| Age | Commit message (Collapse) | Author |
|---|
|
When a reset occurring, it's supposed to recover user's configuration.
Currently, the port info(speed, duplex and autoneg) is stored in hclge_mac
and will be scheduled updated. Consider the case that reset was happened
consecutively. During the first reset, the port info is configured with
a temporary value cause the PHY is reset and looking for best link config.
Second reset start and use pervious configuration which is not the user's.
The specific process is as follows:
+------+ +----+ +----+
| USER | | PF | | HW |
+---+--+ +-+--+ +-+--+
| ethtool --reset | |
+------------------->| reset command |
| ethtool --reset +-------------------->|
+------------------->| +---+
| +---+ | |
| | |reset currently | | HW RESET
| | |and wait to do | |
| |<--+ | |
| | send pervious cfg |<--+
| | (1000M FULL AN_ON) |
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | reset command |<--+
| +-------------------->|
| | +---+
| | send pervious cfg | | HW RESET
| | (10M HALF AN_OFF) |<--+
| +-------------------->|
| | read cfg(time task) |
| | (10M HALF AN_OFF) +---+
| |<--------------------+ | cfg take effect
| | | |
| | read cfg(time task) |<--+
| | (10M HALF AN_OFF) |
| |<--------------------+
| | |
v v v
To avoid aboved situation, this patch introduced req_speed, req_duplex,
req_autoneg to store user's configuration and it only be used after
hardware reset and to recover user's configuration
Fixes: f5f2b3e4dcc0 ("net: hns3: add support for imp-controlled PHYs")
Signed-off-by: Peiyang Wang <wangpeiyang1@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before ORing the new clock rate with the control register value read
from the hardware, the existing clock rate needs to be masked off as
otherwise the existing value will interfere with the new one.
CC: stable@vger.kernel.org
Fixes: 8596124c4c1b ("spi: microchip-core-qspi: Add support for microchip fpga qspi controllers")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240508-fox-unpiloted-b97e1535627b@spud
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The third, and most likely the last, "new features" pull request for
v6.10 with changes both in stack and in drivers. In ath12k and rtw89
we disabled Wireless Extensions just like with iwlwifi earlier. Wi-Fi
7 devices will not support Wireless Extensions (WEXT) anymore so if
someone is still using the legacy WEXT interface it's time to switch
to nl80211 now!
We merged wireless into wireless-next as we decided not to send a
wireless pull request to v6.9 this late in the cycle. Also an
immutable branch with MHI subsystem was merged to get ath11k and
ath12k hibernation working.
Major changes:
mac80211/cfg80211
* handle color change per link
mt76
* mt7921 LED control
* mt7925 EHT radiotap support
* mt7920e PCI support
ath12k
* debugfs support
* dfs_simulate_radar debugfs file
* disable Wireless Extensions
* suspend and hibernation support
* ACPI support
* refactoring in preparation of multi-link support
ath11k
* support hibernation (required changes in qrtr and MHI subsystems)
* ieee80211-freq-limit Device Tree property support
ath10k
* firmware-name Device Tree property support
rtw89
* complete features of new WiFi 7 chip 8922AE including BT-coexistence
and WoWLAN
* use BIOS ACPI settings to set TX power and channels
* disable Wireless Extensios on Wi-Fi 7 devices
iwlwifi
* block_esr debugfs file
* support again firmware API 90 (was reverted earlier)
* provide channel survey information for Automatic Channel Selection (ACS)
* tag 'wireless-next-2024-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (214 commits)
wifi: mwl8k: initialize cmd->addr[] properly
wifi: iwlwifi: Ensure prph_mac dump includes all addresses
wifi: iwlwifi: mvm: don't request statistics in restart
wifi: iwlwifi: mvm: exit EMLSR if secondary link is not used
wifi: iwlwifi: mvm: add beacon template version 14
wifi: iwlwifi: mvm: align UATS naming with firmware
wifi: iwlwifi: Force SCU_ACTIVE for specific platforms
wifi: iwlwifi: mvm: record and return channel survey information
wifi: iwlwifi: mvm: add the firmware API for channel survey
wifi: iwlwifi: mvm: Fix race in scan completion
wifi: iwlwifi: mvm: Add a print for invalid link pair due to bandwidth
wifi: iwlwifi: mvm: add a debugfs for reading EMLSR blocking reasons
wifi: iwlwifi: mvm: Add active EMLSR blocking reasons prints
wifi: iwlwifi: bump FW API to 90 for BZ/SC devices
wifi: iwlwifi: mvm: fix primary link setting
wifi: iwlwifi: mvm: use already determined cmd_id
wifi: iwlwifi: mvm: don't reset link selection during restart
wifi: iwlwifi: Print EMLSR states name
wifi: iwlwifi: mvm: Block EMLSR when a p2p/softAP vif is active
wifi: iwlwifi: mvm: fix typo in debug print
...
====================
Link: https://lore.kernel.org/r/20240508120726.85A10C113CC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add NAPI support to netdevim, similar to veth.
* Add a nsim_rq rx queue structure to hold a NAPI instance and a skb
queue.
* During xmit, store the skb in the peer skb queue and schedule NAPI.
* During napi_poll(), drain the skb queue and pass up the stack.
* Add assoc between rxq and NAPI instance using netif_queue_set_napi().
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://lore.kernel.org/r/20240507163228.2066817-2-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Various ndo_set_config() methods can change dev->if_port
dev->if_port is going to be read locklessly from
rtnl_fill_link_ifmap().
Add corresponding WRITE_ONCE() on writer sides.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240507184144.1230469-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Information is stored in mr_sas_port->phy_mask, values larger then size of
this field shouldn't be allowed.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Link: https://lore.kernel.org/r/20240226151013.8653-1-thenzl@redhat.com
Acked-by: Sathya Prakash Veerichetty <sathya.prakash@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
btree_iter is used in two ways: either allocated on the stack with a
fixed size MAX_BSETS, or from a mempool with a dynamic size based on the
specific cache set. Previously, the struct had a fixed-length array of
size MAX_BSETS which was indexed out-of-bounds for the dynamically-sized
iterators, which causes UBSAN to complain.
This patch uses the same approach as in bcachefs's sort_iter and splits
the iterator into a btree_iter with a flexible array member and a
btree_iter_stack which embeds a btree_iter as well as a fixed-length
data array.
Cc: stable@vger.kernel.org
Closes: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2039368
Signed-off-by: Matthew Mirvish <matthew@mm12.xyz>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20240509011117.2697-3-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_max() is inclusive. So a -1 has been added when needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20240509011117.2697-2-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Nowadays *-objs list is just for user space programs.
This commit obsolete the usage, and simplify Makefile for firewire KUnit
tests since the tests are not composite objects.
Link: https://lore.kernel.org/r/20240508105351.532693-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
This reverts commit c37ce764cd492f044dcdbb39616298f02b0dbc7f.
RCCL library is currently not treating spatial partitions differently,
hence this change is causing issues. Revert temporarily till RCCL
implementation is ready for spatial partitions.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Limit the workaround introduced by commit 31729e8c21ec ("drm/amd/pm: fixes
a random hang in S4 for SMU v13.0.4/11") to only run in the s4 path.
Cc: Tim Huang <Tim.Huang@amd.com>
Fixes: 31729e8c21ec ("drm/amd/pm: fixes a random hang in S4 for SMU v13.0.4/11")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3351
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Some older MST hubs do not report DPCD registers according to
specification.
[How]
This change re-applies commit c53655545141 ("drm/amd/display: dsc mst
re-compute pbn for changes on hub").
With an additional check for these older MST devices.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Idle optimizations are blocked if there's more than one eDP connector
on the board - blocking S0i3 and IPS2 for static screen.
[How]
Fix the checks to correctly detect number of active eDP.
Also restrict the eDP support to panels that have correct feature
support.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
This fixes a bug introduced by commit c53655545141 ("drm/amd/display: dsc
mst re-compute pbn for changes on hub").
The change caused light-up issues with a second display that required
DSC on some MST docks.
[How]
Use Virtual DPCD for DSC caps in MST case.
[Limitations]
This change only affects MST DSC devices that follow specifications
additional changes are required to check for old MST DSC devices such as
ones which do not check for Virtual DPCD registers.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Underflow occurs when running Netflix in a 4k144 eDP + 4k60 HDMI FRL
setup. It is caused by latency varying based on the DCFCLK/FCLK state.
[How]
Enable urgent latency adjustment and match the reference to existing
ASIC that also see increased latency at low FCLK.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a couple of last minute fixes that came in over the previous
week, addressing:
- A pin configuration bug on a qualcomm board that caused issues with
ethernet and mmc
- Two minor code fixes for misleading console output in the microchip
firmware driver
- A build warning in the sifive cache driver"
* tag 'soc-fixes-6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
firmware: microchip: clarify that sizes and addresses are in hex
firmware: microchip: don't unconditionally print validation success
arm64: dts: qcom: sa8155p-adp: fix SDHC2 CD pin configuration
cache: sifive_ccache: Silence unused variable warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Update kernel-parameters doc to describe "pcie_aspm=off" more
accurately (Bjorn Helgaas)
- Restore the parent's (not the child's) ASPM state to the parent
during resume, which fixes a reboot during resume (Kai-Heng Feng)
* tag 'pci-v6.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/ASPM: Restore parent state to parent, child state to child
PCI/ASPM: Clarify that pcie_aspm=off means leave ASPM untouched
|
|
PCI_HEADER_TYPE_MULTIFUNC is define by e1000e and ixgbe and both are
unused. There is already PCI_HEADER_TYPE_MFD in pci_regs.h anyway which
should be used instead so remove the duplicated defines of it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During successful probe, igc logs this:
[ 5.133667] igc 0000:01:00.0 (unnamed net_device) (uninitialized): PHC added
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The reason is that igc_ptp_init() is called very early, even before
register_netdev() has been called. So the netdev_info() call works
on a partially uninitialized netdev.
Fix this by calling igc_ptp_init() after register_netdev(), right
after the media autosense check, just as in igb. Add a comment,
just as in igb.
Now the log message is fine:
[ 5.200987] igc 0000:01:00.0 eth0: PHC added
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ice_clear_dflt_vsi() is only removing default rule. Both default RX and
TX rule should be removed during release.
If it isn't switching to switchdev, second time results in error, because
TX filter is already there.
Fix it by removing the correct set of rules.
Fixes: 50d62022f455 ("ice: default Tx rule instead of to queue")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_match_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_match_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This driver currently doesn't support any control flags.
Use flow_rule_has_control_flags() to check for control flags,
such as can be set through `tc flower ... ip_flags frag`.
In case any control flags are masked, flow_rule_has_control_flags()
sets a NL extended error message, and we return -EOPNOTSUPP.
Only compile-tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This macro has the advantage over SET_SYSTEM_SLEEP_PM_OPS that we don't
have to care about when the functions are actually used.
Also make use of pm_sleep_ptr() to discard all PM_SLEEP related
stuff if CONFIG_PM_SLEEP isn't enabled.
Link: https://lore.kernel.org/lkml/20240417044459.1908-2-linux.amoon@gmail.com/
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
It is possible that the host connected and saw a cm established
event and started sending nvme capsules on the qp, however the
ctrl did not yet see an established event. This is why the
rsp_wait_list exists (for async handling of these cmds, we move
them to a pending list).
Furthermore, it is possible that the ctrl cm times out, resulting
in a connect-error cm event. in this case we hit a bad deref [1]
because in nvmet_rdma_free_rsps we assume that all the responses
are in the free list.
We are freeing the cmds array anyways, so don't even bother to
remove the rsp from the free_list. It is also guaranteed that we
are not racing anything when we are releasing the queue so no
other context accessing this array should be running.
[1]:
--
Workqueue: nvmet-free-wq nvmet_rdma_free_queue_work [nvmet_rdma]
[...]
pc : nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
lr : nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
Call trace:
nvmet_rdma_free_rsps+0x78/0xb8 [nvmet_rdma]
nvmet_rdma_free_queue_work+0x88/0x120 [nvmet_rdma]
process_one_work+0x1ec/0x4a0
worker_thread+0x48/0x490
kthread+0x158/0x160
ret_from_fork+0x10/0x18
--
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The nsid value is a u32 that comes from nvmet_req_find_ns(). It's
endian data and we're on an error path and both of those raise red
flags. So let's make this safer.
1) Make the buffer large enough for any u32.
2) Remove the unnecessary initialization.
3) Use snprintf() instead of sprintf() for even more safety.
4) The sprintf() function returns the number of bytes printed, not
counting the NUL terminator. It is impossible for the return value to
be <= 0 so delete that.
Fixes: 505363957fad ("nvmet: fix nvme status code when namespace is disabled")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The number of updated CPU capabilities per netlink event is hard-coded to
16. On systems with more than 16 CPUs (a common case), it takes more than
one thermal netlink event to relay all the new capabilities after an HFI
interrupt. This adds unnecessary overhead to both the kernel and user space
entities.
Increase the number of CPU capabilities updated per event to 64. Any system
with 64 CPUs or less can now update all the capabilities in a single
thermal netlink event.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When processing a hardware update, HFI generates as many thermal netlink
events as needed to relay all the updated CPU capabilities to user space.
The constant HFI_MAX_THERM_NOTIFY_COUNT is the number of CPU capabilities
updated per each of those events.
Give this constant a more descriptive name.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The delay between an HFI interrupt and its corresponding thermal netlink
event has so far been hard-coded to CONFIG_HZ jiffies (1 second). This
delay is too long for hardware that generates updates every tens of
milliseconds.
The HFI driver uses a delayed workqueue to send thermal netlink events. No
subsequent events will be sent if there is pending work.
As a result, much of the information of consecutive hardware updates will
be lost if the workqueue delay is too long. User space entities may act on
obsolete data. If the delay is too short, multiple events may overwhelm
listeners.
Set the delay to 100ms to strike a balance between too many and too few
events. Use milliseconds instead of jiffies to improve readability.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The name of the constant HFI_UPDATE_INTERVAL is misleading. It is not a
periodic interval at which HFI updates are processed. It is the delay in
the processing of an HFI update after the arrival of an HFI interrupt.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To address the performance drop issue, an optimization has been
implemented. The incorrect highest performance value previously set by the
low-level power firmware for AMD CPUs with Family ID 0x19 and Model ID
ranging from 0x70 to 0x7F series has been identified as the cause.
To resolve this, a check has been implemented to accurately determine the
CPU family and model ID. The correct highest performance value is now set
and the performance drop caused by the incorrect highest performance value
are eliminated.
Before the fix, the highest frequency was set to 4200MHz, now it is set
to 4971MHz which is correct.
CPU NODE SOCKET CORE L1d:L1i:L2:L3 ONLINE MAXMHZ MINMHZ MHZ
0 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
1 0 0 0 0:0:0:0 yes 4971.0000 400.0000 400.0000
2 0 0 1 1:1:1:0 yes 4971.0000 400.0000 4865.8140
3 0 0 1 1:1:1:0 yes 4971.0000 400.0000 400.0000
Fixes: f3a052391822 ("cpufreq: amd-pstate: Enable amd-pstate preferred core support")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218759
Signed-off-by: Perry Yuan <perry.yuan@amd.com>
Co-developed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Gaha Bana <gahabana@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently the ipq806x dwmac driver is almost always used attached to the
CPU port of a switch and phy-mode was always set to "rgmii" or "sgmii".
Some device came up with a special configuration where the PHY is
directly attached to the GMAC port and in those case phy-mode needs to
be set to "rgmii-id" to make the PHY correctly work and receive packets.
Since the driver supports only "rgmii" and "sgmii" mode, when "rgmii-id"
(or variants) mode is set, the mode is rejected and probe fails.
Add support also for these phy-modes to correctly setup PHYs that requires
delay applied to tx/rx.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Different revisions of the Marvell 88q2xxx phy needs different init
sequences.
Add init sequence for Rev B1 and Rev B2. Rev B2 init sequence skips one
register write.
Tested-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Signed-off-by: Gregor Herburger <gregor.herburger@ew.tq-group.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
802.1P (PCP) and DiffServ (DSCP) are handled now by DCB code. Let it do
all needed initial configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ8xxx variants
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches have different behavior on different ports:
- It seems to be not possible to disable VLAN PCP classification on port
2. It means, as soon as mutliqueue support is enabled, frames with
VLAN tag will get PCP prios. This behavior do not affect Port 1 -
it is possible to disable PCP prios.
- DSCP classification is not working on Port 2.
Since there are still usable configuration combinations, I added some
quirks to make sure user will get appropriate error message if not
possible configuration is chosen.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KSZ88X3 switches support up to 4 queues. Rework ksz8795_set_prio_queue()
to support KSZ8795 and KSZ88X3 families of switches.
Per default, configure KSZ88X3 to use one queue, since it need special
handling due to priority related errata. Errata handling is implemented
in a separate patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/drivers
A few more Qualcomm driver updates for v6.10
This fixes a sleep-while-atomic issue in pmic_glink, stemming from the
fact that the GLINK callback comes from interrupt context.
It fixes the Bluetooth address in the example of qcom,wcnss, and it
enables UEFI variables on SC8180X devices (Primus and Flex 5G).
* tag 'qcom-drivers-for-6.10-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
Link: https://lore.kernel.org/r/20240508020900.204413-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Both dma_unmap_sgtable() and sg_free_table() in spi_unmap_buf_attrs()
have checks for orig_nents against 0. No need to duplicate this.
All the same applies to other DMA mapping API calls.
Also note, there is no other user in the kernel that does this kind of
checks.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20240507201028.564630-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-05-06 (ice)
This series contains updates to ice driver only.
Paul adds support for additional E830 devices and adjusts naming for
existing E830 devices.
Marcin commonizes a couple of TC setup calls to reduce duplicated code.
Mateusz adds ice_vsi_cfg_params into ice_vsi to consolidate info.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: refactor struct ice_vsi_cfg_params to be inside of struct ice_vsi
ice: Deduplicate tc action setup
ice: update E830 device ids and comments
ice: add additional E830 device ids
====================
Link: https://lore.kernel.org/r/20240506170827.948682-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
