| Age | Commit message (Collapse) | Author |
|---|
|
Back in commit 826cff3f7ebb ("drm/bridge: parade-ps8640: Enable
runtime power management") we removed a mysterious 50 ms delay because
"Parade's support [couldn't] explain what the delay [was] for".
While I'm always a fan of removing mysterious delays, I suspect that
we need this mysterious delay to avoid some problems.
Specifically, what I found recently is that on sc7180-trogdor-homestar
sometimes the AUX backlight wasn't initializing properly. Some
debugging showed that the drm_dp_dpcd_read() function that the AUX
backlight driver was calling was returning bogus data about 1% of the
time when I booted up. This confused
drm_panel_dp_aux_backlight(). From continued debugging:
- If I retried the read then the read worked just fine.
- If I added a loop to perform the same read that
drm_panel_dp_aux_backlight() was doing 30 times at bootup I could
see that some percentage of the time the first read would give bogus
data but all 29 additional reads would always be fine.
- If I added a large delay _after_ powering on the panel but before
powering on PS8640 I could still reproduce the problem.
- If I added a delay after PS8640 powered on then I couldn't reproduce
the problem.
- I couldn't reproduce the problem on a board with the same panel but
the ti-sn65dsi86 bridge chip.
To me, the above indicated that there was a problem with PS8640 and
not the panel.
I don't really have any insight into what's going on in the MCU, but
my best guess is that when the MCU itself sees the HPD go high that it
does some AUX transfers itself and this is confusing things.
Let's go back and add back in the mysterious 50 ms delay. We only want
to do this the first time we see HPD go high after booting the MCU,
not every time we double-check HPD.
With this, the backlight initializes reliably on homestar.
Fixes: 826cff3f7ebb ("drm/bridge: parade-ps8640: Enable runtime power management")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017121813.1.I59700c745fbc31559a5d5c8e2a960279c751dbd5@changeid
|
|
The generic EFI stub can be instructed to avoid SetVirtualAddressMap(),
and simply run with the firmware's 1:1 mapping. In this case, it
populates the virtual address fields of the runtime regions in the
memory map with the physical address of each region, so that the mapping
code has to be none the wiser. Only if SetVirtualAddressMap() fails, the
virtual addresses are wiped and the kernel code knows that the regions
cannot be mapped.
However, wiping amounts to setting it to zero, and if a runtime region
happens to live at physical address 0, its valid 1:1 mapped virtual
address could be mistaken for a wiped field, resulting on loss of access
to the EFI services at runtime.
So let's only assume that VA == 0 means 'no runtime services' if the
region in question does not live at PA 0x0.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The linker script symbol definition that captures the size of the
compressed payload inside the zboot decompressor (which is exposed via
the image header) refers to '.' for the end of the region, which does
not give the correct result as the expression is not placed at the end
of the payload. So use the symbol name explicitly.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
To stop the bots from sending sparse warnings to me and the list about
efi_main() not having a prototype, decorate it with asmlinkage so that
it is clear that it is called from assembly, and therefore needs to
remain external, even if it is never declared in a header file.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Commit bbc6d2c6ef22 ("efi: vars: Switch to new wrapper layer")
refactored the efivars layer so that the 'business logic' related to
which UEFI variables affect the boot flow in which way could be moved
out of it, and into the efivarfs driver.
This inadvertently broke setting variables on firmware implementations
that lack the QueryVariableInfo() boot service, because we no longer
tolerate a EFI_UNSUPPORTED result from check_var_size() when calling
efivar_entry_set_get_size(), which now ends up calling check_var_size()
a second time inadvertently.
If QueryVariableInfo() is missing, we support writes of up to 64k -
let's move that logic into check_var_size(), and drop the redundant
call.
Cc: <stable@vger.kernel.org> # v6.0
Fixes: bbc6d2c6ef22 ("efi: vars: Switch to new wrapper layer")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Amadeusz reports KASAN use-after-free errors introduced by commit
3881ee0b1edc ("efi: avoid efivars layer when loading SSDTs from
variables"). The problem appears to be that the memory that holds the
new ACPI table is now freed unconditionally, instead of only when the
ACPI core reported a failure to load the table.
So let's fix this, by omitting the kfree() on success.
Cc: <stable@vger.kernel.org> # v6.0
Link: https://lore.kernel.org/all/a101a10a-4fbb-5fae-2e3c-76cf96ed8fbd@linux.intel.com/
Fixes: 3881ee0b1edc ("efi: avoid efivars layer when loading SSDTs from variables")
Reported-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The zboot decompressor series introduced a feature to sign the PE/COFF
kernel image for secure boot as part of the kernel build. This was
necessary because there are actually two images that need to be signed:
the kernel with the EFI stub attached, and the decompressor application.
This is a bit of a burden, because it means that the images must be
signed on the the same system that performs the build, and this is not
realistic for distros.
During the next cycle, we will introduce changes to the zboot code so
that the inner image no longer needs to be signed. This means that the
outer PE/COFF image can be handled as usual, and be signed later in the
release process.
Let's remove the associated Kconfig options now so that they don't end
up in a LTS release while already being deprecated.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
A splat from kmem_cache_destroy() was seen with a kernel prior to
commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool")
when there was a failure in init_dmars(), because the iommu_domain
cache still had objects. While the mempool code is now gone, there
still is a leak of the si_domain memory if init_dmars() fails. So
clean up si_domain in the init_dmars() error path.
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Will Deacon <will@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Fixes: 86080ccc223a ("iommu/vt-d: Allocate si_domain in init_dmars()")
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Link: https://lore.kernel.org/r/20221010144842.308890-1-jsnitsel@redhat.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit 5f64ce5411b46 ("iommu/vt-d: Duplicate iommu_resv_region objects
per device list") converted rcu_lock in get_resv_regions to
dmar_global_lock to allow sleeping in iommu_alloc_resv_region(). This
introduced possible recursive locking if get_resv_regions is called from
within a section where intel_iommu_init() already holds dmar_global_lock.
Especially, after commit 57365a04c921 ("iommu: Move bus setup to IOMMU
device registration"), below lockdep splats could always be seen.
============================================
WARNING: possible recursive locking detected
6.0.0-rc4+ #325 Tainted: G I
--------------------------------------------
swapper/0/1 is trying to acquire lock:
ffffffffa8a18c90 (dmar_global_lock){++++}-{3:3}, at:
intel_iommu_get_resv_regions+0x25/0x270
but task is already holding lock:
ffffffffa8a18c90 (dmar_global_lock){++++}-{3:3}, at:
intel_iommu_init+0x36d/0x6ea
...
Call Trace:
<TASK>
dump_stack_lvl+0x48/0x5f
__lock_acquire.cold.73+0xad/0x2bb
lock_acquire+0xc2/0x2e0
? intel_iommu_get_resv_regions+0x25/0x270
? lock_is_held_type+0x9d/0x110
down_read+0x42/0x150
? intel_iommu_get_resv_regions+0x25/0x270
intel_iommu_get_resv_regions+0x25/0x270
iommu_create_device_direct_mappings.isra.28+0x8d/0x1c0
? iommu_get_dma_cookie+0x6d/0x90
bus_iommu_probe+0x19f/0x2e0
iommu_device_register+0xd4/0x130
intel_iommu_init+0x3e1/0x6ea
? iommu_setup+0x289/0x289
? rdinit_setup+0x34/0x34
pci_iommu_init+0x12/0x3a
do_one_initcall+0x65/0x320
? rdinit_setup+0x34/0x34
? rcu_read_lock_sched_held+0x5a/0x80
kernel_init_freeable+0x28a/0x2f3
? rest_init+0x1b0/0x1b0
kernel_init+0x1a/0x130
ret_from_fork+0x1f/0x30
</TASK>
This rolls back dmar_global_lock to rcu_lock in get_resv_regions to avoid
the lockdep splat.
Fixes: 57365a04c921 ("iommu: Move bus setup to IOMMU device registration")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20220927053109.4053662-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Add gfp parameter to iommu_alloc_resv_region() for the callers to specify
the memory allocation behavior. Thus iommu_alloc_resv_region() could also
be available in critical contexts.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20220927053109.4053662-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Clean up the struct for hardware_path and drop the struct device_path
with a proper assignment of bc[] and mod members as signed chars.
This patch prepares for the kbuild change from Jason A. Donenfeld to
treat char as always unsigned.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The file name of this driver is misleading - it handles various serial
ports on parisc machines, not just such on the GSC bus.
Rename the file to make this clearer.
Suggested-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Although the name of the driver 8250_gsc.c suggests that it handles
only serial ports on the GSC bus, it does handle serial ports listed
in the parisc machine inventory as well, e.g. the serial ports in a
C8000 PCI-only workstation.
Change the dependency to CONFIG_PARISC, so that the driver gets included
in the kernel even if CONFIG_GSC isn't set.
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
This fixes maybe_unused warnings/errors.
According to a comment during device tree removal, only ACPI is supported,
thus let's actually require it.
Fixes: be18c5ede25d ("i2c: mlxbf: remove device tree support")
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Several types of UAFs can occur when physically removing a USB device.
Adds ufx_ops_destroy() function to .fb_destroy of fb_ops, and
in this function, there is kref_put() that finally calls ufx_free().
This fix prevents multiple UAFs.
Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Link: https://lore.kernel.org/linux-fbdev/20221011153436.GA4446@ubuntu/
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Commit 16ce101db85d ("mm/memory.c: fix race when faulting a device private
page") changed the migrate_to_ram() callback to take a reference on the
device page to ensure it can't be freed while handling the fault.
Unfortunately the corresponding update to Nouveau to accommodate this
change was inadvertently dropped from that patch causing GPU to CPU
migration to fail so add it here.
Link: https://lkml.kernel.org/r/20221019122934.866205-1-apopple@nvidia.com
Fixes: 16ce101db85d ("mm/memory.c: fix race when faulting a device private page")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
skb should be free in virtual_nci_send(), otherwise kmemleak will report
memleak.
Steps for reproduction (simulated in qemu):
cd tools/testing/selftests/nci
make
./nci_dev
BUG: memory leak
unreferenced object 0xffff888107588000 (size 208):
comm "nci_dev", pid 206, jiffies 4294945376 (age 368.248s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<000000008d94c8fd>] __alloc_skb+0x1da/0x290
[<00000000278bc7f8>] nci_send_cmd+0xa3/0x350
[<0000000081256a22>] nci_reset_req+0x6b/0xa0
[<000000009e721112>] __nci_request+0x90/0x250
[<000000005d556e59>] nci_dev_up+0x217/0x5b0
[<00000000e618ce62>] nfc_dev_up+0x114/0x220
[<00000000981e226b>] nfc_genl_dev_up+0x94/0xe0
[<000000009bb03517>] genl_family_rcv_msg_doit.isra.14+0x228/0x2d0
[<00000000b7f8c101>] genl_rcv_msg+0x35c/0x640
[<00000000c94075ff>] netlink_rcv_skb+0x11e/0x350
[<00000000440cfb1e>] genl_rcv+0x24/0x40
[<0000000062593b40>] netlink_unicast+0x43f/0x640
[<000000001d0b13cc>] netlink_sendmsg+0x73a/0xbf0
[<000000003272487f>] __sys_sendto+0x324/0x370
[<00000000ef9f1747>] __x64_sys_sendto+0xdd/0x1b0
[<000000001e437841>] do_syscall_64+0x3f/0x90
Fixes: e624e6c3e777 ("nfc: Add a virtual nci device driver")
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221020030505.15572-1-shangxiaojing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The `macb_resume`/`macb_suspend` methods already call the
`phylink_start`/`phylink_stop` methods during their execution so
explicitly say that the PM of the PHY is done by MAC by using the
`mac_managed_pm` flag of the `struct phylink_config`.
This also fixes the warning message issued during resume:
WARNING: CPU: 0 PID: 237 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0x144/0x148
Depends-on: 96de900ae78e ("net: phylink: add mac_managed_pm in phylink_config structure")
Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221019120929.63098-1-sergiu.moga@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In hinic_vf_func_init(), if VF fails to register information with PF
through the MBOX, the MBOX callback function of VF is released once. But
it is released again in hinic_init_hwdev(). Remove one.
Fixes: 7dd29ee12865 ("hinic: add sriov feature support")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When hinic_set_cmdq_depth() fails in hinic_init_cmdqs(), the cmdq memory is
not released correctly. Fix it.
Fixes: 72ef908bb3ff ("hinic: add three net_device_ops of vf")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the input parameter idx meets the expected case option in
hinic_dbg_get_func_table(), read_data is not released. Fix it.
Fixes: 5215e16244ee ("hinic: add support to query function table")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The value of lli_credit_cnt is incorrectly assigned, fix it.
Fixes: a0337c0dee68 ("hinic: add support to set and get irq coalesce")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently the rx drop is calculated as the sum of multiple HW drop
counters. The issue is that not all the HW drop counters were added for
the rx drop counter. So if for example you have a police that drops
frames, they were not see in the rx drop counter.
Fix this by updating how the rx drop counter is calculated. It is
required to add also RX_RED_PRIO_* HW counters.
Fixes: 12c2d0a5b8e2 ("net: lan966x: add ethtool configuration and statistics")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20221019083056.2744282-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221019064104.3228892-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Usual fixes for the week.
The amdgpu contains fixes for two regressions, one reported in
response to rc1 which broke on SI GPUs, and one gfx9 APU regression.
Otherwise it's mostly fixes for new IP, and some GPU reset fixes. vc4
is just HDMI fixes, and panfrost has some mnor types fixes.
Core:
- fix connector DDC pointer
- fix buffer overflow in format_helper_test
amdgpu:
- Mode2 reset fixes for Sienna Cichlid
- Revert broken fan speed sensor fix
- SMU 13.x fixes
- GC 11.x fixes
- RAS fixes
- SR-IOV fixes
- Fix BO move breakage on SI
- Misc compiler fixes
- Fix gfx9 APU regression caused by PCI AER fix
vc4:
- HDMI fixes
panfrost:
- compiler fixes"
* tag 'drm-fixes-2022-10-21' of git://anongit.freedesktop.org/drm/drm: (35 commits)
drm/amdgpu: fix sdma doorbell init ordering on APUs
drm/panfrost: replace endian-specific types with native ones
drm/panfrost: Remove type name from internal structs
drm/connector: Set DDC pointer in drmm_connector_init
drm: tests: Fix a buffer overflow in format_helper_test
drm/amdgpu: use DRM_SCHED_FENCE_DONT_PIPELINE for VM updates
drm/sched: add DRM_SCHED_FENCE_DONT_PIPELINE flag
drm/amdgpu: Fix for BO move issue
drm/amdgpu: dequeue mes scheduler during fini
drm/amd/pm: enable thermal alert on smu_v13_0_10
drm/amdgpu: Program GC registers through RLCG interface in gfx_v11/gmc_v11
drm/amdkfd: Fix type of reset_type parameter in hqd_destroy() callback
drm/amd/display: Increase frame size limit for display_mode_vba_util_32.o
drm/amd/pm: add SMU IP v13.0.4 IF version define to V7
drm/amd/pm: update SMU IP v13.0.4 driver interface version
drm/amd/pm: Init pm_attr_list when dpm is disabled
drm/amd/pm: disable cstate feature for gpu reset scenario
drm/amd/pm: fulfill SMU13.0.7 cstate control interface
drm/amd/pm: fulfill SMU13.0.0 cstate control interface
drm/amdgpu: Add sriov vf ras support in amdgpu_ras_asic_supported
...
|
|
Include the patches that weren't included in the 6.1 pull request.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter.
Current release - regressions:
- revert "net: fix cpu_max_bits_warn() usage in
netif_attrmask_next{,_and}"
- revert "net: sched: fq_codel: remove redundant resource cleanup in
fq_codel_init()"
- dsa: uninitialized variable in dsa_slave_netdevice_event()
- eth: sunhme: uninitialized variable in happy_meal_init()
Current release - new code bugs:
- eth: octeontx2: fix resource not freed after malloc
Previous releases - regressions:
- sched: fix return value of qdisc ingress handling on success
- sched: fix race condition in qdisc_graft()
- udp: update reuse->has_conns under reuseport_lock.
- tls: strp: make sure the TCP skbs do not have overlapping data
- hsr: avoid possible NULL deref in skb_clone()
- tipc: fix an information leak in tipc_topsrv_kern_subscr
- phylink: add mac_managed_pm in phylink_config structure
- eth: i40e: fix DMA mappings leak
- eth: hyperv: fix a RX-path warning
- eth: mtk: fix memory leaks
Previous releases - always broken:
- sched: cake: fix null pointer access issue when cake_init() fails"
* tag 'net-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (43 commits)
net: phy: dp83822: disable MDI crossover status change interrupt
net: sched: fix race condition in qdisc_graft()
net: hns: fix possible memory leak in hnae_ae_register()
wwan_hwsim: fix possible memory leak in wwan_hwsim_dev_new()
sfc: include vport_id in filter spec hash and equal()
genetlink: fix kdoc warnings
selftests: add selftest for chaining of tc ingress handling to egress
net: Fix return value of qdisc ingress handling on success
net: sched: sfb: fix null pointer access issue when sfb_init() fails
Revert "net: sched: fq_codel: remove redundant resource cleanup in fq_codel_init()"
net: sched: cake: fix null pointer access issue when cake_init() fails
ethernet: marvell: octeontx2 Fix resource not freed after malloc
netfilter: nf_tables: relax NFTA_SET_ELEM_KEY_END set flags requirements
netfilter: rpfilter/fib: Set ->flowic_uid correctly for user namespaces.
ionic: catch NULL pointer issue on reconfig
net: hsr: avoid possible NULL deref in skb_clone()
bnxt_en: fix memory leak in bnxt_nvm_test()
ip6mr: fix UAF issue in ip6mr_sk_done() when addrconf_init_net() failed
udp: Update reuse->has_conns under reuseport_lock.
net: ethernet: mediatek: ppe: Remove the unused function mtk_foe_entry_usable()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Several minor fixes:
- Fix the module alias for the ahci_imx driver to get autoloading to
work (Alexander)
- Fix a potential array-index-out-of-bounds problem with the
enclosure managment support in the ahci driver (Kai-Heng)
- Several patches to fix compilation warnings thrown by clang in the
ahci_st, sata_rcar, ahci_brcm, ahci_xgene, ahci_imx and ahci_qoriq
drivers (me)"
* tag 'ata-6.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: ahci_qoriq: Fix compilation warning
ata: ahci_imx: Fix compilation warning
ata: ahci_xgene: Fix compilation warning
ata: ahci_brcm: Fix compilation warning
ata: sata_rcar: Fix compilation warning
ata: ahci_st: Fix compilation warning
ata: ahci: Match EM_MAX_SLOTS with SATA_PMP_MAX_PORTS
ata: ahci-imx: Fix MODULE_ALIAS
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v6.1-rc2:
- Fix a buffer overflow in format_helper_test.
- Set DDC pointer in drmm_connector_init.
- Compiler fixes for panfrost.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c4d05683-8ebe-93b8-d24c-d1d2c68f12c4@linux.intel.com
|
|
Writes to the device must include an offset and size as defined in
CXL 2.0 8.2.9.5.2.4 Set LSA (Opcode 4103h)
Fixes tag is non obvious as this code has been through several
reworks and variable names + wasn't in use until the addition
of the region code.
Due to a bug in QEMU CXL emulation this overrun resulted in QEMU
crashing.
Reported-by: Bobo WL <lmw.bobo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 60b8f17215de ("cxl/pmem: Translate NVDIMM label commands to CXL label commands")
Link: https://lore.kernel.org/r/20220815154044.24733-3-Jonathan.Cameron@huawei.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Not all decoders have a commit callback.
The CXL specification allows a host bridge with a single root port to
have no explicit HDM decoders. Currently the region driver assumes there
are none. As such the CXL core creates a special pass through decoder
instance without a commit callback.
Prior to this patch, the ->commit() callback was called unconditionally.
Thus a configuration with 1 Host Bridge, 1 Root Port, 1 switch with
multiple downstream ports below which there are multiple CXL type 3
devices results in a situation where committing the region causes a null
pointer dereference.
Reported-by: Bobo WL <lmw.bobo@gmail.com>
Fixes: 176baefb2eb5 ("cxl/hdm: Commit decoder state to hardware")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20220818164210.2084-1-Jonathan.Cameron@huawei.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
A bug in the LSA code resulted in transfers slightly larger
than the mailbox size. Let us make it easier to catch similar
issues in future by adding a low level check.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220815154044.24733-2-Jonathan.Cameron@huawei.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.1-2022-10-20:
amdgpu:
- Fix gfx9 APU regression caused by PCI AER fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221020135225.562807-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.1-2022-10-19:
amdgpu:
- Mode2 reset fixes for Sienna Cichlid
- Revert broken fan speed sensor fix
- SMU 13.x fixes
- GC 11.x fixes
- RAS fixes
- SR-IOV fixes
- Fix BO move breakage on SI
- Misc compiler fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019191357.6208-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* vc4: HDMI fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y0gGdlujszCstDeP@linux-uq9g
|
|
cti_enable_hw() and cti_disable_hw() are called from an atomic context
so shouldn't use runtime PM because it can result in a sleep when
communicating with firmware.
Since commit 3c6656337852 ("Revert "firmware: arm_scmi: Add clock
management to the SCMI power domain""), this causes a hang on Juno when
running the Perf Coresight tests or running this command:
perf record -e cs_etm//u -- ls
This was also missed until the revert commit because pm_runtime_put()
was called with the wrong device until commit 692c9a499b28 ("coresight:
cti: Correct the parameter for pm_runtime_put")
With lock and scheduler debugging enabled the following is output:
coresight cti_sys0: cti_enable_hw -- dev:cti_sys0 parent: 20020000.cti
BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:1151
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 330, name: perf-exec
preempt_count: 2, expected: 0
RCU nest depth: 0, expected: 0
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [<0000000000000000>] 0x0
hardirqs last disabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last enabled at (0): [<ffff80000822b394>] copy_process+0xa0c/0x1948
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 3 PID: 330 Comm: perf-exec Not tainted 6.0.0-00053-g042116d99298 #7
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno Development Platform, BIOS EDK II Sep 13 2022
Call trace:
dump_backtrace+0x134/0x140
show_stack+0x20/0x58
dump_stack_lvl+0x8c/0xb8
dump_stack+0x18/0x34
__might_resched+0x180/0x228
__might_sleep+0x50/0x88
__pm_runtime_resume+0xac/0xb0
cti_enable+0x44/0x120
coresight_control_assoc_ectdev+0xc0/0x150
coresight_enable_path+0xb4/0x288
etm_event_start+0x138/0x170
etm_event_add+0x48/0x70
event_sched_in.isra.122+0xb4/0x280
merge_sched_in+0x1fc/0x3d0
visit_groups_merge.constprop.137+0x16c/0x4b0
ctx_sched_in+0x114/0x1f0
perf_event_sched_in+0x60/0x90
ctx_resched+0x68/0xb0
perf_event_exec+0x138/0x508
begin_new_exec+0x52c/0xd40
load_elf_binary+0x6b8/0x17d0
bprm_execve+0x360/0x7f8
do_execveat_common.isra.47+0x218/0x238
__arm64_sys_execve+0x48/0x60
invoke_syscall+0x4c/0x110
el0_svc_common.constprop.4+0xfc/0x120
do_el0_svc+0x34/0xc0
el0_svc+0x40/0x98
el0t_64_sync_handler+0x98/0xc0
el0t_64_sync+0x170/0x174
Fix the issue by removing the runtime PM calls completely. They are not
needed here because it must have already been done when building the
path for a trace.
Fixes: 835d722ba10a ("coresight: cti: Initial CoreSight CTI Driver")
Reported-by: Aishwarya TCV <Aishwarya.TCV@arm.com>
Reported-by: Cristian Marussi <Cristian.Marussi@arm.com>
Suggested-by: Suzuki Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Tested-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20221005131452.1506328-1-james.clark@arm.com
|
|
With lockdeps enabled, we get the following warning:
======================================================
WARNING: possible circular locking dependency detected
------------------------------------------------------
kworker/u12:1/53 is trying to acquire lock:
ffff80000adce220 (coresight_mutex){+.+.}-{4:4}, at: coresight_set_assoc_ectdev_mutex+0x3c/0x5c
but task is already holding lock:
ffff80000add1f60 (ect_mutex){+.+.}-{4:4}, at: cti_probe+0x318/0x394
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (ect_mutex){+.+.}-{4:4}:
__mutex_lock_common+0xd8/0xe60
mutex_lock_nested+0x44/0x50
cti_add_assoc_to_csdev+0x4c/0x184
coresight_register+0x2f0/0x314
tmc_probe+0x33c/0x414
-> #0 (coresight_mutex){+.+.}-{4:4}:
__lock_acquire+0x1a20/0x32d0
lock_acquire+0x160/0x308
__mutex_lock_common+0xd8/0xe60
mutex_lock_nested+0x44/0x50
coresight_set_assoc_ectdev_mutex+0x3c/0x5c
cti_update_conn_xrefs+0x6c/0xf8
cti_probe+0x33c/0x394
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(ect_mutex);
lock(coresight_mutex);
lock(ect_mutex);
lock(coresight_mutex);
*** DEADLOCK ***
4 locks held by kworker/u12:1/53:
#0: ((wq_completion)events_unbound){+.+.}-{0:0}, at: process_one_work+0x1fc/0x63c
#1: (deferred_probe_work){+.+.}-{0:0}, at: process_one_work+0x228/0x63c
#2: (&dev->mutex){....}-{4:4}, at: __device_attach+0x48/0x1a8
#3: (ect_mutex){+.+.}-{4:4}, at: cti_probe+0x318/0x394
To fix the same, call cti_add_assoc_to_csdev without the holding
coresight_mutex and confine the locking while setting the associated
ect / cti device using coresight_set_assoc_ectdev_mutex().
Fixes: 177af8285b59 ("coresight: cti: Enable CTI associated with devices")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20220721130329.3787211-1-sudeep.holla@arm.com
|
|
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for sis630
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Commit 8795e182b02d ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
uncovered a bug in amdgpu that required a reordering of the driver
init sequence to avoid accessing a special register on the GPU
before it was properly set up leading to an PCI AER error. This
reordering uncovered a different hw programming ordering dependency
in some APUs where the SDMA doorbells need to be programmed before
the GFX doorbells. To fix this, move the SDMA doorbell programming
back into the soc15 common code, but use the actual doorbell range
values directly rather than the values stored in the ring structure
since those will not be initialized at this point.
This is a partial revert, but with the doorbell assignment
fixed so the proper doorbell index is set before it's used.
Fixes: e3163bc8ffdfdb ("drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: skhan@linuxfoundation.org
Cc: stable@vger.kernel.org
|
|
Commit c347a787e34cb (drbd: set ->bi_bdev in drbd_req_new) moved a
bio_set_dev call (which has since been removed) to "earlier", from
drbd_request_prepare to drbd_req_new.
The problem is that this accesses device->ldev->backing_bdev, which is
not NULL-checked at this point. When we don't have an ldev (i.e. when
the DRBD device is diskless), this leads to a null pointer deref.
So, only allocate the private_bio if we actually have a disk. This is
also a small optimization, since we don't clone the bio to only to
immediately free it again in the diskless case.
Fixes: c347a787e34cb ("drbd: set ->bi_bdev in drbd_req_new")
Co-developed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Signed-off-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Co-developed-by: Joel Colledge <joel.colledge@linbit.com>
Signed-off-by: Joel Colledge <joel.colledge@linbit.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20221020085205.129090-1-christoph.boehmwalder@linbit.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 6.1
- fix nvme-hwmon for DMA non-cohehrent architectures (Serge Semin)
- add a nvme-hwmong maintainer (Christoph Hellwig)
- fix error pointer dereference in error handling (Dan Carpenter)
- fix invalid memory reference in nvmet_subsys_attr_qid_max_show
(Daniel Wagner)
- don't limit the DMA segment size in nvme-apple (Russell King)
- fix workqueue MEM_RECLAIM flushing dependency (Sagi Grimberg)
- disable write zeroes on various Kingston SSDs (Xander Li)"
* tag 'nvme-6.1-2022-10-22' of git://git.infradead.org/nvme:
nvmet: fix invalid memory reference in nvmet_subsys_attr_qid_max_show
nvmet: fix workqueue MEM_RECLAIM flushing dependency
nvme-hwmon: kmalloc the NVME SMART log buffer
nvme-hwmon: consistently ignore errors from nvme_hwmon_init
nvme: add Guenther as nvme-hwmon maintainer
nvme-apple: don't limit DMA segement size
nvme-pci: disable write zeroes on various Kingston SSD
nvme: fix error pointer dereference in error handling
|
|
Update the driver to use an immutable IRQ chip to fix this warning:
"not an immutable chip, please consider fixing it!"
Preserve per-chip labels by adding an ->irq_print_chip() callback.
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # TF201 T30
Tested-by: Robert Eckelmann <longnoserob@gmail.com> # TF101 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
__le32 and __le64 types aren't portable and are not available on
FreeBSD (which uses the same uAPI).
Instead of attempting to always output little endian, just use native
endianness in the dumps. Tools can detect the endianness in use by
looking at the 'magic' field, but equally we don't expect big-endian to
be used with Mali (there are no known implementations out there).
Bug: https://gitlab.freedesktop.org/mesa/mesa/-/issues/7252
Fixes: 730c2bf4ad39 ("drm/panfrost: Add support for devcoredump")
Reviewed-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017104602.142992-3-steven.price@arm.com
|
|
Commit 35a3b82f1bdd ("drm/connector: Introduce drmm_connector_init")
introduced the function drmm_connector_init() with a parameter for an
optional ddc pointer to the i2c controller used to access the DDC bus.
However, the underlying call to __drm_connector_init() was always
setting it to NULL instead of passing the ddc argument around.
This resulted in unexpected null pointer dereference on platforms
expecting to get a DDC controller.
Fixes: 35a3b82f1bdd ("drm/connector: Introduce drmm_connector_init")
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20221019143442.1798964-1-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The xrgb2101010 format conversion test (unlike for other formats) does
an endianness conversion on the results. However, it always converts
TEST_BUF_SIZE 32-bit integers, which results in reading from (and
writing to) more memory than in present in the result buffer. Instead,
use the buffer size, divided by sizeof(u32).
The issue could be reproduced with KASAN:
./tools/testing/kunit/kunit.py run --kunitconfig drivers/gpu/drm/tests \
--kconfig_add CONFIG_KASAN=y --kconfig_add CONFIG_KASAN_VMALLOC=y \
--kconfig_add CONFIG_KASAN_KUNIT_TEST=y \
drm_format_helper_test.*xrgb2101010
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Fixes: 453114319699 ("drm/format-helper: Add KUnit tests for drm_fb_xrgb8888_to_xrgb2101010()")
Signed-off-by: David Gow <davidgow@google.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019073239.3779180-1-davidgow@google.com
|
|
Backmerging to get v6.1-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
The function xilinxfb_release() returns zero unconditionally. Make it
return void. There is no semantic change, the only effect is that it
becomes obvious that the driver's .remove() callback always returns zero.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
If the cable is disconnected the PHY seems to toggle between MDI and
MDI-X modes. With the MDI crossover status interrupt active this causes
roughly 10 interrupts per second.
As the crossover status isn't checked by the driver, the interrupt can
be disabled to reduce the interrupt load.
Fixes: 87461f7a58ab ("net: phy: DP83822 initial driver submission")
Signed-off-by: Felix Riemann <felix.riemann@sma.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221018104755.30025-1-svc.sw.rte.linux@sma.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eliminate the following coccicheck warning:
./drivers/block/ublk_drv.c:127:16-19: WARNING use flexible-array member instead
Signed-off-by: Yushan Zhou <katrinzhou@tencent.com>
Link: https://lore.kernel.org/r/20221018100132.355393-1-zys.zljxml@gmail.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
