| Age | Commit message (Collapse) | Author |
|---|
|
requires it
Setting up many of the registers for a new SPI transfer involves
unconditionally disabling the SPI controller, writing the register
value and re-enabling the controller. This is being done for registers
even when the value is unchanged and is also done for registers that
don't require the controller to be disabled for the change to take
effect. Make an effort to detect changes to the register values, and
only disables the controller if the new register value is different
and disabling the controller is required. This stops the controller
being repeated disabled and the bus going tristate before every
transfer.
Fixes: 9ac8d17694b6 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Steve Wilkins <steve.wilkins@raymarine.com>
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20240715-depict-twirl-7e592eeabaad@wendy
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
TX FIFO
Setting up many of the registers for a new SPI transfer requires the
SPI controller to be disabled after set_cs() has been called to assert
the chip select line. However, disabling the controller results in the
SCLK and MOSI output pins being tristate, which can cause clock
transitions to be seen by a slave device whilst SS is active. To fix
this, the CS is only set to inactive inline, whilst setting it active
is deferred until all registers are set up and the any controller
disables have been completed.
Fixes: 9ac8d17694b6 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Steve Wilkins <steve.wilkins@raymarine.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20240715-sanitizer-recant-dd96b7a97048@wendy
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is possible for the TXDONE interrupt be raised if the tx FIFO becomes
temporarily empty while transmitting, resulting in recursive calls to
mchp_corespi_write_fifo() and therefore a garbage message might be
transmitted depending on when the interrupt is triggered. Moving all of
the tx FIFO writes out of the TXDONE portion of the interrupt handler
avoids this problem.
Most of rest of the TXDONE portion of the handler is problematic too.
Only reading the rx FIFO (and finalising the transfer) when the TXDONE
interrupt is raised can cause the transfer to stall, if the final bytes
of rx data are not available in the rx FIFO when the final TXDONE
interrupt is raised. The transfer should be finalised regardless of
which interrupt is raised, provided that all tx data has been set and
all rx data received.
The first issue was encountered "in the wild", the second is
theoretical.
Fixes: 9ac8d17694b6 ("spi: add support for microchip fpga spi controllers")
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20240715-candied-deforest-585685ef3c8a@wendy
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Merge a miscellaneous ACPI change for 6.11-rc1:
- Add missing MODULE_DESCRIPTION() macros in two places (Jeff Johnson).
* acpi-misc:
ACPI: add missing MODULE_DESCRIPTION() macros
|
|
Merge changes in the ACPI processor and ACPI PAD drivers, ACPI
resources management quirks and ACPI backlight (video) driver
changes for 6.11-rc1:
- Downgrade Intel _OSC and _PDC messages in the ACPI processor driver
to debug to reduce log noise (Mario Limonciello).
- Still evaluate _OST when _PUR evaluation fails in the ACPI PAD
(processor aggregator) driver as per the spec (Armin Wolf).
- Skip ACPI IRQ override on Asus Vivobook Pro N6506MJ and N6506MU
platforms (Tamim Khan).
- Force native mode on some T2 macbooks in the ACPI backlight driver
and replace strcpy() with strscpy() in it (Orlando Chamberlain,
Muhammad Qasim Abdul Majeed).
* acpi-processor:
ACPI: processor: Downgrade Intel _OSC and _PDC messages to debug
* acpi-pad:
ACPI: acpi_pad: Still evaluate _OST when _PUR evaluation fails
* acpi-resource:
ACPI: resource: Skip IRQ override on Asus Vivobook Pro N6506MJ
ACPI: resource: Skip IRQ override on Asus Vivobook Pro N6506MU
* acpi-video:
ACPI: video: force native for some T2 macbooks
ACPI: video: Use strscpy() instead of strcpy()
|
|
Merge ACPI PMIC driver changes, updates related to the ACPI battery and
SBS drivers and NUMA-related ACPI updates for 6.11-rc1:
- Clean up the ACPI PMIC driver in multiple ways (Andy
Shevchenko, Christophe JAILLET).
- Add support for charge limiting state to the ACPI battery driver
and update _OSC to indicate support for it (Armin Wolf).
- Clean up the sysfs interface in the ACPI battery, SBS (smart battery
subsystem) and AC drivers (Thomas Weißschuh).
- Coordinate header includes in the ACPI NUMA code and make it use
ACCESS_COORDINATE_CPU when appropriate (Huang Ying, Thorsten Blum).
* acpi-pmic:
ACPI: PMIC: Constify struct pmic_table
ACPI: PMIC: Replace open coded be16_to_cpu()
ACPI: PMIC: Convert pr_*() to dev_*() printing macros
ACPI: PMIC: Use sizeof() instead of hard coded value
* acpi-battery:
ACPI: bus: Indicate support for battery charge limiting thru _OSC
ACPI: battery: Add support for charge limiting state
ACPI: SBS: manage alarm sysfs attribute through psy core
ACPI: battery: create alarm sysfs attribute atomically
ACPI: battery: use sysfs_emit over sprintf
ACPI: battery: constify powersupply properties
ACPI: SBS: constify powersupply properties
ACPI: AC: constify powersupply properties
* acpi-numa:
ACPI: NUMA: Consolidate header includes
ACPI: HMAT: Use ACCESS_COORDINATE_CPU when appropriate
|
|
Pull drm fixes from Dave Airlie:
"Oh I screwed up last week's fixes pull, and forgot to send..
Back to work, thanks to Sima for last week, not too many fixes as
expected getting close to release [ sic - Linus ], amdgpu and xe have
a couple each, and then some other misc ones.
amdgpu:
- PSR-SU fix
- Reseved VMID fix
xe:
- Use write-back caching mode for system memory on DGFX
- Do not leak object when finalizing hdcp gsc
bridge:
- adv7511 EDID irq fix
gma500:
- NULL mode fixes.
meson:
- fix resource leak"
* tag 'drm-fixes-2024-07-12' of https://gitlab.freedesktop.org/drm/kernel:
Revert "drm/amd/display: Reset freesync config before update new state"
drm/xe/display/xe_hdcp_gsc: Free arbiter on driver removal
drm/xe: Use write-back caching mode for system memory on DGFX
drm/amdgpu: reject gang submit on reserved VMIDs
drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes
drm/gma500: fix null pointer dereference in psb_intel_lvds_get_modes
drm/meson: fix canvas release in bind function
drm/bridge: adv7511: Fix Intermittent EDID failures
|
|
Merge changes in the ACPI x86-specific code, ACPI fan driverm ACPI LPSS
(Intel SoC) driver and the ACPI CPPC library for 6.11-rc1:
- Switch the ACPI x86 utility code and the ACPI LPSS driver to new
Intel CPU model defines (Tony Luck).
- Add hwmon interface support to the ACPI fan driver (Armin Wolf).
- Add sysfs entry for guaranteed performance to the ACPI CPPC library
and replace a ternary operator with umax() in it (Petr Tesařík,
Prabhakar Pujeri).
* acpi-x86:
ACPI: x86: Switch to new Intel CPU model defines
* acpi-fan:
ACPI: fan: Add hwmon support
* acpi-soc:
ACPI: LPSS: Switch to new Intel CPU model defines
* acpi-cppc:
ACPI: CPPC: Replace ternary operator with umax()
ACPI: CPPC: add sysfs entry for guaranteed performance
|
|
dasd_add_busid() can return an error via ERR_PTR() if an allocation
fails. However, two callsites in dasd_copy_pair_store() do not check
the result, potentially resulting in a NULL pointer dereference. Fix
this by checking the result with IS_ERR() and returning the error up
the stack.
Fixes: a91ff09d39f9b ("s390/dasd: add copy pair setup")
Signed-off-by: Carlos López <clopez@suse.de>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240715112434.2111291-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
With ARCH=s390, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/block/dasd_diag_mod.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/block/dasd_eckd_mod.o
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/s390/block/dasd_fba_mod.o
Add the missing invocations of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20240715112434.2111291-2-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Merge OPP (operating performance points) and tooling updates for
6.11-rc1:
- Fix missing cleanup on error in _opp_attach_genpd() (Viresh Kumar).
- Introduce an OF helper function to inform if required-opps is used
and drop a redundant in-parameter to _set_opp_level() (Ulf Hansson).
- Update pm-graph to v5.12 which includes fixes and major code revamp
for python3.12 (Todd Brandt).
- Address several assorted issues in the cpupower utility (Roman
Storozhenko).
* pm-opp:
OPP: Introduce an OF helper function to inform if required-opps is used
OPP: Drop a redundant in-parameter to _set_opp_level()
OPP: Fix missing cleanup on error in _opp_attach_genpd()
* pm-tools:
cpupower: fix lib default installation path
cpupower: Disable direct build of the 'bench' subproject
cpupower: Change the var type of the 'monitor' subcommand display mode
cpupower: Remove absent 'v' parameter from monitor man page
cpupower: Improve cpupower build process description
cpupower: Add 'help' target to the main Makefile
cpupower: Replace a dead reference link with working ones
pm-graph: v5.12, code revamp for python3.12
pm-graph: v5.12, fixes
|
|
Merge cpuidle and power capping changes for 6.11-rc1:
- Improve the teo cpuidle governor and clean up leftover comments from
the menu cpuidle governor (Christian Loehle).
- Clean up a comment typo in the teo cpuidle governor (Atul Kumar
Pant).
- Add missing MODULE_DESCRIPTION() macro to cpuidle haltpoll (Jeff
Johnson).
- Switch the intel_idle driver to new Intel CPU model defines (Tony
Luck).
- Switch the Intel RAPL driver new Intel CPU model defines (Tony Luck).
- Simplify if condition in the idle_inject driver (Thorsten Blum).
* pm-cpuidle:
cpuidle: teo: Don't count non-existent intercepts
cpuidle: teo: Remove recent intercepts metric
Revert: "cpuidle: teo: Introduce util-awareness"
cpuidle: governors: teo: Fix a typo in a comment
cpuidle: haltpoll: add missing MODULE_DESCRIPTION() macro
cpuidle: menu: Cleanup after loadavg removal
intel_idle: Switch to new Intel CPU model defines
* pm-powercap:
powercap: idle_inject: Simplify if condition
powercap: intel_rapl: Switch to new Intel CPU model defines
powercap: intel_rapl_msr: Switch to new Intel CPU model defines
|
|
Merge cpufreq changes for 6.11-rc1:
- Add Loongson-3 CPUFreq driver support (Huacai Chen).
- Add support for the Arrow Lake and Lunar Lake platforms and
the out-of-band (OOB) mode on Emerald Rapids to the intel_pstate
cpufreq driver, make it support the highest performance change
interrupt and clean it up (Srinivas Pandruvada).
- Switch cpufreq to new Intel CPU model defines (Tony Luck).
- Simplify the cpufreq driver interface by switching the .exit() driver
callback to the void return data type (Lizhe, Viresh Kumar).
- Make cpufreq_boost_enabled() return bool (Dhruva Gole).
- Add fast CPPC support to the amd-pstate cpufreq driver, address
multiple assorted issues in it and clean it up (Perry Yuan, Mario
Limonciello, Dhananjay Ugwekar, Meng Li, Xiaojian Du).
- Add Allwinner H700 speed bin to the sun50i cpufreq driver (Ryan
Walklin).
- Fix memory leaks and of_node_put() usage in the sun50i and qcom-nvmem
cpufreq drivers (Javier Carrasco).
- Clean up the sti and dt-platdev cpufreq drivers (Jeff Johnson,
Raphael Gallais-Pou).
- Fix deferred probe handling in the TI cpufreq driver and wrong return
values of ti_opp_supply_probe(), and add OPP tables for the AM62Ax and
AM62Px SoCs to it (Bryan Brattlof, Primoz Fiser).
- Avoid overflow of target_freq in .fast_switch() in the SCMI cpufreq
driver (Jagadeesh Kona).
- Use dev_err_probe() in every error path in probe in the Mediatek
cpufreq driver (Nícolas Prado).
- Fix kernel-doc param for longhaul_setstate in the longhaul cpufreq
driver (Yang Li).
- Fix system resume handling in the CPPC cpufreq driver (Riwen Lu).
* pm-cpufreq: (55 commits)
cpufreq: sti: fix build warning
cpufreq: mediatek: Use dev_err_probe in every error path in probe
cpufreq: Add Loongson-3 CPUFreq driver support
cpufreq: Make cpufreq_driver->exit() return void
cpufreq/amd-pstate: Fix the scaling_max_freq setting on shared memory CPPC systems
cpufreq/amd-pstate-ut: Convert nominal_freq to khz during comparisons
cpufreq: pcc: Remove empty exit() callback
cpufreq: loongson2: Remove empty exit() callback
cpufreq: nforce2: Remove empty exit() callback
cpufreq: docs: Add missing scaling_available_frequencies description
cpufreq: make cpufreq_boost_enabled() return bool
cpufreq: intel_pstate: Support highest performance change interrupt
x86/cpufeatures: Add HWP highest perf change feature flag
Documentation: cpufreq: amd-pstate: update doc for Per CPU boost control method
cpufreq: amd-pstate: Cap the CPPC.max_perf to nominal_perf if CPB is off
cpufreq: amd-pstate: initialize core precision boost state
cpufreq: acpi: move MSR_K7_HWCR_CPB_DIS_BIT into msr-index.h
cpufreq: sti: add missing MODULE_DEVICE_TABLE entry for stih418
cpufreq: intel_pstate: Replace boot_cpu_has()
cpufreq: ti: update OPP table for AM62Px SoCs
...
|
|
|
|
This reverts commit f7023b3d697c6a7dfe2d9c70e0d8c2c580ccbd76.
Russell indicates that assuming 32bits are sufficient isn't
necessarily safe.
Link: https://lore.kernel.org/20240711154741.174745-1-thorsten.blum@toblux.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Name it 'addr' instead of 'port' or 'phy'.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Link: https://patch.msgid.link/20240715123050.21202-1-ceggers@arri.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
`args->cfg[4]` is configured in Indirect Dispatch using the number of
batches. Currently, for all V3D tech versions, `args->cfg[4]` equals the
number of batches subtracted by 1. But, for V3D 7.1.6 and later, we must not
subtract 1 from the number of batches.
Implement the fix by checking the V3D tech version and revision.
Fixes several `dEQP-VK.synchronization*` CTS tests related to Indirect Dispatch.
Fixes: 18b8413b25b7 ("drm/v3d: Create a CPU job extension for a indirect CSD job")
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240714145243.1223131-2-mcanal@igalia.com
|
|
The V3D tech revision can be a useful information when configuring
jobs. Therefore, expose it in the `struct v3d_dev` with the V3D tech
version.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240714145243.1223131-1-mcanal@igalia.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- qca: use the power sequencer for QCA6390
- btusb: mediatek: add ISO data transmission functions
- hci_bcm4377: Add BCM4388 support
- btintel: Add support for BlazarU core
- btintel: Add support for Whale Peak2
- btnxpuart: Add support for AW693 A1 chipset
- btnxpuart: Add support for IW615 chipset
- btusb: Add Realtek RTL8852BE support ID 0x13d3:0x3591
* tag 'for-net-next-2024-07-15' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (71 commits)
Bluetooth: btmtk: Mark all stub functions as inline
Bluetooth: hci_qca: Fix build error
Bluetooth: hci_qca: use the power sequencer for wcn7850 and wcn6855
Bluetooth: hci_qca: make pwrseq calls the default if available
Bluetooth: hci_qca: unduplicate calls to hci_uart_register_device()
Bluetooth: hci_qca: schedule a devm action for disabling the clock
dt-bindings: bluetooth: qualcomm: describe the inputs from PMU for wcn7850
Bluetooth: btnxpuart: Fix warnings for suspend and resume functions
Bluetooth: btnxpuart: Add system suspend and resume handlers
Bluetooth: btnxpuart: Add support for IW615 chipset
Bluetooth: btnxpuart: Add support for AW693 A1 chipset
Bluetooth: btintel: Add support for Whale Peak2
Bluetooth: btintel: Add support for BlazarU core
Bluetooth: btusb: mediatek: add ISO data transmission functions
Bluetooth: btmtk: move btusb_recv_acl_mtk to btmtk.c
Bluetooth: btmtk: move btusb_mtk_[setup, shutdown] to btmtk.c
Bluetooth: btmtk: move btusb_mtk_hci_wmt_sync to btmtk.c
Bluetooth: btusb: add callback function in btusb suspend/resume
Bluetooth: btmtk: rename btmediatek_data
Bluetooth: btusb: mediatek: return error for failed reg access
...
====================
Link: https://patch.msgid.link/20240715142543.303944-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
First part of "net: Make timestamping selectable" from Kory Maincent.
Change the driver-facing type already to lower rebasing pain.
Link: https://lore.kernel.org/20240709-feature_ptp_netnext-v17-0-b5317f50df2a@bootlin.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In prevision to add new UAPI for hwtstamp we will be limited to the struct
ethtool_ts_info that is currently passed in fixed binary format through the
ETHTOOL_GET_TS_INFO ethtool ioctl. It would be good if new kernel code
already started operating on an extensible kernel variant of that
structure, similar in concept to struct kernel_hwtstamp_config vs struct
hwtstamp_config.
Since struct ethtool_ts_info is in include/uapi/linux/ethtool.h, here
we introduce the kernel-only structure in include/linux/ethtool.h.
The manual copy is then made in the function called by ETHTOOL_GET_TS_INFO.
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Acked-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-6-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change the API to select MAC default time stamping instead of the PHY.
Indeed the PHY is closer to the wire therefore theoretically it has less
delay than the MAC timestamping but the reality is different. Due to lower
time stamping clock frequency, latency in the MDIO bus and no PHC hardware
synchronization between different PHY, the PHY PTP is often less precise
than the MAC. The exception is for PHY designed specially for PTP case but
these devices are not very widespread. For not breaking the compatibility
default_timestamp flag has been introduced in phy_device that is set by
the phy driver to know we are using the old API behavior.
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240709-feature_ptp_netnext-v17-4-b5317f50df2a@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Initialize the completion before the mailbox channel is requested.
Fixes: 389711b37493 ("firmware: Add Turris Mox rWTM firmware driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
wait_for_completion_timeout()
The wait_for_completion_timeout() function returns 0 if timed out, and a
positive value if completed. Fix the usage of this function.
Fixes: 389711b37493 ("firmware: Add Turris Mox rWTM firmware driver")
Fixes: 2eab59cf0d20 ("firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Do not complete the "command done" completion if there are no waiters.
This can happen if a wait_for_completion() timed out or was interrupted.
Fixes: 389711b37493 ("firmware: Add Turris Mox rWTM firmware driver")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As the "rzg2l-usb-vbus-regulator" platform device is only created by
drivers/reset/reset-rzg2l-usbphy-ctrl.c, update the default stricter by
replacing ARCH_RZG2L->RESET_RZG2L_USBPHY_CTRL.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/all/CAMuHMdX5ayWbLEEa6nAipECVB6H9eCpRg21pu3zYrTdiER0F+Q@mail.gmail.com/
Link: https://patch.msgid.link/20240715134120.312610-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Several recent patches added static stubs to btmtk.h without the inline
keyword, which causes instances of -Wunused-function when those stubs
are not used anywhere in a file that includes the header:
In file included from drivers/bluetooth/btusb.c:28:
drivers/bluetooth/btmtk.h:254:13: warning: 'btmtk_fw_get_filename' defined but not used [-Wunused-function]
254 | static void btmtk_fw_get_filename(char *buf, size_t size, u32 dev_id,
| ^~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtk.h:249:12: warning: 'btmtk_process_coredump' defined but not used [-Wunused-function]
249 | static int btmtk_process_coredump(struct hci_dev *hdev, struct sk_buff *skb)
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtk.h:243:12: warning: 'btmtk_register_coredump' defined but not used [-Wunused-function]
243 | static int btmtk_register_coredump(struct hci_dev *hdev, const char *name,
| ^~~~~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtk.h:233:12: warning: 'btmtk_setup_firmware' defined but not used [-Wunused-function]
233 | static int btmtk_setup_firmware(struct hci_dev *hdev, const char *fwname,
| ^~~~~~~~~~~~~~~~~~~~
drivers/bluetooth/btmtk.h:227:12: warning: 'btmtk_setup_firmware_79xx' defined but not used [-Wunused-function]
227 | static int btmtk_setup_firmware_79xx(struct hci_dev *hdev, const char *fwname,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Add inline to all the stubs in btmtk.h (even ones that do not currently
have any warnings associated with them) to ensure there are never unused
function warnings from these stubs, as is customary for the kernel.
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the following build error introduced by b80f4e3b8cb8
("Bluetooth: hci_qca: schedule a devm action for disabling the clock"):
drivers/bluetooth/hci_qca.c: In function ‘qca_serdev_remove’:
drivers/bluetooth/hci_qca.c:2501:2: error: label at end of compound statement
2501 | default:
| ^~~~~~~
Fixes: b80f4e3b8cb8 ("Bluetooth: hci_qca: schedule a devm action for disabling the clock")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In preparation for using the power sequencing subsystem on sm8650 boards
and X13s laptop let's make pwrseq the default for wcn7850 and wcn6855.
Both these models require an enable GPIO so we can safely assume that if
the property is not there, then we should try to get the power
sequencer. Due to how the pwrseq lookup works - checking the provider at
run-time - we cannot really do it the other way around as we'd get stuck
forever on -EPROBE_DEFER.
If the relevant OF node does have the 'enable-gpios' property, we
fallback to the existing code for backward compatibility with older DTs.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If the device has a power sequencing handle, use it first. Otherwise
fall back to whatever code already exists.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Now that all three branches of the switch end up doing the same thing,
we can move the call to hci_uart_register_device() past it and unify the
error message.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
In preparation for unduplicating the hci_uart registration code,
schedule a devres action for disabling the SUSCLK rather than doing it
manually.
We cannot really use devm_clk_get_enabled() as we also set the rate
before enabling the clock. While this should in theory work, I don't
want to risk breaking existing users. One solution for the future is to
add devm_clk_get_enabled_with_rate() to the clock framework.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This fixes the warnings 'nxp_serdev_resume' and 'nxp_serdev_suspend'
defined but not used.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407100518.06Xxq5PK-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds handling for system suspend and resume. While the host enters
suspend state, the driver will drive the chip into low power state.
Similarly when system is resuming, the driver will wake up the chip.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for IW615 chipset with it's bootloader signature
and firmware file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds support for AW693 A1 chipset with it's bootloader signature
and firmware file.
No firmware name change needed for AW693 A0 chipset.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
from /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=09 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0039 Rev= 0.00
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add support for BlazarU core (CNVi).
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This patch implements functions for ISO data send and receive in btusb
driver for MediaTek's controller.
MediaTek defines a specific interrupt endpoint for ISO data transmissin
because the characteristics of interrupt endpoint are similar to the
application of ISO data which can support guaranteed transmissin
bandwidth, enough maximum data length and error checking mechanism.
Driver sets up ISO interface and endpoints in btusb_mtk_setup and clears
the setup in btusb_mtk_shutdown. These flow can't move to btmtk.c due to
btusb_driver is only defined in btusb.c when claiming/relaesing interface.
ISO packet anchor stops when driver suspending and resubmit interrupt urb
for ISO data when driver resuming.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move btusb_recv_acl_mtk from btusb.c to btmtk.c which holds
vendor specific stuff and would make btusb.c clean.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move btusb_mtk_[setup, shutdown] and related function from
btusb.c to btmtk.c which holds vendor specific stuff and
would make btusb.c clean.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Move btusb_mtk_hci_wmt_sync from btusb.c to btmtk.c which holds
vendor specific stuff and would make btusb.c clean.
Add usb.h header to btmtksdio.c/btmtkuart.c for usb related element
defined in btmtk.h
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add suspend/resum callback function in btusb_data which are reserved
for vendor specific usage during suspend/resume. hdev->suspend will be
added before stop traffic in btusb_suspend and hdev-> resume will be
added after resubmit urb in btusb_resume.
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Rename btmediatek_data to have a consistent prefix throughout the driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Update the code to immediately return an error code if accessing a
related register fails. This ensures that our desired logic for
subsequent register operations is maintained and allows us to promptly
catch any unexpected errors.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Remove the unnecessary goto tag whether there is an error or not, we have
to free the buffer at the end of the function.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add the support ID(0x13d3, 0x3591) to usb_device_id table for
Realtek RTL8852BE.
The device table is as follows:
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3591 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Cc: stable@vger.kernel.org
Signed-off-by: Wentao Guan <guanwentao@uniontech.com>
Signed-off-by: WangYuli <wangyuli@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Use INTEL_HW_VARIANT() instead of CNVi Id to decide to load Intermediate
Loader (IML) image. Fix the driver loading incorrect firmware for
BlazarU product.
dmesg:
.....
[146.111834] Bluetooth: hci0: Minimum firmware build 1 week 10 2014
[146.111839] Bluetooth: hci0: Bootloader timestamp 2022.18 buildtype 1 build 16362
[146.111848] Bluetooth: hci0: No support for _PRR ACPI method
[146.112204] Bluetooth: hci0: Failed to load Intel firmware file intel/ibt-0291-0291-iml.sfi (-2)
Fixes: 164c62f958f8 ("Bluetooth: btintel: Add firmware ID to firmware name")
Reported-by: Tsigan, Vladislav <vladislav.tsigan@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
We unnecessarily fallthrough the case for QCA6390 when initializing the
device and hit the condition where - due to the lack of the enable-gpio
- we disable power management despite using the power sequencer. We don't
need to look for clocks on this model so it makes more sense to just
register the hci device and break the switch.
Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 9a15ce685706 ("Bluetooth: qca: use the power sequencer for QCA6390")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
BT_HCIUART_QCA, which is a bool and an HCI UART component, uses now
power sequencing, so we need to be sure BT_HCIUART_QCA=y and
POWER_SEQUENCING=m cannot happen:
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_serdev_probe':
drivers/bluetooth/hci_qca.c:2401:(.text+0xc48): undefined reference to `devm_pwrseq_get'
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_shutdown':
drivers/bluetooth/hci_qca.c:2192:(.text+0x29e8): undefined reference to `pwrseq_power_off'
/usr/bin/aarch64-linux-gnu-ld: drivers/bluetooth/hci_qca.o: in function `qca_power_on':
drivers/bluetooth/hci_qca.c:1808:(.text+0x3390): undefined reference to `pwrseq_power_on'
Fixes: 9a15ce685706 ("Bluetooth: qca: use the power sequencer for QCA6390")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
