| Age | Commit message (Collapse) | Author |
|---|
|
DC5 and DC6 counter register tells about residency of DC5 and DC6.
Added the same in debugfs file.
v2 : Remove csr_version check.
Added generic check regarding DC counters for Gen9 onwards. (Rodrigo)
v3 : Simplified gen checks. (Chris)
v4 : Simplified "if" ladder for multiple gens.
v5 : Removed unnecessary comment.
Signed-off-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538762926-4880-1-git-send-email-jyoti.r.yadav@intel.com
|
|
Except for the new HW header id, this works just like TSO6 on L3 devices
and reuses all the existing data path support in qeth_xmit().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds TSO6 support for L3 qeth devices.
Just like for standard IPv6 traffic, TSO6 doesn't use IP offload and
thus runs over the normal qeth_xmit() path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO6 requires the full programming sequence, and not just a simple
START command. This implements the additional ENABLE command, and adds
some sanity checks that were missing for the START command.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for IPv6 TSO, turn the protocol version into a parameter
for the TSO control code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resumes promisc mode and vlan filter status after
loopback test.
Fixes: 3b75c3df599d ("net: hns3: net: hns3: Add support for IFF_ALLMULTI flag")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch resumes promisc mode and vlan filter status after reset.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver does nothing when mac vlan table is full.
In this case, the packet with new mac address will be dropped
by hardware. This patch adds check for the result of sync mac
address, and enable promisc mode when mac vlan table is full.
Furtherly, disable vlan filter when enable promisc by user
command.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Highlights:
* merge net-next, so I can finish the hwsim workqueue removal
* fix TXQ NULL pointer issue that was reported multiple times
* minstrel cleanups from Felix
* simplify lib80211 code by not using skcipher, note that this
will conflict with the crypto tree (and this new code here
should be used)
* use new netlink policy validation in nl80211
* fix up SAE (part of WPA3) in client-mode
* FTM responder support in the stack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update Static Power Gate mode UVD status clear
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Set VCPU busy after gate power during vcn Static Power Gate start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Apply new UMC enable for VNC Dynamic Power Gate mode
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove Sitatic Power Gate mode unused steps during vcn start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add Static Power Gate mode Register XX check
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Move Static Power Gate mode mc resume after MPC control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update Static Power Gate mode VCN global tiling
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update Static Power Gate mode VCN memory control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Apply new UMC enable for VNC Dynamic Power Gate mode start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Remove Dynamic Power Gate mode unused steps during VCN start
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add Dynamic Power Gate mode Register XX check
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update Dynamic Power Gate mode VCN global tiling registers
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update Dynamic Power Gate mode VCN memory control
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Reduce unnecessary local variable.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add ring write/read pointer check for VCN dynamic power gate mode
stop,to make sure that no job is left in ring before turn off DPG mode.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update latest static power gate mode stop function for VCN
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Update latest UVD_MPC register for VCN. Use defined
macro to replace value for readability.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add new register offset/mask for VCN to support
latest VCN implementation.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY] dp debugfs file does not exist for eDP under
/sys/kernel/debug/dri/0/eDP-1. the root is phy debugfs
is created for dp connector only.
[HOW] for eDP connector, create phy debugfs too.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For sriov, when first run windows guest, then run linux guest, the gds
vmid0 size will be reset to 0 by windows guest. So if the value has been
reset to 0, then set the value to the default value in linux guest.
v2:
Fixed value instead of reading mmGDS_VMID0_SIZE.
v3:
Set the default value of the switch.
Signed-off-by: Emily Deng <Emily.Deng@amd.com>
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need to make sure that we don't race between job completion and
timeout.
v2: put revert label after calling the handling manually
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Cleanup starting the timeout a bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Give user some hints when the power profile setting is not supported.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Correctly translate the power profile specified by user to workload
type accepted by SMU fw.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079cc3 ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board.
The Lochnagar board provides power supplies for the attached
CODEC/Amp device. Currently this driver supports the microphone
supplies and the digital core voltage for the attached
device. There are some additional supplies that will be
added in time but these supplies are sufficient for most
systems/use-cases.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix a stupid typo introduced in the refactoring.
Fixes: 0efe5523 ("fore200e: simplify fore200e_bus usage")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The two PNMI macros are never used
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/usb/cdc_ncm.c: In function 'cdc_ncm_status':
drivers/net/usb/cdc_ncm.c:1603:22: warning:
variable 'ctx' set but not used [-Wunused-but-set-variable]
struct cdc_ncm_ctx *ctx;
It not used any more after
commit fa83dbeee558 ("net: cdc_ncm: remove redundant "disconnected" flag")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd writes:
"ARM: SoC fixes for 4.19
Two last minute bugfixes, both for NXP platforms:
* The Layerscape 'qbman' infrastructure suffers from probe ordering
bugs in some configurations, a two-patch series adds a hotfix for
this. 4.20 will have a longer set of patches to rework it.
* The old imx53-qsb board regressed in 4.19 after the addition
of cpufreq support, adding a set of explicit operating points
fixes this."
* tag 'armsoc-fixes-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: fsl: qman_portals: defer probe after qman's probe
soc: fsl: qbman: add APIs to retrieve the probing status
ARM: dts: imx53-qsb: disable 1.2GHz OPP
|
|
The kbuild robot reports:
drivers/nvdimm/label.c:500:32: warning: restricted __le32 degrades to integer
...read 'nslot' into a local u32.
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch adds logic that is meant to make use of the namespace index data
to reduce the number of reads that are needed to initialize a given
namespace. The general idea is that once we have enough data to validate
the namespace index we do so and then proceed to fetch only those labels
that are not listed as being "free". By doing this I am seeing a total time
reduction from about 4-5 seconds to 2-3 seconds for 24 NVDIMM modules each
with 128K of label config area.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch splits the initialization of the label data into two functions.
One for doing the init, and another for reading the actual configuration
data. The idea behind this is that by doing this we create a symmetry
between the getting and setting of config data in that we have a function
for both. In addition it will make it easier for us to identify the bits
that are related to init versus the pieces that are a wrapper for reading
data from the ACPI interface.
So for example by splitting things out like this it becomes much more
obvious that we were performing checks that weren't necessarily related to
the set/get operations such as relying on ndd->data being present when the
set and get ops should not care about a locally cached copy of the label
area.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch removes an empty statement from an if expression and promotes
the else statement to the if expression with the expression logic reversed.
I feel this is more readable as the empty statement can lead to issues if
any additional logic was ever added.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
When working on the label code I found it rather confusing to see several
spots that reference a minimum label size of 256 while working with labels
that are 128 bytes in size.
This patch is meant to provide a clarification on one of the comments that
was at the heart of the issue. Specifically for version 1.2 and later of
the namespace specification the minimum label size is 256, prior to that
the minimum label size was 128. So we should state that as such to avoid
confusion.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch adds validation for the labeloff field in the indexes.
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The file is GPL v2 or later.
Acked-by: Mircea Caprioru <mircea.caprioru@analog.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
