| Age | Commit message (Collapse) | Author |
|---|
|
The HW supports this, use the S1DSS bits to configure the behavior
of SSID=0 which is the RID's translation.
If SSID's are currently being used in the CD table then just update the
S1DSS bits in the STE, remove the master_domain and leave ATS alone.
For iommufd the driver design has a small problem that all the unused CD
table entries are set with V=0 which will generate an event if VFIO
userspace tries to use the CD entry. This patch extends this problem to
include the RID as well if PASID is being used.
For BLOCKED with used PASIDs the
F_STREAM_DISABLED (STRTAB_STE_1_S1DSS_TERMINATE) event is generated on
untagged traffic and a substream CD table entry with V=0 (removed pasid)
will generate C_BAD_CD. Arguably there is no advantage to using S1DSS over
the CD entry 0 with V=0.
As we don't yet support PASID in iommufd this is a problem to resolve
later, possibly by using EPD0 for unused CD table entries instead of V=0,
and not using S1DSS for BLOCKED.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/11-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This removes all the notifier de-duplication logic in the driver and
relies on the core code to de-duplicate and allocate only one SVA domain
per mm per smmu instance. This naturally gives a 1:1 relationship between
SVA domain and mmu notifier.
It is a significant simplication of the flow, as we end up with a single
struct arm_smmu_domain for each MM and the invalidation can then be
shifted to properly use the masters list like S1/S2 do.
Remove all of the previous mmu_notifier, bond, shared cd, and cd refcount
logic entirely.
The logic here is tightly wound together with the unusued BTM
support. Since the BTM logic requires holding all the iommu_domains in a
global ASID xarray it conflicts with the design to have a single SVA
domain per PASID, as multiple SMMU instances will need to have different
domains.
Following patches resolve this by making the ASID xarray per-instance
instead of global. However, converting the BTM code over to this
methodology requires many changes.
Thus, since ARM_SMMU_FEAT_BTM is never enabled, remove the parts of the
BTM support for ASID sharing that interact with SVA as well.
A followup series is already working on fully enabling the BTM support,
that requires iommufd's VIOMMU feature to bring in the KVM's VMID as
well. It will come with an already written patch to bring back the ASID
sharing using a per-instance ASID xarray.
https://lore.kernel.org/linux-iommu/20240208151837.35068-1-shameerali.kolothum.thodi@huawei.com/
https://lore.kernel.org/linux-iommu/26-v6-228e7adf25eb+4155-smmuv3_newapi_p2_jgg@nvidia.com/
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/10-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Fill in the smmu_domain->devices list in the new struct arm_smmu_domain
that SVA allocates. Keep track of every SSID and master that is using the
domain reusing the logic for the RID attach.
This is the first step to making the SVA invalidation follow the same
design as S1/S2 invalidation. At present nothing will read this list.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/9-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently the SVA domain is a naked struct iommu_domain, allocate a struct
arm_smmu_domain instead.
This is necessary to be able to use the struct arm_master_domain
mechanism.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/8-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Allow creating and managing arm_smmu_mater_domain's with a non-zero SSID
through the arm_smmu_attach_*() family of functions. This triggers ATC
invalidation for the correct SSID in PASID cases and tracks the
per-attachment SSID in the struct arm_smmu_master_domain.
Generalize arm_smmu_attach_remove() to be able to remove SSID's as well by
ensuring the ATC for the PASID is flushed properly.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/7-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We no longer need a master->sva_enable to control what attaches are
allowed. Instead we can tell if the attach is legal based on the current
configuration of the master.
Keep track of the number of valid CD entries for SSID's in the cd_table
and if the cd_table has been installed in the STE directly so we know what
the configuration is.
The attach logic is then made into:
- SVA bind, check if the CD is installed
- RID attach of S2, block if SSIDs are used
- RID attach of IDENTITY/BLOCKING, block if SSIDs are used
arm_smmu_set_pasid() is already checking if it is possible to setup a CD
entry, at this patch it means the RID path already set a STE pointing at
the CD table.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/6-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Prepare to allow a S1 domain to be attached to a PASID as well. Keep track
of the SSID the domain is using on each master in the
arm_smmu_master_domain.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/5-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The core code allows the domain to be changed on the fly without a forced
stop in BLOCKED/IDENTITY. In this flow the driver should just continually
maintain the ATS with no change while the STE is updated.
ATS relies on a linked list smmu_domain->devices to keep track of which
masters have the domain programmed, but this list is also used by
arm_smmu_share_asid(), unrelated to ats.
Create two new functions to encapsulate this combined logic:
arm_smmu_attach_prepare()
<caller generates and sets the STE>
arm_smmu_attach_commit()
The two functions can sequence both enabling ATS and disabling across
the STE store. Have every update of the STE use this sequence.
Installing a S1/S2 domain always enables the ATS if the PCIe device
supports it.
The enable flow is now ordered differently to allow it to be hitless:
1) Add the master to the new smmu_domain->devices list
2) Program the STE
3) Enable ATS at PCIe
4) Remove the master from the old smmu_domain
This flow ensures that invalidations to either domain will generate an ATC
invalidation to the device while the STE is being switched. Thus we don't
need to turn off the ATS anymore for correctness.
The disable flow is the reverse:
1) Disable ATS at PCIe
2) Program the STE
3) Invalidate the ATC
4) Remove the master from the old smmu_domain
Move the nr_ats_masters adjustments to be close to the list
manipulations. It is a count of the number of ATS enabled masters
currently in the list. This is stricly before and after the STE/CD are
revised, and done under the list's spin_lock.
This is part of the bigger picture to allow changing the RID domain while
a PASID is in use. If a SVA PASID is relying on ATS to function then
changing the RID domain cannot just temporarily toggle ATS off without
also wrecking the SVA PASID. The new infrastructure here is organized so
that the PASID attach/detach flows will make use of it as well in
following patches.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/4-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The next patch will need to store the same master twice (with different
SSIDs), so allocate memory for each list element.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/3-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add arm_smmu_set_pasid()/arm_smmu_remove_pasid() which are to be used by
callers that already constructed the arm_smmu_cd they wish to program.
These functions will encapsulate the shared logic to setup a CD entry that
will be shared by SVA and S1 domain cases.
Prior fixes had already moved most of this logic up into
__arm_smmu_sva_bind(), move it to it's final home.
Following patches will relieve some of the remaining SVA restrictions:
- The RID domain is a S1 domain and has already setup the STE to point to
the CD table
- The programmed PASID is the mm_get_enqcmd_pasid()
- Nothing changes while SVA is running (sva_enable)
SVA invalidation will still iterate over the S1 domain's master list,
later patches will resolve that.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/2-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This allows the driver the receive the mm and always a device during
allocation. Later patches need this to properly setup the notifier when
the domain is first allocated.
Remove ops->domain_alloc() as SVA was the only remaining purpose.
Tested-by: Nicolin Chen <nicolinc@nvidia.com>
Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Michael Shavit <mshavit@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/1-v9-5cd718286059+79186-smmuv3_newapi_p2b_jgg@nvidia.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Fixes a sparse "different address spaces" error.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202406280050.syeEwLTE-lkp@intel.com/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/601612/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When using MSI/INTx interrupt, the shared interrupts are still being
handled in the device remove routine, before free IRQs. So isb memory
is still read after it is freed. Thus move wx_free_isb_resources()
from txgbe_close() to txgbe_remove(). And fix the improper isb free
action in txgbe_open() error handling path.
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Rename original txgbe_misc_irq_handle() to txgbe_misc_irq_thread_fn()
since it is the handle thread to wake up. And add the primary handler
to deal the case of MSI/INTx, because there is a schedule NAPI poll.
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When using MSI or INTx interrupts, request_irq() for pdev->irq will
conflict with request_threaded_irq() for txgbe->misc.irq, to cause
system crash. So remove txgbe_request_irq() for MSI/INTx case, and
rename txgbe_request_msix_irqs() since it only request for queue irqs.
Add wx->misc_irq_domain to determine whether the driver creates an IRQ
domain and threaded request the IRQs.
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When using MSI/INTx interrupts, wx->num_q_vectors is uninitialized.
Thus there will be kernel panic in wx_alloc_q_vectors() to allocate
queue vectors.
Fixes: 3f703186113f ("net: libwx: Add irq flow functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The __build_asserts() function only exists to have a place to put
build-time asserts.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407010401.rfunrBSx-lkp@intel.com/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/601606/
|
|
The global hci_hotkey_quickstart quirk flag is tested in
toshiba_acpi_enable_hotkeys() before the quirk flag is properly
initialized based on SMBIOS data. This causes the quirk to be
applied to all models, some of which behave erratically as a
result.
Fix this by initializing the global quirk flags during module
initialization before registering the ACPI driver. This also
allows us to mark toshiba_dmi_quirks[] as __initconst.
Fixes: 23f1d8b47d12 ("platform/x86: toshiba_acpi: Add quirk for buttons on Z830")
Reported-by: kemal <kmal@cock.li>
Closes: https://lore.kernel.org/platform-driver-x86/R4CYFS.TWB8QUU2SHWI1@cock.li/
Tested-by: kemal <kmal@cock.li>
Cc: stable@vger.kernel.org
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20240701194539.348937-1-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The round-robin path selector is inefficient in cases where there is a
difference in latency between paths. In the presence of one or more
high latency paths the round-robin selector continues to use the high
latency path equally. This results in a bias towards the highest latency
path and can cause a significant decrease in overall performance as IOs
pile on the highest latency path. This problem is acute with NVMe-oF
controllers.
The queue-depth path selector sends I/O down the path with the lowest
number of requests in its request queue. Paths with lower latency will
clear requests more quickly and have less requests queued compared to
higher latency paths. The goal of this path selector is to make more use
of lower latency paths which will bring down overall IO latency and
increase throughput and performance.
Signed-off-by: Thomas Song <tsong@purestorage.com>
[emilne: commandeered patch developed by Thomas Song @ Pure Storage]
Co-developed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Co-developed-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Link: https://lore.kernel.org/linux-nvme/20240509202929.831680-1-jmeneghi@redhat.com/
Tested-by: Marco Patalano <mpatalan@redhat.com>
Tested-by: Jyoti Rani <jrani@purestorage.com>
Tested-by: John Meneghini <jmeneghi@redhat.com>
Reviewed-by: Randy Jennings <randyj@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The mask parameter of syscfg property is mandatory for MP13 but
optional for all other cases.
The function should not return error code because for non-MP13
the missing syscfg phandle in DT is not considered an error.
So reset err to 0 in that case to support existing DTs without
syscfg phandle.
Fixes: 50bbc0393114 ("net: stmmac: dwmac-stm32: add management of stm32mp13 for stm32")
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
checking clk rate
When we want to use clock from RCC to clock Ethernet PHY (with ETHCK)
we need to check if value of clock rate is authorized.
If ETHCK is unused, the ETHCK frequency is 0Hz and validation fails.
It makes no sense to validate unused ETHCK, so skip the validation.
Fixes: 582ac134963e ("net: stmmac: dwmac-stm32: Separate out external clock rate validation")
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Correct member @num_por with size of right array @emac_v4_0_0_por for
struct ethqos_emac_driver_data @emac_v4_0_0_data.
Cc: stable@vger.kernel.org
Fixes: 8c4d92e82d50 ("net: stmmac: dwmac-qcom-ethqos: add support for emac4 on sa8775p platforms")
Signed-off-by: Yijie Yang <quic_yijiyang@quicinc.com>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20240701014720.2547856-1-quic_yijiyang@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Introduce Tx-Rx detection Time and Rx AEQ training mappings to
phy-airoha-pcie driver. This is a preliminary patch to introduce PCIe
support to En7581 SoC through the mediatek-gen3 PCIe driver.
This change is not introducing any backward compatibility issue since
the EN7581 dts is not upstream yet.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/edf3b28926177166c65256604d69f2f576cb6fb3.1719682943.git.lorenzo@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that this combo phy supports
both UTMI+ (HS) and PIPE3 (SS). It also supports DP alt mode.
The number of ports for UTMI+ and PIPE3 can be determined using the
LINKPORT register (which also exists on Exynos E850).
For SuperSpeed (SS) a new SS phy is in use and its PIPE3 interface is
new compared to Exynos E850, and also very different from the existing
support for older Exynos SoCs in this driver.
The SS phy needs a bit more configuration work and register tuning for
signal quality to work reliably, presumably due to the higher
frequency, e.g. to account for different board layouts. Additionally,
power needs to be enabled before writing to the SS phy registers.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-6-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Using the regulator_bulk APIs, the handling of power supplies becomes
much simpler. There is no need anymore to check if regulators have been
acquired or not, the bulk APIs will do all the work for us. We can also
drop the various handles to the individual power supplies in the driver
runtime data and instead simply treat them all as one thing. Error
cleanup also becomes much simpler.
Converting to the regulator_bulk APIs also makes it easier to add
support for those SoCs that have additional power supplies for the PHY.
Google Tensor gs101 is one example of such a SoC. Otherwise we'd have
to add all additional supplies individually via individual calls to
regulator_get() and enable/disable handle them all individually,
including complicated error handling. That doesn't scale and clutters
the code.
Just update the code to use the regulator_bulk APIs.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-5-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
In preparation for support for additional platforms, convert the phy
register access clock to using the clk_bulk interfaces.
Newer SoCs like Google Tensor gs101 require additional clocks for
access to additional (different) register areas (PHY, PMA, PCS), and
converting to clk_bulk simplifies addition of those extra clocks.
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-4-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Using the clk_bulk APIs, the clock handling for the core clocks becomes
much simpler. No need to check any flags whether or not certain clocks
exist or not. Further, we can drop the various handles to the
individual clocks in the driver data and instead simply treat them all
as one thing.
So far, this driver assumes that all platforms have a clock "ref". It
also assumes that the clocks "phy_pipe", "phy_utmi", and "itp" exist if
the platform data "has_common_clk_gate" is set to true. It then goes
and individually tries to acquire and enable and disable all the
individual clocks one by one. Rather than relying on these implicit
clocks and open-coding the clock handling, we can just explicitly spell
out the clock names in the different device data and use that
information to populate clk_bulk_data, allowing us to use the clk_bulk
APIs for managing the clocks.
As a side-effect, this change highlighted the fact that
exynos5_usbdrd_phy_power_on() forgot to check the result of the clock
enable calls. Using the clk_bulk APIs, the compiler now warns when
return values are not checked - therefore add the necessary check
instead of silently ignoring failures and continuing as if all is OK
when it isn't.
For consistency, also change a related dev_err() to dev_err_probe() in
exynos5_usbdrd_phy_clk_handle() to get consistent error message
formatting.
Finally, exynos5_usbdrd_phy_clk_handle() prints an error message in all
cases as necessary (except for -ENOMEM). There is no need to print
another message in its caller (the probe() function), and printing
errors during OOM conditions is usually discouraged. Drop the
duplicated message in exynos5_usbdrd_phy_probe().
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-3-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Some versions of this IP have been integrated using separate PMU power
control registers for the HS and SS parts. One example is the Google
Tensor gs101 SoC.
Such SoCs can now set pmu_offset_usbdrd0_phy_ss in their
exynos5_usbdrd_phy_drvdata for the SS phy to the appropriate value.
The existing 'usbdrdphy' alias can not be used in this case because
that is meant for determining the correct PMU offset if multiple
distinct PHYs exist in the system (as opposed to one PHY with multiple
isolators).
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240617-usb-phy-gs101-v3-2-b66de9ae7424@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
of_phy_put is used for of_phy_get to release the reference count.
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20240626080911.203630-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We actually want to calculate the alignment values first, then
use the alignment value to look up the data from reg_configs[].
Fixes: d3ab79553308 ("phy: starfive: Add mipi dphy tx support")
Reviewed-by: Shengyang Chen <shengyang.chen@starfivetech.com>
Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
Link: https://lore.kernel.org/r/20240627020059.163535-1-changhuang.liang@starfivetech.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for printing some basic status information to debugfs. This
is helpful when debugging phy consumers to make sure they are configuring
the phy appropriately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-6-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Take the phy mutex in xlate to protect against concurrent
modification/access to gtr_phy. This does not typically cause any
issues, since in most systems the phys are only xlated once and
thereafter accessed with the phy API (which takes the locks). However,
we are about to allow userspace to access phys for debugging, so it's
important to avoid any data races.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-5-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
For PCIe and DisplayPort, the phy instance represents the controller's
logical lane. Wait for the instance 0 phy's PLL to lock as other
instances will never lock. We do this in xpsgtr_wait_pll_lock so callers
don't have to determine the correct lane themselves.
The original comment is wrong about cumulative wait times. Since we are
just polling a bit, all subsequent waiters will finish immediately.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-4-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The phy "type" is just the combination of protocol and instance, and is
never used apart from that. Store the instance directly, instead of
converting to a type first. No functional change intended.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-3-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Lanes can use other lanes' reference clocks, as determined by refclk.
Use refclk to determine the clock to enable/disable instead of always
using the lane's own reference clock. This ensures the clock selected in
xpsgtr_configure_pll is the one enabled.
For the other half of the equation, always program REF_CLK_SEL even when
we are selecting the lane's own clock. This ensures that Linux's idea of
the reference clock matches the hardware. We use the "local" clock mux
for this instead of going through the ref clock network.
Fixes: 25d700833513 ("phy: xilinx: phy-zynqmp: dynamic clock support for power-save")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://lore.kernel.org/r/20240628205540.3098010-2-sean.anderson@linux.dev
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
cdns_torrent_dp_set_power_state() does not consider that ret might be
overwritten. Add return value check of regmap_read_poll_timeout() after
register read in cdns_torrent_dp_set_power_state().
Fixes: 5b16a790f18d ("phy: cadence-torrent: Reorder few functions to remove function declarations")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240702032042.3993031-1-make24@iscas.ac.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The word 'swtich' is wrong, so fix it.
Signed-off-by: Liu Jing <liujing@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20240701112517.6597-1-liujing@cmss.chinamobile.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Compile testing configurations without REGMAP support enabled results in
a bunch of errors being reported:
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:569:21: error: variable ‘rk_hdptx_phy_regmap_config’ has initializer but incomplete type
569 | static const struct regmap_config rk_hdptx_phy_regmap_config = {
| ^~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-samsung-hdptx.c:570:10: error: ‘const struct regmap_config’ has no member named ‘reg_bits’
570 | .reg_bits = 32,
| ^~~~~~~~
Note that selecting REGMAP alone is not enough, because of the following
liker error:
phy-rockchip-samsung-hdptx.c:(.text+0x10c): undefined reference to `__devm_regmap_init_mmio_clk'
Instead of the obvious fix to enable REGMAP_MMIO, select MFD_SYSCON,
which implicitly enables REGMAP_MMIO as well. The rationale is that the
driver has been already relying on the syscon functionality.
Moreover, without MFD_SYSCON enabled, the test coverage is reduced,
since the linker might not detect any potential undefined references
following syscon_regmap_lookup_by_phandle() invocation in
rk_hdptx_phy_probe() body. That is because the function would
unconditionally return -ENOTSUP, hence the compiler is free to optimize
out any unreachable code.
Finally ensure PHY_ROCKCHIP_SAMSUNG_HDPTX depends on HAS_IOMEM, as
required by MFD_SYSCON.
Fixes: 553be2830c5f ("phy: rockchip: Add Samsung HDMI/eDP Combo PHY driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20240629-rk-hdptx-compile-test-fix-v1-1-c86675ba8070@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Have bnxt call page_pool_disable_direct_recycling() to unlink the old
page pool when resetting a queue prior to destroying it, instead of
touching a netdev core struct directly.
Signed-off-by: David Wei <dw@davidwei.uk>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a check to cs_dsp_coeff_write_ctrl() to abort if the control
is not writeable.
The cs_dsp code originated as an ASoC driver (wm_adsp) where all
controls were exported as ALSA controls. It relied on ALSA to
enforce the read-only permission. Now that the code has been
separated from ALSA/ASoC it must perform its own permission check.
This isn't currently causing any problems so there shouldn't be any
need to backport this. If the client of cs_dsp exposes the control as
an ALSA control, it should set permissions on that ALSA control to
protect it. The few uses of cs_dsp_coeff_write_ctrl() inside drivers
are for writable controls.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://patch.msgid.link/20240702110809.16836-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
RCK is synchronize RC calibration. Driver triggers this calibration and
writes the result to registers.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-5-pkshih@realtek.com
|
|
DACK (digital-to-analog converters calibration) is used to calibrate DAC
to output signals as expected.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-4-pkshih@realtek.com
|
|
RX DCK stands for receiver DC calibration. With this calibration, we have
proper DC offset to reflect correct received signal strength indicator.
Do this calibration when bringing up interface and going to connect.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-3-pkshih@realtek.com
|
|
IQ signal calibration is a very important calibration to yield good RF
performance. We do this calibration once we are going to an AP. During
scanning phase, without this calibration RF performance is still
acceptable because it transmits and receives with low data rate at
this phase.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240627025849.25198-2-pkshih@realtek.com
|
|
Calculate a TX power constraint based on content of ieee80211 Transmit
Power Envelope (TPE). Since HW control registers aren't designed as many
as all kinds of TPE fields, we strictly intersect all TPE inputs in driver.
Then, according to result, constrain TX power via TX power limit/limit_RU.
Besides, extend dbgfs txpwr_table to show info about 6 GHz regulatory.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023237.7901-1-pkshih@realtek.com
|
|
Add additional policy option to let Bluetooth audio can play well
during Wi-Fi is hardware scanning.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240626023129.7776-1-pkshih@realtek.com
|
|
Cleanup the port map calculations, existing masks of having separate
masks for in and out ports is not really required.
Having a single mask for all the ports in the controller is simple and
cuts of some unnecessary code.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240618-soundwire-port-map-v1-1-9644e5545b9b@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Nothing prevents simultaneous ioctl calls to privcmd_irqfd_assign() and
privcmd_irqfd_deassign(). If that happens, it is possible that a kirqfd
created and added to the irqfds_list by privcmd_irqfd_assign() may get
removed by another thread executing privcmd_irqfd_deassign(), while the
former is still using it after dropping the locks.
This can lead to a situation where an already freed kirqfd instance may
be accessed and cause kernel oops.
Use SRCU locking to prevent the same, as is done for the KVM
implementation for irqfds.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/9e884af1f1f842eacbb7afc5672c8feb4dea7f3f.1718703669.git.viresh.kumar@linaro.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
irqfd_wakeup() gets EPOLLHUP, when it is called by
eventfd_release() by way of wake_up_poll(&ctx->wqh, EPOLLHUP), which
gets called under spin_lock_irqsave(). We can't use a mutex here as it
will lead to a deadlock.
Fix it by switching over to a spin lock.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/a66d7a7a9001424d432f52a9fc3931a1f345464f.1718703669.git.viresh.kumar@linaro.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
