/r/20230217144208.5721-1-hdegoede@redhat.com
2023-02-18net/mlx5e: RX, Remove doubtful unlikely callGal Pressman
When building an skb in non-linear mode, it is not likely nor unlikely that the xdp buff has fragments, it depends on the size of the packet received. Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
2023-02-18net/mlx5e: Fix outdated TLS commentTariq Toukan
Comment is outdated since commit 40379a0084c2 ("net/mlx5_fpga: Drop INNOVA TLS support"). Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5e: Remove unused function mlx5e_sq_xmit_simpleTariq Toukan
The last usage was removed as part of commit 40379a0084c2 ("net/mlx5_fpga: Drop INNOVA TLS support"). Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5e: Allow offloading of ct 'new' matchVlad Buslov
Allow offloading filters that match on conntrack 'new' state in order to enable UDP NEW offload in the following patch. Unhardcode ct 'established' from ct modify header infrastructure code and determine correct ct state bit according to the metadata action 'cookie' field. Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Reviewed-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5e: Implement CT entry updateVlad Buslov
With support for UDP NEW offload the flow_table may now send updates for existing flows. Support properly replacing existing entries by updating flow restore_cookie and replacing the rule with new one with the same match but new mod_hdr action that sets updated ctinfo. Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Reviewed-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5: Simplify eq list traversalParav Pandit
EQ list is read only while finding the matching EQ. Hence, avoid *_safe() version. Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Shay Drory <shayd@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
2023-02-18net/mlx5e: Remove redundant page argument in mlx5e_xdp_handle()Tariq Toukan
Remove the page parameter, it can be derived from the xdp_buff member of mlx5e_xdp_buff. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5e: Remove redundant page argument in mlx5e_xmit_xdp_buff()Tariq Toukan
Remove the page parameter, it can be derived from the xdp_buff. Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2023-02-18net/mlx5e: Switch to using napi_build_skb()Tariq Toukan
Use napi_build_skb() which uses NAPI percpu caches to obtain skbuff_head instead of inplace allocation. napi_build_skb() calls napi_skb_cache_get(), which returns a cached skb, or allocates a bulk of NAPI_SKB_CACHE_BULK (16) if cache is empty. Performance test: TCP single stream, single ring, single core, default MTU (1500B). Before: 26.5 Gbits/sec After: 30.1 Gbits/sec (+13.6%) Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
generated by cgit (git 2.34.1) at 2025-09-11 23:50:21 +0000