summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2024-07-05USB: serial: option: add support for Foxconn T99W651Slark Xiao
T99W651 is a RNDIS based modem device. There are 3 serial ports need to be enumerated: Diag, NMEA and AT. Test evidence as below: T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e145 Rev=05.15 S: Manufacturer=QCOM S: Product=SDXPINN-IDP _SN:93B562B2 S: SerialNumber=82e6fe26 C: #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=ef(misc ) Sub=04 Prot=01 Driver=rndis_host I: If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option I: If#=0x5 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) I: If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) 0&1: RNDIS, 2:AT, 3:NMEA, 4:DIAG, 5:QDSS, 6:ADB QDSS is not a serial port. Signed-off-by: Slark Xiao <slark_xiao@163.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>
2024-07-05USB: serial: option: add Netprisma LCUK54 series modulesMank Wang
Add support for Netprisma LCUK54 series modules. LCUK54-WRD-LWW(0x3731/0x0100): NetPrisma LCUK54-WWD for Global LCUK54-WRD-LWW(0x3731/0x0101): NetPrisma LCUK54-WRD for Global SKU LCUK54-WRD-LCN(0x3731/0x0106): NetPrisma LCUK54-WRD for China SKU LCUK54-WRD-LWW(0x3731/0x0111): NetPrisma LCUK54-WWD for SA LCUK54-WRD-LWW(0x3731/0x0112): NetPrisma LCUK54-WWD for EU LCUK54-WRD-LWW(0x3731/0x0113): NetPrisma LCUK54-WWD for NA LCUK54-WWD-LCN(0x3731/0x0115): NetPrisma LCUK54-WWD for China EDU LCUK54-WWD-LWW(0x3731/0x0116): NetPrisma LCUK54-WWD for Golbal EDU Above products use the exact same interface layout and option driver: MBIM + GNSS + DIAG + NMEA + AT + QDSS + DPL T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 5 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=3731 ProdID=0101 Rev= 5.04 S: Manufacturer=NetPrisma S: Product=LCUK54-WRD S: SerialNumber=b6250c36 C:* #Ifs= 8 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 6 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=70 Driver=(none) E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 7 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=80 Driver=(none) E: Ad=8f(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by: Mank Wang <mank.wang@netprisma.us> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org>
2024-07-05gpiolib: of: add polarity quirk for TSC2005Dmitry Torokhov
DTS for Nokia N900 incorrectly specifies "active high" polarity for the reset line, while the chip documentation actually specifies it as "active low". In the past the driver fudged gpiod API and inverted the logic internally, but it was changed in d0d89493bff8. Fixes: d0d89493bff8 ("Input: tsc2004/5 - switch to using generic device properties") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/ZoWXwYtwgJIxi-hD@google.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
2024-07-05Merge v6.10-rc6 into drm-nextDaniel Vetter
The exynos-next pull is based on a newer -rc than drm-next. hence backmerge first to make sure the unrelated conflicts we accumulated don't end up randomly in the exynos merge pull, but are separated out. Conflicts are all benign: Adjacent changes in amdgpu and fbdev-dma code, and cherry-pick conflict in xe. Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2024-07-05net: stmmac: Add DW XPCS specified via "pcs-handle" supportSerge Semin
Recently the DW XPCS DT-bindings have been introduced and the DW XPCS driver has been altered to support the DW XPCS registered as a platform device. In order to have the DW XPCS DT-device accessed from the STMMAC driver let's alter the STMMAC PCS-setup procedure to support the "pcs-handle" property containing the phandle reference to the DW XPCS device DT-node. The respective fwnode will be then passed to the xpcs_create_fwnode() function which in its turn will create the DW XPCS descriptor utilized in the main driver for the PCS-related setups. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: stmmac: Create DW XPCS device with particular addressSerge Semin
Currently the only STMMAC platform driver using the DW XPCS code is the Intel mGBE device driver. (It can be determined by finding all the drivers having the stmmac_mdio_bus_data::has_xpcs flag set.) At the same time the low-level platform driver masks out the DW XPCS MDIO-address from being auto-detected as PHY by the MDIO subsystem core. Seeing the PCS MDIO ID is known the procedure of the DW XPCS device creation can be simplified by dropping the loop over all the MDIO IDs. From now the DW XPCS device descriptor will be created for the MDIO-bus address pre-defined by the platform drivers via the stmmac_mdio_bus_data::pcs_mask field. Note besides this shall speed up a bit the Intel mGBE probing. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Add fwnode-based descriptor creation methodSerge Semin
It's now possible to have the DW XPCS device defined as a standard platform device for instance in the platform DT-file. Although that functionality is useless unless there is a way to have the device found by the client drivers (STMMAC/DW *MAC, NXP SJA1105 Eth Switch, etc). Provide such ability by means of the xpcs_create_fwnode() method. It needs to be called with the device DW XPCS fwnode instance passed. That node will be then used to find the MDIO-device instance in order to create the DW XPCS descriptor. Note the method semantics and name is similar to what has been recently introduced in the Lynx PCS driver. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Add Synopsys DW xPCS platform device driverSerge Semin
Synopsys DesignWare XPCS IP-core can be synthesized with the device CSRs being accessible over the MCI or APB3 interface instead of the MDIO bus (see the CSR_INTERFACE HDL parameter). Thus all the PCS registers can be just memory mapped and be a subject of the standard MMIO operations of course taking into account the peculiarities of the Clause C45 CSRs mapping. From that perspective the DW XPCS devices would look as just normal platform devices for the kernel. On the other hand in order to have the DW XPCS devices handled by the pcs-xpcs.c driver they need to be registered in the framework of the MDIO-subsystem. So the suggested change is about providing a DW XPCS platform device driver registering a virtual MDIO-bus with a single MDIO-device representing the DW XPCS device. DW XPCS platform device is supposed to be described by the respective compatible string "snps,dw-xpcs" (or with the PMA-specific compatible string), CSRs memory space and optional peripheral bus and reference clock sources. Depending on the INDIRECT_ACCESS IP-core synthesize parameter the memory-mapped reg-space can be represented as either directly or indirectly mapped Clause 45 space. In the former case the particular address is determined based on the MMD device and the registers offset (5 + 16 bits all together) within the device reg-space. In the later case there is only 8 lower address bits are utilized for the registers mapping (255 CSRs). The upper bits are supposed to be written into the respective viewport CSR in order to select the respective MMD sub-page. Note, only the peripheral bus clock source is requested in the platform device probe procedure. The core and pad clocks handling has been implemented in the framework of the xpcs_create() method intentionally since the clocks-related setups are supposed to be performed later, during the DW XPCS main configuration procedures. (For instance they will be required for the DW Gen5 10G PMA configuration.) Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Introduce DW XPCS info structureSerge Semin
The being introduced structure will preserve the PCS and PMA IDs retrieved from the respective DW XPCS MMDs or potentially pre-defined by the client drivers. (The later change will be introduced later in the framework of the commit adding the memory-mapped DW XPCS devices support.) The structure fields are filled in in the xpcs_get_id() function, which used to be responsible for the PCS Device ID getting only. Besides of the PCS ID the method now fetches the PMA/PMD IDs too from MMD 1, which used to be done in xpcs_dev_flag(). The retrieved PMA ID will be from now utilized for the PMA-specific tweaks like it was introduced for the Wangxun TxGBE PCS in the commit f629acc6f210 ("net: pcs: xpcs: support to switch mode for Wangxun NICs"). Note 1. The xpcs_get_id() error-handling semantics has been changed. From now the error number will be returned from the function. There is no point in the next IOs or saving 0xffs and then looping over the actual device IDs if device couldn't be reached. -ENODEV will be returned if the very first IO operation failed thus indicating that no device could be found. Note 2. The PCS and PMA IDs macros have been converted to enum'es. The enum'es will be populated later in another commit with the virtual IDs identifying the DW XPCS devices which have some platform-specifics, but have been synthesized with the default PCS/PMA ID. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Convert xpcs_compat to dw_xpcs_compatSerge Semin
The xpcs_compat structure has been left as the only dw-prefix-less structure since the previous commit. Let's unify at least the structures naming in the driver by adding the dw_-prefix to it. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Convert xpcs_id to dw_xpcs_descSerge Semin
A structure with the PCS/PMA MMD IDs data is being introduced in one of the next commits. In order to prevent the names ambiguity let's convert the xpcs_id structure name to dw_xpcs_desc. The later version is more suitable since the structure content is indeed the device descriptor containing the data and callbacks required for the driver to correctly set the device up. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Split up xpcs_create() body to sub-functionsSerge Semin
As an initial preparation before adding the fwnode-based DW XPCS device support let's split the xpcs_create() function code up to a set of the small sub-functions. Thus the xpcs_create() implementation will get to look simpler and turn to be more coherent. Further updates will just touch the new sub-functions a bit: add platform-specific device info, add the reference clock getting and enabling. The xpcs_create() method will now contain the next static methods calls: xpcs_create_data() - create the DW XPCS device descriptor, pre-initialize it' fields and increase the mdio device refcount-er; xpcs_init_id() - find XPCS ID instance and save it in the device descriptor; xpcs_init_iface() - find MAC/PCS interface descriptor and perform basic initialization specific to it: soft-reset, disable polling. The update doesn't imply any semantic change but merely makes the code looking simpler and more ready for adding new features support. Note the xpcs_destroy() has been moved to being defined below the xpcs_create_mdiodev() function as the driver now implies having the protagonist-then-antagonist functions definition order. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05net: pcs: xpcs: Move native device ID macro to linux/pcs/pcs-xpcs.hSerge Semin
One of the next commits will alter the DW XPCS driver to support setting a custom device ID for the particular MDIO-device detected on the platform. The generic DW XPCS ID can be used as a custom ID as well in case if the DW XPCS-device was erroneously synthesized with no or some undefined ID. In addition to that having all supported DW XPCS device IDs defined in a single place will improve the code maintainability and readability. Note while at it rename the macros to being shorter and looking alike to the already defined NXP XPCS ID macro. Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2024-07-05slimbus: Fix struct and documentation alignment in stream.cAmit Vadhavana
The placement of the `segdist_codes` array documentation was corrected to conform with kernel documentation guidelines. The `@segdist_codes` was placed incorrectly within the struct `segdist_code` documentation block, which led to a potential misinterpretation of the code structure. The `segdist_codes` array documentation was moved outside the struct block, and a separate comment block was provided for it. This change ensures that clarity and proper alignment with kernel documentation standards are maintained. A kernel-doc warning was addressed: ./drivers/slimbus/stream.c:49: warning: Excess struct member 'segdist_codes' description in 'segdist_code' Signed-off-by: Amit Vadhavana <av2082000@gmail.com> Reviewed-by: Ricardo B. Marliere <ricardo@marliere.net> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705080234.424587-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05misc: fastrpc: use coherent pool for untranslated Compute BanksDylan Van Assche
Use fastrpc_remote_heap_alloc to allocate from the FastRPC device instead of the Compute Bank when the session ID is 0. This ensures that the allocation is inside the coherent DMA pool which is already accessible to the DSP. This is necessary to support FastRPC devices which do not have dedicated Compute Banks such as the SLPI on the SDM845. The latter uses an allocated CMA region instead of FastRPC Compute Banks. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Ekansh Gupta <quic_ekangupt@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705075900.424100-6-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05misc: fastrpc: support complete DMA pool access to the DSPDylan Van Assche
To support FastRPC Context Banks which aren't mapped via the SMMU, make the whole reserved memory region available to the DSP to allow access to coherent buffers. This is performed by assigning the memory to the DSP via a hypervisor call to set the correct permissions for the Virtual Machines on the DSP. This is only necessary when a memory region is provided for SLPI DSPs so guard this with a domain ID check. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Ekansh Gupta <quic_ekangupt@quicinc.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705075900.424100-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05misc: fastrpc: add missing MODULE_DESCRIPTION() macroJeff Johnson
make allmodconfig && make W=1 C=1 reports: WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/misc/fastrpc.o Add the missing invocation of the MODULE_DESCRIPTION() macro. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705075900.424100-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05misc: fastrpc: Add missing dev_err newlinesEkansh Gupta
Few dev_err calls are missing newlines. This can result in unrelated lines getting appended which might make logs difficult to understand. Add trailing newlines to avoid this. Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705075900.424100-3-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05misc: fastrpc: Use memdup_user()Thorsten Blum
Switching to memdup_user() overwrites the allocated memory only once, whereas kzalloc() followed by copy_from_user() initializes the allocated memory to zero and then immediately overwrites it. Fixes the following Coccinelle/coccicheck warning reported by memdup_user.cocci: WARNING opportunity for memdup_user Signed-off-by: Thorsten Blum <thorsten.blum@toblux.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705075900.424100-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()Lee Jones
Userspace provided string 's' could trivially have the length zero. Left unchecked this will firstly result in an OOB read in the form `if (str[0 - 1] == '\n') followed closely by an OOB write in the form `str[0 - 1] = '\0'`. There is already a validating check to catch strings that are too long. Let's supply an additional check for invalid strings that are too short. Signed-off-by: Lee Jones <lee@kernel.org> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20240705074339.633717-1-lee@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: core: Implement force_ro sysfs attributeMarek Vasut
Implement "force_ro" sysfs attribute to allow users to set read-write devices as read-only and back to read-write from userspace. The choice of the name is based on MMC core 'force_ro' attribute. This solves a situation where an AT24 I2C EEPROM with GPIO based nWP signal may have to be occasionally updated. Such I2C EEPROM device is usually set as read-only during most of the regular system operation, but in case it has to be updated in a controlled manner, it could be unlocked using this new "force_ro" sysfs attribute and then re-locked again. The "read-only" DT property and config->read_only configuration is respected and is used to set default state of the device, read-only or read-write, for devices which do implement .reg_write function. For devices which do not implement .reg_write function, the device is unconditionally read-only and the "force_ro" attribute is not visible. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-16-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: Use sysfs_emit() for type attributeMarek Vasut
Use sysfs_emit() instead of sprintf() to follow best practice per Documentation/filesystems/sysfs.rst " show() should only use sysfs_emit()... " Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-15-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: core: drop unnecessary range checks in sysfs callbacksThomas Weißschuh
The same checks have already been done in sysfs_kf_bin_write() and sysfs_kf_bin_read() just before the callbacks are invoked. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-12-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: core: remove global nvmem_cells_groupThomas Weißschuh
nvmem_cells_groups is a global variable that is also mutated. This is complicated and error-prone. Instead use a normal stack variable. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-11-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: core: add single sysfs groupThomas Weißschuh
The sysfs core provides a function to easily register a single group. Use it and remove the now unnecessary nvmem_cells_groups array. Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-10-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: rockchip-efuse: set type to OTPHeiko Stuebner
This device currently reports an "Unknown" type in sysfs. Since it is an eFuse hardware device, set its type to OTP. Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-7-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: rockchip-otp: Set type to OTPHeiko Stuebner
The Rockchip OTP is obviously an OTP memory, so document this fact. Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-6-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: rockchip-otp: set add_legacy_fixed_of_cells config optionHeiko Stuebner
The Rockchip OTP describes its layout via devicetree subnodes, so set the appropriate property. Fixes: 2cc3b37f5b6d ("nvmem: add explicit config option to read old syntax fixed OF cells") Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: meson-efuse: Replacing the use of of_node_put to __freeMarileneGarcia
Use __free for device_node values, and thus drop calls to of_node_put. The goal is to reduce memory management issues by using this scope-based of_node_put() cleanup to simplify function exit handling. When using __free a resource is allocated within a block, it is automatically freed at the end of the block. Suggested-by: Julia Lawall <julia.lawall@inria.fr> Signed-off-by: MarileneGarcia <marilene.agarcia@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05nvmem: add missing MODULE_DESCRIPTION() macrosJeff Johnson
make allmodconfig && make W=1 C=1 reports: WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/nvmem/nvmem-apple-efuses.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/nvmem/nvmem_brcm_nvram.o WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/nvmem/nvmem_u-boot-env.o Add the missing invocations of the MODULE_DESCRIPTION() macro. Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20240705074852.423202-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2024-07-05Merge tag 'drm-xe-next-2024-07-02' of ↵Daniel Vetter
https://gitlab.freedesktop.org/drm/xe/kernel into drm-next Driver Changes: - Fix in migration code (Auld) - Simplification in HWMon related code (Karthik) - Fix in forcewake logic (Nirmoy) - Fix engine utilization information (umesh) - Clean up on MOCS related code (Roper) - Fix on multicast register (Roper) - Fix TLB invalidation timeout (Nirmoy) - More SRIOV preparation (Michal) - Fix out-of-bounds array access (Lucas) - Fixes around some mutex utilization (Ashutosh, Vinay) - Expand LNL workaround to BMG (Vinay) Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> From: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/ZoROvquFrTFhk3Pb@intel.com
2024-07-05block: Remove REQ_OP_ZONE_RESET_ALL emulationDamien Le Moal
Now that device mapper can handle resetting all zones of a mapped zoned device using REQ_OP_ZONE_RESET_ALL, all zoned block device drivers support this operation. With this, the request queue feature BLK_FEAT_ZONE_RESETALL is not necessary and the emulation code in blk-zone.c can be removed. Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20240704052816.623865-5-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-07-05dm: handle REQ_OP_ZONE_RESET_ALLDamien Le Moal
This commit implements processing of the REQ_OP_ZONE_RESET_ALL operation for zoned mapped devices. Given that this operation always has a BIO sector of 0 and a 0 size, processing through the regular BIO __split_and_process_bio() function does not work because this function would always select the first target. Instead, handling of this operation is implemented using the function __send_zone_reset_all(). Similarly to the __send_empty_flush() function, the new __send_zone_reset_all() function manually goes through all targets of a mapped device table doing the following: 1) If the target can natively support REQ_OP_ZONE_RESET_ALL, __send_duplicate_bios() is used to forward the reset all operation to the target. This case is handled with the __send_zone_reset_all_native() function. 2) For other targets, the function __send_zone_reset_all_emulated() is executed to emulate the execution of REQ_OP_ZONE_RESET_ALL using regular REQ_OP_ZONE_RESET operations. Targets that can natively support REQ_OP_ZONE_RESET_ALL are identified using the new target field zone_reset_all_supported. This boolean is set to true in for targets that have reliable zone limits, that is, targets that map all sequential write required zones of their zoned device(s). Setting this field is handled in dm_set_zones_restrictions() and device_get_zone_resource_limits(). For targets with unreliable zone limits, REQ_OP_ZONE_RESET_ALL must be emulated (case 2 above). This is implemented with __send_zone_reset_all_emulated() and is similar to the block layer function blkdev_zone_reset_all_emulated(): first a report zones is done for the zones of the target to identify zones that need reset, that is, any sequential write required zone that is not already empty. This is done using a bitmap and the function dm_zone_get_reset_bitmap() which sets to 1 the bit corresponding to a zone that needs reset. Next, this zone bitmap is inspected and a clone BIO modified to use the REQ_OP_ZONE_RESET operation issued for any zone with its bit set in the zone bitmap. This implementation is more efficient than what the block layer does with blkdev_zone_reset_all_emulated(), which is always used for DM zoned devices currently: as we can natively use REQ_OP_ZONE_RESET_ALL on targets mapping all sequential write required zones, resetting all zones of a zoned mapped device can be much faster compared to always emulating this operation using regular per-zone reset. In the worst case, this implementation is as-efficient as the block layer emulation. This reduction in the time it takes to reset all zones of a zoned mapped device depends directly on the mapped device targets mapping (reliable zone limits or not). Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20240704052816.623865-4-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-07-05dm: Refactor is_abnormal_io()Damien Le Moal
Use a single switch-case to simplify is_abnormal_io() and make this function more readable and easier to modify. Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20240704052816.623865-3-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-07-05null_blk: Introduce the zone_full parameterDamien Le Moal
Allow creating a zoned null_blk device with the initial state of its sequential write required zones to be FULL. This is convenient to avoid having to first write these zones to perform read performance evaluation or test zone management operations such as zone reset (and zone reset all). Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20240704052816.623865-2-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-07-05loop: remove the unused inode variable in loop_configureChristoph Hellwig
Remove the inode variable now that the last user is gone. Fixes: a17ece76bcfe ("loop: regularize upgrading the block size for direct I/O") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20240705053114.2042976-1-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk>
2024-07-05cpufreq: pcc: Remove empty exit() callbackViresh Kumar
The exit() callback is optional, remove the empty one. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Rafael J. Wysocki <rafael@kernel.org>
2024-07-05cpufreq: loongson2: Remove empty exit() callbackViresh Kumar
The exit() callback is optional, remove the empty one. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Acked-by: Rafael J. Wysocki <rafael@kernel.org>
2024-07-05cpufreq: nforce2: Remove empty exit() callbackViresh Kumar
The exit() callback is optional, remove the empty one. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Rafael J. Wysocki <rafael@kernel.org>
2024-07-04Merge patch series "mpi3mr: Support PCI Error Recovery"Martin K. Petersen
Sumit Saxena <sumit.saxena@broadcom.com> says: This patch series contains the changes done in the driver to support PCI error recovery. It is rework of older patch series from Ranjan Kumar, see [1]. [1] https://lore.kernel.org/all/20231214205900.270488-1-ranjan.kumar@broadcom.com/ Link: https://lore.kernel.org/r/20240627101735.18286-1-sumit.saxena@broadcom.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: mpi3mr: Driver version updateSumit Saxena
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Link: https://lore.kernel.org/r/20240627101735.18286-4-sumit.saxena@broadcom.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: mpi3mr: Prevent PCI writes from driver during PCI error recoverySumit Saxena
Prevent interaction with the hardware while the error recovery in progress. Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com> Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com> Co-developed-by: Ranjan Kumar <ranjan.kumar@broadcom.com> Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Link: https://lore.kernel.org/r/20240627101735.18286-3-sumit.saxena@broadcom.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: mpi3mr: Support PCI Error Recovery callback handlersSumit Saxena
PCI Error recovery support is required to recover the controller upon detection of PCI errors. Add support for the PCI error recovery callback handlers in mpi3mr driver. Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com> Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com> Co-developed-by: Ranjan Kumar <ranjan.kumar@broadcom.com> Signed-off-by: Ranjan Kumar <ranjan.kumar@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Link: https://lore.kernel.org/r/20240627101735.18286-2-sumit.saxena@broadcom.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04Merge patch series "Update lpfc to revision 14.4.0.3"Martin K. Petersen
Justin Tee <justintee8345@gmail.com> says: Update lpfc to revision 14.4.0.3 This patch set contains bug fixes related to discovery, submission of mailbox commands, and proper endianness conversions. The patches were cut against Martin's 6.11/scsi-queue tree. Link: https://lore.kernel.org/r/20240628172011.25921-1-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Update lpfc version to 14.4.0.3Justin Tee
Update lpfc version to 14.4.0.3. Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-9-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Revise lpfc_prep_embed_io routine with proper endian macro usagesJustin Tee
On big endian architectures, it is possible to run into a memory out of bounds pointer dereference when FCP targets are zoned. In lpfc_prep_embed_io, the memcpy(ptr, fcp_cmnd, sgl->sge_len) is referencing a little endian formatted sgl->sge_len value. So, the memcpy can cause big endian systems to crash. Redefine the *sgl ptr as a struct sli4_sge_le to make it clear that we are referring to a little endian formatted data structure. And, update the routine with proper le32_to_cpu macro usages. Fixes: af20bb73ac25 ("scsi: lpfc: Add support for 32 byte CDBs") Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-8-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Fix incorrect request len mbox field when setting trunking via sysfsJustin Tee
When setting trunk modes through sysfs, the SLI_CONFIG mailbox command's command payload length is incorrectly hardcoded to 12 bytes. SLI_CONFIG's payload length field should be specified large enough to encompass both the submailbox command header and the submailbox request itself. Thus, replace the hardcoded 12 bytes with a clearer calculation by way of sizeof(struct lpfc_mbx_set_trunk_mode) - sizeof(struct lpfc_sli4_cfg_mhdr). Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-7-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Handle mailbox timeouts in lpfc_get_sfp_infoJustin Tee
The MBX_TIMEOUT return code is not handled in lpfc_get_sfp_info and the routine unconditionally frees submitted mailbox commands regardless of return status. The issue is that for MBX_TIMEOUT cases, when firmware returns SFP information at a later time, that same mailbox memory region references previously freed memory in its cmpl routine. Fix by adding checks for the MBX_TIMEOUT return code. During mailbox resource cleanup, check the mbox flag to make sure that the wait did not timeout. If the MBOX_WAKE flag is not set, then do not free the resources because it will be freed when firmware completes the mailbox at a later time in its cmpl routine. Also, increase the timeout from 30 to 60 seconds to accommodate boot scripts requiring longer timeouts. Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-6-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Fix handling of fully recovered fabric node in dev_loss callbkJustin Tee
In rare cases when a fabric node is recovered after a link bounce and before dev_loss_tmo callbk is reached, the driver may leave the fabric node in an inconsistent state with the NLP_IN_DEV_LOSS flag perpetually set. In lpfc_dev_loss_tmo_callbk, a check is added for a recovered fabric node. If the node is recovered, then don't queue the lpfc_dev_loss_tmo_handler work. In lpfc_dev_loss_tmo_handler, the path taken for the recovered fabric nodes is updated to clear the NLP_IN_DEV_LOSS flag. Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-5-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2024-07-04scsi: lpfc: Relax PRLI issue conditions after GID_FT responseJustin Tee
If previously in REG_LOGIN_ISSUE state, then remove the requirement that PLOGI must have been received from the remote port before issuing a PRLI. After GID_FT completes, it does not matter whether the driver itself sent a PLOGI or received one. The fact that we're in REG_LOGIN_ISSUE state simply means that the next state should be issuing the PRLI to continue discovery of the remote port. Signed-off-by: Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20240628172011.25921-4-justintee8345@gmail.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit (git 2.34.1) at 2025-09-20 17:46:43 +0000